交联阳离子淀粉的制备及其脱色性能

在碱催化剂6％氢氧化锂水溶液存在下,以N－（2,3－环氧丙基）三甲基氯化铵（GTA）为阳离子化试剂,制备了交联高取代度季铵型阳离子淀粉。考察了6％氢氧化锂水溶液、水含量、反应温度和反应时间对取代度和反应效率的影响。当淀粉用量为5．8g,GTA用量为3．0g时,最佳反应条件为：6％氢氧化锂水溶液2．0g、反应温度70℃、反应时间2h、反应体系含水量24．6％。在此条件下,取代度可达0．5,反应效率为83．3％。对制得阳离子淀粉的脱色性能研究结果表明,交联取代度阳离子淀粉对活性染料具有优异的脱色效果。当投加量为105mg/L时,对质量浓度为100mg/L活性红X－3B、活性黄KN－6G、活性蓝X－BR溶液的脱色率分别为99．1％、88．0％、95．5％。     

阳离子淀粉吸附脱色性能的研究

本文对阳离子淀粉(CST)的吸附性能进行了系统的研究。实验表明阳离子淀粉对各种阴离子染料的吸附,主要是化学吸附。在pH为2～8范围内和室温下,对不同结构的阴离子染料均有一定吸附脱色效果。     

机械活化木薯淀粉氧化产物的结构表征

采用搅拌球磨机对木薯淀粉进行机械活化,以活化60min的木薯淀粉为原料,CuSO4为催化剂,H2O2为氧化剂干法制备氧化淀粉。利用红外光谱、扫描电子显微镜、X-射线衍射等手段对产物的结构进行表征分析,并与原淀粉的氧化产物进行比较。结果表明,机械活化对木薯淀粉的氧化反应有显著的影响。原木薯淀粉的氧化反应主要发生在淀粉颗粒的表面及无定形区,部分发生在结晶区,产物是无定形及结晶状态的结构;活化淀粉的氧化反应在淀粉团粒表面及内部均匀进行,产物是无定形的聚集状态结构。并就机械活化对淀粉氧化的强化机理进行了探讨。     

三氯化铝催化合成阳离子淀粉

以淀粉和三甲基环氧丙基氯化铵为原料,在三氯化铝催化作用下,制备了阳离子淀粉,最佳反应条件为:淀粉 50g,三甲基环氧丙基氯化铵 10g,三氯化铝 0. 74g, 50%乙醇 60mL,反应温度 50℃,反应时间 17h.     

淀粉基阳离子絮凝剂的研制及性能测试

用可溶性淀粉为原料,通过接枝改性合成了一种淀粉基阳离子絮凝剂(MSF),其最佳制备工艺条件为:淀粉与丙烯酰胺的质量比为1:2,引发剂用量为0.6 g,反应温度为50 ℃,接枝时间为3.5 h;阳离子化条件为:甲醛和二甲胺摩尔比为1.0:1.4,反应时间2.5 h,反应温度50 ℃.产物结构经FTIR证实.用其处理番茄废水后,废水的透光率提高了78.2%、TOC下降了22.5%、COD下降了37.25%,结果表明该产品对高浓度有机废水的絮凝性能优于聚丙烯酰胺高分子絮凝剂(PAM).     

2,5-二羟基对苯二甲酸结构与性能表征

针对目前国内外关于2,5-二羟基对苯二甲酸(DHTA)的研究报道较少,结构性能表征信息分散等现状,自制DHTA,并通过UV、FT-IR、MS、1H-NMR、13C-NMR和STA-FTIR等方法对其进行了较全面的结构与热性能表征技术研究.     

淀粉基强阳离子两性絮凝剂的合成

淀粉基强阳离子两性絮凝剂的合成;淀粉; 阳离子; 两性絮凝剂     

醋酸酯淀粉的溶解性能、形貌与XRD结构分析

淀粉是一种多糖类天然高分子,来源广泛,价格低廉,可生物降解并且降解产物环境友好。但天然淀粉脂溶性差、颗粒大、稳定性差、加工成型及使用受限。当分子中的羟基被亲脂基团取代后,淀粉原有的氢键将被破坏而使其脂溶性增强,同时原有的结晶区被破坏而引起淀粉聚集状态变化、颗粒尺寸减小、热稳定性增强。乙酰基是比较     

水发泡淀粉挤出泡沫的结构与性能

以水为发泡剂,普通玉米淀粉为原料,采用双螺杆挤出机制备淀粉泡沫材料,研究了发泡剂用量及聚乙烯醇的加入量对泡沫材料结构与性能的影响。 用扫描电子显微镜观察了泡沫材料截面的形态,用万能材料试验机测试了泡沫材料的力学性能。 结果表明,水的质量分数为8%时淀粉泡沫径向膨胀率和发泡倍率最高,分别为22倍和17.6倍,压缩模量最高（4.07 MPa）。 加入质量分数10%的聚乙烯醇(PVA)使淀粉泡沫的孔径变大至1.29 mm,壁厚增加至82.43 μm,同时压缩模量增加至9.70 MPa。     

热塑性淀粉的制备及其结构与性能

热塑性淀粉的制备及其结构与性能;流变性能;生物降解     

导电聚合物的结构和性能表征方法

综述了导电聚合物的结构与性能表征的几种经典和现代的仪器方法，指出了这些方法的特点及用途。     

Raman Spectroscopic Determination of the Degree of Cationic Modification in Waxy Maize Starches

ABSTRACT

Waxy (essentially amylose-free) maize starch was chemically modified to varying degrees by treatment with 3-chloro-2-hydroxypropyltrimethyl ammonium chloride (CHPTAC), and the degree of cationic modification was determined by a standard wet chemistry method. FT-Raman spectra of the modified starches were taken, and a characteristic Raman band ～761 cm^?1 was found. This 761 cm^?1 Raman band's intensity depended on the level of cationic modification of the starch. The ratio of intensity of the ～761 cm^?1 band to a ～715 cm^?1 C-C stretch Raman band (used as an internal standard) was plotted versus the amount of cationic modification derived by titration analysis, and a linear fit was obtained with a correlation of 0.998. The FT-Raman spectroscopy method presented here demonstrates a rapid non-destructive way to determine the level of cationic modification of waxy maize starch, and should be suitable for use with cationic modified starches of any amylose content.     

Structure and Processing Properties of Nine Yam (Dioscorea opposita Thunb) Starches from South China: A Comparison Study

In order to explore the processing and application potential of Chinese yam starch, nine kinds of Chinese yam starch (GY11, GY5, GY2, GXPY, LCY, SFY, MPY, SYPY, ASY) from South China were collected and characterized. The chemical composition, rheological properties, thermal properties, and in vitro starch digestion were compared, and the correlation between the structure and processing properties of these yam starches was analyzed using Pearson correlation. The results show that GY2 had the highest amylose content of 28.70%. All the yam starches were similarly elliptical, and all the yam starch gels showed pseudoplastic behavior. Yam starches showed similar pasting temperatures and resistant starch content, but SYPY showed the largest particle size (28.4 μm), SFY showed the highest setback (2712.33 cp), and LCY showed the highest peak viscosity (6145.67 cp) and breakdown (2672.33 cp). In addition, these yam starches also showed different crystal types (A-type, B-type, C-type), relative crystallinity (26.54–31.48%), the ratios of 1045/1022 cm⁻¹ (0.836–1.213), pasting properties, and rheological properties, so the yam starches have different application potentials. The rheological and pasting properties were related to the structural properties of starch, such as DI, Mw, and particle size, and were also closely related to the thermodynamic properties. The appropriate processing methods and purposes of the processed products of these yam starches can be selected according to their characteristics.     

粒径可控阳离子型聚苯乙烯纳米粒子的制备及表征

在采用阳离子型双子（gemini）表面活性剂作为乳化剂,不使用任何助乳化剂的条件下,通过改进微乳液聚合工艺制备了窄分布粒径可控的阳离子型聚苯乙烯（PS）纳米乳液。 改进微乳液聚合的主要特点是：大部分苯乙烯以预乳液的形式恒速滴入引发聚合的微乳液中,使用具有高乳化性能的gemini表面活性剂作为乳化剂能明显降低乳胶粒粒径。 实验结果表明,少量阳离子单体三甲基烯丙基氯化铵作为共聚单体能够明显减小Z均粒径、降低粒度分布,乳化剂用量、引发剂用量和反应温度均能影响制备乳胶粒的粒径及其粒度分布。 乳化剂和引发剂用量分别为苯乙烯质量的5%~10%和1.0%~1.5%、反应温度为70~75 ℃时,能够制备粒径小分布窄的阳离子型聚苯乙烯纳米粒子。 Z均粒径与苯乙烯质量之间的线性关系表明,Z均粒径可以通过苯乙烯用量来控制。 不同聚合工艺下制备的聚合物粒度分布曲线表明,改进微乳液聚合工艺（半连续预乳化工艺）在制备窄分布的聚合物纳米粒子方面具有很强的优越性。     

Synthesis and Characterization of Yttrium Doped Nano-zirconia by a Cationic Surfactant-assisted Route

1INTRODUCTION Zirconia is a kind of metal oxide material with high melting point(2700℃),high boiling point,small thermal conductivity,large coefficient of ther-mal expansion,high temperature resistance,good abrasive resistance and favorable resistance to corrosion.Due to its both acid and alkaline surface centers,zirconia is an ideal catalytic material with acid group bi-functions[1].In addition,owing to the excellent ionic exchange property as well as the chemical and mechanical stabilit…     

小粒径无皂阳离子PMMA胶乳粒子的制备与表征

采用溶剂热法,以AIBA为引发剂制得小粒径无皂阳离子PMMA胶乳纳米粒子。讨论了单体用量、引发剂用量和反应温度对胶乳粒径及乳液的粒径分布的影响;用^1H—NMR、TEM、FTIR、GPC、DTA等对聚合物进行了表征。结果表明：采用溶剂热法制得的无皂阳离子胶乳粒子粒径约为35nm,分散均匀;随着温度的升高,粒径逐渐减小;间同、无规、全同立构的相对含量分别为：55．3％、37．8％、6．9％;乳液的抗电解质稳定性好。     

The Synthesis,Characterization, and Photoinitiated Cationic Polymerizaton of Difunctional Oxetanes

Abstract

Seven novel difunctional oxetane monomers have been prepared and characterized using standard spectroscopic techniques. The photoinitiated cationic polymerization of these seven monomers was carried out and their reactivity compared to a typical diepoxide monomer. In these studies the reactivities of the various oxetane monomers were evaluated and compared by three different techniques: gel time measurements, differential scanning photocalorimetry, and real time infrared spectroscopy. It was observed that the difunctional oxetanes are generally more reactive than their structurally similar epoxide counterparts in photoinitiated cationic polymerization.     

新型可聚合双季铵盐阳离子表面活性剂的合成与表征

合成了新型可聚合的单季铵盐阳离子表面活性剂(PMQ)和双季铵盐阳离子表面活性剂(PDQ)。其结构经1HNMR和元素分析表征。在25℃的中性水溶液中PMQ和PDQ的临界胶束浓度分别为25.1mmol·L-1和32.4mmol·L-1,对应的表面张力分别为37.8mN·m-1和40.95mN·m-1。     

基于金纳米棒的核壳纳米结构及其光学性质研究

以金纳米棒为核的核壳结构纳米粒子由于它独特的光学性质、结构特点以及在催化、表面增强拉曼散射方面的应用前景,成为目前纳米材料研究的热点之一。本文重点介绍以金纳米棒为核,包覆其他无机材料的核/壳结构之合成方法,同时阐述其结构特征、光学性质以及外界条件对结构和性质的影响。其中,由于金银纳米核壳结构的研究开始最早,研究最为深入,故对其进行重点阐述。最后对以金纳米棒为核的核壳结构未来研究进行了展望。     

Hyperbranched Polymers in Cationic UV Curing

Summary: A wide range of hyperbranched polymers (HBP) was synthesized and investigated as additives in cationic photopolymerization of epoxy systems. The HBP were inserted into the polymeric network either by a copolymerization or through a chain transfer reaction involving the phenolic hydroxyl groups. By varying the type and concentration of HBP a modification of the bulk properties of photocured films was induced. An increase of toughness properties together with a flexibilization was obtained without affecting the processability and the viscosity of the photocurable mixture. In the presence of fluorine-containing HBP, a surface modification was induced.