Polystyrene/thermoplastic starch blends with different plasticizers

Conventional plastics has a large impact in increasing the environment’s pollution. That’s why the interest has turned towards novel partially and completely biodegradable polymers. In this work, blends of polystyrene and thermoplastic starch with glycerol and Buriti (Mauritia flexuosa L.) oil as plasticizers were prepared. Samples were analyzed using TG/DTG and DSC techniques. The TG results indicated that the blends with Buriti oil are thermally more stable than those with glycerol. The DSC analysis that Buriti oil provides a higher degree of plasticization of PS, compared to the blends plasticized using glycerol under the studied conditions.     

Effects of organoclays on morphology and thermal and rheological properties of polystyrene and poly(methyl methacrylate) blends

Morphology, thermal and rheological properties of polymer‐organoclay composites prepared by melt‐blending of polystyrene (PS), poly(methyl methacrylate) (PMMA), and PS/PMMA blends with Cloisite® organoclays were examined by transmission electron microscopy, small‐angle X‐ray scattering, secondary ion mass spectroscopy, differential scanning calorimetry, and rheological techniques. Organoclay particles were finely dispersed and predominantly delaminated in PMMA‐clay composites, whereas organoclays formed micrometer‐sized aggregates in PS‐clay composites. In PS/PMMA blends, the majority of clay particles was concentrated in the PMMA phase and in the interfacial region between PS and PMMA. Although incompatible PS/PMMA blends remained phase‐separated after being melt‐blended with organoclays, the addition of organoclays resulted in a drastic reduction in the average microdomain sizes (from 1–1.5 μm to ca. 300–500 nm), indicating that organoclays partially compatibilized the immiscible PS/PMMA blends. The effect of surfactant (di‐methyl di‐octadecyl‐ammonia chloride), used in the preparation of organoclays, on the PS/PMMA miscibility was also investigated. The free surfactant was more compatible with PMMA than with PS; the surfactant was concentrated in PMMA and in the interfacial region of the blends. The microdomain size reduction resulting from the addition of organoclays was definitely more significant than that caused by adding the same amount of free surfactant without clay. The effect of organoclays on the rheological properties was insignificant in all tested systems, suggesting weak interactions between the clay particles and the polymer matrix. In the PS system, PMMA, and organoclay the extent of clay exfoliation and the resultant properties are controlled by the compatibility between the polymer matrix and the surfactant rather than by interactions between the polymer and the clay surface. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 44–54, 2003     

Influence of extender oil composition on flowing property,thermal stability,and morphology of styrene‐b‐ethylene‐co‐butylene‐b‐styrene copolymer/polypropylene/oil blends

In this study, a series of styrene‐b‐ethylene‐co‐butylene‐b‐styrene copolymer (SEBS)/polypropylene (PP)/oil blends with different kinds of oil composition was developed through melt blending. The effect of oil with different composition and properties on its phase equilibrium and “redistribution” in multiphasic SEBS elastomer was systematically studied for the first time. Moreover, an integral influencing mechanism of oil composition on the structure and properties of SEBS/PP/oil blends was also put forward. The mineral oil was mainly distributed in ethylene/butylene (EB)/PP phase, which greatly enhanced the processing flowability of SEBS/PP/oil blends. With increasing oil C_N content, a redistribution of oil appeared and excess naphthenic oil (NO) entered the interphase of soft and hard phases. The dynamic mechanical thermal analysis (DMTA) analysis indicated that the polystyrene (PS) phase was plasticized, which also helped to improve the processing fluidity of blends. However, the plasticizing of physical cross‐linking point PS resulted in a decrease in mechanical strength and thermal stability. Small‐angle X‐ray scattering (SAXS) and transmission electron microscope (TEM) results showed that PS phase (45 nm to 55 nm) cylindrically distributed in EB/PP/oil matrix, the excess NO in the interphase enlarged the distance between PS phase and widen the escape channel for oil migration. At over 45% oil C_N content, the electron density difference between soft and hard phases reduced to the minimum, same as T_gPS, indicating a deeper plasticizing effect. The PS phase swelled and exhibited elastic behavior; thus, the force could be uniformly transferred between two phases. Importantly, a recover in strength and thermal stability was observed in O‐5 blend. This work significantly filled the gap of studies in oil‐extended thermoplastic elastomers (TPEs), exhibiting great theoretical guiding significance and application value.     

Effect of molecular interactions on the miscibility and structure of polymer blends

The effect of polymer-polymer interactions on the miscibility and macroscopic properties of PVC/PMMA, PVC/PS and PMMA/PS blends were studied in the entire composition range. The miscibility of the components was characterized by the Flory-Huggins interaction parameter or by quantities related to it. Thermal analysis, light transmittance measurements, and scanning electron microscopy were carried out on the blends and their mechanical properties were characterized by tensile tests. Interactions were analyzed by infrared spectroscopy and contact angle measurements. All three polymer pairs form heterogeneous blends, but the strength of molecular interactions is different in them, the highest is in PVC/PMMA system resulting in partial miscibility of the components and beneficial mechanical properties. The structure of these blends depends strongly on composition. A phase inversion can be observed between 0.5 and 0.6 PMMA content accompanied with a significant change in structure and properties. The PVC/PS and the PMMA/PS pairs are immiscible, though the results indicate the partial solubility of the components. The analysis of the surface characteristics of the components and the comparison of quantities derived from them with miscibility as well as with the macroscopic properties of blends revealed that blend properties cannot be predicted in this way, since they are affected by several factors.     

Impact modification of thermoplastics by methyl methacrylate and styrene-grafted natural rubber latexes

The preparation and characterization of polymer blends with structured natural rubber (NR)-based latex particles are presented. By a semicontinuous emulsion polymerization process, a natural rubber latex (prevulcanized or not) was coated with a shell of crosslinked polymethylmethacrylate (PMMA) or polystyrene (PS). Furthermore, core–shell latexes based on a natural rubber/crosslinked PS latex semi-interpenetrating network were synthesized in a batch process. These structured particles were incorporated as impact modifiers into a brittle polymer matrix using a Werner & Pfleiderer twin screw extruder. The mechanical properties of PS and PMMA blends with a series of the prepared latexes were investigated. In the case of PMMA blends, relatively simple core (NR)–shell (crosslinked PMMA) particles improved the mechanical properties of PMMA most effectively. An intermediate PS layer between the core and the shell or a natural rubber core with PS subinclusions allowed the E-modulus to be adjusted. The situation was different with the PS blends. Only core–shell particles based on NR-crosslinked PS latex semi-interpenetrating networks could effectively toughen PS. It appears that microdomains in the rubber phase allowed a modification of the crazing behavior. These inclusions were observed inside the NR particles by transmission electron microscopy. Transmission electron photomicrographs of PS and PMMA blends also revealed intact and well-dispersed particles. Scanning electron microscopy of fracture surfaces allowed us to distinguish PS blends reinforced with latex semi-interpenetrating network-based particles from blends with all other types of particles.     

Use of block copolymer-stabilized cadmium sulfide quantum dots as novel tracers for laser scanning confocal fluorescence imaging of blend morphology in polystyrene/poly(methyl methacrylate) films

This paper describes the first use of polymer-coated quantum dots (QDs) as fluorescent tracers for LSCFM imaging of phase morphology in polymer blends. Cadmium sulfide (CdS) QDs stabilized at the surface with a PS-b-PAA block copolymer are shown to be well dispersed via their polystyrene (PS) brush layer in the PS phase of solvent-cast 40/60 (w/w) PS/PMMA blends. The QDs are excluded from the PMMA phase, providing excellent fluorescence contrast for LSCFM imaging of the phase-separated blends. The presence of PS-b-PAA-stabilized QDs does not appear to affect the blend morphology, since the observed morphologies are the same when the percentage of QDs within the PS phase is varied from 10 to 50 wt %. These QD fluorescent tracers are used to characterize several aspects of blend morphology in solvent-cast 40/60 PS/PMMA blends containing PS homopolymer with either 100 (low molecular weight) or 1250 (high molecular weight) repeat units. In the PS(1250)/PMMA blends, a percolating distribution of PMMA droplets (2-25 mum) in a PS matrix is observed in the bulk, and a distinct inversion in the continuous phase is found near the glass substrate. In the PS(100)/PMMA blends, a "phase-in-phase" morphology is found, consisting of large PS domains (20-100 mum) dispersed in a PMMA continuous phase and small PMMA domains (1-2 mum) scattered throughout the larger PS droplets. The observed change in blend structure is attributed to a lower interfacial tension for the lower molecular weight PS.     

SiO_2纳米粒子对PMMA/PS共混物共连续相结构退火粗化过程的影响

考察了亲水性纳米SiO2粒子的加入对聚甲基丙烯酸甲酯/聚苯乙烯(PMMA/PS)共混体系的共连续相结构在静态高温退火时形态稳定性的影响,发现静态高温退火条件下,填充体系共连续组成范围变窄幅度较小、特征结构尺寸的粗化速率减慢.流变测试表明纳米SiO2粒子加入之后PMMA/PS共混体系的黏弹性显著提高,从而能减缓破坏构成共连续相结构的纤维断裂或回缩等松弛过程的速率,有效地抑制PMMA/PS共混体系的共连续相结构粗化进程,提高相结构的稳定性.根据现有的两种粗化理论的定性分析表明,在高填充量的共混体系中,加入纳米SiO2粒子导致共混体系的黏弹性的显著改变是影响PMMA/PS共混体系在静态高温退火时共连续相结构粗化速率的主要因素,相对而言界面张力的变化对共连续相结构在静态高温退火时的粗化速率影响则应该较小.     

Degradation and thermal properties of in situ compatibilized PS/POE blends

This paper reported the degradation behaviors and thermal properties of polystyrene (PS)/polyolefin elastomer (POE) blends with AlCl₃ as the catalyst of Friedel-Crafts alkylation reaction. Gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) were adopted to reveal the effects of in situ grafting reaction and degradation of blending compounds on the thermal properties of PS/POE blends. It was found that the changes in both catalyst content and blend composition influenced the competition between in situ grafting reaction and degradation, resulting in the complexity of the thermal properties of PS/POE/AlCl₃ blends.     

PMMA/PS纳米复合材料的制备及分散相稳定性研究

纳米复合材料具有许多优异的性能,但是由于纳米粒子常常很难以纳米尺寸均匀地分散在基体中,有时即使实现了纳米级分散,在后加工或应用过程中又会发生二次团聚,使得纳米材料的特性不能充分发挥．因此,要获得性能优异的纳米复合材料首先必须解决纳米材料在基体中的均匀、稳定分散问题．     

Blends of poly(carbonate) with poly(styrene) and poly(methylmethacrylate): phase morphology,mechanical, and thermal properties

This paper is concerned with the dependence of mechanical and thermal properties of heterogeneous blends of poly(carbonate) (PC) with poly(methyl-methacrylate) (PMMA) and with poly(styrene) (PS) on the concentration of the components. PS displays a very weak phase coupling in blends with PC, whereas PMMA is characterized by a strong coupling to PC. Experimental results as well as predictions based on composite theories are reported. The general finding is that mechanical properties, such as the tensile modulus and the dynamic shear modulus, as well as thermal properties, such as thermal expansion, are (i) only weakly affected by the occurrence of a phase inversion and of a continuous phase morphology, (ii) vary continuously with the concentration of the components, and (iii) are rather insensitive to the strength of the phase coupling. The theoretical predictions on the concentration—property relationship for these properties, based on a self-consistent approach, agree very well with those observed experimentally. The elongation at break as well as the yield stress, on the other hand, are strongly influenced by the nature of the phase coupling: a discontinuous variation of these properties with the composition is observed for PS/PC blends but not for PMMA/PC blends. The general conclusion is that a set of mechanical and thermal properties of heterogeneous blends can satisfactorily be predicted on the basis of rather simple composite theories.     

Development and characterization of reactive extruded PVC/polyacrylate blends

This paper describes a method to obtain polymer blends by the absorption of a liquid solution of monomer, initiator, and a crosslinking agent in suspension type porous poly(vinyl chloride) (PVC) particles, forming a dry blend. These PVC/monomer dry blends are reactively polymerized in a twin‐screw extruder to obtain the in situ polymerization in a melt state of various blends: PVC/poly(methyl methacrylate) (PVC/PMMA), PVC/poly(vinyl acetate) (PVC/PVAc), PVC/poly(butyl acrylate) (PVC/PBA) and PVC/poly(ethylhexyl acrylate) (PVC/PEHA). Physical PVC/PMMA blends were produced, and the properties of those blends are compared to reactive blends of similar compositions. Owing to the high polymerization temperature (180°C), the polymers formed in this reactive polymerization process have low molecular weight. These short polymer chains plasticize the PVC phase reducing the melt viscosity, glass transition and the static modulus. Reactive blends of PVC/PMMA and PVC/PVAc are more compatible than the reactive PVC/PBA and PVC/PEHA blends. Reactive PVC/PMMA and PVC/PVAc blends are transparent, form single phase morphology, have single glass transition temperature (T_g), and show mechanical properties that are not inferior than that of neat PVC. Reactive PVC/PBA and PVC/PEHA blends are incompatible and two discrete phases are observed in each blend. However, those blends exhibit single glass transition owing to low content of the dispersed phase particles, which is probably too low to be detected by dynamic mechanical thermal analysis (DMTA) as a separate T_g value. The reactive PVC/PEHA show exceptional high elongation at break (～90%) owing to energy absorption optimized at this dispersed particle size (0.2–0.8 µm). Copyright © 2005 John Wiley & Sons, Ltd.     

Photochemical aging of in situ polymerized blends of polystyrene and poly[acrylonitrile-g-(ethylene-co-propylene-co-diene)-g-styrene] (AES)

The influence of photochemical aging of in situ polymerized PS/AES blends on their mechanical properties has been studied. The PS/AES blends were subjected to photochemical aging for 168 h and 720 h. Tensile properties and Izod impact resistance of aged and non-aged samples were evaluated. The mechanical properties of the PS/AES blends are influenced by the polymerization temperature and blend composition and represent a balance between the toughness of EPDM and the stiffness of SAN in the PS matrix. Even though the impact resistance and strain at break of HIPS are higher than those of the PS/AES blends, after the aging period all PS/AES blends showed higher strain at break than HIPS. PS/AES blends present higher photochemical stability than HIPS.     

Characterization and modification of polymer blend films

Films of immiscible blends of (PS) and poly(methyl methacrylate) (PMMA) were characterized by contact-angle measurements with sessile drop and atomic force microscopy (AFM). These blends showed a linear dependence of the contact angles on the composition, as predicted by Cassie's equation for ideal surfaces. The surface structure investigated by AFM showed low roughness and phase-separation features. The ratio between the drop radius and the roughness amounted to the order of 10⁴–10⁵. This magnitude seemed to be sufficient to put the PS/PMMA films close to ideality. Upon sulfonation, the wettability and the microscopic surface roughness of the PS/PMMA blends increased. The treatment with sulfuric acid yielded sulfonated PS domains on the surface, causing an increase in the surface wettability. The SO₃ ⁻ groups were evidenced by X-ray photoelectron spectroscopy. The sulfonation of the PS/PMMA blends enables the formation of multiphase surfaces with hydrophobic, charged and polar domains. Received: 11 December 2000 Accepted: 6 April 2001     

Nanoblends of PMMA/aramid: A study on morphological and physical properties

Motivated by the development of miscible nano-blends with supramolecularly organized structures, relying on intermolecular interactions, novel poly(methyl methacrylate) (PMMA)/aramid nano-blend system was designed. Aramid chains, obtained through the condensation of a mixture of 1,5-diaminonaphthalene and 1,3-phenylenediamine with terephthaloyl chloride, were incorporated in PMMA to form nano-structured blends via physical interlocking. Effect of polymer–polymer interactions on miscibility and macroscopic properties of blends were studied using tensile testing, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Tensile properties well indicated the mechanical compatibility resulting from good component cohesion via hydrogen bonding. DSC results also designated entirely miscible blends even at high aramid content. Morphological observations corroborated these findings as well, however, physical interaction of PMMA with varying aramid content efficiently altered blend morphology. Blends with 10, 20, 60 and 70 wt.% aramid possessed fine patterns owing to nano-level compatibility of two phases. Novel blends holding advanced properties can be potentially exploited to acquire exceptional performance in various technological applications such as nano-templates, nano-structured membranes, nano-devices, etc.     

Structure and interactions in homopolymers and blends as studied by the methods of vibrational and nmr spectroscopy

The combination of IR, Raman and NMR spectroscopy was used in the study of the blends of semicrystalline and amorphous polymers with considerably different strength of intermolecular interactions: poly(ϵ-caprolactam)/polystyrene (PCL/PS), poly(ethylene oxide)/poly(methyl methacrylate) (PEO/PMMA) and poly(N-methyllaurolactam)/poly(4-vinylphenol) (PNMLL/PVPh). In the vibrational and NMR spectra of the blends composed of non-interacting polymers (PCL/PS) and weakly interacting polymers (PEO/PMMA), no band changes were observed which would indicate changes of the conformational structures. ¹H NMR relaxation of the PCL and PS components in the blends is the same as in the respective homopolymers similarly treated. In the blends of weakly interacting polymers (PEO/PMMA), the crystallinity of PEO is influenced by the presence of PMMA and is negligible in the blends with less than 30 wt.-% of PEO. The rotating-frame spin-lattice relaxation time for protons T^H_1p of PMMA indicates close contact of the PMMA and PEO chains. In the blends PNMLL/PVPh with strong hydrogen-bonding interactions, both components are intimately mixed on a scale of 3–4 nm and significant shifts of some bands both in vibrational and in NMR spectra reveal changes of structure.     

Spectroscopic characterization of micro-phase separated blends of polystyrene/polymethyl methacrylate (PS/PMMA)

An investigation of the miscibility behaviour in polystyrene/ polymethyl methacrylate (PS/PMMA) blends of various compositions under different evaporations protocols using Fourier transform infrared (FT-IR) and Raman Spectroscopic techniques took place in the study. Solvent selection and evaporation rates, coupled with variations in the blend composition resulted in completely different miscibility behaviour for these systems. In particular, it was found that blends with low PMMA content result in systems that exhibit PMMA domains of less than 7 microns on average. Finally, depth profiling studies of the PMMA moiety in the PS matrix show that the distribution of the low content phase is highly affected by the solvent selection as well as the blend composition.     

SPECTRAL CHARACTERISTICS OF FREE AND LINKED PYRENE-TYPE CHROMOPHORES IN SOLUTION,POLYMER MATRICES,AND INTERPENETRATING NETWORKS

Monomers, 1-pyrenylmethyl methacrylate (PyMMA), 1-pyrenylbutyl methacrylate (PyBMA), 4-(1-pyrenyl)methoxymethyl styrene (PyMMS) and allyl-(1-pyrenylmehtyl) ether (PyMAE), with pyrene as chromophore, were prepared. Their spectral properties (absorption, emission and emission decay) in solution, and doped or bonded in polymer matrices and complex polymer systems as interpenetrating polymer networks (IPN), were investigated. Spectral properties of pyrene-containing monomers doped in polystyrene (PS), polymethylmethacrylate (PMMA), polyvinylchloride (PVC), polyethylene (PE) and grafted on PE as well as copolymerized in buthylmethacrylate-co-styrene copolymer (BMA-co-S) have been compared. Absorption and emission spectra of pyrene type probes in solution and in IPN matrices exhibit typical absorption of the pyrene moiety. For IPN with grafted probes on PE, the absorption is slightly shifted to red wavelength. For monomers, PyMMA, PyBMA and PyMAE grafted to PE, the shape of the emission spectrum depends on the wavelength of excitation. The ratio of intensity of the vibrational band, I₁/I₃, (I₁ peak at 377 nm and I₃ peak at 388 nm) has been a quite useful indicator of polarity of IPN. The relative quantum yields of fluorescence in IPN matrices are lower in comparison to polymer matrices of PE, PS, PMMA for all probes under study. The fluorescence life-times for bound and free probes have been in the range 100–200 ns, which is substiantialy shorter than for the parent pyrene chromophore under the same or similar condition. Grafted probes on PE alone, or as a part of IPN, exhibit substantially shorter life-time around 10 ns and decay is rather complex.     

纳米SiO_2填充PMMA/PS复合物共连续范围的研究

采用流变法、抽提法以及扫描电镜3种表征方法研究了亲水性纳米二氧化硅粒子SiO2填充对聚甲基丙烯酸甲酯(PMMA)/聚苯乙烯(PS)不相容体系共连续范围的影响.对于未填充PMMA/PS体系,3种方法测得的共连续范围基本一致.而对于粒子填充体系,SEM与溶剂抽提法均表明随着粒子含量的增加,体系的共连续范围变宽,这是由于亲水性SiO2粒子选择性填充在极性PMMA相中,导致PMMA相的熔体粘度和弹性均有大幅提高,从而减缓了破坏共连续结构的纤维断裂或回缩等松弛过程.与SEM法和溶剂抽提法相反,流变法测得的共连续范围随粒子含量增加明显变窄,这主要是因为加入SiO2粒子后,PMMA/PS体系的弹性模量和黏度大大提高(加入7vol%的SiO2后分别增加近50倍和5倍),导致填充试样在装样和设定间距之后需要更长的松弛时间才能开始流变测试.试样在测试前长时间处于高温熔体状态时,其共连续结构很容易在界面张力的驱动下发生粗化和破碎,所以得到的共连续反而变窄.SEM和溶剂抽提法比流变法更适合用来判断粒子填充PMMA/PS体系特别是其高填充体系的共连续范围.     

玻璃基板作用下高分子共混物薄膜相形态发展过程

研究了玻璃基板作用下极性高聚物为低组分的共混物薄膜在退火条件下相形态的发展过程 .选用聚苯乙烯 (PS) 聚甲基丙烯酸甲酯 (PMMA)与聚苯乙烯 (PS) 聚ε 己内酯 (PCL)两个体系 ,在玻璃基板上Spin Coating成膜后退火 .由于共混物薄膜中极性相对较大的高聚物组分 (PMMA和PCL)相对于极性较小的PS组分对玻璃基板具有更好的润湿性 ,所以在上述的两个共混薄膜体系中其相形态分别显示PMMA和PCL在低组分比例下最终发展成为连续相 .利用扫描电镜以及元素分析很好地验证了以上的结论 ,并且对其机理进行了解释 .此外 ,改变PS的分子量与PCL共混 ,研究了组分粘度对薄膜相形态发展的影响 .结果表明 ,PS组分粘度越大 ,共混物薄膜相结构发展速度越慢     

Mechanical properties and strain-rate effect of EVA/PMMA in situ polymerization blends

Transparent EVA/PMMA sheets are produced via in situ polymerization of MMA in this work. In the presence of the EVA-graft-PMMA (EVA-g-PMMA), which is synthesized by using tert-butyl peroctoate (t-BO) as initiator during MMA polymerization, EVA can be well dispersed in the PMMA matrix. Both tensile fracture energy and Izod impact strength of the EVA/PMMA blends are higher than those of the neat PMMA. SEM photos show that the grafted copolymer also prevents the dispersed EVA particles from being pulled out from the fracture surface. While the EVA/PMMA blends are investigated at room temperature over the strain rates of four decades (from 1.6 × 10⁻⁴ to 0.16 s⁻¹). It has an obvious transition, whereas the neat PMMA remains brittle over the entire range of strain rates.