首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 203 毫秒
1.
在Si衬底GaN基蓝光LED芯片上生长了一层SiON钝化膜,使器件的光输出功率提高12%且有效降低了器件在老化过程中的光衰。对有、无钝化膜的样品进行性能比较,结果表明SiON钝化膜能有效隔离环氧树脂与高温芯片,缓解环氧树脂的老化变黄;又能部分弛豫环氧树脂对芯片的张应力,降低非辐射复合中心产生的几率;有效减小器件的侧壁漏电通道,降低器件的光衰和漏电流,提高器件的可靠性。  相似文献   

2.
ZnO外延膜与蓝宝石衬底的取向偏差及其弯曲变形   总被引:1,自引:1,他引:0  
采用常压MOCVD方法在Al2O3(00.1)衬底上生长出了高质量ZnO单晶薄膜。由ZnO(00.2)面和Al2O3(00.6)面及ZnO(10.2)面和Al2O3(11.6)面X射线双晶(w/2θ衍射曲线的相对峰位,得到ZnO外延膜的晶格常数及外延层和衬底间的取向差异角。结果表明外延层和衬底在应力作用下产生了取向差和晶格畸变,并且取向倾斜方向与衬底的切割倾角方向一致;高温直接生长的样品的取向差比有低温缓冲层样品更大,晶格畸变也更严重。高温直接生长的样品弯曲半径小而应力更大;实验测量的应力值和理论计算的热应力值之间存在差异,原因主要是晶格失配应力的存在。有缓冲层的样品由于能更好地弛豫晶格失配引入的应力,热应力所占整个残余应力的比例相对更大。  相似文献   

3.
SiN钝化膜对Si衬底GaN基蓝光LED性能影响   总被引:4,自引:2,他引:2       下载免费PDF全文
利用等离子辅助化学气相沉积(PECVD)系统在垂直结构Si衬底GaN基蓝光LED芯片上生长了SiN钝化膜,并对长有钝化膜及未作钝化处理的LED在不同条件下进行了老化实验,首次研究了SiN钝化膜对垂直结构Si衬底GaN基蓝光LED可靠性的影响。实验发现:经过30mA、85℃、24h条件老化后,未作钝化处理的Si衬底GaN基蓝光LED的平均光衰为11.41%,而长有SiN钝化膜的LED平均光衰为6.06%,SiN钝化膜有效地改善了LED在各种老化条件下的光衰,另外,SiN钝化膜缓解了Si衬底GaN基蓝光LED老化过程中反向电压(Vr)的下降,但对老化后LED的抗静电击穿能力(ESD)没有明显的影响。  相似文献   

4.
江洋  罗毅  席光义  汪莱  李洪涛  赵维  韩彦军 《物理学报》2009,58(10):7282-7287
研究了具有不同台阶数目的AlGaN插入层对在6H-SiC衬底上利用金属有机物气相外延(MOVPE)生长的GaN体材料残余应力和表面形貌的影响.高分辨率X射线衍射测试表明样品的c轴晶格常数随台阶数目的增多而增大;低温光荧光谱中GaN发光峰也随着台阶数目增多而发生蓝移,这些变化都反映出GaN中残余张应力的减小.此外,原子力显微镜测试表明样品表面起伏和粗糙度也都随着插入层的引入和台阶数目的增多得到了明显的改善. 关键词: 残余应力 表面形貌 SiC衬底 AlGaN插入层  相似文献   

5.
人们已提出用BAlGaN四元系材料制备紫外光谱区的光发射器件.GaN和AlN二元系是这种四元材料在器件应用中的基础材料.6H-SiC衬底在氮化物生长中因其晶格失配小是一大优势,而且SiC衬底的热膨胀系数也和AlN的很接近.然而,对于AlN外延层来说,需要控制其中的残余应力,因为在SiC衬底上直接生长的AlN外延层中存在着因晶格失配所产生的压缩应力.另一方面,在SiC衬底上直接生长的GaN外延层中存在着拉伸应力.这种拉伸应力起源于GaN比衬底有着更大的热膨胀系数.本文讨论了在6H-SiC衬底上生长的氮化物外延层中残余应力的类型、数量及控制.为此目的,提出了在6H-SiC衬底上,无论是生长AlN,还是生长GaN,都可以采用(GaN/AlN)多层缓冲层的办法,作为控制残余应力的有效方法.我们还讨论了AlN和GaN外延层的结晶质量和残余应力间的关系.  相似文献   

6.
在蓝宝石衬底上生长了以AlN/GaN超晶格准AlGaN合金作为势垒的HEMT结构材料,并与传统AlGaN合金势垒样品进行了对比.在高Al组分(≥40%)情况下,超晶格势垒样品的表面形貌明显改进,电学性能特别是2DEG面电子浓度也有所改进.对超晶格势垒生长参数进行了初步优化,使得HEMT结构薄层电阻进一步降低,最后获得了251 Ω/□的薄层电阻. 关键词: AlGaN/GaN 结构 AlN/GaN超晶格 二维电子气 高电子迁移率晶体管  相似文献   

7.
采用两步AlN缓冲层(一层低温AlN和一层高温AlN)在r面蓝宝石衬底上生长了非极性的α面GaN,并利用高分辨X射线衍射和光致荧光谱对所生长的材料进行了研究.两步AIN缓冲层在我们之前的工作中已被证明比单步高温AlN或低温GaN缓冲层更有利于减小材料各向异性和提高晶体质量,本文进一步优化了两步AlN缓冲层的结构,并得到了各向异性更小,晶体质量更好的α面GaN薄膜.分析表明,两步AlN缓冲层中的低温AlN层在减小各向异性中起着关键作用.低温AlN层能抑制了优势方向(c轴)的原子迁移,有利于劣势方向(m轴)的原子迁移,从而减小了Al原子在不同方向迁移能力的差异,并为其后的高温AlN缓冲层和GaN层提供"生长模板",以得到各向异性更小、晶体质量更好的α面GaN材料.  相似文献   

8.
齐维靖  张萌  潘拴  王小兰  张建立  江风益 《物理学报》2016,65(7):77801-077801
采用有机金属化学气相沉积技术在Si(111)衬底上生长蓝光多量子阱发光二极管(LED) 结构, 通过在量子阱下方分别插入两组不同厚度的InGaN/GaN超晶格, 比较了超晶格厚度对LED光电性能的影响. 结果显示: 随超晶格厚度增加, 样品的反向漏电流加剧; 300 K下电致发光仪测得随着电流增加, LED发光光谱峰值的蓝移量随超晶格厚度增加而减少, 但不同超晶格厚度的两个样品在300 K下的电致发光强度几乎无差异. 结合高分辨X射线衍射仪、扫描电子显微镜、透射电子显微镜对样品的位错密度和V形坑特征分析, 明确了两样品反向漏电流产生巨大差异的原因是由于超晶格厚度大的样品具有更大的V形坑和V形坑密度, 而V形坑可作为载流子的优先通道, 使超晶格更厚的样品反向漏电流加剧. 通过对样品非对称(105)面附近的X射线衍射倒易空间图分析, 算得超晶格厚度大的样品其InGaN量子阱在GaN上的弛豫度也大, 即超晶格厚度增加有利于减小InGaN量子阱所受的应力. 综合以上影响LED发光效率的消长因素, 导致两样品最终的发光强度相近.  相似文献   

9.
以直流磁控反应溅射法(RMS)在图形化蓝宝石衬底上制备的AlN薄膜作为缓冲层,采用金属有机化学气相沉积法(MOCVD)外延生长了GaN基LED。与MOCVD生长的低温GaN缓冲层相比,RMS制备的AlN缓冲层具有表面更平整、颗粒更小的形核岛,有利于促进GaN外延的横向生长,减少了形核岛合并时的界面数量和高度差异,降低了缺陷和位错产生的几率。研究结果表明,溅射AlN缓冲层取代传统低温GaN缓冲层后,外延生长的GaN材料具有更高的晶体质量,LED器件在亮度、漏电和抗静电能力等光电特性上均有明显提升。  相似文献   

10.
采用两步AlN缓冲层(一层低温AlN和一层高温AlN)在r面蓝宝石衬底上生长了非极性的α面GaN,并利用高分辨X射线衍射和光致荧光谱对所生长的材料进行了研究.两步AIN缓冲层在我们之前的工作中已被证明比单步高温AlN或低温GaN缓冲层更有利于减小材料各向异性和提高晶体质量,本文进一步优化了两步AlN缓冲层的结构,并得到...  相似文献   

11.
利用金属有机物化学气相淀积技术在蓝宝石衬底上生长了InGaN/GaN量子阱结构. 研究了引入n型InGaN薄层或InGaN/GaN超晶格层的量子阱特性,结果表明通过引入n型InGaN薄层或InGaN/GaN超晶格层缓解了量子阱有源区中的应力,改善了多量子阱表面形貌,减少了V型缺陷密度,而且提高了多量子阱的光致发光强度,从而也改进了LED的发光效率. 关键词: InGaN/GaN多量子阱 原子力显微镜 X射线双晶衍射 光致发光  相似文献   

12.
AlN/GaN superlattice buffer is inserted between GaN epitaxial layer and Si substrate before epitaxial growth of GaN layer. High-quality and crack-free GaN epitaxial layers can be obtained by inserting AlN/GaN superlattice buffer layer. The influence of AlN/GaN superlattice buffer layer on the properties of GaN films are investigated in this paper. One of the important roles of the superlattice is to release tensile strain between Si substrate and epilayer. Raman spectra show a substantial decrease of in-plane tensile strain in GaN layers by using AlN/GaN superlattice buffer layer. Moreover, TEM cross-sectional images show that the densities of both screw and edge dislocations are significantly reduced. The GaN films grown on Si with the superlattice buffer also have better surface morphology and optical properties.  相似文献   

13.
The defect structure of AlGaN/GaN superlattices and GaN layers grown through vapor-phase epitaxy from organometallic compounds is investigated using x-ray diffraction analysis before and after implantation with erbium ions at an energy of 1 MeV and a dose of 3 × 1015 cm?2, as well as after annealing. For a superlattice with a total thickness larger than the implantation depth, the satellites of the superlattice region strained under the action of ions disappear in the x-ray diffraction pattern after annealing at temperatures higher than 900°C. This suggests that the radiation-induced defects responsible for the positive deformation in the layer are annealed at these temperatures. However, annealing even at a temperature of 1050°C does not lead to complete recovery of the initial state and the positive deformation in the remaining regions is caused by residual defects. An analysis of the x-ray diffraction patterns demonstrates that, in samples with thin superlattices located at the depth corresponding to maximum radiation damage, the periodic structure that disappears after implantation at a dose of 3 × 1015 cm?2 is not recovered even after annealing at a temperature of 1050°C. This inference is confirmed by the results of examinations with an electron microscope.  相似文献   

14.
李飙  任艺  常本康 《中国光学》2018,11(4):677-683
利用GaN光电阴极多信息量测试评估系统,对反射式梯度掺杂和均匀掺杂GaN光电阴极样品进行了激活及衰减后的量子效率测试,并测试衰减速率。在同样的衰减时间内,和均匀掺杂样品相比,梯度掺杂样品的衰减比例较小,衰减速率较慢,其原因在于梯度掺杂结构可在其发射层内部产生系列内建电场,致使其能带连续向下弯曲,导致其表面真空能级比均匀掺杂样品下降得更低,发射层表面形成的负电子亲和势更明显,造成发射层内的光生电子更易逸出,阴极量子效率的衰减变慢,从而使其稳定性强于均匀掺杂结构。  相似文献   

15.
氮化蓝宝石衬底上GaN薄膜的微结构与光学性质   总被引:1,自引:0,他引:1  
用透射电子显微镜(TEM),X射线衍射(XRD)和光荧光谱(PL)等测量手段研究了GaN薄膜的微结构和光学性质。样品是用光辐射加热MOCVD在蓝宝石衬底上制备的。随着衬底氮化时间的增加,扩展缺陷的密度显著增加。在位错密度增加一个数量级时,XRD摇摆曲线半宽度(FWHM)由11″增加到15″,PL谱的黄光发射从几乎可忽略增加到带边发射强度的100倍。结合生长条件,我们对黄光与微结构的关系作了讨论。  相似文献   

16.
张金风  许晟瑞  张进成  郝跃 《中国物理 B》2011,20(5):57801-057801
Nonpolar a-plane GaN epilayers are grown on several r-plane sapphire substrates by metal organic chemical vapour deposition using different nucleation layers:(A) a GaN nucleation layer deposited at low temperature(LT);(B) an AlN nucleation layer deposited at high temperature;or(C) an LT thin AlN nucleation layer with an AlN layer and an AlN/AlGaN superlattice both subsequently deposited at high temperature.The samples have been characterized by Xray diffraction(XRD),atomic force microscopy and photoluminescence.The GaN layers grown using nucleation layers B and C show narrower XRD rocking curves than that using nucleation layer A,indicating a reduction in crystal defect density.Furthermore,the GaN layer grown using nucleation layer C exhibits a surface morphology with triangular defect pits eliminated completely.The improved optical property,corresponding to the enhanced crystal quality,is also confirmed by temperature-dependent and excitation power-dependent photoluminescence measurements.  相似文献   

17.
Undoped GaN epilayers were grown on c-plane sapphire substrates under different growth temperatures by metalorganic chemical vapour deposition (MOCVD). The optical and structural characteristics of these grown samples were studied and compared. It was found that the crystalline quality of GaN film deposited at 1050°C was better that of other samples. Photoluminescence spectra showed that the intensities of yellow luminescence band of the samples decreased as the growth temperature increased. All above test results demonstrate that high temperature deposition can serve as a good method for high-quality GaN epilayer growth and there exists an optimal growth temperature.  相似文献   

18.
The human visual system undergoes continuous anatomical, physiological and functional changes throughout the life span. There is also continuous change in the spectral distribution and intensity of light reaching the retina from infancy through senescence, primarily due to changes in the absorption of short-wave light by the lens. Despite these changes in the retinal stimulus and the signals leaving the retina for perceptual analysis, color appearance is relatively stable during aging as measured by broadband reflective or self-luminous samples, the wavelengths of unique blue and yellow, and the achromatic locus. Measures of ocular media density for younger and older observers show, indeed, that color appearance is independent of ocular media density. This may be explained by a renormalization process that was demonstrated by measuring the chromaticity of the achromatic point before and after cataract surgery. There was a shift following cataract surgery (removal of a brunescent lens) that was initially toward yellow in color space, but over the course of months, drifted back in the direction of the achromatic point before surgery. The spatial characteristics of color mechanisms were quantified for younger and older observers in terms of chromatic perceptive fields and the chromatic contrast sensitivity functions. Younger and older observers differed with small spots or with chromatic spatial gratings near threshold, but there were no significant differences with larger spots or suprathreshold spatial gratings.  相似文献   

19.
We grow InN epilayers on different interlayers by metal organic vapour phase epitaxy (MOVPE) method, and investigate the effect of interlayer on the properties and growth mode of InN films. Three InN samples were deposited on nitrided sapphire, low-temperature InN (LT-InN) and high-temperature GaN (HT-GaN), respectively. The InN layer grown directly on nitrided sapphire owns the narrowest x-ray diffraction rocking curve (XRC) width of 300 aresee among the three samples, and demonstrates a two-dimensional (2D) step-flow-like lateral growth mode, which is much different from the three-dimensional (3D) pillar-like growth mode of LT-InN and HT-GaN buffered samples. It seems that mismatch tensile strain is helpful for the lateral epitaxy of InN film, whereas compressive strain promotes the vertical growth of InN films.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号