Analysis of ions in polar ice core samples by use of large injection volumes in ion chromatography

In the present study a non-suppressed ion chromatography system with conductivity detection was tested in terms of sampling effects, the effects on the ion separation efficiency and analysis detection limits to find optimum conditions for the determination of chloride, nitrate, sulfate, sodium, ammonium, potassium, calcium and magnesium ions in polar ice core samples.     

Simultaneous separation of inorganic anions and cations by capillary zone electrophoresis

A new capillary electrophoretic approach for simultaneous separation of fast anions and cations is demonstrated. Indirect UV detection at 214 nm in conjunction with electromigration sampling from both ends of the capillary was developed. Two electrolyte systems based on imidazole-nitrate and copper(II)-ethylenediamine-nitrate were investigated for the simultaneous separation of chloride, sulphate, hydrocarbonate, potassium, ammonium, calcium, sodium and magnesium ions. Experimental parameters that were evaluated included a nature of UV chromophore, pH of electrolyte, a nature of complexing agent. The method permits the excellent separation of three anions and five cations in only 4 min using electrolyte system containing 2.5 mmol l⁻¹ Cu(NO₃)₂, 5 mmol l⁻¹ ethylenediamine and 1 mmol l⁻¹ fumaric acid at pH 8.5 adjusted with tetraethylammonium hydroxide.     

Determination of anionic trace impurities in glycerol by capillary isotachophoresis with enlarged sample load

Glycerol of different quality classifications served as a model for a neutral excess component in the isotachophoretic determination of low-molecular-mass anionic trace impurities. Potential anionic contaminants such as nitrate, sulphate, chlorate, nitrite, oxalate, fluoride formate and phosphate were analysed up to an analyte-to-excess ratio of 1:4·10⁷, thus providing the possibility of checking the sample for the mentioned analytes in the order of 2.5·10⁻⁶–9.5·10⁻⁶%. Because we used a column-coupling isotachophoretic instrument the electrolyte system consisted of two different leading electrolytes, one for the pre-separation (10 mmol/l HCl, β-alanine, pH 3.2) in the first capillary and one for the final separation (5 mmol/l HCl, 1,3-bis[tris(hydroxymethyl)methylamino]propane, β-alanine, pH 3.6) in the second capillary. The terminating electrolyte was citric acid. Due to an increased injection volume of 300 μl, limits of detection (LODs) in the nanomolar range were realised by conductivity detection. The developed method allows simultaneous analysis without sample preparation and/or preconcentration within 25 min and is for that reason suitable for in-place process control.     

Integrated moulded polymer electrodes for performing conductivity detection on isotachophoresis microdevices

The feasibility of using integrated injection moulded polymer electrodes as drive and detection electrodes for performing miniaturised isotachophoresis (ITP) separations with conductivity detection has been demonstrated. Injection moulded electrodes were produced from three different grades of carbon-filled polymer. Two of the electrode designs were found to be suitable for performing on-chip conductivity detection. The high-voltage characteristics of the microdevices were found to be suitable for performing ITP, with a power dissipation up to 1.4 W m⁻¹ being achieved. Three model separations are presented to demonstrate the separation capability of the miniaturised injection moulded devices. Three anionic dyes, two inorganic anions and a mixture of eight alkaline earth, transition and lanthanide metal cations were analysed.     

Comparison of ion chromatography and capillary electrophoresis for the determination of inorganic ions

The techniques of ion chromatography and capillary electrophoresis are compared as analytical methods for the determination of inorganic anions and cations. Comparison is made in the areas of stage of development, separation efficiency, separation selectivity, analytical performance parameters, method development procedures, applications, strenghts and weaknesses, and future directions. It is shown that the two techniques are complementary rather than competitive, especially with regard to their separation selectivities and the type of applications to which they are most suited.     

Analysis of wastewater for anionic and cationic nutrients by ion chromatography in a single run with sequential flow injection analysis

To prevent nutrient enrichment and, hence the undesirable ecological impacts, the nutrients monitored in wastewater samples include two anionic species, i.e., nitrate and orthophosphate, and a cationic species, ammonium. Ion chromatography (IC) is one of the popularly used techniques for determinations of nitrate and phosphate in these samples, whereas determination of ammonium in wastewater samples is typically done using manual or automated wet chemistry, e.g., flow injection analysis (FIA). We have developed a sequential IC–FIA method, using Lachat’s QC8000 IC system, which allows determinations of nitrate, phosphate and ammonia in a single injection. In this system, a QuikChem Small Suppressor cartridge is regenerated in between the samples. A sample is injected while leaving the suppressor off-line. Ammonium, a cation, elutes in the void volume of an anion-exchange column. The unsuppressed column effluent, exiting the conductivity flow cell, up to this point is used for FIA determination of ammonia. When ammonia exits the conductivity flow cell, a fully regenerated suppressor is brought in-line for conductometric detection of the anions. Analog data are simultaneously acquired from colorimetric and conductometric detectors, for the cationic and anionic nutrients, respectively. The method is accurate with spike recoveries in wastewater samples ranging from 91% for nitrate to 114% for chloride. It is precise with RSD values, for replicate analyses (n=7) of a mid-range standard, ranging from 0.4% for phosphate to 1% for nitrate.     

Quantitative determination of inorganic minor cations in sodium-, calcium-, magnesium-matrix simulated samples by capillary electrophoresis

The analysis of ammonium, alkali and alkaline-earth trace cations (0.5 ppm) in samples with a calcium, sodium or magnesium matrix (500 ppm) has been achieved using 10 mM imidazole (pH 4.5) electrolyte to which a complexing agent (15-crown-5, oxalic acid or dipicolinic acid) has been specifically added in order to decrease the electrophoretic mobility of the matrix cation and thus to allow the separation of higher mobility cations at sub-ppm concentrations. The influence of several experimental parameters (complexing agent concentration, buffer pH and temperature) have been studied in order to optimize the separation. The complexing agent concentration appears to be the main parameter governing the selectivity of the cations during the analysis of matrix samples. In optimized conditions, we have checked that the separation between minor inorganic cations is not significantly altered by an increase in the matrix cation concentration. As the concentration of the matrix cation increases, the migration times of minor cations remain unchanged even for a 1000 ppm concentration of the matrix cation. Finally, these optimized buffers allow the quantitation of minor cations down to 0.05% (w/w) for calcium- or magnesium- matrix simulated samples and 0.2% (w/w) for sodium-matrix simulated samples.     

Ultra-pure water for ion chromatography

Water with ionic concentrations substantially below 1 μg/l is an increasing requirement for high sensitivity ion chromatographic analysis. The resistivity of the water is not an adequate guide to impurity levels at less than 1 μg/1 due to the practical limitations in resistivity measurement and to the non-linear variation of resistivity with impurity ion concentration. A water purification system is described using inter-stage monitoring to overcome these limitations and to ensure ultra-trace ionic levels. Some examples of cation analyses are included.     

Monitoring the removal of soluble salts from ancient tiles by ion chromatography

The application of ion chromatography, conductometry and total carbon analysis to the study of desalination of 18th century tiles and mortars is described. Ion chromatography is shown to be a simple and adequate technique for the identification and quantitative analysis of ions which are extracted during desalination. Chloride, nitrate, sulphate, carbonate, sodium, potassium, calcium and magnesium were always found in the immersion waters, and occasionally also nitrite and oxalate.     

Capillary electrophoresis for measuring major and trace anions in thermal water and condensed-steam samples from hydrothermal springs and fumaroles

A new application of capillary electrophoresis for measuring major and trace anions in thermal water and condensed-steam samples is presented. Ten fluid samples were collected from hydrothermal springs and fumaroles located in a volcanic zone of Deception Island, Antarctica. Anion separation was achieved in less than 6 min using indirect UV detection at 254 nm with a negative power supply (−15 kV). The electrolyte consisted of 4.7 mM sodium chromate, 4.0 mM electroosmotic flow modifier (OFM) hydroxide, 10 mM 2-(N-cyclohexylamino)ethanesulfonic acid and 0.1 mM calcium gluconate (pH 9.1). Major anions (Cl⁻, SO₄², PO₄H²⁻, and CO₃H⁻) were measured using hydrostatic injection (10 cm for 30 s) at 25°C. Trace amounts of anions (F⁻, Br⁻, and NO₃⁻) were better determined by electromigration injection (4 kV, 10 s) at 15°C. Good reproducibility of the migration times (<0.72% RSD), a satisfactory linear response and accuracy as well as acceptable detection limits were successfully obtained.     

Acid-rain monitoring in East Asia with a portable-type ion-exclusion–cation-exchange chromatographic analyzer

A monitoring system consisting of a portable-type conductimetric ion-exclusion–cation-exchange chromatographic (CEC) analyzer and a meteorological satellite data analyzer has been investigated for the evaluation of the effects of acid precipitation on natural and urban environments in East Asia. The portable ion-exclusion–CEC analyzer uses a polymethacrylate-based weakly acidic cation-exchange resin column in the H⁺-form and a weak-acid eluent (tartaric acid–methanol–water) and is applied for the simultaneous determination of anions (SO₄²⁻, NO₃⁻, and Cl⁻) and cations (Na⁺, NH₄⁺, K⁺, Mg²⁺, and Ca²⁺) in precipitation transported from mainland China to central Japan, as mapped by the meteorological satellite data analyzer. Linear calibration graphs of peak area versus concentration for anions and cations were observed in the concentration range 0–1.0 mM for the anions and 0–0.5 mM for the cations. Detection limits at a signal-to-noise ratio of 3 were in the range 5.18–12.1 ppb for the anions and 6.58–16.5 ppb for the cations. The practical utility of this monitoring system is presented.     

Chemical conditions inside occluded regions on corroding aircraft aluminum alloys

Corrosion of aluminum alloy structures costs the US Air Force in the order of US$1×10⁹ annually. Corrosion develops in areas of overlap such as aircraft lap-splice joints and under protective organic coatings. Capillary electrophoresis (CE) has been used to determine the local chemistries at these corrosion sites of solutions that were extracted using a microsampling system. Analysis of the local solution within lap-splice joints from aircraft has been performed in two ways: rehydration of corrosion products and direct microsampling. The solutions collected were analyzed with CE to quantitatively determine the species present during corrosion. The most common ions detected were Cl⁻, NO₂⁻, NO₃⁻, HCO₃⁻, K⁺, Al³⁺, Ca²⁺, Na⁺ and Mg²⁺. Studies of the solution chemistry under local coating defects are required to understand coating failure and develop more durable coatings. A microsampling system and micro pH sensor were developed to extract solution from and measure pH in defects with diameters as small as 170 μm. Actively corroding defects contained high concentrations of Cl⁻, Al³⁺, Mg²⁺, Mn²⁺ and Cu²⁺ whereas only trace levels of Mg²⁺ were found in repassivated defects. The effects of these species on initiation and propagation of corrosion are discussed.     

Analysis of metabolites of glucose pathways in human erythrocytes by analytical isotachophoresis

A method for the quantitative determination of the major anionic constituents of fountain solutions, typically mono-, di- and hydroxycarboxylates, alkylbenzenesulfonates, and inorganic anions, including orthophosphate and polyphosphates, is presented here for the first time. The analytical problems arising from extensive co-elution of many of these analytes on an ion-exchange column have been resolved through a combination of (i) careful selection of the concentration gradient of the sodium hydroxide eluent; (ii) parallel analysis by ion-exclusion chromatography; and (iii) determination of total phosphorus by inductively coupled plasma atomic emission spectrometry.     

毛细管电泳定量检测环境水样中无机阴离子

详细讨论了胶束浓度、间接吸收背景物质的浓度及有机添加剂组成等对部分卤素及其含氧酸根的毛细管电泳分离影响;在优化的条件下,3.5min内高效、快速地完成了Cl-、Br-、ClO3-、BrO3-四种无机阴离子的分离分析,分离的理论塔板数在1.6×106～2.8×105/m之间,检出限在11.2～23.3mg/L之间,迁移时间的相对标准偏差小于1%,峰面积的相对标准偏差在5.2%～2.2%之间;并将方法用于环境水样的分析。     

Factors affecting selectivity of inorganic anions in capillary electrophoresis

Capillary zone electrophoretic separations of inorganic anions are largely governed by the intrinsic (infinite dilution) mobility of the anion. This in turn is a function of the hydrodynamic friction caused by the size of the ion and the dielectric friction caused by the charge density of the anion re-orienting the surrounding solvent. The influence of these factors on the mobility of anions is examined in both water and nonaqueous solvents. The influence of other experimental parameters, such as ionic strength, ion association, electroosmotic flow modifier concentration, and the addition of complexing agents such as polymeric cations, cyclodextrins, crown ethers and cryptands are also reviewed. From this discussion, some rules of thumb as to when different approaches will be most effective are drawn.     

Performance of ion chromatography in the determination of anions and cations in various natural waters with elevated mineralization

The performance of ion chromatography in the determination of anions and cations in natural mineral waters of different composition and different total mineralization was evaluated. Up to 12 ions of the 20 usually included in extended chemical analysis of natural waters were successfully determined by ion chromatography alone. At least 98.60% and up to 99.96% of total cation composition of mineral waters was determined by ion chromatography. Hydrogen carbonate predominated in anion composition of mineral waters and was determined titrimetrically. The percentage of anions determined by ion chromatography in the remaining anion composition of mineral waters was between 98.90% and 99.96%. The agreement between total concentrations of anions and cations in individual mineral waters determined predominantly by ion chromatography is very good and the performance of ion chromatography for the basic and for the extended chemical analysis of highly mineralized water samples is very high. Method development was assisted by previously developed algorithms and appropriate experimental conditions are also discussed.     

Separation of inorganic anions in acidic solution by capillary electrophoresis

Inorganic anions are almost always determined by capillary electrophoresis (CE) at an alkaline pH, so the analytes will be fully ionized. However, a long-chain quaternary ammonium salt usually must be added as a flow modifier to the carrier electrolyte to reverse the direction of the electroosmotic flow. By working at a sufficiently acidic pH, the electroosmotic flow in fused-silica capillaries is virtually eliminated, and anions can be separated simply by differences in their electrophoretic mobilities. Excellent separations were obtained for AuCl₄⁻ and the chloro complexes of platinum group elements in HCl solution at pH 2.0 to 2.4. No additional buffer or flow modifier was needed. This CE technique is an excellent way to follow slow hydrolytic reactions in which one or more of the chloride ligands is replaced by water. Sharp peaks and good separations were also obtained for MnO₄⁻, VO₃⁻, chromate, molybdate, ferrocyanide, ferricyanide and stable complex ions such as chromium oxalate (CrO₃³⁻).     

Continuous melting and ion chromatographic analyses of ice cores

A new method for determining concentrations of organic and inorganic ions in ice cores by continuous melting and contemporaneous ion chromatographic analyses was developed. A subcore is melted on a melting device and the meltwater produced is collected in two parallel sample loops and then analyzed simultaneously by two ion chromatographs, one for anions and one for cations. For most of the analyzed species, lower or equal blank values were achieved with the continuous melting and analysis technique compared to the conventional analysis. Comparison of the continuous melting and ion chromatographic analysis with the conventional analysis of a real ice core segment showed good agreement in concentration profiles and total amounts of ionic species. Thus, the newly developed method is well suited for ice core analysis and has the advantages of lower ice consumption, less time-consuming sample preparation and lower risk of contamination.     

New block-grafted anion exchanger for environmental water analysis by ion chromatography

The IonPac AS14A is a recently developed stationary phase that was produced using a new block-grafting technique, which enables the preparation of high-water-content anion exchangers with excellent peak shape and good chromatographic efficiency. The performance of this column for the analysis of inorganic anions was compared to that obtained using an IonPac AS4A column, which is specified in US Environmental Protection Agency Method 300.0, in addition to another commonly used alternative; the AS14 column. The AS14A column is available in two different formats; 250×4 mm I.D. (7.0 μm diameter particle) and 150×3 mm I.D. (5.5 μm diameter particle). The IonPac AS14A (in 4 mm I.D. format) was found to provide similar performance to the AS14 column with increased peak efficiency and better pH stability and is a suitable alternative for the analysis of anions in moderate- to high-ionic-strength samples. The IonPac AS14A (in 3 mm I.D. format) provides comparable run times to the AS4A column with better overall peak selectivity and improved fluoride resolution, hence this column would be a suitable column to substitute in place of either the AS4A or AS14 columns for the analysis of inorganic anions in low- to moderate-ionic-strength environmental waters. The AS14A column used with an Atlas electrolytic suppressor provides equivalent method detection limits to those obtained when using a micromembrane suppressor but with the operational convenience of a self-regenerating suppressor.     

Application of an external contactless conductivity detector for the analysis of beverages by microchip capillary electrophoresis

Quantitative total ionic analysis of alcoholic and nonalcoholic beverages was performed by microchip capillary electrophoresis with external contactless conductivity detection. An electrolyte solution consisting of 10.5 mM histidine, 50 mM acetic acid, and 2 mM 18-crown-6 at pH 4.1 was used for the determination of NH(4) (+), K(+), Ca(2+), Na(+), and Mg(2+). Fast analysis of Cl(-), NO(3) (-), and SO(4) (2-) was achieved in 20 mM 2-(N-morpholino)ethanesulfonic acid /histidine electrolyte solution at pH 6.0 and the simultaneous separation of up to 12 inorganic and organic anions was performed in a solution containing 10 mM His and 7 mM glutamic acid at pH 5.75. Limits of detection ranged from 90 to 250 mug/L for inorganic cations and anions, and from 200 to 2000 mug/L for organic anions and phosphate. Calibration curves showed linear dependencies over one to two orders of magnitude when the stacking effect was minimized by injecting standard solutions prepared in background electrolyte solutions. Total analysis times of 35 and 90 s were achieved for the determination of 5 inorganic cations and for the simultaneous determination of 12 inorganic and organic anions, respectively, which represents a considerable reduction of analysis time compared to conventional separation methods used in food analysis.