茚虫威残留的气相色谱-质谱联用法测定

研究了用固相萃取(SPE)-选择离子(SIM) -气相色谱(GC) -质谱(MS)联用法测定蔬菜、水果中茚虫威残留的分析方法.样品采用乙腈超声波均质提取,固相萃取柱净化,丙酮定容.添加量为0.05 μg ～ 1.00μg时,回收率为86.5％ ～ 107.2％,相对标准偏差(RSD)＜5.0％,定量检出限为:0.001...     

血液中吲唑酰胺类合成大麻素的检验研究

建立了血液中6种吲唑酰胺类合成大麻素超高效液相色谱-串联质谱(UPLC-MS/MS)检验方法.前处理分别采用沉淀蛋白和固相萃取2种方法,UPLC-MS/MS检测,选用ACQUITY UPLC BEH C18(1.7 μm,2.1 mm ×100 mm)色谱柱,含1 mmol/L甲酸铵的甲酸-水(1∶1000,V∶V)溶液为水相(A相),甲醇为有机相(B相)进行梯度洗脱,采用正离子扫描模式,多反应监测(MRM)模式进行检测.结果 表明,6种合成大麻素的线性范围宽,相关系数均大于0.99,检出限0.01 ～0.05 ng/mL,定量限0.05 ～0.1 ng/mL,回收率77.1％ ～95.7％,基质效应在75.2％ ～ 104.4％,日内日间精密度均小于11％.建立的方法可用于真实血液样本的检验.     

顶空-固相微萃取-气相色谱法检测可可麦汁中吡嗪类化合物

建立了顶空-固相微萃取(HS-SPME)-气相色谱快速测定可可麦汁中3种吡嗪类物质(2,5-二甲基吡嗪、2,3,5-三甲基吡嗪和2,3,5,6-四甲基吡嗪)的方法.选择不同的固相微萃取头对萃取温度和时间进行优化,所得最佳萃取条件为:在60℃下,采用75 μm CAR/PDMS萃取头对麦汁样品萃取40 min.本方法的检出限(S/N=3)为0.023～ 0.056 μg/L,线性范围1～500 mg/L;相对标准偏差为3.6％～6.4％;回收率为95.4％～102.7％.本方法应用于样品检测,发现可可麦汁中吡嗪的浓度与原料中可可粉的添加量正相关,显示了很好灵敏性.     

在线凝胶渗透色谱-气相色谱-串联质谱非衍生化法测定食品中氯丙醇

建立了食品中氯丙醇类化合物的非衍生化在线凝胶渗透色谱-气相色谱-串联质谱(Online GPC-GCMS/MS)测定方法,目标化合物包括3-氯-1,2-丙二醇(3-MCPD)、2-氯-1,3-丙二醇(2-MCPD)、1,3-二氯-2-丙醇(1,3-DCP)和2,3-二氯-1-丙醇(2,3-DCP).样品中加入氘代同位素内标后,采用ExtrelutTM NT硅藻土进行固相支持液液萃取净化,用正己烷淋洗去除非极性杂质,以乙酸乙酯萃取目标物,萃取液经浓缩后直接采用Online GPC-GC-MS/MS测定.4种氯丙醇在0.005～1.000 mg/L范围内呈良好线性,相关系数均大于0.999,4种氯丙醇的检出限在0.002～ 0.005 mg/kg之间,定量限在0.005～0.01 mg/kg之间.以空白酱油样品为代表性基质的3个水平(0.02,0.1和0.5 mg/kg)的加标回收率和相对标准偏差(RSD,n=6)分别为94.8％～106.3％ (2.2％ ～ 10.3％),91.8％～108.8％(2.1％～10.6％)和83.1％ ～109.4％(1.3％～9.4％).采用本方法分别对酱油、水解植物蛋白液(粉)、料酒、鸡精、面包和糕点样品进行检测,均得到了满意的测定结果.     

Determination of Perfluorooctanoic Acid (PFOA) in Plastic Component of the Household Appliances by High Performance Liquid Chromatography Tandem Mass Spectrometry

建立了高效液相色谱-串联质谱( HPLC - MS/MS)结合加速溶剂萃取测定小型家用电器塑料部件中全氟辛酸(PFOA)的分析方法.样品冷冻粉碎后采用甲醇作溶剂进行快速溶剂萃取,萃取液经C18固相萃取柱富集净化后,以C18柱为分离柱,以甲醇-水为流动相,梯度洗脱,电喷雾负离子模式下多反应监测(MRM))模式检测.PFOA在0.5～100.0 μg/L范围内线性关系良好(r2=0.998 9),回收率为93％～ 107％,相对标准偏差为2.9％～7.6％,检出限(S/N =3)为0.5μg/kg.该方法操作简便、灵敏度高,适用于小型家用电器塑料部件中全氟辛酸残留分析.     

超高效液相色谱-串联质谱法测定化妆品还原液内的4-氨基联苯

建立了超高效液相色谱-串联质谱(UPLC-MS/MS)检测化妆品还原液中4-氨基联苯的方法.化妆品试样经过连二亚硫酸钠化学还原后,离心、PCX固相萃取小柱提取富集、净化,并经氨化甲醇洗脱、氮吹至近干,定容后通过UPLC-MS/MS仪检测,分离柱为Waters Acquity BEH C18柱;流动相为0.3％乙腈-甲酸水溶液;流速0.5mL/min.5种不同基质中4-氨基联苯在5～250 ng/mL浓度范围内呈良好的线性关系,线性回归系数r2均大于0.999,检测限均为1 ng/mL.5种不同基质中4-氨基联苯的回收率为80.9％～92.6％,相对标准偏差(RSD)为0.51％～3.76％(n=3).     

气相色谱-质谱联用法测定动物源食品中的杀虫脒及其代谢物残留

建立了动物源性食品(鱼肉、鸡肝、猪肉、虾肉、牛肉)中杀虫脒及其代谢产物4-氯邻甲苯胺残留的气相色谱-质谱联用(GC-MS)检测方法.样品在碱性条件下(pH≥11.0),采用乙酸乙酯均质提取,提取液经石墨化碳黑(GCB SPE,250 mg/3 mL)和中性氧化铝固相萃取柱(Al2O3 SPE,2.0 g/3 mL)净化,GC-MS检测和确证.杀虫脒及其代谢物4-氯邻甲苯胺混合标准溶液的质量浓度在10 ～ 500 μg/L范围内线性关系良好,相关系数(r)分别为0.9991和0.9987,其回收率分别在81％～119％和80％～ 119％之间,相对标准偏差(RSD,n=6)分别为1.1％～11.7％和2.0％ ～ 13.7％,方法的定量下限(LOQ)均为10.0 μg/kg.该方法准确、灵敏、高效、环保,适合于动物源食品中杀虫脒及其主要代谢产物4-氯邻甲苯胺的快速检测.     

基质分散固相萃取-液相色谱-离子阱质谱法检测罐头食品中双酚类化合物残留

建立了采用基质分散固相萃取-液相色谱四级杆串联线性离子阱质谱分析罐头食品中双酚类化合物残留的方法.样品中的双酚类化合物残留经0.1％甲酸乙腈提取,基质分散固相萃取净化,外标法定量,液相色谱-质谱测定.使用数据相关采集扫描功能(IDA)结合增强离子产物(EPI)模式对样品中的双酚类进行定性分析,并建立双酚类的二级子离子谱库.通过MRM模式对双酚类进行定量分析,双酚类化合物在4种罐头食品中的平均回收率为49.3％～128.4％(n=6);相对标准偏差在3.2％～14.4％(n-6)之间,可以满足对罐头食品中的双酚类残留的快速同时定性与定量检测的要求.     

固相萃取-毛细管气相色谱法测定生活饮用水中16种硝基苯类化合物

建立了生活饮用水中16种硝基苯类物质的固相萃取-毛细管气相色谱-电子捕获检测方法.实验优化了色谱柱、升温程序等色谱条件,并对影响固相萃取效果的主要因素(萃取小柱、洗脱剂和洗脱体积)进行了考察.水样中16种硝基苯类物质经Oasis HLB固相萃取柱吸附、正己烷-丙酮(3∶1,V/V)洗脱后,采用DB-1701毛细管气相色谱柱程序升温分离、ECD检测,在33 min内完成所有待测组分的测定.16种硝基苯类组分在各自的线性范围内相关系数r≥0.998,方法的检出限为0.01 ～0.77 μg/L(S/N=3),定量限为0.03 ～2.57 μg/L(S/N=10),日内精度和日间精度分别在1.0％ ～ 3.8％和2.3％～4.8％间,样品加标回收率为83.6％～ 111.8％,加标样品的RSD为1.2％ ～5.1％.应用本方法对50份水样进行了分析,结果表明,本方法准确、灵敏、快速,适用于水质的常规分析,可为水样中硝基苯类物质的污染评价提供技术支持.     

Determination of Sulbactam in Milk by Hydrophilic Interaction Chromatography Tandem Mass Spectrometry ( HILIC - MS/MS)

建立了亲水作用色谱-串联四极杆质谱测定液态奶中微量舒巴坦的分析方法.样品经0.2％乙酸水溶液提取,HLB固相萃取柱净化、富集,以甲酸铵-乙腈为流动相,经Acquity UPLC BEH HILIC色谱柱分离后采用电喷雾质谱多反应监测方式(MRM)扫描,外标法定量.结果表明,舒巴坦的质量浓度在1～100 μg/L范围内线性关系良好,r2大于0.99,定量下限为1.0 μg/kg.加标水平在1.0～50.0 μg/kg范围时,回收率为82％～102％,相对标准偏差(RSD)为1.6％ ～4.7％.该方法前处理简便快捷、灵敏度高、回收率和重现性良好,适用于液态奶中舒巴坦的测定.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.