Vibrational spectra, structure, and proton conduction in hydrous tin dioxide

SnO₂ · nH₂O (hydrous tin dioxide, HTD, n = 1.5) and SnO₂ · nD₂O (deuterated hydrous tin dioxide, DHTD) samples were studied by IR and Raman spectroscopy. The using of these spectroscopic methods elucidated some structural features of the hydrogen-bond network in HTD, where two types of water molecules and two types of hydroxide groups are present. Type 1 water molecules and hydroxide groups are found to be linked to one another by weak hydrogen bonds, as in liquid water. Type 2 water molecules and hydroxide groups are linked to type 1 water molecules and hydroxide groups by rather strong hydrogen bonds. The existence of these strong hydrogen bonds is interpreted as arising from the effect of tin ions on some water molecules and hydroxide groups. Proton conductivity in HTD was found by the impedance method to be a nearly linear function of n. The break of the line at n = 1.3 corresponds to the percolation threshold. The roles of type 1 and type 2 water molecules and hydroxide groups in the generation of proton conduction in HTD are discussed.     

Mesitylenesulfonic acid dihydrate: structure and proton conductivity

The molecular and crystal structure of single-crystalline mesitylenesulfonic acid dihydrate (1) was determined by X-ray diffraction and IR spectroscopy. According to X-ray diffraction data, water molecules in the crystal structure form H₅O₂ ⁺ cations stabilized by an intracationic hydrogen bond with a length of 2.45(1) Å. The formation of the asymmetric H₅O₂ ⁺ cation was confirmed by IR spectroscopy. The crystallographic nonequivalence of the water molecules results in a shift of the bridging proton from the midpoint of the strong hydrogen bond in the cation toward one of the water molecules. The proton conductivity of compound 1 was measured by impedance spectroscopy. Dihydrate 1 is completely dehydrated upon prolonged storage in a dry argon glove box and undergoes the transition to the dielectric state. Compound 1 is stable in the humidity range of 32–66 rel.%. The conductivity of dihydrate 1 is (2.4±0.3) · 10^?5 Ohm^?1 cm^?1 at 298 K, E _a = 0.21±0.01 eV.     

Removal of 63Ni and 57Co from aqueous solution using antimony doped tin dioxide–polyacrylonitrile (Sb doped SnO2–PAN) composite ion-exchangers

Tin dioxide and its antimony doped counterpart were synthesized using traditional sol–gel procedure. The metal oxides were then turned into composites by mixing them with polyacrylonitrile (PAN) and composite spheres ready for use in traditional column applications were obtained. The characterization of materials was investigated by X-ray diffraction, scanning electron microscopy–energy dispersive X-ray, surface area, point of zero charge and thermal analyses. Static batch experiments showed that the antimony doped tin dioxide–PAN (Sb doped SnO₂–PAN) is an effective material for nickel removal and the composite maintains its good metal uptake properties in dynamic column conditions. The composite showed a high nickel uptake capacity of 9 mmol/g in 0.1 M NaNO₃ solution. It was observed that the ion exchange kinetics of antimony doped tin dioxide (Sb doped SnO₂) was remarkably fast for ⁵⁷Co and ⁶³Ni ions but turning the material into PAN composite significantly decreased the materials kinetic properties.     

Retention of Th234 on Some Metal Sulphides

About 99% of active thorium and almost entire inactive thorium is retained on precipitates of tin disulphide and antimony sulphide. The absorption of inactive thorium is slightly faster than active thorium. The retention of active thorium decreases in presence of inactive thorium. Analysis of retention data confirms the heterogeneous distribution of thorium over the precipitate of Sn(IV) and Sb(III) sulphides. Retention takes place by absorption when precipitate is less. In presence of greater amount of precipitate inhomogeneous distribution and diffusion of thorium ions takes place.     

自掺杂型锑氧化物材料的制备、表征及其对Sr(Ⅱ)的吸附性能

⁹⁰Sr 是核电站放射性废液中需要重点去除的核素之一,水合锑氧化物Sb₂O₅·mH₂O可以在酸性条件下选择性吸附脱除⁹⁰Sr. 本文在以醇为溶剂的无水体系中,以化学性能较稳定且毒性低的SbCl₃为原料,以紫外线照射辅助双氧水氧化及控制水解两步法制备出自掺杂型锑氧化物Sb（Ⅲ）/Sb₂O₅. 文中采用X射线光电子能谱（XPS）、X射线衍射（XRD）和傅里叶变换红外（FTIR）光谱对材料结构进行结构表征,并采用批量实验方法研究不同Sb（Ⅲ）/Sb（total）比例与Sr（Ⅱ）吸附性能的相关性,以及溶液pH 值对Sr（Ⅱ）吸附性能的影响. 实验结果表明：Sb（Ⅲ）可在较大的比例范围内共存于立方烧绿石型Sb₂O₅晶格内,形成良好的固溶体Sb（Ⅲ）/Sb₂O₅;制备过程中通过控制醇溶剂的类型、氧化剂的添加方式以及两步反应温度,可以获得具有不同氧化率,即不同Sb（Ⅲ）/Sb（total）比例的Sb（Ⅲ）/Sb₂O₅材料;其中Sb（Ⅲ）/Sb（total）比例为49.8%的锑氧化物材料吸附性能最好,在纯水体系下对Sr（Ⅱ）的分配系数为6.6×107 mL·g^-1,在pH=3-13 范围内对Sr（Ⅱ）具有良好的吸附性能,并且在本文实验条件下,Sr（Ⅱ）在锑氧化物材料上的吸附更好地符合Langmuir吸附模型.     

环氧化物法制备锑掺杂氧化锡气凝胶

以无机金属盐为前驱体,采用环氧丙烷添加法结合CO2超临界流体干燥和热处理工艺,制备了不同锑掺杂浓度的二氧化锡(ATO)气凝胶.所得气凝胶为深蓝色块体,平均密度约为600 mg?cm-3,锑掺杂浓度在5%到20%(x)之间.电子显微镜图片显示ATO气凝胶的骨架由粒径约为数十纳米的颗粒堆积而成,而这些颗粒又由数纳米的初级球形颗粒构成.X射线衍射谱表明,样品的主要晶相为SnO2四方相金红石结构,锑的掺杂仅引起微小的晶格畸变.X射线光电子谱显示锡元素以+4价态存在,而锑则具有+3和+5的混合价态.四探针电阻率测试仪的结果表明,ATO气凝胶的电阻率在2.7-40Ω?cm之间变化,其中在锑掺杂浓度(x)为12%时具有最低电阻率.     

Structure and Mobility Pattern of Proton-Containing Groups in Hydrates of Titanium,Zirconium and Tin Acid Phosphates; Their Conducting and Ion Exchanging Properties

Abstract

Phosphates of tetravalent elements are practically important for ion exchange, catalysis and conductivity. This study deals with a number of hydrates of titanium, tin and zirconium phosphates. PMR data show that the structure of water molecules in hydrates is slightly distorted, and at temperatures higher than 160 K water has high translation mobility. NMR ³¹P proves HPO² ₄ dissociation to be growing with increase of temperature. Energetic parameters of this process are determined. Close values of anion dissociation enthalpy (0, 16/2/Ev) and obtained activation energy of conductivity for di- and monohydrates (0,17/2/Ev) show tunnel pattern of proton transfer along H-bond direction, This type of correlation was not observed in anhydrous compounds. That can be explained by impossibility of anion proton tunneling because of H-bond weakening. Proton conductivity of acid phosphates was studied. Ten-fold decrease of conductivity at room temperature with the loss of each water molecule proves H₂O participation in proton transport. Mechanism of this process is discussed with the use of NMR data. Dependence of water mobility and conductivity level on the degree of crystallinity is also discussed. With the help of NMR-data processes of ion exchange in tin and zirconium acid phosphates, as well as the state of developed salt forms were studied. Presence of lithium with high mobility in Li₂Sn(PO₄)₂ ·nF₂O was established.     

Simultaneous determination of arsenic, antimony, selenium and tin by gas phase molecular absorption spectrometry after two step hydride generation and preconcentration in a cold trap system

A cold trap system for the simultaneous determination of arsenic, antimony, selenium and tin by continuous hydride generation and gas phase molecular absorption spectrometry is described. The hydride generation is carried out in two steps; first, tin hydride is generated at low acidity and second, arsenic, antimony and selenium hydrides are formed at higher acidity. All the hydrides are collected in a liquid nitrogen cryogenic trap and transported to the flow cell of a diode array spectrophotometer, where molecular absorption spectra are obtained in the 190-250 nm range. Five calibration solutions containing arsenic, antimony, selenium and tin are solved using multiple linear regression analysis. Tests are performed in order to extend the same manifold to other hydrides but no signals are obtained for bismuth, cadmium, lead, tellurium and germanium. Under the optimum conditions found and using the wavelengths of maximum sensitivity (190, 198, 220 and 194 nm), the analytical characteristics of each element are calculated. The detection limits are 0.050, 0.020, 0.12 and 1.1 mug ml(-1) and the RSD values are 3.7, 3.1, 3.5 and 3.0% for As, Sb, Se and Sn, respectively. The method is applied to As, Sb, Se and Sn determination in natural spiked water samples.     

121Sb-Mössbauer-Spektren von Antimon(V)-Verbindungen. II

¹²¹Sb Mössbauer Spectra of Antimony (V) Compounds. II The Mössbauer resonance effect of ¹²¹Sb has been studied at 4.2 K in a series of 11 antimony(V) compounds which are in most cases bridged. Isomer shift and quadrupole splitting variations are considered in the light of results of X-ray and vibrational spectroscopy. Preparation and the vibrational spectra of [NMe₄][SbCl₄(n₃)₂] are described. Within the limitations of available structural data related tin compounds are compared with those of corresponding ¹¹⁹Sn Mössbauer spectra.     

Facile preparation of Sb and oxide-coated Sb nanoparticles via cathodic dispersion of bulk Sb in different media

We report here a facile electrochemical method on the preparation of antimony nanoparticles (NPs) by dispersing a bulk antimony electrode under highly cathodic polarization in different media at room temperature, requiring neither precursor ions nor organic capping agents. The dispersion of bulk antimony in a tetrabutyl ammonium bromide (TBAB) acetonitrile solution involved the formation and oxidation of an unstable Zintl compound of antimony, and the as-prepared Sb NPs were readily transferred into Sb–Sb₂O₃ core–shell NPs during the post treatment and characterization because of the surface oxidation of Sb NPs by oxygen in the air. In contrast, Sb NPs prepared by dispersing the bulk antimony cathode in a blank aqueous NaOH solution were oxygen-resistant in the air because the strongly adsorbed hydroxide ions from the solution could stabilize the Sb NPs. The incorporation of sodium, the formation/oxidation of polyanions of antimony (Zintl ions), and the formation/decomposition of unstable antimony hydrides may all take effect for the cathodic dispersion of bulk antimony electrodes in the NaOH solution. Transmission electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy and Raman spectroscopy were used to characterize these NPs.     

Nafion-based composite solid electrolytes containing water-soluble fullerene C<Subscript>60</Subscript> derivatives

Nafion-based composite solid polyelectrolytes containing fullerene C₆₀ and its water-soluble derivatives fullerenol-C₆₀ and tris-malonate-C60 were studied by the impedance spectroscopy method. It was found that introduction of these dopants in Nafion leads to a substantial increase in proton conductivity of the composites in the region of low relative humidity. The reasons for the influence of dopants on proton conductivity of composites were discussed.     

Flow analysis-hydride generation-Fourier transform infrared spectrometry. A new analytical technique for the simultaneous determination of antimony,arsenic and tin

The combination of flow analysis (FA), hydride generation (HG) and Fourier transform infrared (FTIR) spectrometry is proposed as a novel and powerful analytical technique for the individual and simultaneous determination of antimony, arsenic and tin in aqueous samples. The analytes were transformed into the volatile hydride form by on-line reaction with sodium tetrahydroborate in acidic medium. The gaseous analyte hydrides [M(n)H(m), (g)] generated, were transported by means of a carrier gas stream inside the IR gas cell and the corresponding FTIR spectrum was acquired in a continuous mode. The 1893, 1904 and 2115 cm(-1) bands of the SbH3, SnH4, and AsH3 were selected for the determination of antimony, tin and arsenic, respectively. The limit of detection (3sigma) obtained by using a short-path (10 cm) IR gas cell were 0.25, 0.30 and 1.2 mg l(-1) for the determination of antimony, tin and arsenic, respectively; while the precision (relative standard deviation, RSD, n 5) found from a standard solution containing 50 mg l(-1) of each element was, in all cases, less than 0.3%. However, the use of a long-path (7.25 m) IR gas cell improved the figures of merit (sensitivity, limits of detection and quantification) nearly 60-fold. The effect of the main experimental and instrumental variables, such as acidic media, sodium tetraborohydrate concentration, nitrogen flow rate, nominal resolution and the scan accumulation on the analytical signals of the antimony, tin and arsenic hydrides, were studied. Further, the potential of the proposed technique for the simultaneous determination of these elements was tested, analyzing synthetic samples containing different amounts of Sb, Sn and As.     

[Sb(12-Krone-4)2(CH3CN)][SbCl6]3 und [Bi(12-Krone-4)2(CH3CN)][SbCl6]3, die ersten Trikationen von Antimon(III) und Bismut(III)

[Sb(12-Crown-4)₂(CH₃CN)][SbCl₆]₃ and [Bi(12-Crown-4)₂(CH₃CN)][SbCl₆]₃, first Trications of Antimony(III) and Bismuth(III) The crown ether complexes [M(12-crown-4)₂(CH₃CN)][SbCl₆]₃ with M = Sb and Bi are formed by the reaction of antimony trichloride and bismuth trichloride, respectively, with antimony pentachloride in acetonitrile solution in the presence of 12-crown-4. They form colourless, moisture sensitive crystals, which were characterized by X-ray structure determinations and by IR spectroscopy. The complex with M = Sb was also characterized by ¹²¹Sb Mössbauer spectroscopy. Both complexes crystallize isotypically in the orthorhombic space group Pbcn with four formula units per unit cell. M = Sb: 3 483 observed unique reflections, R = 0.038. M = Bi: 2 958 observed unique reflections, R = 0.036. The compounds consist of SbCl₆^? ions and trications [M(12-crown-4)₂(CH₃CN)]³⁺, in which the M³⁺ ions are ninefold coordinated by the eight oxygen atoms of the crown ether molecules and by the nitrogen atom of the acetonitrile molecule. The lone pair of the M³⁺ ions has no steric effect.     

Antimony speciation by inductively coupled plasma mass spectrometry using solid phase extraction cartridges

A novel and simple method for inorganic antimony speciation is described based on selective solid phase extraction (SPE) separation of antimony(III) and highly sensitive inductively coupled plasma mass spectrometric (ICP-MS) detection of total antimony and antimony(V) in the aqueous phase of the sample. Non-polar SPE cartridges, such as the Isolute silica-based octyl (C8) sorbent-containing cartridge, selectively retained the Sb(III) complex with ammonium pyrrolidine dithiocarbamate (APDC), while the uncomplexed Sb(V) remained as a free species in the solution and passed through the cartridge. The Sb(III) concentration was calculated as the difference between total antimony and Sb(V) concentrations. The detection limit was 1 ng L(-1) antimony. Factors affecting the separation and detection of antimony species were investigated. Acidification of samples led to partial or complete retention of Sb(V) on C8 cartridge. Foreign ions tending to complex with Sb(III) or APDC did not interfere with the retention behavior of the Sb(III)-APDC complex. This method has been successfully applied to antimony speciation of various types of water samples.     

Synthesis,characterization, and antimicrobial activity of heterobimetallic complexes of Sn(IV) and Zn(II) with 4-aminophenylacetic acid

A series of new heterobimetallic complexes of zinc and tin with 4-aminophenylacetic acid has been prepared. Their composition and structure in solid state and in solution have been elucidated by elemental analysis, IR, ¹H NMR, and ¹³C NMR spectroscopy. IR spectroscopy results have confirmed the bidentate nature of the ligand, its molecules being arranged in planar square [Zn(II)] and trigonal bipyramid [Sn(IV)] around the metal ions. NMR studies have revealed four-coordinated geometry in the solution. The complexes containing both Sn(IV) and Zn(II) are better antimicrobial agents as compared to the Zn-only analog.     

Characterization of the chemical composition of archaeological glass finds from South-Eastern Bulgaria using PIXE, PIGE and ICP-AES

Using PIXE (proton induced X-ray emission), PIGE (proton induced gamma emission) and ICP-AES (inductively coupled plasma-atomic emission spectroscopy) the concentrations of the 24 elements Al, As, Ba, Br, Ca, Cl, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Pb, Rb, S, Sb, Si, Sn, Sr, Ti, Zn and Zr in 53 archaeological glass samples from South-Eastern Bulgaria, were determined. The glasses are dated from the 1st to 6th century AD. The analytical data showed the samples to be typical soda-lime-silica glass, with natron as flux. A rather broad range of aluminium, titanium and iron impurities was found, with a tendency for more impure glass in the later periods. The decolouring agents were antimony and manganese oxides, with Sb prevailing in earlier, and Mn in later glass.     

Zeolitic inorganic–organic polymer electrolytes: a material based on poly(ethylene glycol) 600, SnCl4 and K4Fe(CN)6

This report describes the synthesis of a new zeolitic inorganic–organic polymer electrolyte with the formula [Fe_xSn_y(CN)_zCl_v(C_2nH_4n+2O_n+1)K₁]. This material is based on poly(ethylene glycol) 600, SnCl₄ and K₄[Fe(CN)₆], and is obtained via a sol→gel transition. Mid and far Fourie than form infrared (FT‐IR) studies, analytical data and X‐ray Photoelectron spectroscopy (XPS) investigations allowed us to conclude that this material is a mixed inorganic–organic network in which Fe and Sn are bonded by CN bridges and tin atoms by PEG 600 bridges. Mid‐infrared (MIR) FT‐IR investigations demonstrated that the polyether chains assume a conformation of the TGT (T = trans, G = gauche) type. Micrographs of the compound obtained by scanning electron microscopy reveal that its morphology resembles a smooth gummy paste. The conductivity of the material at different temperatures was determined by impedance spectroscopy (IS). Results indicated that the material conducts ionically and that its conductivity is strongly influenced by segmental motion of the polymer network. Finally, this network shows a conductivity of ca. 3.7 × 10⁻⁵ S/cm at 25 °C. Copyright © 2000 John Wiley & Sons, Ltd.     

Separation of tin from some metals by extraction chromatography

Much attention has been devoted to Sn (IV) strongly retained on the TBP-Daiflon column from 2M HCl in extraction chromatography. The separations of Sn?Cu, Zn, As, Cd, Sb, Pb,¹¹³Sn-¹²⁵Sb,¹¹³Sn-^113mIn (^113mIn milking) and Sn?Hg?Fe were successfully achieved without any contamination. In the separations, except for the last, only tin was retained separately on the column upon passing the mixed solution. The daughter indium was eluted with 0.5M HCl. In the last separation, iron was eluted with 0.5 M HCl, tin with 0.1M HCl and mercury with 2M HNO₃, for these metals retained on the column. Radioactive tracers for tin, iron, mercury and antimony were used.     

Tin trifluoroacetylacetonate [Sn(C<Subscript>5</Subscript>H<Subscript>4</Subscript>O<Subscript>2</Subscript>F<Subscript>3</Subscript>)<Subscript>2</Subscript>] as a precursor of tin dioxide in APCVD process

A new method of synthesis of volatile complex, tin trifluoroacetylacetonate [Sn(C₅H₄O₂F₃)₂], was proposed. The prepared compound was identified by IR spectroscopy, CH analysis, X-ray powder diffraction, and DTA/TGA, the composition was confirmed by MALDI-TOF mass spectrometry, crystal structure was established. Thin films of tin dioxide on silicon were obtained by atmospheric pressure chemical vapor deposition using [Sn(C₅H₄O₂F₃)₂] as a precursor. The morphology and composition of the films were studied by scanning electron microscopy, EDX elemental analysis, and X-ray powder diffraction. Surface resistance and light transmission in visible and near IR region were studied.     

2,2′-联咪唑磷钨酸盐和氧化石墨复合物的制备及其质子导电性能(英文)

制备了氧化石墨同基于2,2′-联咪唑(简记为H2biim)和磷钨酸的有机-无机络合物(其分子式简记为{H6[(H2O)1.5(H2biim)2(CH3OH)]2[(H2biim)(CH3OH)2][PW12O40]2·2CH3CN}n(1))的两个复合物(分别简记为1-GO1和1-GO2).利用红外光谱仪和X射线衍射仪表征了合成产物的结构.此外,在25~100℃温度范围内和35%~98%相对湿度范围内,利用电化学阻抗谱测定了2种产物的质子导电性.结果表明,化合物1的结构特征在两个复合物中得以保留.在约98%相对湿度下,1-GO1和1-GO2在温度25~100℃范围内的质子导电率达1.26×10-3~2.2×10-3S·cm-1;在温度100℃、相对湿度35%~98%范围内,1-GO1和1-GO2的质子导电率达0.64×10-3~2.2×10-3S·cm-1.此外,在同等条件下,1-GO1和1-GO2的质子导电性优于化合物1.