Potentiometric detection of exogenic beta-adrenergic substances in liquid chromatography

Generation of a large number of theoretical plates was attempted by capillary HPLC. Monolithic silica columns having small skeletons (ca. 2 μm) and large through-pores (ca. 8 μm) were prepared by a sol–gel method in a fused-silica capillary (50 μm I.D.), and derivatized to C₁₈ phase by on-column reaction. High external porosity (>80%) and large through-pores resulted in high permeability (K=1.2×10⁻¹² m²). The monolithic silica column in the capillary produced a plate height of about 12 μm in 80% acetonitrile at a linear velocity of 1 mm/s. Separation impedance, E value, was found to be as low as 200, that was about an order of magnitude lower than reported values for conventional columns packed with 5 μm particles. Reproducibility of preparation within ±15% was obtained for column efficiency and for pressure drop. It was possible to generate 100,000 plates by using a 130-cm column at very low pressure (<7 kg/cm²). A considerable decrease in column efficiency was observed at high linear velocity, and for solutes with large retention factors due to the slow mobile-phase mass transfer in the large through-pores. The monolithic silica columns, however, showed performance beyond the limit of conventional particle-packed columns in HPLC under favorable conditions.     

Switching on stray electric fields in ferroelectric liquid crystal cells

In liquid crystal dot-matrix displays light may leak through the display area between the pixels. To obtain sufficient contrast this non-pixel area has to be made non-transmissive. For ferroelectric liquid crystal (FLC) displays this may be done by switching the material in the gaps between the picture elements to a non-transmissive state by the stray electric fields that occur during application of voltages to the pixel electrodes. This is experimentally studied for test cells with an electrically modified smectic layer structure. The gap region considered is an asymmetric environment of the FLC material, as the transparent conductive coating has been removed on one substrate, whereas on the other substrate a conductor covers the glass. The FLC molecules in the non-pixel area prefer to direct their dipoles towards the covered substrate. To switch the FLC material with the stray electric fields, it is a prerequisite to outweigh this preference. We made spatially resolved observations for various gap widths and various applied voltages on 2 μm thick FLC layers. With bipolar voltage pulses of 64 μs width each, amplitudes of about 25 V are needed to switch the FLC in 3·2 or 4·0 μm wide gaps. It was found to be more difficult to switch gaps that, are 7 μm wide than was anticipated on the basis of the results for 4 μm gaps. This is attributed to the surface polarization charge due to the FLC permanent dipoles built up at the FLC-glass interface. Experimental results supporting this explanation are presented.     

An improved bonded-polydimethylsiloxane solid-phase microextraction fiber obtained by a sol-gel/silica particle blend

A novel procedure for solid-phase microextraction fiber preparation is presented, which combines the use of a rigid titanium alloy wire as a substrate with a blend of PDMS sol–gel mixture/silica particles, as a way of increasing both the mechanical robustness and the extracting capability of the sol–gel fibers. The 30 μm average thick fibers displayed an improvement in the extraction capacity as compared to the previous sol–gel PDMS fibers, due to a greater load of stable covalently bonded sol–gel PDMS. The observed extraction capacity was comparable to that of 100 μm non-bonded PDMS fiber, having in this case the advantages of the superior robustness and stability conferred, respectively, by the unbreakable substrate and the sol–gel intrinsic characteristics. Repeatability (n = 3) ranged 1–8% while fiber production reproducibility (n = 3) ranged 15–25%. The presence of the silica particles was found to have no direct influence on the kinetics and mechanism of the extraction process, thus being possible to consider the new procedure as a refinement of the previous ones. The applicability potential of the devised fiber was illustrated with the analysis of gasoline under the context of arson samples.     

Effect of laser modified surface microtopochemistry on endothelial cell growth

The introduction of microelectronics technology in the area of biological sciences has brought forth previously unforeseeable applications such as DNA or protein biochips, miniaturized, multiparametric biosensors for high performance multianalyte assays, DNA sequencing, biocomputers, and substrates for controlled cell growth (i.e. tissue engineering). We developed and investigated a new method using “cold” excimer laser beam technology combined with microlithographical techniques to create surfaces with well defined 3D microdomains in order to delineate critical microscopic surface features governing cell–material interactions. Microfabricated surfaces with microgrooves 30–3 μm deep, 10–1 μm wide spaced 30 μm apart were obtained with micron resolution, by “microsculpturing” polymer model surfaces using a computer controlled laser KrF excimer beam coupled with a microlithographic projection technique. The laser beam after exiting a mask was focused onto the polymer target surface via an optical setup allowing for a 10-fold reduction of the mask pattern. Various 3D micropatterned features were obtained at the micron level. Reproducible submicron features could also be obtained using this method. Subsequently, model human umbilical endothelial cells (HUVEC) were cultured on the laser microfabricated surfaces in order to study the effects of specific microscopic surface features on cell deposition and orientation. Cell deposition patterns were found to be microstructure dependant, and showed cell orientation dependency for features in the cell range dimension, a behaviour significantly different from that of a previously studied cell model (osteoprogenitor cell). This model may be a promising in so far as it is very rapid (a time frame less than a second per square centimeter of micropatterned surface) and provides further insights into the effects of surface microtopography on cell response with possible applications in the field of biosensors, biomedical and/or pharmaceutical engineering sciences.     

Aspects of the synthesis, Characterization and metal–ligand stoichiometry of aminopropyl, nitrobenzamide, and 8-quinolinol silica gels

Surface modification of several silica gels with a number of silanes was studied, as well as further reactions of the modified surfaces. Complete reaction of aminopropylsilane was easily achieved if surface silanols were in excess. Triethoxysilylpropyl-p-nitrobenzamide (TESPN) reacts with difficulty, and complete reaction occured only with long reaction time (at least 12h). The maximum coverage of 100-Å pore silica gel by TESPN was found to be about 1.7 μmol/m², considerably less than the 3–4 /gmmol/m² of available silanol sites, probably due to steric effects of the large silane. Even at this maximum coverage, further reaction of the modified silica with trimethylsilyl capping groups occured, with additional coverage of about 1.0 μmol/m². The maximum amount of silylpropylamido-p-phenylazo-8-quinolinol that could be bound to silica gel was found to be about 1.0 μmol/m², again probably limited by steric effects of the large 8-quinolinol (oxine) moiety. Virtually complete conversion of parent nitrobenzamide silica gel (NBSG) to 8-quinolinol silica gel (QSG) could be achieved if NBSG coverage was less than about 0.7 μmol/m². QSG materials were found to have a 2 oxine to 1 copper(II) stoichiometry, even with surface coverages as low as 0.16 μmol/m².     

Use of short-end injection capillary packed with a glycopeptide antibiotic stationary phase in electrochromatography and capillary liquid chromatography for the enantiomeric separation of hydroxy acids

A new chiral stationary phase (CSP) was prepared by reacting MDL 63,246 (Hepta-Tyr), a glycopeptide antibiotic belonging to the teicoplanin family, with 5-μm diol-silica particles. The CSP mixed with 5-μm amino silica particles (3:1) was packed into 75-μm fused-silica capillaries for only 6.6 cm and used for electrochromatographic experiments analyzing several hydroxy acid enantiomers. A reversed electroosmotic flow carried both analytes and mobile phase towards the anode in a short time (1–3 min), being baseline resolved all the studied analytes. In order to achieve the fastest enantiomeric resolution of the studied hydroxy acids, the effect of several experimental parameters such as mobile phase composition (organic modifier type and concentration, pH of the buffer and ionic strength), capillary temperature and applied voltage on enantioresolution factor, retention time, enantioselectivity were evaluated. The packed capillary column allowed the separation of mandelic acid enantiomers in less than 72 s with resolution factor R_s=2.18 applying a voltage of 30 kV and eluting with a mobile phase composed by 50 mM ammonium acetate (pH 6)–water–acetonitrile (1:4:5, v/v). The CSP was also tested in the capillary liquid chromatography mode resolving all the studied enantiomers applying 12 bar pressure to the mobile phase [50 mM ammonium acetate (pH 6)–water–methanol–acetonitrile, 1:4:2:3, v/v)], however, relatively long analysis times were observed (12–20 min).     

Determination of melatonin in biological samples by capillary electrophoresis

The determination of melatonin (MLT) in physiological samples was investigated using capillary electrophoresis (CE). Mouse blood was collected in tubes containing EDTA, centrifuged at 1500 g for 20 min at 4°C, and stored at −20°C. Plasma samples were extracted with dichloroethane, centrifuged and the aqueous phase was discarded. Then the organic phase was evaporated to dryness. The residue was dissolved in deionized water and filtered with a microfilter (0.22 μm). Separations were carried out using a CE system equipped with a fused silica capillary [80 cm (effective length 52 cm)×75 μm I.D.] and an ultraviolet–visible detector (200 nm), and programmed to provide 25 mM 2-(N-morpholino)ethanesulfonic acid (pH 5.7). Injection was performed hydrostatically by elevating the sample by 10 cm at the cathodic side of the capillary. The calibration curve, reproducibility, recovery and limit of detection were examined, and validation of the method was performed. The result showed that MLT in blood could be easily determined with the new method.     

Fast sample preparation involving MASE and coupled column normal phase liquid chromatography for the rapid trace analysis of dioxins in air-dust samples from fire catastrophe emissions

A new approach has been developed and tested for the urgent analysis of dioxins in samples of air-dust filters originating from catastrophe emissions. The procedure consists of a fast extraction of the sample with microwave solvent extraction (MASE) and acetone as solvent followed by a fast cleanup of the extract with normal phase coupled column liquid chromatography (LC/LC).

The multi-dimensional LC/LC system employs a 50 mm×4.6 mm i.d. column packed with 3 μm silica and a 150 mm×4.6 mm i.d. column packed with 5 μm PYE as the first and second analytical column, respectively. Iso-hexane is used on both columns to perform cleanup and dichloromethane to perform efficient back-flush elution of the compounds from the second column. The obtained polarity-based separation in the first dimension and molecular-structure based separation in the second dimension provides a fast and powerful cleanup.

Validation was done by analysing samples of homemade RIVM air-dust with aged residues (n=8, spiking level about 15 pg mg⁻¹ per compound) of dioxins/furans and samples of reference Urban Dust SRM 1649a (n=4) with both the new approach and the existing conventional procedure and were instrumentally analyzed with capillary gas chromatography and high resolution mass spectrometric detection (GC/HRMS).

In comparison to the existing conventional procedure, the new approach reduces sample processing from several days to several hours per sample.

As regards the aged-residue air-dust samples, the new method shows a good accuracy, precision and high selectivity providing a performance in good agreement with the existing procedure. In SRM air-dust, the concentration of a few compounds obtained by the new method was below (10–50%) the certified value.     

Rapid determination of drugs in biofluids by capillary electrophoresis Measurement of antipyrine in saliva for pharmacokinetic studies

A micellar electrokinetic capillary chromatography method was developed that permitted the resolution of antipyrine from endogenous compounds and its quantitation in neat saliva in as little as 1 min. Final conditions were: SpectraPhoresis 1000, 30(23) cm × 50 μm silica capillary, 50 mM sodium phosphate pH 9.6, 50 mM SDS, 10 s hydrodynamic load, detection scanning 200–300 nm or 260 nm, run 25 kV. To overcome the effects of Joule heating the capillary was cooled to 15°C. Sensitivity was <10 μM and linearity extended to 350 μM. Comparison with an HPLC assay demonstrated that hydrodynamic injection gave a loading bias unless samples and standards were of equal viscosity. For 75 samples from five subjects the correlation of CE vs. HPLC was then r = 0.99.     

Biosensor for phenol based on the direct electron transfer blocking of peroxidase immobilising on silica–titanium

Horseradish peroxidase (HRP) was immobilised on silica gel modified with titanium oxide. This material was employed to prepare modified carbon paste electrode. The direct electron transfer of the hydrogen peroxide reduction by HRP was blocked when immobilised on silica–titanium. This biosensor presented a very sensitive response for phenol (1 μmol l⁻¹) at an applied potential of 0 mV vs SCE. The best condition was achieved in phosphate buffer pH 6.8, ratio of hydrogen peroxide/phenol higher than 0.35. The biosensor showed a linear response range between 10 and 50 μmol l⁻¹ of phenol, adjusted by the equation j=−32.8+16.3 [phenol], for n=5 with a correlation coefficient of 0.9995. The response time of the biosensor was about 3 s.     

Packed-column hydrodynamic chromatography using 1-μm non-porous silica particles

150×3 mm I.D. columns, packed with 1-μm non-porous spherical silica particles, were used to separate soluble synthetic polymers by hydrodynamic chromatography. The columns exhibited a plate height of about 1.4 μm allowing very fast and efficient separations of polymers in the molecular mass range 10³−2·10⁶ g/mol. The migration behaviour of polymers could be well described by a simple theoretical model. The applicability of packed bed HDC for the fast separation of polymers was illustrated with separations of polystyrene and poly(methyl methacrylate) mixtures.     

Determination of arsenic(III) and arsenic(V) by electrothermal atomic absorption spectrometry after complexation and sorption on a C-18 bonded silica column

A flow injection procedure for the separation and pre-concentration of inorganic arsenic based on the complexation with ammonium diethyl dithiophosphate (DDTP) and sorption on a C-18 bonded silica gel minicolumn is proposed. During the sample injection by a time-based fashion, the As³⁺-DDTP complex is stripped from the solution and retained in the column. Arsenic(V) and other ions that do not form complexes are discarded. After reduction to the trivalent state by using potassium iodide plus ascorbic acid, total arsenic is determined by electrothermal atomic absorption spectrometry (ETAAS). Arsenic(V) concentration can be calculated by difference. After processing 6 ml sample volume, the As³⁺-DDTP complexes were eluted directly into the autosampler cup (120 μl). Ethanol was used for column rinsing. Influence of pH, reagent concentration, pre-concentration and elution time and column size were investigated. When 30 μl of eluate plus 10 μl of 0.1% (w/v) Pd(NO₃)₂ were dispensed into the graphite tube, analytical curve in the 0.3–3 μg As l⁻¹ range was obtained (r=0.9991). The accuracy was checked for arsenic determination in a certified water, spiked tap water and synthetic mixtures of arsenite and arsenate. Good recoveries (97–108%) of spiked samples were found. Results are precise (RSD 7.5 and 6% for 0.5 and 2.5 μg l⁻¹, n=10) and in agreement with the certified value of reference material at 95% confidence level.     

Use of silica gel chemically modified with zirconium phosphate for preconcentration and determination of lead and copper by flame atomic absorption spectrometry

An analytical method using silica gel chemically modified with zirconium (IV) phosphate for preconcentration of lead and copper, in a column system, and their sequential determination by flame atomic absorption spectrometry (FAAS), was developed. Sample solutions are passed through a glass column packed with 100 mg of the sorbent material, at pH 4.5, and lead and copper are eluted with 1.0 mol l⁻¹ HNO₃ at a flow rate of 2.0 ml min⁻¹. The extraction of copper is affected by Fe(II), Mn(II), Zn(II), Ni(II) and Co(II) while only Fe(II) interferes in the lead determination. These interferences may be overcome with an appropriate addition of a KI or NaF solution. An enrichment factor of 30 was obtained for both metals. While the limits of detection (3σ) were 6.1 and 1.1 μg l⁻¹, for Pb and Cu, respectively, the limits of determination were 16.7 and 3.3 μg l⁻¹. The precision expressed as relative standard deviation (R.S.D.) obtained for 3.3 μg l⁻¹ of Cu and 16.7 μg l⁻¹ of Pb were 4.3 and 4.7%, respectively, calculated from ten measurements. The proposed method was evaluated with reference material and was applied for the determination of lead and copper in industrial and river waters.     

Synthesis and characterization of highly ordered BiFeO3 multiferroic nanowire arrays

We report the synthesis and characterization of multiferroic BiFeO₃ (BFO) nanowires. The perovskite BFO nanowires with diameters about 60 nm and lengths about 10 μm were fabricated by means of the sol-gel method utilizing nanochannel alumina templates with post annealing at 700 °C. The microstructure of the BFO nanowires was investigated by means of x-ray diffraction and transmission electron microscopy, and the ferroelectric characteristic of BFO nanowires were demonstrated.     

Evaluation of solid-phase micro-extraction coupled to gas chromatography-mass spectrometry for the headspace analysis of volatile compounds in cocoa products

The aroma profile of cocoa products was investigated by headspace solid-phase micro-extraction (HS-SPME) combined with gas chromatography–mass spectrometry (GC–MS). SPME fibers coated with 100 μm polydimethylsiloxane coating (PDMS), 65 μm polydimethylsiloxane/divinylbenzene coating (PDMS-DVB), 75 μm carboxen/polydimethylsiloxane coating (CAR-PDMS) and 50/30 μm divinylbenzene/carboxen on polydimethylsiloxane on a StableFlex fiber (DVB/CAR-PDMS) were evaluated. Several extraction times and temperature conditions were also tested to achieve optimum recovery. Suspensions of the samples in distilled water or in brine (25% NaCl in distilled water) were investigated to examine their effect on the composition of the headspace. The SPME fiber coated with 50/30 μm DVB/CAR-PDMS afforded the highest extraction efficiency, particularly when the samples were extracted at 60 °C for 15 min under dry conditions with toluene as an internal standard. Forty-five compounds were extracted and tentatively identified, most of which have previously been reported as odor-active compounds. The method developed allows sensitive and representative analysis of cocoa products with high reproducibility. Further research is ongoing to study chocolate making processes using this method for the quantitative analysis of volatile compounds contributing to the flavor/odor profile.     

Sensitive and selective ion chromatographic method for the determination of trace beryllium in water samples

A selective and sensitive ion chromatographic method has been developed for the determination of beryllium in a number of water samples at low-μg/l concentrations. The separation was performed on a 250×4.0 mm I.D. iminodiacetic acid functionalised silica gel column. Chromatographed Be(II) was detected using visible detection at 590 nm following post-column reaction with chrome azurol S (CAS). The optimum separation and derivatisation conditions were studied in detail. The optimum eluent conditions were found to be 0.4 M KNO₃, adjusted to pH 2.5 using HNO₃, with optimum post-column detection being achieved using a solution containing 0.26 mM CAS, 2% Triton X-100, 50 mM 2-(N-morpholino)ethanesulfonic acid, pH 6.0. Under the above conditions, the concentration detection limit for Be(II) was found to be 3 μg/l in a standard solution and 4 μg/l in a typical tap water sample, using a 250 μl injection. The method was linear over the investigated range of 10 μg/l to 10 mg/l and highly reproducible. The method was successfully applied to a number of water samples of varying matrix complexity, including simulated seawater, and also to a natural freshwater certified reference material NIST 1640.     

新型SiO2/SiO2核壳型固定相的制备与评价

采用层层自组装的方法,以微米多孔硅胶小球为核,将硅胶纳米粒子多层包覆,制备了核壳型SiO2/SiO2硅胶小球.透射电子显微镜表明这种硅胶小球具有明显的核壳结构,氮气吸附实验证明该硅胶小球是典型的介孔材料,具有良好的介孔结构和窄的孔径分布.将其作为基质制备碳十八键合核壳型SiO2/SiO2色谱固定相,该固定相的碳含量与未...     

Determination of vitamin B12 in multivitamin tablets by multimode high-performance liquid chromatography

Quantitative determination of vitamin B₁₂ in B-complex tablets was performed by using multimode high-performance liquid chromatography. The multivitamin tablets (B₁, B₆ and B₁₂) were sonicated for 30 min in methanol–water (50:50, v/v) and diluted to appropriated volume with the same solvent. The resulting solution was filtered and the filtrate was analysed on a phenylpropanolamine bonded silica column (15 cm×4.6 mm I.D., 5 μm). The optimized mobile phase was 30 mM phosphate buffer (pH 3.00) containing 6% (v/v) acetonitrile at a flow-rate of 1 ml min⁻¹ and the detection was measured at 361 nm. The calibration graph prepared using standards was linear from 0.05 to 0.25 μg. The determination limit was 25 ng, the relative standard deviation was 0.47% and recovery from tablet solution was 100%. An analysis was completed in 5 min. The new method is simple, rapid and precise.     

Photoageing of rigid PVC—II. Degradation thickness profiles

Bulk samples of non-photostabilized PVC were exposed in a photochemical reactor equipped with a fluorescent lamp (λ ≥ 300 nm) at 70 °C. After 500 h of exposure, thin (20 μm) slices parallel to the surface were cut with a microtome and analyzed by FTIR and UV spectrophotometry and steric exclusion chromatography. The results reveal the existence of at least three distinct zones: (a) The superficial zone of thickness lower than 100 μm, which is characterized by the predominance of oxidation products and chain scissions; (b) The subcutaneous zone, in the 100–400 μm depth interval characterized by the predominance of the products of HC1 zip elimination (conjugated polyenes) and crosslinking (increase of M_w; and (c) The undegraded core zone beyond 400 μm depth. These characteristics can be partially explained in terms of diffusion controlled oxidation kinetics, but with some peculiarities linked to conjugated polyenes. Among these are the consequences of their photoreactivity and screen effect, and the fact that they are concentrated in fractions of high molecular weight.     

Determination of mercury by differential-pulse anodic-stripping voltammetry with various working electrodes Application to the analysis of natural water sediments

Four types of working electrode (glassy-carbon and gold rotating-disk electrodes and two types of gold-film electrode) have been used in determination of traces of mercury by differential-pulse anodic-stripping voltammetry, and the analytical parameters of the procedures compared. The technique has been applied to the analysis of river sediments. The lowest limit of detection (0.02 μg/l.) was obtained with the gold rotating-disk electrode. Two procedures have been found optimal for analyses of sediment samples; determination with the gold rotating-disk electrode and solution-exchange after the preelectrolysis, and determination with the gold-film electrode prepared in situ in the sample extract. The sample pretreatment involved a separation of the 0.45–63 μm fraction, mineralization with a mixture of hydrochloric and nitric acids (3:1 or 1:3) under atmospheric pressure in a fused silica vessel, followed by irradiation with ultraviolet light, after addition of hydrogen peroxide (to destroy organic matter). The most serious interference is from iron; this can be prevented by adding fluoride or pyrophosphate. The procedure is an alternative to the AAS determination of the total mercury content in sediments, especially with heavily polluted samples (mercury concentrations up to 0.01%).