半化学法制备PMW-PNN-PT粉体的反应机理研究

The mechanism of perovskite 0.1Pb(Mg_1/2W_1/2)O₃-0.6Pb(Ni_1/3Nb_2/3)O₃-0.3PbTiO₃ (abbreviated PMW-PNN-PT) phase formation by Semichemical Method has been studied. The precursors were prepared by adding aqueous solution of Mg(Ac)₂ and Ni(AC)₂ rather than solid MgO and NiO to the alcoholic slurry of PbO, WO₃, Nb₂O₅ and TiO₂. The TG-DTG and DSC of the precursors and XRD analysis of the powders at various calcination temperature showed that the mechanism of this method was different from that of the conventional mixed oxide method. The aqueous Mg(Ac)₂ and Ni(Ac)₂ reacted with PbO to form basic lead acetate, basic magnesium acetate and basic nickel acetate and so on. With the increase of calcination temperature these basic salt decomposed to form nascent PbO, MgO and NiO, which improved the reactivity and distribution of PbO, MgO and NiO. In addition, the formation of PbWO₄ and pyrochlore phase Pb₃Nb₂O₈ in the process was in favor of the pervoskite PMW-PNN-PT phase formation. At the calcining temperature of 850 ℃, the perovskite phase reached 98%.     

溶胶-凝胶法制备掺锰钛酸钡纳米粉体及其陶瓷

The Mn-doped barium titanate nanosized powders and ceramics were prepared via the sol-gel process. The powders and ceramics were characterized by XRD， SEM and TEM. The dielectric properties of the ceramics were also measured. The influences of calcination temperature and Mn concentration on the microstructure， dielectric properties and phase composition of BaTiO₃ nano-powders and ceramics were discussed. The results indicated that the BaTiO₃-based powders doped with 1.0mol% Mn were mainly in cubic BaTiO₃ phase， but the tetragonal phase became more evident when the calcination temperature increased. After sintering， Mn-doped ceramics were mainly composed of cubic BaTiO₃. Specially， a new phase of hexagonal crystal BaTiO₃ and BaMnO₃ existed in the ceramics doped with 5.0mol% Mn and the ceramic grains were in ‘clintheriform’. The structure of ‘clintheriform’ led to the poor densification of ceramics， reducing the dielectric constant obviously. The dielectric constants of BaTiO₃ ceramics first increased and then decreased as the Mn concentration increased. The room temperature dielectric constant was 2 290 and the lowest dielectric loss was 0.004 when the Mn concentration was 0.5mol%.     

新铌酸盐Ba5NdTi3Nb7O30的合成与介电性能

The New Niobate Ba₅NdTi₃Nb₇O₃₀ was synthesized by solid state reaction at 1250℃ for 48h. The crystal structure and dielectric properties of Ba₅NdTi₃Nb₇O₃₀ were determined by X-ray powder diffraction and dielectric measurements. The results show that Ba₅NdTi₃Nb₇O₃₀ belongs to ferroelectric phase of tetragonal tungsten bronze structure at room temperature with unit cell parameters: a=1.24424(4)nm, c=0.39476(2)nm, calculated density 5.719g·cm^-3. Ba₅NdTi₃Nb₇O₃₀ belongs to relaxor ferroelectrics. The phase transition temperature (T_c) of Ba₅NdTi₃Nb₇O₃₀ from ferroelectric to paraelectric is found to shift toward higher temperature side at higher fre-quency, and T_c is 90℃ at 1kHz. At room temperature, the dielectric constant (ε_r) and dielectric loss of Ba₅NdTi₃Nb₇O₃₀ decrease with the increase of frequency, and Ba₅NdTi₃Nb₇O₃₀ ceramic have high dielectric constant 489 at 1kHz.     

类钙钛矿新铌酸盐Ba6LaTi3Nb3O21的合成、结构与介电特性

A New Niobate Ba₆LaTi₃Nb₃O₂₁ was synthesized by high temperature solid state reaction in the BaO-La₂O₃-TiO₂-Nb₂O₅ system. The chemical compositions, crystal structure, microstructure, density and melting point of the new compound were characterized by EPMA, XRD, DTA and so on. Ba₆LaTi₃Nb₃O₂₁ crystallizes the rhombohedral system with unit cell parameters a=0.57388(2) nm, c=4.928 3(3) nm, and space group R3m, Z=3. The structure may be described as six (Nb,Ti)O₆ octahedra corner-sharing along c-axis to form perovskite layer connected by Ba atoms. The Ba₆LaTi₃Nb₃O₂₁ ceramics exhibits high dielectric of 74.1, low dielectric loss of 4.7×10^-4 and small temperature coefficient of dielectric constant of -69 ppm·K^-1 at 1 MHz due to its close structure and relative high dielectric polarizabilities of Ba²⁺, La³⁺, Ti⁴⁺ and Nb⁴⁺. Ba₆LaTi₃Nb₃O₂₁ might be a suitable candidate of high ε_r microwave dielectric ceramics.     

Nd2O3添加量对BaTiO3陶瓷介电性能的影响

BaTiO₃ ceramics doped with Nd₂O₃(the additive content was respectively 0.001,0.002,0.003,0.005,0.01,0.03mol)were prepared by Sol-Gel method. Effects of Nd₂O₃ contents on the dielectric constant (ε), the dielectric loss (tanδ) ,the Curie-temperature (T_C) and the resistivity (ρ) of BaTiO₃ ceramic were studied. When Nd₂O₃ content was 0.001mol and 0.002mol, the dielectric constant was increased obviously, but the dielectric loss was also increased. When Nd₂O₃ content was 0.003mol, the dielectric constant was increased, and the dielectric loss was decreased, which was suitable for application in condenser. The resistivity was decreased obviously with the increasing of Nd₂O₃ contents, the resistivity was the smallest when Nd₂O₃ content was 0.001mol. The Curie-temperature was also decreased with the increasing of Nd₂O₃ contents.     

介稳态氧化钨超微粉体的水热合成与光致变色性质研究

Under hydrothermal conditions, the superfine powders of cubic pyrochlore-type of tungsten oxide and hexagonal tungsten bronze were obtained by using Na₂WO₄·2H₂O as the starting material. The products were characterized by XRD, TG, IR, UV and EPMA, respectively. The effects of the pH value, the acid concentration, reaction temperature and time on the structure and particle size of products were investigated in detail. The conditions for the preparation of superfine powders of tungsten oxide were optimized. The pH 2.5～4.5 of the reaction system led to the formation of a pyrochlore phase and pH 0.5～2.0 gave the hexagonal tungsten bronze structure. The photochromism property of the hexagonal tungsten bronze was studied. The results show that pyrochlore and bronze phases are decomposed at 300 ℃ and 450 ℃, respectively. With the increasing of temperature, the structure of the two oxides changes. The pyrochlore-type powder changes completely into triclinic Na₂W₄O₁₃ around 500 ℃, while the bronze phase into a mixture of Na₂W₆O₁₉ and triclinic WO₃ at 550 ℃. The powder of the hexagonal tungsten bronze showed better photochromism property.     

钨青铜结构Ba6Zn0.67M9.33O30(M=Nb,Ta)的合成与介电特性

Two compounds Ba₆Zn_0.67M_9.33O₃ and Ba₆Zn_0.67M_9.33O₃₀ with tungsten bronze structure were synthesized in the BaO-ZnO-Nb₂O₅/Ta₂O₅ systems by the conventional high temperature solid-state reaction.The structure and dielectric properties of Ba₆Zn_0.67M_9.33O₃ and Ba₆Zn_0.67M_9.33O₃₀ were determined by X-ray powder diffraction,scanning electron microscope and dielectric measurements.The results show that Ba₆Zn_0.67M_9.33O₃₀ belongs to paraelectric phase of fully filled tetragonal tungsten bronze structure at room temperature with unit cell parameters a:1.26256(4) nm, c:0.39698(2) nm. The room temperature dielectric constant (ε) of Ba₆Zn_0.67M_9.33O₃₀ ceramic reached 108 combined with a low dielectric loss of 0.005 at 1 MHz. While Ba₆Zn_0.67M_9.33O₃ belongs to fully filled tetragonal tungsten bronze structure at room temperature with the unit cell parameters a:1.25940 (3) nm, c=0.40008(2) nm. Ba₆Zn_0.67M_9.33O₃₀ ceramic shows significant relaxor behaviors, and the phase transition from ferroelectric to paraelectric occurred at 55℃ (at 1 MHz). The room temperature dielectric constant (ε) of ceramic reached 570 at 1 MHz.     

Ba1-xSrxTi1-yMyO3固溶体的湿化学法合成与介电特性

A series of Ba_1-xSr_xTi_1-yM_yO₃ (M=Zr,Sn, 0≤ x≤ 0.5,0≤ y≤ 0.3) solid solutions were synthesized by chemical method at below 100℃ . XRD and cell parameters component figures of the series of the solid solutions powder demonstrated that the compounds are mutually miscible in the solid solutions. The particls size is about 70nm with spherical shape and uniform distribution. The result of preparing ceramics showed that after adulterating with Sr²⁺ and Zr⁴⁺ or Sn⁴⁺ in pure BaTiO₃ phase, the dielectric constant increased eight times while the dielectric loss decreased three times at room temperature.     

溶胶凝胶法制备Nd2O3改性钛酸钡陶瓷的研究

The technological condition for the preparation of BaTiO₃ ceramics doped with Nd₂O₃ by Sol-Gel was deter-mined through orthogonal experiment. When n_Ba(Ac)2∶n_Ti(OC4H9)4∶n_Nd2O3∶n_{CH3(CH2)2CH2OH}∶n_H2O=1.00∶1.00∶0.003∶7.30∶37.04, pH=3.5,T=25℃,the light-yellow-transparent-stable solution and thorough transparent gel was generat-ed, the transforming time of solution to gel was 25h. The crystal structure and particle size of BaTiO₃ ceramics doped with Nd₂O₃ were studied by SEM and X-ray respectively, the type of the crystal was tetragonal, the particle size was about 24.7nm. The dielectric constant (ε) and dielectric loss (tanδ) of BaTiO₃ ceramics doped with Nd₂O₃ were determined between 10⁴～10⁶Hz, and the results showed that the dielectric constant was increased obviously, the dielectric loss was decreased clear and the resistivity (ρ_V) was also decreased noticeably.     

微量吸附量热研究CuO/γ-Al2O3催化剂的表面酸碱性质

The γ-Al₂O₃ supported CuO samples were studied. XRD results showed that the loading and calcination temperature affected the surface structure. For example， CuO crystallite appeared at the CuO loading of 7% (about 0.82mmol/100m²) on the support. Both CuO crystallite and CuAl₂O₄ spinel were present when the CuO/γ-Al₂O₃ sample was calcined at the same temperature (400℃). Microcalorimetric adsorption of CO₂ and NH₃ revealed that the strength of both the acidity and basicity decreased with the increase of CuO loading for the CuO/γ-Al₂O₃ sample. The increase of calcination temperature further decreased the basicity while the acidity was not affected.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.