Certified reference material for radionuclides in seawater IAEA-381 (Irish Sea Water)

A certified reference material (CRM) for radionuclides in seawater, IAEA-381 (Irish Sea Water), is described and the results of certification are presented. The material has been certified for nine radionuclides (⁴⁰K, ⁹⁰Sr, ¹³⁷Cs, ²³⁷Np, ²³⁸Pu, ²³⁹Pu,²⁴⁰Pu, ^239,240Pu and ²⁴¹Am). Information on massic activities with the corresponding 95% confidence intervals are given for eight radionuclides (³H, ¹²⁵Sb, ²³⁴U, ²³⁵U, ²³⁶U, ²³⁸U, ²⁴¹Pu and ²⁴⁴Cm). Less reported radionuclides include ⁶⁰Co, ⁹⁹Tc, and ²⁴²Pu. The CRM may be used for quality assurance/quality control of the analysis of radionuclides in environmental water samples, for the development and validation of analytical methods and for training purposes. The material is available from the IAEA in 5 kg units.     

A new reference material for radionuclides in the mussel sample from the Mediterranean Sea (IAEA-437)

A new Reference Material (RM) for radionuclides in mussel (Mytilus galloprovincialis) from the Mediterranean Sea (IAEA-437) is described and the results of the certification process are presented. Four radionuclides (⁴⁰K, ²³⁴U, ²³⁸U, and ^239+240Pu) have been certified, and information values on massic activities with 95% confidence intervals are given for nine radionuclides (¹³⁷Cs, ²¹⁰Pb(²¹⁰Po), ²²⁶Ra, ²²⁸Ra, ²²⁸Th, ²³⁰Th, ²³²Th, ²³⁵U, and ²⁴¹Am). Results for less frequently reported radionuclides (⁹⁰Sr, ¹²⁹I, ²³⁸Pu, ²³⁹Pu, and ²⁴⁰Pu) are also reported. The RM can be used for quality assurance/quality control of the analysis of radionuclides in mussel samples, for the development and validation of analytical methods and for training purposes. The material is available in 200 g units.     

New measurement of <Superscript>129</Superscript>I in IAEA-375 reference material

Summary Under an IAEA project for upgrading of reference materials, a new determination of the ¹²⁹I concentration in the IAEA-375 reference material was performed. A chemical procedure was set up for the preparation of the AgI samples. Measurement of ¹²⁹I was carried out using the IsoTrace Tandetron AMS facility at University of Toronto. To ensure the accuracy of the calibration, the tuning of the AMS system was iterated using not only the QC (quality control) samples but also all unknown samples. To minimize any possible current-dependent effects between ¹²⁹I and ¹²⁷I ions in the injection magnet, low Cs⁺ sputtering beam intensity (10 μA) was used. The reproducibility in determining the ¹²⁹I/¹²⁷I ratio in the IAEA-375 AgI samples was less than 1%. The activity concentration (C_A) of ¹²⁹I in the IAEA-375 reference material was determined to be 1.59±0.08 mBq ^. kg^-1 at 95% confidence level. The present value is about 7% lower than the IAEA recommended value (1.7 mBq ^. kg^-1) listed in 2000 or 20% lower than the recommended value (2 mBq ^. kg^-1) listed in the IAEA AQCS Reference Material Catalogue (2002-2003). Since the IAEA recommended values for IAEA-375 materials was issued about 10 years ago and error range of the recommended values were large, the results we obtained might be useful in upgrading the recommended value.     

A certified reference material for radionuclides in the water sample from Irish Sea (IAEA-443)

A new certified reference material (CRM) for radionuclides in sea water from the Irish sea (IAEA-443) is described and the results of the certification process are presented. Ten radionuclides (³H, ⁴⁰K, ⁹⁰Sr, ¹³⁷Cs, ²³⁴U, ²³⁵U, ²³⁸U, ²³⁸Pu, ^239+240Pu and ²⁴¹Am) have been certified, and information values on massic activities with 95% confidence intervals are given for four radionuclides (²³⁰Th, ²³²Th, ²³⁹Pu and ²⁴⁰Pu). Results for less frequently reported radionuclides (⁹⁹Tc, ²²⁸Th, ²³⁷Np and ²⁴¹Pu) are also reported. The CRM can be used for quality assurance/quality control of the analysis of radionuclides in water samples, for the development and validation of analytical methods and for training purposes. The material is available in 5 L units from IAEA (http://nucleus.iaea.org/rpst/index.htm).     

Radioactive 129I in surface water of the Celtic Sea

Relatively large amounts of radioactive iodine ¹²⁹I (T _1/2  = 15.7 Ma) have been documented in seawater such as the English Channel, the Irish Sea and the North Sea. Data on the concentration of the iodine isotopes in waters of the Celtic Sea are missing. Aiming to provide first ¹²⁹I data in the Celtic Sea and compare them with levels in the other close-by seawater bodies, surface seawater samples were analyzed for the determination of ¹²⁷I and ¹²⁹I concentrations. The results revealed a high level of ¹²⁹I in these waters and suggest strong influence by liquid discharges from La Hague and Sellafield reprocessing facilities. ¹²⁷I concentrations are rather constant while the ¹²⁹I/¹²⁷I ratio reaches up to 2.8 × 10^?8 (ranging from 10^?10 to 10^?8), which is 2–4 orders of magnitude higher than pre-nuclear era natural level. Transport of ¹²⁹I to the Celtic Sea is difficult to depict accurately since available data are sparse. Most likely, however, that discharges originated from La Hague may have more influence on the Celtic Sea ¹²⁹I concentrations than the Sellafield. Comprehensive surface water and depth profiles ¹²⁹I data will be needed in the future for assessment of environmental impact in the region.     

Neutron activation analysis of IAEA proposed certified reference material IAEA-407 (North Sea Fish Homogenate)

The proposed reference material from the International Atomic Energy Agency, namely IAEA-407 (Fish Homogenate) was analyzed using instrumental neutron activation analysis (INAA). 15 elements, Al, As, Cl, Co, Cr, Fe, Hg, Mg, Mn, K, Na, Sb, Se, V and Zn, were determined using two irradiations (5 minutes and 5 hours) and four countings. IAEA-MA-A-1/TM (Copepoda Homogenate), NIST-SRM-1566 (Oyster Tissue), NIST-SRM-1572 (Citrus Leaves) and NIST-SRM-1577a (Bovine Liver) were utilized as standards in the quantification step.     

Working Methods Paper: Certification of methylmercury compounds concentration in marine sediment reference material,IAEA-356

An intercomparison exercise was organized between seven laboratories using various isolation procedures (extraction, distillation, ion-exchange and alkaline digestion) and detection systems (CV AAS, cold vapour atomic absorption spectroscopy; CV AFS, cold vapour atomic fluorescence spectroscopy; GC, ECD, gas chromatography electron capture detector and HPLC with CV AFS detection) for determination of methylmercury compounds in sediment sample. All certification criteria were fulfilled and therefore the value for total concentration of methylmercury compounds was certified to be 5.46 ng g^?1, with a 95% confidence interval from 4.07–5.84 ng g^?1. The acceptable range, calculated as two times the confidence interval of the mean is therefore from 4.68–6.23 ng g^?1. This is the first sediment reference material ever to be certified for concentration of methylmercury compounds. Comparison of the data obtained by various methodologies has shown that the most critical step is the isolation of methylmercury compounds from binding sites. Acid leaching only cannot release methylmercury compounds quantitatively. Total release of methylmercury compounds could only be achieved by alkaline digestion or distillation. This simple intercomparison exercise has shown that since large numbers of laboratories world-wide are performing methylmercury compound analyses using various improved and specific separation methods and sensitive detection systems, certification of methylmercury compounds in different biological and environmental samples should not be a problem in the future.     

A systematic study on the extractability of arsenic species from algal certified reference material IAEA-140/TM (Fucus sp., Sea Plant Homogenate) using methanol/water extractant mixtures

Using methanol/water mixtures (from pure water to pure methanol), with different desorption and solubility parameters, and varying extractant volume to algal mass (V/m) ratios, the extractability of arsenic species from CRM IAEA-140/TM was investigated. A linear sorption isotherm-based model was developed to process the data obtained with variable volume extraction, allowing the unambiguous deduction of the maximal extractable species concentrations under the specific extraction conditions, even for more stable species.The maximal extractable arsenic fraction ranged from 41 to 68% of the total arsenic concentration in CRM IAEA-140/TM, depending on the extractant composition, with pure methanol giving the lowest extraction yield and pure water giving erratic extractability (probably due to bad wettability). The main arsenic species quantified in the methanol/water extracts were arsenosugars, with arsenosugars 1 (glycerol arsenosugar), 3 (sulfonate arsenosugar) and 4 (sulfate arsenosugar) making up ca. 90% of the maximal extractable arsenic. The rest accounts for DMA (dimethylarsinate), arsenosugar 2 (phosphate arsenosugar) and As(V). There is no clear extraction pattern emerging from the data although it may be seen that extraction of more polar species (e.g. arsenosugar 1) is favoured in pure methanol and less polar more ionic species (e.g. arsenosugar 2 and As(V)) in methanol extractants with a higher water percentage.The precise and highly accurate data may be used for quality control purposes under strictly followed extraction conditions since the extraction is operationally defined. Additionally, the variable volume extraction methodology presented may be applied to other elemental species in other matrices using other extractants. Although this approach does not maximise the absolute extractability but only that which is extractant-specific, experimentators are forewarned that in most cases only a fingerprint of the extractant-specific species is produced unless a quantitative extraction of all species is obtained.     

Depth profiles of 129I species in the Bothnian Sea

The Bothnian Sea which is located between Finland and Sweden represents an important source of fresh water to the Baltic Sea. We here present new data on the radioactive isotope ¹²⁹I species from water samples collected in December 2009 at different depths in the Bothnian Sea. Concentrations of ¹²⁹I^? (iodide) in the Bothnian Sea range from 14 × 10⁸ to 32 × 10⁸ atoms/L, while ¹²⁹IO₃ ^? (iodate) concentrations are relatively low and fluctuating at 1 × 10⁸ atoms/L. For nutrients data determined in the same samples as ¹²⁹I, significant correlations could be found between ¹²⁹I^? and total P, NO₃–N, SiO₃–Si, but rather poor with NH₄–N. The correlations suggest comparable source pathway of ¹²⁹I^? and nutrient parameters, while the source of NH₄–N may be different. The small amounts and negligible change of ¹²⁹IO₃ ^? indicate prevailing extensive reduction of iodate in the Baltic Sea.     

Certification of total mercury and methylmercury concentrations in mussel homogenate (Mytilus edulis) reference material, IAEA-142

Due to the increased demand for new reference materials certified for total and methylmercury (MeHg) a sample of mussel homogenate (IAEA-142) has been prepared. Thirteen experienced laboratories reported results for total Hg of which 9 laboratories also reported results for MeHg content. Laboratories reporting MeHg results used various isolation techniques (solvent extraction, saponification, acid leaching, ion-exchange separation, and distillation) and detection systems (cold vapour atomic absorption spectrometry (CV AAS), cold vapour atomic fluorescence spectrometry (CV AFS), gas chromatography with electron capture detector (GC/ECD) and HPLC with CV AAS detector). In the case of total Hg, most of the laboratories used acid digestion, only two used alkaline dissolution, followed either by CV AAS or CV AFS. One laboratory used neutron activation analyses with radiochemical separation. The data received were in good agreement. The value for total Hg was certified to be 126 ng/g, with a 95% confidence interval from 119 to 132 ng/g. For MeHg the certified value of 47 ng/g expressed as Hg was assigned, with a 95% confidence interval from 43 to 51 ng/g. Stability testing has shown that both total and MeHg are stable if samples are stored in a dry and dark place at room temperature. The sample is now available as a certified reference material and is, in particular, useful for quality control measurements of Hg and MeHg in mussel samples at low concentration levels. Received: 24 September 1996 / Revised: 20 November 1996 / Accepted: 8 December 1996     

Certification of total mercury and methylmercury concentrations in mussel homogenate (Mytilus edulis) reference material, IAEA-142

Due to the increased demand for new reference materials certified for total and methylmercury (MeHg) a sample of mussel homogenate (IAEA-142) has been prepared. Thirteen experienced laboratories reported results for total Hg of which 9 laboratories also reported results for MeHg content. Laboratories reporting MeHg results used various isolation techniques (solvent extraction, saponification, acid leaching, ion-exchange separation, and distillation) and detection systems (cold vapour atomic absorption spectrometry (CV AAS), cold vapour atomic fluorescence spectrometry (CV AFS), gas chromatography with electron capture detector (GC/ECD) and HPLC with CV AAS detector). In the case of total Hg, most of the laboratories used acid digestion, only two used alkaline dissolution, followed either by CV AAS or CV AFS. One laboratory used neutron activation analyses with radiochemical separation. The data received were in good agreement. The value for total Hg was certified to be 126 ng/g, with a 95% confidence interval from 119 to 132 ng/g. For MeHg the certified value of 47 ng/g expressed as Hg was assigned, with a 95% confidence interval from 43 to 51 ng/g. Stability testing has shown that both total and MeHg are stable if samples are stored in a dry and dark place at room temperature. The sample is now available as a certified reference material and is, in particular, useful for quality control measurements of Hg and MeHg in mussel samples at low concentration levels.     

水中氯离子溶液标准物质的研制

以氯化钠纯度标准物质为原料,超纯水为溶剂,采用重量–容量法制备了水中氯离子溶液标准物质,系统阐述了水中氯离子溶液标准物质的研制方法.采用离子色谱法对制备的水中氯离子溶液标准物质进行分析,通过F–检验和回归曲线法对色谱数据进行计算,方差分析和线性拟合结果表明该溶液标准物质具有良好的均匀性和稳定性.研制的水中氯离子溶液标准...     

Certified reference material for the quality control of cadmium,copper nickel and zinc determination in estuarine water (CRM 505)

Analyses of estuarine water samples are routinely carried out by a number of laboratories to monitor the level of environmental contamination by toxic substances, e.g. heavy metals. A series of interlaboratory studies has been organised by the Community Bureau of Reference, BCR (now renamed Standards, Measurements and Testing Programme) to improve the quality of the determinations of selected trace metals in estuarine water samples. The improvement achieved allowed to produce a reference material (CRM 505) which was certified for its content of Cd, Cu, Ni and Zn. Further improvements were considered to be necessary for the certification of other trace elements, e.g. Pb. This material was collected in the Tagus Estuary, carefully prepared (filtered and acidified) and its homogeneity and long term stability were verified. This paper presents the work performed for the certification of Cd, Cu, Ni and Zn. Indicative values are reported for As, Co, Fe, Mn, Pb and V.     

Certified reference material for the quality control of cadmium, copper nickel and zinc determination in estuarine water (CRM 505)

Analyses of estuarine water samples are routinely carried out by a number of laboratories to monitor the level of environmental contamination by toxic substances, e.g. heavy metals. A series of interlaboratory studies has been organised by the Community Bureau of Reference, BCR (now renamed Standards, Measurements and Testing Programme) to improve the quality of the determinations of selected trace metals in estuarine water samples. The improvement achieved allowed to produce a reference material (CRM 505) which was certified for its content of Cd, Cu, Ni and Zn. Further improvements were considered to be necessary for the certification of other trace elements, e.g. Pb. This material was collected in the Tagus Estuary, carefully prepared (filtered and acidified) and its homogeneity and long term stability were verified. This paper presents the work performed for the certification of Cd, Cu, Ni and Zn. Indicative values are reported for As, Co, Fe, Mn, Pb and V.     

Certification of trace and major elements and methylmercury concentrations in a macroalgae (Fucus sp.) reference material, IAEA-140

A marine reference material, IAEA-140, prepared with a macroalgae (Fucus sp.) was recently produced by the International Atomic Energy Agency and certified for trace and major elements and for methylmercury (MeHg). Certification of this material was achieved as an outcome of an international analytical intercomparison study which resulted in 116 independent sets of results reported by participants from 54 countries. The statistical evaluation of the collected data and the criteria used for assignment of the mean and uncertainty values are described. The analysis of data allowed to certify concentration values for 24 elements and MeHg, and to provide information values for another 10 elements. Regarding the elements which could be given certified values, between two and eight different instrumental methods were used to measure metal concentrations, and four independent analytical procedures were used to measure MeHg concentrations. In order to assess the results of the certification procedure, a comparison was made between the certified values obtained from the world-wide intercomparison results and the values obtained from a small subgroup of well-qualified laboratories. The means and 95% confidence intervals for reference values obtained by the two methods are similar for most elements showing that the usual method of certification used by the IAEA, based on large groups of participants, is indeed pertinent.     

Certification of trace and major elements and methylmercury concentrations in a macroalgae (Fucus sp.) reference material, IAEA-140

A marine reference material, IAEA-140, prepared with a macroalgae (Fucus sp.) was recently produced by the International Atomic Energy Agency and certified for trace and major elements and for methylmercury (MeHg). Certification of this material was achieved as an outcome of an international analytical intercomparison study which resulted in 116 independent sets of results reported by participants from 54 countries. The statistical evaluation of the collected data and the criteria used for assignment of the mean and uncertainty values are described. The analysis of data allowed to certify concentration values for 24 elements and MeHg, and to provide information values for another 10 elements. Regarding the elements which could be given certified values, between two and eight different instrumental methods were used to measure metal concentrations, and four independent analytical procedures were used to measure MeHg concentrations. In order to assess the results of the certification procedure, a comparison was made between the certified values obtained from the world-wide intercomparison results and the values obtained from a small subgroup of well-qualified laboratories. The means and 95% confidence intervals for reference values obtained by the two methods are similar for most elements showing that the usual method of certification used by the IAEA, based on large groups of participants, is indeed pertinent.     

Certified reference material (CRM 414) for the quality control of trace element analysis in plankton

Summary Analyses of plankton are performed by a number of organisations to investigate the transfer and uptake of toxic elements along the trophic chain and to monitor the levels of contamination of different aquatic environments. In order to obtain reliable transfer functions in environmental models or to use plankton as an indicator organism for the assessment of environmental pollution, these analyses should give accurate results. As accuracy requires quality control and the application of certified reference materials (CRMs), a certification campaign has been conducted by the Community Bureau of Reference (BCR). A plankton material was collected in a freshwater pond, lyophilised, homogenised and bottled and its homogeneity and long-term stability were verified. The material (CRM 414) was analysed by a group of 15 selected laboratories having given proof of their adequate QC and using different analytical methods. The contents of As, Cd, Cr, Cu, Hg, Mn, Ni, Pb, Se, V and Zn are certified. This paper presents the certification work performed.     

Certified reference material for quantification of polycyclic aromatic hydrocarbons in sediment from the National Metrology Institute of Japan

The National Metrology Institute of Japan has issued a certified reference material (CRM) of freshwater lake sediment for polycyclic aromatic hydrocarbon (PAHs) analyses. The certification used three extraction techniques: pressurized liquid extraction (PLE) with toluene, PLE with dichloromethane/ethyl acetate (1:1 by volume), and alkaline extraction (1 M KOH in methanol) in combination with microwave-assisted extraction. Both gas chromatography/mass spectrometry (GC/MS) and liquid chromatography/dopant-assisted atmospheric pressure photoionization/MS (LC/DA-APPI/MS) analyses were used. Certified values are provided for 18 PAHs at 1–25 μg kg⁻¹ except for perylene (2.08 × 10³ μg kg⁻¹), and information values are provided for two. Since the values of PAHs in the CRM are much lower than those in other CRMs and are comparable to those found at sites with little human influence, the CRM is suitable for PAH monitoring in sediment and soil samples.