Alloyed Zn(x)Cd(1-x)S nanocrystals with highly narrow luminescence spectral width

High-quality alloyed Zn(x)Cd(1-x)S nanocrystals have been synthesized at high temperature by the reaction of a mixture of CdO- and ZnO-oleic acid complexes with sulfur in the noncoordinating solvent octadecene system. A series of monodisperse wurtzite Zn(x)Cd(1-x)S (x = 0.10, 0.25, 0.36, 0.53) nanocrystals were obtained with corresponding particle radii of 4.0, 3.2, 2.9, and 2.4 nm, respectively. With the increase of the Zn content, their photoluminescence (PL) spectra blue-shift systematically across the visible spectrum from 474 to 391 nm, indicating the formation of the alloyed nanocrystals. The alloy structure is also supported by the characteristic X-ray diffraction (XRD) patterns of these nanoalloys with different Zn mole fractions, in which their diffraction peaks systematically shift to larger angles as the Zn content increases. The lattice parameter c measured from XRD patterns decreases linearly with the increase of Zn content. This trend is consistent with Vegard's law, which further confirms the formation of homogeneous nanoalloys. These monodisperse wurtzite Zn(x)Cd(1-x)S nanoalloys possess superior optical properties with PL quantum yields of 25-50%, especially the extremely narrow room-temperature emission spectral width (full width at half-maximum, fwhm) of 14-18 nm. The obtained narrow spectral width stems from the uniform size and shape distribution, the high composition homogeneity, and the relatively large particle radius, which is close to or somewhat larger than the exciton Bohr radius. The process by which the initial structure with random spatial composition fluctuations turns into an alloy (solid solution) with homogeneous composition is clearly demonstrated by the temporal evolution of the PL spectra during the annealing progress.     

Composition-tunable Zn(x)Cd(1-x)Se nanocrystals with high luminescence and stability

High-quality Zn(x)Cd(1-x)Se nanocrystals have been successfully prepared at high temperature by incorporating stoichiometric amounts of Zn and Se into pre-prepared CdSe nanocrystals. With increasing Zn content, a composition-tunable emission across most of the visible spectrum has been demonstrated by a systematic blue-shift in emission wavelength. The photoluminescence (PL) properties for the obtained Zn(x)Cd(1-x)Se nanocrystals (PL efficiency of 70-85%, fwhm = 22-30 nm) are comparable to those for the best reported CdSe-based QDs. In particular, they also have good PL properties in the blue spectral range. Moreover, the alloy nanocrystals can retain their high luminescence (PL efficiency of over 40%) when dispersed in aqueous solutions and maintain a symmetric peak shape and spectral position under rigorous experimental conditions. A rapid alloying process was observed at a temperature higher than "alloying point". The mechanism of the high luminescence efficiency and stability of Zn(x)Cd(1-x)Se nanocrystals is explored.     

One-pot synthesis of Cu1.94S-CdS and Cu1.94S-Zn(x)Cd(1-x)S nanodisk heterostructures

Nanodisk heterostructures consisting of monoclinic Cu(1.94)S and wurtzite CdS have been colloidally synthesized for the first time. Initially, hexagonal-shaped nanodisks of Cu(1.94)S were produced upon thermolysis of a copper complex in a solvent mixture of HDA and TOA at 250 °C. Rapid addition of Cd precursor to the reaction mixture resulted in the partial conversion of Cu(1.94)S into CdS, yielding Cu(1.94)S-CdS nanoheterostructures. The original morphology of the Cu(1.94)S nanodisks was conserved during the transformation. When Zn precursor was added together with the Cd precursor, Cu(1.94)S-Zn(x)Cd(1-x)S nanodisks were generated. These two-component nanostructures are potentially useful in the fabrication of heterojunction solar cells.     

Alloyed (ZnSe)(x)(CuInSe2)(1-x) and CuInSe(x)S(2-x) nanocrystals with a monophase zinc blende structure over the entire composition range

Metastable zinc blende CuInSe(2) nanocrystals were synthesized by a hot-injection approach. It was found that the lattice mismatches between zinc blende CuInSe(2) and ZnSe as well as CuInSe(2) and CuInS(2) are only 2.0% and 4.6%, respectively. Thus, alloyed (ZnSe)(x)(CuInSe(2))(1-x) and CuInSe(x)S(2-x) nanocrystals with a zinc blende structure have been successfully synthesized over the entire composition range, and the band gaps of alloys can be tuned in the range from 2.82 to 0.96 eV and 1.43 to 0.98 eV, respectively. These alloyed (ZnSe)(x)(CuInSe(2))(1-x) and CuInSe(x)S(2-x) nanocrystals with a broad tunable band gap have a high potential for photovoltaic and photocatalytic applications.     

Synthesis of shape-controlled monodisperse wurtzite CuIn(x)Ga(1-x)S2 semiconductor nanocrystals with tunable band gap

Monodisperse wurtzite CuIn(x)Ga(1-x)S(2) nanocrystals have been synthesized over the entire composition range using a facile solution-based method. Depending on the chemical composition and synthesis conditions, the morphology of the nanocrystals can be controlled in the form of bullet-like, rod-like, and tadpole-like shapes. The band gap of the nanocrystals increases linearly with increasing Ga concentration, with band gap values for the end members being close to those observed in the bulk. Colloidal suspensions of the nanocrystals are attractive for use as inks for low-cost fabrication of thin film solar cells by spin or spray coating.     

Large scale synthesis of stable tricolor Zn(1-x)Cd(x)Se core/multishell nanocrystals via a facile phosphine-free colloidal method

Here we report a new "green" method to synthesize Zn(1-x)Cd(x)Se (x = 0-1) and stable red-green-blue tricolor Zn(1-x)Cd(x)Se core/shell nanocrystals using only low cost, phosphine-free and environmentally friendly reagents. The first excitonic absorption peak and photoluminescence (PL) position of the Zn(1-x)Cd(x)Se nanocrystals (the value of x is in the range 0.005-0.2) can be fixed to any position in the range 456-540 nm. There is no red or blue shift in the entire reaction process. Three similar sizes of alloyed Zn(1-x)Cd(x)Se nanocrystals with blue, green, and yellow emissions were successfully selected as cores to synthesize high quality blue, green, and red core/shell nanocrystal emitters. For the synthesis of core/shell nanocrystals with a high quantum yield (QY) and stability, the selection of shell materials has been proven to be very important. Therefore, alternative protocols have been used to optimize thick shell growth. ZnSe/ZnSe(x)S(1-x) and CdS/Zn(1-x)Cd(x)S have been found as an excellent middle multishell to overcoat between the alloyed Zn(1-x)Cd(x)Se core and ZnS outshell. The QYs of the as-synthesized core/shell alloyed Zn(1-x)Cd(x)Se nanocrystals can reach 40-75%. The Cd content is reduced to less than 0.1% for Zn(1 -x)Cd(x)Se core/shell nanocrystals with emissions in the range 456-540 nm. More than 15 g of high quality Zn(1-x)Cd(x)Se core/shell nanocrystals were prepared successfully in a large scale, one-pot reaction. Importantly, the emissions of such thick multishell nanocrystals are not susceptible to ligand loss and stability in various physiological conditions.     

The first synthesis of Pb(1-x)Mn(x)Se nanocrystals

In this work, Mn-doped PbSe nanocrystals (NCs) have been, for the first time, prepared through a high-temperature organic solution approach. To ensure that all the Mn2+ ions are indeed incorporated into the NCs and not only physically presented at the surface, Mn-Se prebonded precursor was selected, and a ligand-exchange process was also conducted before and after the synthesis, respectively. Various analyses including EDS, ICP, XRD, SQUID, and EPR confirm that the Mn2+ ions have been successfully doped into PbSe NCs.     

Highly luminescent CdSe/Cd(x)Zn(1-x)S quantum dots coated with thickness-controlled SiO2 shell through silanization

A silanization technique of hydrophobic quantum dots (QDs) was applied to SiO(2)-coated CdSe/Cd(x)Zn(1-x)S QDs to precisely control the SiO(2) shell thickness and retain the original high photoluminescence (PL) properties of the QDs. Hydrophobic CdSe/Cd(x)Zn(1-x)S core-shell QDs with PL peak wavelengths of 600 and 652 nm were prepared by a facile organic route by using oleic acid (OA) as a capping agent. The QDs were silanized by using partially hydrolyzed tetraethyl orthosilicate by replacing surface OA. These silanized QDs were subsequently encapsulated in a SiO(2) shell by a reverse micelles synthesis. The silanization plays an important role for the QDs to be coated with a homogeneous SiO(2) shell and retain a high PL efficiency in water. Transmission electron microscopy observation shows that the shells are 1-9 nm with final particle sizes of 10-25 nm, depending on the initial QD size. In the case of short reaction time (6 h), the QDs were coated with a very thin SiO(2) layer because no visible SiO(2) shell was observed but transferred into the water phase. The silica coating does not change the PL peak wavelength of the QDs. The full width at half-maximum of PL was decreased 4 nm after coating for QDs emitting at both 600 and 652 nm. The PL efficiency of the SiO(2)-coated is up to 40%, mainly determined by the initial PL efficiency of the underlying CdSe/Cd(x)Zn(1-x)S QDs.     

Photoluminescence and Raman scattering from catalytically grown Zn(x)Cd(1-x)Se alloy nanowires

Zn(x)Cd(1-x)Se alloy nanowires, with composition x = 0, 0.2, 0.5, 0.7, and 1, have been successfully synthesized by a chemical vapor deposition (CVD) method assisted with laser ablation. The as-synthesized alloy nanowires, 60-150 nm in diameter and several tens of micrometers in length, complied with a typical vapor-liquid-solid (VLS) growth mechanism. The Zn(x)Cd(1-x)Se nanowires are single crystalline revealed from high-resolution transmission electron microscopic (HRTEM) images, selected area electron diffraction (SAED) patterns, and X-ray diffraction (XRD) measurement. Compositions of the alloy nanowires can be adjusted by varying the precursor ratios of the laser ablated target and the CVD deposition temperature. Crystalline structures of the Zn(x)Cd(1-x)Se nanowires are hexagonal wurtzite at x = 0, 0.2, and 0.5 with the [0 1 -1 0] growth direction and zinc blende at x = 0.7 and 1 with the [1 -1 1] growth direction. Energy gaps of the Zn(x)Cd(1-x)Se nanowires, determined from micro-photoluminescence (PL) measurements, change nonlinearly as a quadratic function of x with a bowing parameter of approximately 0.45 eV. Strong PL from the Zn(x)Cd(1-x)Se nanowires can be tuned from red (712 nm) to blue (463 nm) with x varying from 0 to 1 and has demonstrated that the alloy nanowires have potential applications in optical and sensory nanotechnology. Micro-Raman shifts of the longitudinal optical (LO) phonon mode observed in the Zn(x)Cd(1-x)Se nanowires show a one-mode behavior pattern following the prediction of a modified random element isodisplacement (MREI) model.     

Effects of thermal annealing on the structural and optical properties of Mg(x)Zn(1-x)O nanocrystals

Mg(x)Zn(1-x)O ternary alloy nanocrystals with hexagonal wurtzite structures were fabricated by using the sol-gel method. X-ray diffraction patterns, UV-vis absorption spectra, and photoluminescence spectra were used to characterize the structural and optical properties of the nanocrystals. For as-prepared nanocrystals, the band gap increases with increasing Mg content. Weak excitonic emission with strong deep-level emission related to oxygen vacancy and interface defects is observed in the photoluminescence spectra at room temperature. Thermal annealing in oxygen was used to decrease the number of defects and to improve the quality of the nanocrystals. In terms of XRD results, the grain sizes of nanocrystals increase with increasing annealing temperature and the lattice constants of alloy are smaller than those of pure ZnO. The band gap becomes narrower with increasing annealing temperature. For Mg(x)Zn(1-x)O nanocrystals (x=0.03-0.15) annealed at temperatures ranging from 500 to 1000 degrees C, intense near-band-edge (NBE) emissions and weak deep-level (DL) emissions are observed. Consequently, the quality of Mg(x)Zn(1-x)O nanocrystals can be improved by thermal annealing.     

Continuous synthesis of CdSe(x)Te(1-x) nanocrystals: chemical composition gradient and single-step capping

Thermosensitive poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymer, Pluronic F68, containing a hydrophobic unit, oligo-(lactic acid)(oligo-LA) or oligo-caprolactone (oligo-CL), 2-META and RGD as side groups was successfully synthesized and characterized by (1)H NMR, FTIR, and elemental analysis. Their aqueous solution displayed special gel-sol-gel phase transition behavior with increasing temperature from 10 to 70°C, when the polymer concentration was above critical micelle concentration (CMC). The gel-sol phase diagram was investigated using tube inversion method, rheological measurement, and dynamic light scattering. Based on these results, the gelation properties of modified F68 were affected by several factors such as the composition of the substituents, chain length of oligo L-LA or oligo ε-CL, and the concentration of the polymer solutions. The unique phase transition behavior with temperature was observed by modified F68 triblock copolymer, composed of the PPO blocks core and the PEO blocks shell in aqueous solution. This phenomenon was elucidated using (1)H NMR data; the alteration of hydrophobic interaction and chain mobility led to the formation of transparent gel, coexistence of gel-sol, and opaque gel. These hydrogels may be useful in drug delivery and tissue engineering.     

Photodegradation of toluene over TiO(2-x)N(x) under visible light irradiation

We report the photooxidation of toluene over nitrogen doped TiO(2) (TiO(2-x)N(x)) under visible light irradiation. The photocatalytic oxidation of toluene in air over TiO(2-x)N(x) powders was studied using diffuse reflectance Fourier transform infrared spectroscopy (DRIFTS), gas chromatography (GC), ion chromatography (IC), and gas chromatography mass spectrometry (GC-MS), focusing on the photocatalytic decomposition processes of toluene. Results obtained indicate that toluene, weakly adsorbed on the catalyst surface, is initially photooxidized to benzaldehyde which adsorbs onto the TiO(2-x)N(x) surface more strongly, leading to the formation of ring-opening products such as carboxylic acids and aldehydes. No gaseous intermediates were detected during the photooxidation. Major intermediates adsorbed at the catalyst surface were oxalic acid, (COOH)(2), acetic acid, CH(3)COOH, formic acid, HCOOH, and pyruvic acid, CH(3)COCOOH, whereas more complicated carboxylic species, including propionic acid, CH(3)CH(2)COOH, isovaleric acid, (CH(3))(2)CHCH(2)COOH, and succinic acid, (CH(2)COOH)(2), were also found in the early stage of the photooxidation. These intermediate products were gradually photodegraded to CO(2) and H(2)O under visible light irradiation.     

Compositionally tunable Cu2ZnSn(S(1-x)Se(x))4 nanocrystals: probing the effect of Se-inclusion in mixed chalcogenide thin films

Nanocrystals of multicomponent chalcogenides, such as Cu(2)ZnSnS(4) (CZTS), are potential building blocks for low-cost thin-film photovoltaics (PVs). CZTS PV devices with modest efficiencies have been realized through postdeposition annealing at high temperatures in Se vapor. However, little is known about the precise role of Se in the CZTS system. We report the direct solution-phase synthesis and characterization of Cu(2)ZnSn(S(1-x)Se(x))(4) nanocrystals (0 ≤ x ≤ 1) with the aim of probing the role of Se incorporation into CZTS. Our results indicate that increasing the amount of Se increases the lattice parameters, slightly decreases the band gap, and most importantly increases the electrical conductivity of the nanocrystals without a need for annealing.     

Electrochemical formation and composition analysis of Zn x Cd1-x Se solid solutions

The direct growth of ZnSe–CdSe solid solution onto metallic cathodes by electrodeposition from acidic aqueous sulphate solutions is described. The plating process is studied by simple voltammetry, while the structure and composition of the electrolytic deposits are investigated by X-ray diffraction. The experimental d-spacing values of the as-grown mixed lattice are compared to data from reference Zn _x Cd_1-x Se pellets of standard composition, produced by a sintering method. The findings are supplemented with energy-dispersive X-ray (EDX) elemental analysis. Thereupon, the variation of the mole fraction x in Zn _x Cd_1-x Se, and the solid phase constitution of the electrodeposits are determined and correlated to the electrochemical conditions of growth. The resulting films contain admixtures of CdSe compound and metallic Cd.     

Ab Initio simulations of nonstoichiometric Cd(x)Te(1-x) liquids

We present ab initio molecular-dynamics simulations for Cd(x)Te(1-x) liquids where the composition is nonstoichiometric. The simulations are performed following Born-Oppenheimer molecular dynamics. The required forces are obtained from a solution of the Kohn-Sham equation using ab initio pseudopotentials. We consider stoichiometries of the form: Cd(x)Te(1-x), where x=0.2, 0.4, 0.6, and 0.8. For each composition of the melt, we consider a range of temperatures near the experimentally determined liquid temperatures. We examine the microstructural properties of the melt, the viscosity, and self-diffusion properties of the liquid as a function of the stoichiometry and temperature. We also perform an analysis of the distribution of the electronic density of states in these liquids. We find that structural changes in the local order, experimentally predicted to occur when the concentration of Cd is increased, are closely related to changes in the electronic properties of the melt.     

Alloyed (ZnS)(x)(Cu2SnS3)(1-x) and (CuInS2)(x)(Cu2SnS3)(1-x) nanocrystals with arbitrary composition and broad tunable band gaps

Cu(2)SnS(3) nanocrystals with metastable zincblende and wurtzite structures have been successfully synthesized for the first time. Alloyed (ZnS)(x)(Cu(2)SnS(3))(1-x) and (CuInS(2))(x)(Cu(2)SnS(3))(1-x) nanocrystals with arbitrary composition (0 ≤x≤ 1) and ultra-broad tunable band gaps (3.63 to 0.94 eV) were obtained.     

Thermoelectric properties of Yb(x)Eu(1-x)Cd2Sb2

The thermoelectric performance of EuCd(2)Sb(2) and YbCd(2)Sb(2) was improved by mixed cation occupation. The composition, structure, and thermoelectric properties of Yb(x)Eu(1-x)Cd(2)Sb(2) (x=0, 0.5, 0.75, and 1) have been investigated. Polycrystalline samples are prepared by direct reaction of the elements. Thermoelectric properties were investigated after densification of the materials by spark plasma sintering. Yb(x)Eu(1-x)Cd(2)Sb(2) crystallizes in the P3m1 space group. The lattice parameters increase with the europium content. These materials show low electrical resistivity, high Seebeck coefficient, and low thermal conductivity together with high carrier concentration and high carrier mobility. ZT values of 0.88 and 0.97 are obtained for Yb(0.5)Eu(0.5)Cd(2)Sb(2) and Yb(0.75)Eu(0.25)Cd(2)Sb(2) at 650 K, respectively.     

InAs(x)Sb(1-x) alloy nanocrystals for use in the near infrared

InAs(x)Sb(1-x) alloy nanocrystals for the near-infrared, which have quite a monodisperse crystalline structure of 2.5-3.0 nm and are of a zinc blend structure, are developed.