Accelerated ageing and degradation in poly-l-lactide/hydroxyapatite nanocomposites

Dry, compression molded films of medical grade poly-l-lactide (PLLA) showed a marked reduction in tensile strength and strain after accelerated ageing in aqueous NaOH at 50 °C, accompanied by mass loss, surface erosion, increased hydrophilicity and, in the case of the initially amorphous films, cold crystallization owing to the plasticizing effect of the ageing medium. Addition of well dispersed nanosized hydroxyapatite (nHA) particles resulted in increases in the rate of mass loss during ageing, identified with accelerated degradation at the matrix/particle interfaces. However, the associated decreases in tensile strength and strain to fail with ageing time were far less marked in the presence of the nHA than in the unmodified films. This implied that nHA acts as an effective toughener of the bulk material, consistent with TEM observations of the deformed films, which indicated failure of the particle-matrix interfaces to promote plastic deformation of the PLLA.     

Electrospun poly(l-lactide)-grafted hydroxyapatite/poly(l-lactide) nanocomposite fibers

Composite fibers composed of poly(l-lactide)-grafted hydroxyapatite (PLA-g-HAP) nanoparticles and polylactide (PLA) matrix were prepared by electro-spinning. Environmental scanning electron microscope (ESEM) and transmission electron microscopy (TEM) were employed to investigate the morphology of the composite fibers and the distribution of PLA-g-HAP nanoparticles in the fibers, respectively. At a low content (∼4 wt%) of PLA-g-HAP, the nanoparticles dispersed uniformly in the fibers and the composite fibrous mats exhibited higher strength properties, compared with the pristine PLA fiber mats and the simple hydroxyapatite/PLA blend fiber mats. But when the content of PLA-g-HAP further increased, the nanoparticles began to aggregate, which resulted in the deterioration of the mechanical properties of the composite fiber mats. The degradation behaviors of the composite fiber mats were closely related to the content of PLA-g-HAP. At a low PLA-g-HAP content, degradation may be delayed due to the reduction of autocatalytic degradation of PLA. When PLA-g-HAP content was high, degradation rate increased because of the enhanced wettability of the composite fibers and the escape of the nanoparticles from fiber surfaces during incubation.     

Poly l-lactide-layered double hydroxide nanocomposites via in situ polymerization of l-lactide

The use of clay nanofillers offers a potential route to improved barrier properties in polylactide films. Magnesium-aluminium layered double hydroxides (LDHs) are interesting in this respect and we therefore explored synthesis of PLA-LDH nanocomposites by ring-opening polymerization. This method is attractive because it should ensure good dispersion of LDH in the polymer. The effect of adding either LDH carbonate (LDH-CO₃) or laurate-modified LDH (LDH-C₁₂) was investigated. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy revealed that exfoliated nanocomposites were obtained when using LDH-C₁₂ but that LDH-CO₃ gave a partly phase-separated morphology. Thermogravimetric analysis showed that PLA-LDH combinations exhibited higher degradation onset temperatures and differential scanning calorimetry confirmed that LDHs can act as nucleating agents. However, PLA molecular weight was significantly reduced when in-situ polymerization was conducted in the presence of the LDHs and we suggest that chain termination via LDH surface hydroxyl groups and/or metal-catalyzed degradation could be responsible.     

Nanostructure vs. microstructure: Morphological and thermomechanical characterization of poly(l-lactic acid)/layered silicate hybrids

Nano- and micro-composites of poly(l-lactic acid) (PLLA) with various loadings of natural and hexadecylamine-modified montmorillonite were prepared by the solvent casting method to study the effect of nanostructure on the thermomechanical properties of the hybrid materials. The changes on structure and surface of montmorillonite, induced by the ion-exchange modification process, were characterized by X-ray diffraction (XRD) analysis and zeta-potential determination, while the morphology of the hybrids and the dispersion of the clay into the polymer matrix were examined by XRD, transmission electron microscopy and atomic force microscopy. The results showed that, although at low clay content exfoliation dominates, for filler loadings greater than 5 wt% both exfoliation and intercalation of the clay filler are observed. Thermal degradation studies of the materials produced using thermogravimetry revealed the introduction of a small amount of organo-modified silicate significantly improves their thermal stability. Differential scanning calorimetry showed the thermal behavior of the polymer matrix strongly depends on the nature and content of the silicate filler. Scanning electron microscopy of the deformed surfaces affirmed a different deformation process mechanism between the two types of composites.     

Effect of layered double hydroxides on the thermal degradation behavior of biodegradable poly(l-lactide) nanocomposites

This study elucidates the thermal degradation behavior of biodegradable poly(l-lactide) (PLLA)/layered double hydroxide (LDH) nanocomposites was explored using thermogravimetric analysis (TGA) and pyrolysis-gas chromatography/mass spectroscopy (Py-GC/MS) in an inert atmosphere. PLLA/LDH nanocomposites were fabricated using PLLA and organically-modified magnesium/aluminum layered double hydroxide (P-LDH) in tetrahydrofuran solution. According to the TGA results, the thermal stability of PLLA/P-LDH nanocomposites was significantly lower than that of pure PLLA matrix, perhaps because P-LDH provides thermal acceleration of the degradation of the underlying polymer from the heat source. The identification of the thermal degradation products by Py-GC/MS evidently shows that introducing P-LDH into PLLA leads to a remarkable change during the thermal degradation process. The main reaction route of neat PLLA was through inter- and intra-transesterification to generate lactides and oligomer. The primary volatile products obtained from PLLA/P-LDH nanocomposites were lactides regardless of the temperature of degradation. These results suggest that the thermal degradation behavior of PLLA/P-LDH nanocomposites is governed by the preferential formation of lactide by the unzipping depolymerization reaction, which is catalyzed by Mg and Al components in P-LDH.     

Surface properties and enzymatic degradation of end-capped poly(l-lactide)

Surface properties and enzymatic degradation of poly(l-lactide) (PLLA) end-capped with hydrophobic dodecyl and dodecanoyl groups were investigated by means of advancing contact angle (θ_a) measurement, quartz crystal microbalance (QCM) and atomic force microscopy (AFM). The θ_a values of end-capped PLLA films were larger than those of non-end-capped PLLA films, suggesting that the hydrophobic dodecyl and dodecanoyl groups were segregated on the film surface. The weight changes of end-capped PLLA thin films during enzymatic degradation in the presence of proteinase K were monitored by using a QCM technique. The relatively fast weight loss of PLLA film occurred during first few hours of degradation, followed by a decrease in the erosion rate. The erosion rate of PLLA films at the initial stage of degradation was dependent on the chain-end structure of PLLA molecules, and the value decreased with an increase in the amount of hydrophobic functional groups. The surface morphologies of PLLA thin films before and after degradation were characterized by AFM. After the enzymatic degradation, the surface of non-end-capped PLLA films was blemished homogeneously. In contrast, the end-capped PLLA thin films were degraded heterogeneously by the enzyme, and many hollows were formed on the film surface. From these results, it has been concluded that the introduction of hydrophobic functional groups at the chain-ends of PLLA molecules depressed the erosion rate at the initial stage of enzymatic degradation.     

Preparation and characterization of biodegradable poly(l-lactide)/chitosan blends

In order to improve the properties of chitosan and obtain new fully biodegradable materials, blends of poly(l-lactide) (PLLA) and chitosan with different compositions were prepared by precipitating out PLLA/chitosan from acetic acid-DMSO mixtures with acetone. The blends were characterized by Fourier transform infrared analysis (FTIR), X-ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), ¹³C solid-state NMR and Wide-angle X-ray diffraction (WAXD). FTIR and XPS results showed that intermolecular hydrogen bonds existed between two components in the blends, and the hydrogen bonds were mainly between carbonyls of PLLA and amino groups of chitosan. The melting temperatures, cold crystallization temperatures and crystallinity of the PLLA component decreased with the increase in chitosan content. Blending chitosan with PLLA suppressed the crystallization of the PLLA component. Although the crystal structure of PLLA component was not changed, the crystallization of the blends was affected because of the existence of hydrogen bonds between two components, which was proved by WAXD results.     

Phase behavior of biodegradable amphiphilic poly(l,l-lactide)-b-poly(ethylene glycol)-b-poly(l,l-lactide)

This study describes the miscibility phase behavior in two series of biodegradable triblock copolymers, poly(l-lactide)-block-poly(ethylene glycol)-block-poly(l-lactide) (PLLA-PEG-PLLA), prepared from two di-hydroxy-terminated PEG prepolymers (M_n = 4000 or 600 g mol⁻¹) with different lengths of poly(l-lactide) segments (polymerization degree, DP = 1.2-145.6). The prepared block copolymers presented wide range of molecular weights (800-25,000 g mol⁻¹) and compositions (16-80 wt.% of PEG). The copolymer multiphases coexistance and interaction were evaluated by DSC and TGA. The copolymers presented a dual stage thermal degradation and decreased thermal stability compared to PEG homopolymers. In addition, DSC analyses allowed the observation of multiphase separation; the melting temperature, T_m, of PLLA and PEG phases depended on the relative segment lengths and the only observed glass transition temperature (T_g) in copolymers indicated miscibility in the amorphous phase.     

Influence of crystal polymorphism on mechanical and barrier properties of poly(l-lactic acid)

The effect of crystal polymorphism on barrier and mechanical properties of PLLA is detailed in this contribution. PLLA films containing different amounts of α and α′ crystal forms were prepared by annealing quenched PLLA at different temperatures. The polymorphic structure of the films was analyzed by X-ray diffraction. Mechanical properties and permeability to water vapor were investigated as a function of degree of crystallinity (w_C) and related to crystal polymorphism developed during annealing. The polymorphic structure of PLLA significantly affects mechanical and barrier properties. The α crystal modification provides a better barrier to water vapor and a higher Young’s modulus, compared to films containing the α′ modification, but a lower elongation at break. The varied barrier and mechanical properties were correlated to the different packing of PLLA chains in the two analyzed polymorphs. The conformational disorder of the α′ form makes this structure a mesophase (condis crystal), with remarkable effects on material properties.     

Racemization behavior of l,l-lactide during heating

To control the depolymerization process of poly(l-lactic acid) into l,l-lactide for feedstock recycling, the racemization of l,l-lactide as a post-depolymerization reaction was investigated. In the absence of a catalyst, the conversion to meso-lactide increased with increase in the heating temperature and time at a higher rate than the conversion into oligomers. The resulting high composition of meso-lactide suggests that the direct racemization of l,l-lactide had occurred in addition to the known racemization mechanism that occurs on the oligomer chains. In the presence of MgO, the oligomerization rapidly proceeded to reach an equilibrium state between monomers and oligomers. The equilibrium among l,l-, meso-, and d,d-lactides was found to be a convergent composition ratio l,l-:meso-:d,d-lactides = 1:1.22:0.99 (wt/wt/wt) after 120 min at 300 °C. This composition ratio also indicates that in addition to the known racemization reaction on the oligomer chains, direct racemization among the lactides is also a frequent occurrence.     

Cooperative rearranging region size determination by temperature modulated DSC in semi-crystalline poly(l-lactide acid)

Thermal analyzes have been performed on poly(l-lactide acid) (PLLA) annealed at 353 K for different durations in order to obtain a crystallinity degree varying between 0% and 42%. From temperature modulated differential scanning calorimetry investigations, we have calculated the average volume of a cooperative rearranging region (CRR) at the glass transition temperature , according to the method developed by Donth. The results show that the presence of crystalline phase in PLLA amorphous matrix implies modifications on structural relaxation phenomena, in particular on the average number of monomer units relaxing in the same time at the glass transition temperature.     

Accelerated hydrolytic degradation of Poly(l-lactide)/Poly(d-lactide) stereocomplex up to late stage

Poly(l-lactide) (PLLA)/poly(d-lactide) (PDLA) blend specimens containing only stereocomplex as crystalline species, together with those of pure PLLA and PDLA specimens, were prepared by solution crystallization using acetonitrile as the solvent. Their accelerated hydrolytic degradation was carried out in phosphate-buffered solution at elevated temperatures of 70-97 °C up to the late stage. During hydrolytic degradation, the stereocomplex crystalline residues were first traced by gel permeation chromatography. Similar to the hydrolytic degradation of pure PLLA and PDLA specimens, the hydrolytic degradation of stereocomplexed PLLA/PDLA blend specimens slowed down at the late stage when most of the amorphous chains were removed and crystalline resides were formed and degraded. The estimated activation energy for hydrolytic degradation of stereocomplex crystalline residues (97.3 kJ mol⁻¹) is significantly higher than 75.2 kJ mol⁻¹ reported for α-form of PLLA crystalline residues. This indicates that the stereocomplex crystalline residues showed the higher hydrolysis resistance compared to that of α-form of PLLA crystalline residues.     

Hydrolytic degradation behavior of poly(l-lactide)/SiO2 composites

In this work, different contents of nano-silica (SiO₂) particles were introduced into poly(l-lactide) (PLLA) to prepare PLLA/SiO₂ composites though a two-step compounding method, i.e. solution compounding (preparing master batch) and subsequent melt compounding (master batch dilution). The dispersion of SiO₂ was characterized using scanning electron microscope (SEM). The hydrophilicity of the material was evaluated by measuring the contact angle of water on the sample surface. The hydrolytic degradation measurements of the nanocomposites were carried out in alkaline solution at two different temperatures, i.e. 37 and 55 °C. Subsequently, microstructure evolution of PLLA matrix during the hydrolytic degradation process was systematically investigated using wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), and Fourier transform infrared spectroscopy (FTIR). The results showed that SiO₂ had good dispersion in the PLLA matrix. Largely enhanced hydrolytic degradation ability was achieved for PLLA/SiO₂ composites. Increasing the content of SiO₂ or enhancing the hydrolytic degradation temperature accelerated the hydrolytic degradation of PLLA matrix. Further results showed that SiO₂ promoted the reorganization of microstructure of PLLLA matrix during the hydrolytic degradation process.     

Thermal and electrical properties of poly(l-lactide)-graft-multiwalled carbon nanotube composites

The dispersion of the nanometer-sized carbon nanotubes in a polymer matrix leads to a marked improvement in the properties of the polymer. This approach can also be applied to biodegradable synthetic aliphatic polyesters such as poly(l-lactide) (PLLA), which has received a great deal of attention due to environmental concerns. In this study, PLLA was melt compounded with multiwalled carbon nanotubes (MWCNTs). A high degree of dispersion of the MWCNTs in the composites was obtained by grafting PLLA onto the MWCNTs (PLLA-g-MWCNTs). After oxidizing the MWCNTs by treating them with strong acids, they were reacted with l-lactide to produce the PLLA-g-MWCNTs. The morphology of the composite was observed with scanning electron microscopy. The mechanical properties of the PLLA/PLLA-g-MWCNT composite were higher than those of the PLLA/MWCNT composite. The thermal stability of the composites was studied using thermogravimetric analysis and their activation energy during thermal degradation was determined using the Kissinger and Flynn-Wall-Ozawa methods. The activation energy of PLLA/PLLA-g-MWCNT was higher than that of PLLA/MWCNT, which indicates that the composite made with the PLLA-g-MWCNTs was more thermally stable than the composite made with the MWCNTs.     

Improvement in toughness of poly(l-lactide) (PLLA) through reactive blending with acrylonitrile-butadiene-styrene copolymer (ABS): Morphology and properties

Poly(l-lactide) (PLLA) was melt-blended with acrylonitrile-butadiene-styrene copolymer (ABS) with the aim of enhancing impact strength and elongation at break of PLLA, but not sacrificing its modulus and stiffness significantly. However, PLLA and ABS were found to be thermodynamically immiscible by simply melt blending and the formed blends show deteriorated mechanical properties. The reactive styrene/acrylonitrile/glycidyl methacrylate copolymer (SAN-GMA) by incorporating with ethyltriphenyl phosphonium bromide (ETPB) as the catalyst was used as the in situ compatibilizer for PLLA/ABS blends to improve the compatibility between PLLA and ABS. The reactive process during melt blending was investigated by Fourier transformed infra-red (FTIR). It showed that the epoxide group of SAN-GMA reacted with PLLA end groups under the mixing conditions and that the addition of ETPB accelerated the reaction. Phase structure and physical properties of the compatibilized blends were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), dynamic mechanical analysis (DMA), tensile tests and impact property measurements. It was found that the size of ABS domains in PLLA matrix is significantly decreased by addition of the reactive compatibilizer. The dynamic mechanical analysis revealed markedly shifted glass transition temperatures for both PLLA and ABS, indicating the improved compatibility between PLLA and ABS. The mechanical tests showed the compatibilized PLLA/ABS blends had a very nice stiffness-toughness balance, i.e., the improved impact strength and the elongation at break with a slightly loss in the modulus.     

Nanocomposites of poly(l-lactide) and surface-grafted TiO2 nanoparticles: Synthesis and characterization

A new method of surface modification of TiO₂ nanoparticles by surface-grafting l-lactic acid oligomer was developed. The surface-grafting reaction was evaluated by Fourier transformation infrared (FTIR) and thermal gravimetric analysis (TGA). The results showed that l-lactic acid oligomer could be easily grafted onto the TiO₂ nanoparticles surface in the presence of stannous octanoate and the highest amount of grafted polymer was about 8.5% in weight. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) results showed that grafted TiO₂ (g-TiO₂) in chloroform or PLLA matrix approximated to uniform, while unmodified TiO₂ nanoparticles tended to aggregate. The tensile strength of this material was greatly improved by the addition of g-TiO₂ nanoparticles in poly(l-lactide) (PLLA) matrix. The tensile strength of the g-TiO₂/PLLA nanocomposite containing 5 wt.% of g-TiO₂ was 72 MPa, which was 23.1% higher than that of pure PLLA. Even though the incorporation of the TiO₂ nanoparticles into PLLA led to the deterioration of its elongation at break, the g-TiO₂/PLLA nanocomposite also exhibited better ductility than that of TiO₂/PLLA nanocomposite.     

Biodegradable electrospun poly(l-lactide) fibers containing antibacterial silver nanoparticles

Biodegradable poly(l-lactide) (PLA) ultrafine fibers containing nanosilver particles were prepared via electrospinning. Morphology of the Ag/PLA fibers and distribution of the silver nanoparticles were characterized. The release of silver ions from the Ag/PLA fibers and their antibacterial activities were investigated. These fibers showed antibacterial activities (microorganism reduction) of 98.5% and 94.2% against Staphylococcus aureus and Escherichia coli, respectively, because of the presence of the silver nanoparticles.     

Synthesis of l-aminohomohistidine (l-Ahh)

A short synthesis of l-aminohomohistidine (l-Ahh), which starts from readily available δ-hydroxy-l-lysine is described. The embedding of the basic guanidino moiety in the aromatic imidazole lowers the basicity of the side chain to a pK_a of 8.3. It is proposed that l-Ahh may be employed as an arginine-mimetic in medicinal chemistry.     

Synthesis and biodegradability of l-lactide/glycidol copolymers

Random copolymers of l-lactide (LA) and glycidol (G) were systematically synthesized via ring-opening polymerization (ROP). It was found that thermal properties of copolymers were strongly dependent on polymer composition which was successively controllable by changing comonomer feed ratio. The effects of polymerization conditions as well as polymer compositions on polymer properties were thoroughly studied. The biodegradation and enzymatic hydrolysis of copolymers were also examined. It was found that the biodegradability by an activated sludge of L/G copolymers was strongly affected by both polymer composition and crystallinity whereas their hydrolyzability by proteinase K was merely influenced by polymer composition.     

Effect of type of peroxide on cross-linking of poly(l-lactide)

Poly(l-lactide) (PLLA) was cross-linked with various types of peroxides under constant mole ratios of peroxide-derived radicals to PLLA during reactive extrusion. Peroxides were classified into three groups according to their decomposition rates (Group I: fast, Group II: moderate and Group III: slow) and comparisons were performed within each group. Cross-linking behavior was readily understood in terms of free radical efficiency and hydrogen abstraction ability of radicals. In the case of Groups II and III, the weight-average molecular weight (M_w) of cross-linked PLLA increased with overall hydrogen abstraction ability, because slow decomposition caused uniform cross-linking in molten PLLA. In Group I, M_w and gel fraction were higher than other groups despite Group I's lower hydrogen abstraction ability, leading to the conclusion that peroxide decomposition localized in solid PLLA caused partial cross-linking because of rapid decomposition. Furthermore, the efficiency of peroxide-induced cross-linking was investigated using the Charlesby-Pinner equation.