液态Wood合金在氢氧化钠电解质溶液中的电毛细变形现象

本文研究了液态Wood合金在氢氧化钠电解质溶液中,通过施加外电场,进而诱发液态金属电毛细变形的现象.当石墨电极伸入金属液滴内部时,通电后在金属表面发生的电极反应,促使金属表面形成氧化膜或去除氧化膜.由于氧化膜与液态金属的表面张力存在巨大差异,通电后电极极性的变化可实现金属液滴形状的快速可逆变形.在液态金属与电解质溶液之间形成的双电子层中,当两侧聚集同极性电荷时将降低界面张力.为维持通电后体系自由能最小,将迫使液体金属增大与溶液之间的界面面积,在宏观上表现为液体金属的变形,由于液态金属与氢氧化钠反应后自身携带负电荷,在电场力的作用下可有效地驱动液态金属在电解质溶液中的运动.     

计算机控制电毛细曲线测量

电毛细曲线在双电层结构的研究中应用十分广泛。表面张力随电位的变化能给出电极表面电荷量及其符号的信息。在电毛细曲线的最高点，表面张力相对于电位的变化为零，因而为电极的零电荷电位。电极一溶液界面的许多性质与电位偏离零电荷电位的程度有关。电毛细曲线在电极表面吸附现象的研究中也是重要的手段。     

毛细电色谱法分离七种苯取代物

用毛细电色谱法成功地分离了七种苯取代物,并获得了很好的重现性和分离度。     

在不同体积比流动相及不同缓冲溶液中毛细电色谱ODS柱的分离行为

１引言毛细电色谱中，流动相的选择同样取决于固定相及被分离样品。对于ＯＤＳ柱，若分离中性样品时，通常选择一定体积比的有机相和无机缓冲溶液混合，如一定百分比的ＣＨ３ＣＮ和一定百分比的Ｎａ２Ｂ４Ｏ７水溶液。流动相浓度配比不同时，样品在固定相上的保留不同，进而造成分离时间和选择性不同。笔者通过实验观察到，当在同样浓度的有机相中加入的缓冲溶液不同时，固定相对样品的分离能力也不尽相同。本文即以实验为依据，分别讨论ＯＤＳ柱在不同体积比流动相及在相同体积比流动相，不同缓冲溶液下的分离行为。２实验部分２．１仪器与…     

稀土在电沉积镍-钴合金中的作用

由于稀土元素具有独特的电子层结构和化学性能,使稀土及其化合物在材料科学领域中的应用越来越广泛,尤其是稀土在电沉积过程中的研究及应用正日趋深入。这是因为在电镀溶液中加入少量的稀土化合物后,可以改善镀液的分散能力和深镀能力,提高电镀的电流效率,增加镀层的硬度和耐蚀性等[1 4],但有关稀土在电沉积镍 钴合金中的作用的研究还未见报道。本文研究了在硫酸盐体系镍 钴合金电镀液中加入少量的稀土化合物后对电沉积过程、合金电极的催化性能、合金镀层的形貌和成分的影响。1　实验方法基础镀液成分(g/L)为NiSO4·7H2O200,CoSO4…     

化学镀镍磷合金在浓NaOH溶液中的电化学腐蚀行为

微观结构;腐蚀电化学;化学镀镍磷合金在浓NaOH溶液中的电化学腐蚀行为     

聚吡咯微粒掺入的聚苯乙烯膜在电解质溶液中的介电弛豫谱及其解析

在40 Hz～11 MHz频率范围测量了聚苯乙烯膜以及混入聚吡咯粒子的聚苯乙烯膜和电解质溶液构成的体系的介电谱, 发现了特异的弛豫现象: 纯的和掺入导电性聚吡咯后的聚苯乙烯膜分别显示出单一弛豫和双弛豫的不同模式的介电谱. 在Maxwell-Wagner界面极化概念基础上解释了该弛豫机制: 高、低频弛豫分别由膜-液界面极化和膜相本身的不均一性引起的. 将体系进行了模型化, 并利用Hanai理论方法对谱进行了解析, 获得了内部电性质的诸多参数. 对不同聚吡咯掺入量的膜/溶液体系的介电测量和解析结果表明, 电解质溶液的种类、浓度以及膜中混入聚吡咯的量都影响着膜相的介电响应. 这些结论为利用加入导电粒子改善绝缘高分子聚合物的电性质的研究以及制备既具有导电功能又使基体的力学性能得到提高的高分子复合物提供了重要的线索.     

电解质溶液对聚吡咯电聚合中过氧化行为的影响

分别以硫酸/水和高氯酸锂/乙腈为电解质溶液, 采用循环伏安法在铂基底电极上电聚合制备了聚吡咯, 研究了电解质溶液对聚吡咯电聚合过程中过氧化行为的影响. 与硫酸/水溶液相比, 在高氯酸锂/乙腈溶液中电聚合制备的聚吡咯发生过氧化的峰电位正移了0.42 V. 采用原位傅里叶变换红外(in situ FTIR)光谱技术检测, 结果表明, 电聚合制备的聚吡咯在2种电解质溶液中均发生了过氧化反应, 其β-C经氧化生成C-OH或CO. 在硫酸/水溶液中, 部分聚吡咯发生电氧化降解生成CO₂, 致使其共轭结构被破坏, 电导率迅速下降. 而在高氯酸锂/乙腈溶液中, 在更高的电位范围内, 聚吡咯并没有氧化降解成CO₂.     

铁阳极在浓NaOH溶液中的极化特征

使用极化曲线、电解曲线对纯铁电极在浓NaOH 溶液中的极化过程进行了研究. 结果表明, 碱溶液温度越高, 碱浓度越低,电流密度越高, 铁阳极越容易发生钝化;但在某些情况下, 铁电极出现钝化的现象很微弱甚至观察不到.电解法制备高铁酸盐的适宜条件为, 温度25-35 ℃, 极化电流密度≤4.7 mA·cm-2, 碱浓度≥ 14.5 mol·L-1. 用电化学阻抗谱(EIS)研究了上述极化过程中电极表面的阻抗变化情况, 据此描述了铁阳极在浓NaOH溶液中超钝化区极化时的阶段特征.     

Er-Bi合金膜在有机溶剂中的电沉积研究

利用循环伏安法和恒电位电解法探讨了室温条件下在二甲基亚砜(DMSO)中Er-Bi合金膜的电化学制备.研究了沉积电位、电流密度以及主盐浓度比对沉积膜质量的影响.实验结果表明,在ErCl3-Bi(NO3)3-LiCl-DMSO体系中,当控制恰当的体系组成和沉积条件,均可得到表面均匀、附着力强、有金属光泽的灰黑色非晶态Er-Bi合金膜,其中稀土Er的质量分数可达24.09％～46.56％.通过SEM、EDS分析得到沉积膜表面形貌和组成,通过XRD和DSC确定了合金膜的物相组成.结果表明,当所制备的合金膜在723 K进行热处理1 h后,可形成稳定的Er-Bi合金相.     

铝在氢氧化钠溶液中的电化学行为研究

铝是地壳中含量丰富的元素 ,分布广泛 ,由于其具有价格低、能量密度高、导电性良好及无毒性等优点 ,因而是阳极材料的首选物质 ,铝电池的研究也已经成为近年来研究开发的热点课题之一[1～ 3] 。探讨铝在强碱性溶液中的溶解机理 ,对铝电池的研究和开发将具有一定的理论指导意义。1　实验部分1 1　仪器与试剂ＢＡＳ 1 0 0Ａ电化学系统 (美国ＢＡＳ仪器公司 ) ;ＣＳ5 0 1型恒温槽 ;工作电极为直径是 0 .3ｍｍ的铂圆盘电极 ,参比电极是标准甘汞电极 (ＳＣＥ)。铝( 99.99% ) (天津化学试剂厂 ) ,氢氧化钠为分析纯(上海化学试剂厂 ) ,水为二次蒸…     

Structure and dynamics at the surface of a concentrated aqueous solution of CsF

A molecular dynamics simulation of a liquid layer of a concentrated CsF solution in water has been performed in order to compare the results with those obtained in an experimental study of our group. The main result of the experiment was the existence of a monolayer of nearly pure water constituting the surface and a homogeneous mixture constituting the bulk of the system. The simulation reveals the same phenomena which can be explained by the circumstance that the ions near the surface mostly keep their first solvation shell intact. The water molecules belonging to these shells and being placed on the vapor side constitute this monolayer. The density profiles of the ions indicate that the Cs ions penetrate further into the surface than the F ions. The orientational structure of the first shell of water molecules around an ion is the same for ions in the surface and ions in the bulk in contrast to the dynamics which is altered. The spectra of the librational motion are shifted to lower frequencies. In addition to that the spectra belonging to libration which involves motion of the dipole moment develop a peak in the low frequency range irrespective of whether the water molecules are bonded to Cs or to F ions. This can be correlated with an overall preferred orientation of the water molecules in the surface which is most pronounced for the dipole moment. The calculation of the diffusion coefficients shows that the top surface layer of nearly pure water is a region of enhanced and extremely anisotropic mobility. The mean residence time of water molecules in the surface in the first shell of an ion is reduced according to the enhanced mobility.     

Studies on microstructure and aqueous solution properties of block copolymer of acrylamide-styrene

Three series of block copolymers of acrylamide (AM) and styrene (St) as hydrophobic comonomer with varied microstructures were prepared in microemulsion medium by changing feed ratio of monomers, ratio of St to surfactant, and amount of initiator, respectively. The effects of microstructure factors of the amphiphilic block copolymers PAM-b-PSt on their aqueous solution properties were investigated by fluorescence probe technique and surface tension measurement in detail. The experimental results show that the aqueous solution properties of PAM-b-PSt are strongly dependent on their microstructure factors, such as the length and content of PSt hydrophobic blocks in the copolymers and their molecular weight. It was found that the main microstructure factors which effect the hydrophobic association behavior of the copolymer PAM-b-PSt are the length and content of PSt hydrophobic blocks in the copolymer, whereas the hydrophobic association behavior of the copolymer is not affected nearly so much by molecular weight in more dilute regions. At the same time, it was also found that the main microstructure factors which affect the surface activity of the copolymer are the content of PSt hydrophobic blocks in the copolymer and molecular weight, whereas the length of PSt blocks in copolymer does not affect surface activity of the copolymer nearly so much under fixed content of PSt hydrophobic blocks and molecular weight in the copolymer.     

Dissolving of cellulose in PEG/NaOH aqueous solution

Here, a new solvent system for cellulose is reported. The solvent is a mixed aqueous solution of 1.0 wt.% poly(ethylene glycol) (PEG) and 9.0 wt.% of NaOH. Cellulose powder was added into the mixture at room temperature at first, and freezing it at −15 °C for 12 h following a thaw of the mixture at room temperature under strong stirring. There formed a clean solution of cellulose, and the optical microscopy was used to record the dissolving process. ¹³C-NMR, FT-IR, XRD, and intrinsic viscosity measurements revealed that there forms a homogeneous solution of cellulose in the new solvent system. The maximum solubility of cellulose with average molecular weight of 1.32 × 10⁵ g mol⁻¹ in the solvent system is 13 wt.%. The cellulose solution in the new solvent system is stable, even for 30 days storage at room temperature.     

Dissolution and regeneration of cellulose in NaOH/thiourea aqueous solution

A novel cellulose solvent, 1.5 M NaOH/0.65 M thiourea aqueous solution, was used to dissolve cotton linters having a molecular weight of 10.1 × 10⁴ to prepare cellulose solution. Regenerated cellulose (RC) films were obtained from the cellulose solution by coagulating with sulfuric acid (H₂SO₄) aqueous solution with a concentration from 2 to 30 wt %. Solubility of cellulose, structure, and mechanical properties of the RC films were examined by infrared spectroscopy, X‐ray diffraction, scanning electron microscopy, ¹³C NMR, and tensile tests. ¹³C NMR analysis indicated that the novel solvent of cellulose is a nonderivative aqueous solution system. The presence of thiourea enhanced significantly the solubility of cellulose in NaOH aqueous solution and reduced the formation of cellulose gel; as a result, thiourea prevented the association between cellulose molecules, leading to the solvation of cellulose. The RC film obtained by coagulating with 5 wt % H₂SO₄ aqueous solution for 5 min exhibited higher mechanical properties than that with other H₂SO₄ concentrations and a homogenous porous structure with a mean pore size of 186 nm for free surface in the wet state. The RC film plasticized with 10% glycerin for 5 min had a tensile strength of 107 MPa and breaking elongation of 10%, and about 1% glycerin in the RC film plays an important role in the enhancement of the mechanical properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1521–1529, 2002     

Homogenous synthesis of hydroxyethylcellulose in NaOH/urea aqueous solution

Hydroxyethylcellulose (HEC) was synthesized by a fully homogenous method from cellulose in 7.5 wt.-% NaOH/11 wt.-% urea aqueous solutions under mild conditions. HEC samples were characterized with NMR, SEC-LLS, solubility, and viscosity measurements. The MS and DS values of the obtained HEC samples are in the range from 0.54 to 1.44 and 0.45 to 1.14, respectively, and the relative DS values at C-2 and C-6 hydroxyl groups are slightly higher than those at C-3 hydroxyl groups. HEC samples are soluble in water starting from a MS of 0.57 and DS of 0.49, which display high viscosity in aqueous solutions. Moreover, a NaOH/urea aqueous solution is a stable system for cellulose etherification. In this way, we could provide a simple, pollution-free, and homogeneous aqueous solution system for synthesizing cellulose ethers.     

Effect of procaine hydrochloride on the micellization of double tailed surfactants in the aqueous solution

The effects of procaine hydrochloride (PC) on the micellization of two kinds of double tailed surfactants in aqueous solutions, sodium bis (2-ethyl-1-hexyl) sulfosuccinate (AOT) and didodecyldimethylammonium bromide (DDAB), were studied by surface tension measurements. The results revealed that PC could decrease the equilibrium surface tension and critical micelle concentration (cmc) of AOT, but it is opposite for DDAB. Their standard thermodynamic parameters of micellization, , and , have been calculated in aqueous solutions. The locations of PC in the two kinds of micelles were investigated by UV and fluorescence spectroscopy. It is found that the mixed micelle of AOT and PC could be formed, but the effect of PC on the micellization of DDAB is quite small.     

Solubilization and conformational behavior of Zein in aqueous solution of dodecyldimethylethylammonium bromide (DDAB)

The solubilization and conformational behavior of Zein in the presence of cationic surfactant, dodecyldimethylethylammonium bromide (DDAB) have been studied. The colloidal properties of DDAB in the absence and presence of Zein have also been investigated using physico-chemical and spectroscopy methods. The surfactant appears to bind to Zein at concentrations below the critical micelle concentration (cmc) and the binding becomes weaker at concentrations above the cmc. The interaction between DDAB and Zein depends on the chemical structure and molecular parameters (conformation, molar mass, charge) of the protein. The schematic sketches of the molecular mechanisms of the complex formation between like-charged proteins and surfactants have been proposed.     

Ionic liquid induced changes in the properties of aqueous zwitterionic surfactant solution

Modifying properties of aqueous surfactant solutions by addition of external additives is an important area of research. Unusual properties of ionic liquids (ILs) make them ideal candidates for this purpose. Changes in important physicochemical properties of aqueous zwitterionic N-dodecyl- N, N-dimethyl-3-ammonio-1-propanesulfonate (SB-12) surfactant solution upon addition of hydrophilic IL 1-butyl-3-methylimidazolium tetrafluoroborate, [bmim][BF 4], are reported. Dynamic light scattering results indicate a dramatic reduction in the average micellar size in the presence of [bmim][BF 4]; micellar (or micelle-like) aggregation in the presence of as high as 30 wt % [bmim][BF 4] is confirmed. Responses from fluorescence probes are used to obtain critical micelle concentration (cmc), aggregation number ( N agg), and dipolarity and microfluidity of the micellar pseudophase of aqueous SB-12 in the presence of [bmim][BF 4]. In general, increasing the amount of [bmim][BF 4] to 30 wt % results in decrease in N agg and increase in cmc. Increase in the dipolarity and the microfluidity of the probe cybotactic region within the micellar pseudophase is observed on increasing [bmim][BF 4] concentration in the solution. It is attributed to increased water penetration into the micellar pseudophase as [bmim][BF 4] is added to aqueous SB-12. It is proposed that IL [bmim][BF 4] behaves similar to an electrolyte and/or a cosurfactant when present at low concentrations and as a polar cosolvent when present at high concentrations. Electrostatic attraction between cation of IL and anion of zwitterion, and anion of IL and cation of zwitterion at low concentrations of [bmim][BF 4] is evoked to explain the observed changes. Presence of IL as cosolvent appears to reduce the efficiency of micellization process by reducing the hydrophobic effect.