Rapid determination of 90Sr/90Y in water samples by liquid scintillation and Cherenkov counting

Strontium-90 (⁹⁰Sr) is a ubiquitous contaminant at nuclear facilities, found at high concentrations in spent nuclear fuel and radioactive waste. Due to its long half-life and ability to be transported in groundwater, an accurate method for measuring ⁹⁰Sr in water samples is critical to the monitoring program of any nuclear facility. To address this need, a rapid procedure for sequential separation of Sr/Y was developed and tested in groundwater samples collected from an area of riverbed affected by a ⁹⁰Sr groundwater plume. Sixteen samples, plus spike and water blanks, were analyzed. Five different measurements were performed to determine the ⁹⁰Sr and yttrium-90 (⁹⁰Y) activities in the samples: direct triple-to-double-coincidence ratio (TDCR) Cherenkov counting of ⁹⁰Y, liquid scintillation (LS) counting for ⁹⁰Sr following radiochemical separation, LS counting for ⁹⁰Y following radiochemical separation, Cherenkov counting for ⁹⁰Y following radiochemical separation and LS counting of the Sr samples for ⁹⁰Y in-growth. The counting was done using a low-level Hidex 300SL TDCR counter. Each measurement method was compared for accuracy, sensitivity and efficiency. The results following Cherenkov counting and radiochemical separation were in very good agreement with one another.     

Measurement of (90)Sr in environmental samples by cation-exchange and liquid scintillation counting

A new method for the measurement of (90)Sr in environmental samples by cation-exchange and liquid scintillation counting is described. Strontium carbonate is purified by precipitation and ion-exchange, weighed for the determination of chemical yield, dissolved in hydrochloric acid and mixed with the liquid scintillator, Aquasol-2. Two channels of a low-background liquid scintillation counter are used to determine (90)Sr, (90)Y and (89)Sr, free from the effects of environmental tritium. The values of (90)Sr obtained by this method are in good agreement with those from ordinary (90)Y milking and the gas proportional counting method. The concentration of (90)Sr in the air at Tokai-mura in Japan has been measured by the new method.     

Assay of89Sr in plant and soil samples by liquid scintillation counting

The Sr in plant and soil samples is converted to SrCl₂ by digestion with HNO₃ and HCl. The recovery of this digestion is 90% with a reproducibility of about 4%. SrCl₂ is solubilized in toluene by forming a complex with di-n-propyl phosphate (DNP). The DNP-toluene reagent was found to be a highly effective carrier of SrCl₂, and to have properties suitable for highly efficient liquid scintillation counting. An efficiency of 95% was obtained for⁸⁹Sr counting. The factors affecting the utility of the method are discussed.     

Determination of 210Pb by measurement of 210Pb and its progenies using a liquid scintillation counter

Journal of Radioanalytical and Nuclear Chemistry - Lead-210 is a useful tracer in environmental studies for a wide range of applications, particularly in atmospheric research and geochronology....     

Radiometric analysis of <Superscript>90</Superscript>Sr in fish bone ash samples by liquid scintillation counting after separation by extraction chromatographic resin

Studies on the extraction behavior and immobilization of cadmium by greener reagents have important bearings in today’s science. No-carrier-added (NCA), ¹⁰⁹Cd radionuclide is a potential candidate towards radiopharmaceutical studies for both in vivo and in vitro applications and is also used in industrial and environmental studies. Herein, we have studied the adsorption and desorption characteristics of cadmium in both NCA and bulk concentrations into calcium alginate using radiochemical method. Various isotherms like Langmuir, Freundlich, Temkin and Dubinin–Radushkevich have been studied and compared to match the adsorption phenomenon. A spontaneous endothermic physisorption process is expected from thermodynamic parameters.     

Determination of 90Sr and 210Pb in freshwater fish in Austria

A method for the determination of ⁹⁰Sr and ²¹⁰Pb in freshwater fish was developed. The determinations were conducted within a project on behalf of the Federal Ministry of Health. The aim of this project was to get an overview of the activity concentrations of natural and artificial radionuclides in freshwater fish in different lakes in Austria. For sampling the Neusiedler See in Burgenland, two lakes in Styria the Grundlsee and the Toplitz See, and the Zeller See in Salzburg were chosen. Chub (Leuciscus cephalus), pike (Esox lucius), perch (Perca fluviatilis), carp (Cyprinus carpio), catfish (Silurus glanis), pike-perch (Sander lucioperca) and burbot (Lota lota) were analysed. The samples were analysed using strontium specific extraction columns (Eichrom Industries Inc., TrisKem International) and liquid scintillation counting. In the edible parts of the fish samples (no fishbone) values of the activity concentration for ²¹⁰Pb varied between 0.009 ± 0.003 and 0.16 ± 0.04 Bq kg _freshweight ^?1 and for ⁹⁰Sr between 0.010 ± 0.002 and 0.11 ± 0.02 Bq kg _freshweight ^?1 . In this paper the method for the determination of ⁹⁰Sr and ²¹⁰Pb is described and the results are discussed.     

Determination of90Sr in environmental and biological materials with combined HDEHP solvent extraction-low liquid scintillation counting technique

Low level⁹⁰Sr in environmental and biological samples is determined using a combined HDEHP solvent extraction-liquid scintillation procedure. Yttrium-90 is selectively extracted from nitric acid solution into 5% di(2-ethylhexyl) phosphoric acid (HDEHP) in toluene, and⁹⁰Y in the organic phase is measured directly using an ultra low level liquid scintillation spectrometer.The working program of the Quantulus counter has been optimized. As the counting efficiency using liquid scintillation counting is high and the stripping and precipitation of Yttrium-90 oxalate is omitted, this procedure is simpler and more timesaving than traditional methods. The chemical recoveries of⁹⁰Y were 85.1% for soil, 75.7% for milk and 65.3% for bone. The detection limit is 8 mBq.     

Determination of 90Sr in urine samples and 89Sr/90Sr in water samples by chemical separation and Cherenkov counting with LSC system

Journal of Radioanalytical and Nuclear Chemistry - In order to determine radiostrontium with a satisfactory chemical yield, calculated by an external standard, and a low level of MDC a...     

Uranium determination in water samples by liquid scintillation counting after cloud point extraction

The aim of this study is the radiometric determination of uranium in waters by liquid scintillation counting (LSC) after pre-concentration of the element by cloud point extraction (CPE). For CPE, tributyl phosphate (TBP) is used as the complexing agent and (1,1,3,3-Tetramethylbutyl)phenyl-polyethylene glycol (Triton X-114) as the surfactant. The measurement is performed after phase separation by mixing of the surfactant phase with the liquid scintillation cocktail. The effect of experimental conditions such as pH, reactant ratio (e.g. m(TBP)/m(Triton), ionic strength (e.g. [NaCl]) and the presence of other chemical species (e.g. Ca²⁺ and Fe³⁺ ions as well as humic acid and silica colloids) on CPE has been investigated. According to the experimental results the total method efficiency is (13 ± 2)% and the chemical recovery (50 ± 10)% at pH 4 and reactant ratio (V(TBP)/V(Triton) = 0.1). Regarding the other parameters, generally Ca²⁺ and Fe³⁺ ions as well as the presence of colloidal species in solution (even at low concentrations) results in significant decrease of the chemical recovery of uranium. On the other hand increasing NaCl concentration leads to enhancement of chemical recovery. The detection limit under optimum experimental conditions has been found to be 0.5 Bq L^?1 indicating that the method could be applied only to waters samples with increased uranium concentration. Moreover, the negative effect of the chemical species found in natural waters limits the applicability of the method with the respect to environmental radioactivity measurements.     

A modified method for the sequential determination of 210Po and 210Pb in Ca-rich material using liquid scintillation counting

This research describes methods for the sequential determination of ²¹⁰Pb and ²¹⁰Po activity concentrations in Ca-rich ash samples collected from oil shale-fired power plants in Estonia. The procedure involves digestion of Ca-rich ash samples in a microwave digestion system, radiochemical separation of ²¹⁰Pb and ²¹⁰Po and their measurements. All samples, blanks and standards were measured by liquid scintillation counting (Quantulus 1220). The method was tested using IAEA (International Atomic Energy Agency) RGU-1 and IAEA-444 reference materials. Spectral calibration/peak identification which included the optimization of α/β discrimination system (pulse shape analyser), and recovery have been made by ²⁰⁹Po and ²¹⁰Pb standard solutions.

     

Separation of the radioelements210Pb−210Bi−210Po by spontaneous deposition onto noble metals and verification by Cherenkov and liquid scintillation counting

A method for the separation of²¹⁰Pb,²¹⁰Bi and²¹⁰Po using spontaneous deposition has been developed. The²¹⁰Bi and²¹⁰Po are simultaneously removed by deposition onto nickel foil (copper and tin could also be used but less effectively) while the²¹⁰Po is separated from²¹⁰Bi, after dissolution of the nickel foil, by deposition onto silver foil. The effectiveness of each separation was evaluated by adding aliquot portions of each solution to a cocktail and counting with a liquid scintillation counter. Water was used as the medium to observe the Cherenkov count of the sample solution.     

Determination of 210Pb in environmental samples

Summary Measurement of ²¹⁰Pb has gained a highly scientific attention due to its wide range of environmental applications. The most commonly used analytical techniques: gamma-spectrometry, beta-counting and alpha-spectrometry were used to measure environmental samples (geological, soil, sediment). Our paper is aiming at comparing the capabilities and limits of application of these three different analytical techniques for ²¹⁰Pb measurement in various environmental samples. In addition, analytical data of ²¹⁰Pb measurements with the three different techniques (gamma-spectrometry, beta-counting and alpha-spectrometry) are discussed to highlight the degree of comparability and the most probable sources of discrepancies and errors. Based on the demanded investigation, one analytical technique will be chosen for routine analysis, while the other techniques, if they are available, could be used for analytical quality assurance measures. It was essential to compare the analytical efficacy of each technique, which differ concerning the detection limit (MDA), sensitivity, analytical effort, the duration of analysis and waiting time before analysis.     

A bone ash standard for90Sr,210Pb,210Po,uranium and the actinides

Possibilities and problems of experimental differentiation of two chemical or particle forms of element M (Acentral atom or group, Bcomplex, metalorganic or bioinorganic species, colloid, etc.) between which mutual equilibria can exist at their partition in two-phase systems, when the gross (analytical) concentrations are determined in each phase (by AAS, NAA, or radiometrically) are outlined for: (1) static distribution (batch separation) between two immiscible phases, when both the partial concentrations of A and B and their distribution coefficients generally can be determined by a single or fractional separation, (2) dynamic distribution (chromatographic separation) between the peaks of two metal species, when the potentialities can be strongly affected by secondary equilibria or when the sample-eluent interactions can be assessed.     

Thorium determination in water samples by liquid scintillation counting after its separation by cloud point extraction

The aim of this study is the separation and pre-concentration of thorium from aqueous solutions by cloud point extraction (CPE) and its the radiometric determination by liquid scintillation counting (LSC). For CPE, tributyl phosphate (TBP) was used as the complexing agent and (1,1,3,3-Tetramethylbutyl)phenyl-polyethylene glycol (Triton X-114) as the surfactant. The radiometric measurements were performed after phase separation by mixing of the surfactant phase with the liquid scintillation cocktail. The effect of experimental conditions such as pH, ionic strength (e.g. [NaCl]) and the presence of other chemical species (e.g. Ca²⁺ and Fe³⁺ ions, and humic acid colloids) on the CPE separation recovery have been investigated at constant reactant ratio (m(TBP)/m(Triton) = 0.1). According to the experimental results the maximum chemical recovery is (60 ± 5)% at pH 3. Regarding the other parameters, generally Ca²⁺ and Fe³⁺ ions as well as the presence of colloidal species in solution (even at low concentrations) results in significant decrease of the chemical recovery of uranium. On the other hand increasing NaCl concentration leads to enhancement of chemical recovery. Generally, the method could be applied successfully for the radiometric determination of thorium in water solutions with relatively increased thorium content.     

Simultaneous determination of210Bi and210Po on pine needles by solvent extraction and liquid scintillation counting

A determination procedure has been developed for²¹⁰Bi and²¹⁰Po in environmental samples and was applied for pine needles. Bismuth-210 and²¹⁰Po separated from the parent nuclide²¹⁰Pb as BiOCl precipitate were extracted simultaneously by TOPO/toluene containing PPO and POPOP. The separation of²¹⁰Bi and²¹⁰Po from²¹⁰Pb was almost satisfactory. The activity of²¹⁰Bi+²¹⁰Po in the TOPO/toluene was measured periodically by liquid scintillation counting for about 20 days after separation. The time course of the decreasing pattern of the activity was determined by the initial activity ratio²¹⁰Po/²¹⁰Bi. The decreasing pattern of the activity was compared with theoretical patterns, and best estimates for²¹⁰Po and²¹⁰Bi were obtained by non-linear least-squares fitting. The activities of²¹⁰Bi and²¹⁰Po were determined for one-year and two-year old pine needles fro the same pine tree, and weathering half-time and deposition rate of these nuclides was discussed.     

Modified 2-window approach for rapid determination of 90Sr and 90Y at low quench level using liquid scintillation counting

⁹⁰Sr is a product of nuclear fission, the radioactivity of which can be determined by liquid scintillation counting (LSC). Because the LSC spectra of ⁹⁰Sr and its daughter ⁹⁰Y overlap each other, the following methods are usually used: (1) measuring immediately after ⁹⁰Sr/⁹⁰Y separation; (2) waiting to reach radioactive equilibrium; (3) adopting the conventional 2-window approach; and (4) using the spectra deconvolution technique. The first one requires ⁹⁰Sr/⁹⁰Y separation and immediate measurement; the second one is time-consuming; the third one is valid only for samples with the same quench level as the calibration standard; the last one is somewhat complicated, and in some cases it is not convenient to export the experimental data to some deconvolution software. Therefore, we have developed a modified 2-window approach to rapidly determine ⁹⁰Sr and ⁹⁰Y in either equilibrium or disequilibrium at low quench level. The key modification of the approach is to provide an LSC spectrum of pure ⁹⁰Y with the same quench level as the sample to be determined. This modification eliminates the need to conduct ⁹⁰Sr/⁹⁰Y separation for the sample itself, to prepare the quench curves, and to fit the LSC spectra with some deconvolution software.     

Determination of 210Pb and 210Po in mineral and biological environmental samples

The paper deals with the determination of ²¹⁰ Pb and ²¹⁰ Po in mineral and biological environmental samples. ²¹⁰ Pb and ²¹⁰ Po were preconcentrated from filtered water samples by coprecipitation with iron(III) hydroxide at pH 9-10 using ammonia solution and the precipitate was dissolved with HCl and mineralized with H2O2. ²¹⁰ Pb and ²¹⁰ Po in soil or sediment, algae and mussel samples were sequentially leached out at 250 °C with HNO₃ +HF, HClO₄ and HCl. About 10-20% of the leaching solution was used for ²¹⁰ Po determination which was carried out at 85-90 °C for 4 hours by suspending a silver disk in a HCl solution of pH 1.5 and containing some hydroxylamine hydrochloride and sodium citrate. No preliminary separation was required and essentially quantitative recoveries were obtained by using standard ²⁰⁹ Po tracer. The remains of the leaching solution were used for the determination of ²¹⁰ Pb which was first separated by a BIO-RAD-AG 1-X4 resin column, then purified by using Na2S to precipitate as PbS and finally precipitated as PbSO₄ for source preparation. Starting from 3 g sediment (30 liter water), the lower limits of detection of the method were 0.73 Bq.kg^-1 (0.078 mBq.l^-1 ) for ²¹⁰ Pb and 0.25 Bq.kg^-1 (0.016 mBq.l^-1 ) for ²¹⁰ Po. The procedure has been checked with two certified samples supplied by the International Atomic Energy Agency (IAEA) and reliable results were obtained. Most of the analyzed samples were sediments, showing average yields of 84.2±5.2% for ²¹⁰ Pb and 96.4±4.1% for ²¹⁰ Po.     

Urine strontium-90 (Sr-90) manual and automated pre-analytical separation followed by liquid scintillation counting

Journal of Radioanalytical and Nuclear Chemistry - Responding to a radiological or nuclear incident may require assessing tens to hundreds of thousands of people for possible radionuclide...