基于乳酸-硝酸盐体系化学溶液法的GdBiO_3缓冲层的快速制备

以YSZ为基片对以乳酸为溶剂的Gd Bi O3(GBO)缓冲层的化学溶液法(CSD)快速制备工艺进行了研究,着重研究了工艺温度对挥发和外延过程的影响。研究结果表明,涂覆薄膜中的乳酸可以在115℃-30min内几乎完全挥发,低于100℃时难以完全挥发出无水的硝酸盐混合膜。Ar气中GBO的最佳外延温度为800℃时间为1h。GBO缓冲层CSD法制备总工艺时间约为1.5小时。在此YSZ/GBO缓冲层上CSD法制备的YBa2C3Oz膜的转变温度可达90K。     

热处理温度对化学溶液沉积GdBiO_3薄膜生长的影响

以铋、钆的硝酸盐等制备前驱溶胶体系,用CSD法在SrTiO3(100)基底上制备出c轴织构良好的可作为涂层导体缓冲层的GdBiO3(GBO)薄膜。首先利用差热分析的结果对GBO薄膜分解过程的吸、放热情况进行了研究,确定了较为适当的有机物分解工艺。在此基础上研究了不同外延成相热处理温度对GBO薄膜生长的影响,并对较高温度处理后样品产生裂纹的原因进行了初步分析。GBO薄膜的相组成和微结构利用XRD和SEM进行分析。研究结果表明,在Ar气氛中适宜于GBO薄膜生长的最佳温度在770℃度附近,在此条件下可以制备出表面平整致密的GBO薄膜。     

利用MOCVD在r面蓝宝石上生长的α面GaN中两步AlN缓冲层的优化

采用两步AlN缓冲层(一层低温AlN和一层高温AlN)在r面蓝宝石衬底上生长了非极性的α面GaN,并利用高分辨X射线衍射和光致荧光谱对所生长的材料进行了研究.两步AIN缓冲层在我们之前的工作中已被证明比单步高温AlN或低温GaN缓冲层更有利于减小材料各向异性和提高晶体质量,本文进一步优化了两步AlN缓冲层的结构,并得到...     

Tl系超导薄膜金属涂层的生长与特性研究

我们研究了Tl-2212超导薄膜在带有YSZ/CeO2缓冲层和带有CeO2/YSZ/CeO2缓冲层的Ni金属RABiTS基带上的生长情况.基带上的缓冲层是采用PLD方法制备的,Tl-2212薄膜的制备采用了磁控溅射和后热处理两步方法.XRD 实验结果表明,Tl-2212薄膜都具有很好的C轴垂直于膜面的织构,并具有双向外延生长特性.在CeO2/YSZ/CeO2/Ni基带上制作的Tl-2212薄膜的Tc达到102.8 K,Jc(77 K,0 T)达到2.6 MA/cm2;在YSZ/CeO2/Ni基带上薄膜Tc可达97.7 K,Jc(77 K,0 T)也可以达到0.45 MA/cm2.     

在RABiTS基带上制备Tl-2212超导薄膜

我们研究了Tl-2212超导薄膜在带有YSZ/CeO2缓冲层和带有CeO2/YSZ/CeO2缓冲层的Ni金属RABiTS基带上的生长情况.基带上的缓冲层是采用PLD方法制备的,Tl-2212薄膜的制备采用了磁控溅射和后热处理两步方法.XRD 实验结果表明,Tl-2212薄膜都具有很好的c轴垂直于膜面的织构,并具有双向外延生长特性.在CeO2/YSZ/CeO2/Ni基带上制作的Tl-2212薄膜的Tc达到102.8 K,Jc(77K,0T)达到2.6 MA/cm2;在YSZ/CeO2/Ni基带上薄膜的Tc可达97.7K,Jc (77K,0T)也可以达到0.45MA/cm2.     

大尺寸多孔硅／硝酸盐复合材料的制备

多孔硅是一种具有特殊物理形态的硅单质材料，呈海绵状结构，内部存在大量的纳米孔洞，孔洞表面有一层具有原子直径厚度的氢原子层，这个氢原子层在硅原子和充填在孔洞内的硝酸盐分子之间起着缓冲和隔离作用。在一定的触发条件下，可以发生快速的氧化还原反应，纳米孔洞结构使得多孔硅与硝酸盐之问的界面面积非常大，反应速度非常快，反应释放能量是TNT的7倍，这使得多孔硅／硝酸盐复合材料成为一种潜在的含能材料。     

AlN缓冲层对ZnO薄膜质量的影响

采用脉冲激光沉积法以AlN为缓冲层在Si(100)衬底上制备了ZnO薄膜,并测量了样品的XRD谱、SEM图和PL谱.结果表明,AlN缓冲层可以提高Si衬底上外延生长ZnO薄膜的晶体质量.改变缓冲层的生长温度(50～500 ℃)所制备样品的测量结果表明,较低温度下生长的AlN缓冲层有利于制备高质量的ZnO外延层薄膜,其中AlN缓冲层生长温度为100 ℃时外延生长ZnO薄膜晶体质量最好.     

利用MOCVD在r面蓝宝石上生长的α面GaN中两步AlN缓冲层的优化

采用两步AlN缓冲层(一层低温AlN和一层高温AlN)在r面蓝宝石衬底上生长了非极性的α面GaN,并利用高分辨X射线衍射和光致荧光谱对所生长的材料进行了研究.两步AIN缓冲层在我们之前的工作中已被证明比单步高温AlN或低温GaN缓冲层更有利于减小材料各向异性和提高晶体质量,本文进一步优化了两步AlN缓冲层的结构,并得到了各向异性更小,晶体质量更好的α面GaN薄膜.分析表明,两步AlN缓冲层中的低温AlN层在减小各向异性中起着关键作用.低温AlN层能抑制了优势方向(c轴)的原子迁移,有利于劣势方向(m轴)的原子迁移,从而减小了Al原子在不同方向迁移能力的差异,并为其后的高温AlN缓冲层和GaN层提供"生长模板",以得到各向异性更小、晶体质量更好的α面GaN材料.     

T1系超导薄膜金属涂层的生长与特性研究

我们研究了T1-2212超导薄膜在带有YSZ／CeO2缓冲层和带有Ce02／YSZ／CeO2缓冲层的Ni金属RABiTS基带上的生长情况．基带上的缓冲层是采用PLD方法制备的，T1-2212薄膜的制备采用了磁控溅射和后热处理两步方法．XRD实验结果表明。T1-2212薄膜都具有很好的C轴垂直于膜面的织构，并具有双向外延生长特性．在CeO2／YSZ／CeO2／Ni基带上制作的T1-2212薄膜的Tc达到102．8K，J,（77K,0T）达到2.6MA／cm^2；在YSZ／CeO2／Ni基带上薄膜Tc可达97．7K，Jc（77K,0T）也可以达到0．45MA／cm^2.     

IBAD技术制备涂层导体用YSZ缓冲层长带的研究

在钇钡铜氧(YBCO)高温超导涂层导体制备路线中,离子束辅助沉积技术(IBAD)是两大主流技术路线之一,取得了最为突出的研究成果.本文简要介绍了IBAD技术制备YBCO涂层导体的最新研究进展;并采用离子束辅助沉积技术在哈氏合金(Hastelloy)基底上成功制备了1米长具有钇稳定氧化锆(YSZ)缓冲层的金属基带.采用X射线衍射仪(XRD)分析YSZ缓冲层的取向;利用原子力显微镜(AFM)和扫描电镜(FESEM)观察其表面形貌.获得了可以实际应用的IBAD-YSZ/Hastelloy缓冲层长基带,可以在该基带上研制其他缓冲层以制备YBCO高温超导涂层导体带材.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.