Impacts of Forced Convection Generated via High Precision Stirring on Scanning Electrochemical Microscopy Experiments in Feedback Mode

In this study, the effects of forced convection on scanning electrochemical microscopy (SECM) experiments in feedback mode using ferrocenemethanol as redox mediator are presented. Forced convection, which enhances the mass transfer inside the system, was generated via an electrical high precision stirrer integrated into the SECM setup. A thin‐film interdigitated array electrode serving as model substrate was investigated with probe scan curves in z‐direction and SECM imaging in constant height mode utilizing ultramicroelectrodes (UME) with diameters (d_probe) of 25 μm and 12.5 μm. It was found that forced convection increased the overall current during SECM imaging without distorting distinctive features of the imaged structure when working with a 25 μm UME at substrate‐to‐tip distances of 14 μm and 11 μm. Furthermore, the electrochemical contrast was improved under hydrodynamic conditions for a substrate‐to‐tip distance of 11 μm and scan rates of 5 μm s^?1, 10 μm s^?1, 20 μm s^?1 and 40 μm s^?1. When further decreasing the gap between the UME and the substrate to 9 μm almost no effects of the forced convection were observed. Consequently, for a 25 μm UME, forced convection led to higher currents and improved performance during SECM experiments in feedback mode at substrate‐to‐tip distances of 14 μm and 11 μm, whereas no effects were observed for a 12.5 μm UME at a distance of 8 μm.     

SECM Studies on the Electrocatalytic Oxidation of Glycerol at Copper Electrodes in Alkaline Medium

This study aims at analyzing the reaction mechanism of the electrooxidation of glycerol at copper surfaces in NaOH solutions using Scanning Electrochemical Microscopy (SECM) in the substrate generation/tip collection (SG/TC) mode. Experiments showed the dependence of the current at the tip on the distance between generator and tip, as well as on the concentration of the NaOH solution. The current at the tip decreased significantly after addition of glycerol, as a result of the competition between diffusion of the free‐soluble Cu(III) species and its consumption during the diffusion in the solution. The determination of the analyte in a castor biodiesel sample employing a single copper microelectrode was carried out.     

In situ electrochemical studies for Li+ ions dissociation from the LiCoO2 electrode by the substrate-generation/tip-collection mode in SECM

This work presents the transportation of Li⁺ ions at the interface of a charging LiCoO₂ electrode through the substrate-generation/tip-collection (SG/TC) feedback mode of scanning electrochemical microscopy (SECM). The TC current, due to the reduction of the ethylene carbonate (EC) supermolecule, is collected more strongly at 1.8 V than that of the Li⁺(DEC) _n at 2.5 V near at the substrate because of the increased concentration of the supermolecule Li⁺(EC)_m, which means that the electrolyte is not uniformly distributed over the substrate. The smooth SG/TC current loop is formed at the probe position optimized by the probe scan curve technique between the LiCoO₂ substrate with 4.0 V and the probe with 1.8 V, which is applied to analyze the Li⁺ ion transport at the interface of the LiCoO₂ electrode. Moreover, the LiCoO₂ substrate, which has a flat surface, is imaged to the nonuniform surface electrochemically by the SECM. We infer that these experimental techniques will help analyze transporting Li⁺ ions at the interface and the electrochemical uniformity of the electrode.     

Analysis of diffusion-controlled stochastic events of iridium oxide single nanoparticle collisions by scanning electrochemical microscopy

We investigated the electrochemical detection of single iridium oxide nanoparticle (IrO(x) NP) collisions at the NaBH(4)-treated Pt ultramicroelectrode (UME) in a scanning electrochemical microscope (SECM) over an insulating surface. The NP collision events were monitored by observing the electrocatalytic water oxidation reaction at potentials where it does not take place on the Pt UME. These collisions occurred stochastically, resulting in a transient response ("blip") for each collision. The frequency of the collisions is proportional to the flux of NPs to the UME tip, and thus equivalent to the SECM current. A plot of collision frequency versus distance followed the theoretical approach curve behavior for negative feedback for a high concentration of mediator, demonstrating that the collisions were diffusion-controlled and that single-particle measurements of mass transport are equivalent to ensemble ones. When the SECM was operated with a Pt substrate at the same potential as the tip, the behavior followed that expected of the shielding mode. These studies and additional ones result in a model where the IrO(x) NP collision on the Pt UME is adsorptive, with oxygen produced by the catalyzed water oxidation causing a current decay. This results in a blip current response, with the current decay diminished in the presence of the oxygen scavenger, sulfite ion. Random walk and theoretical bulk simulations agreed with the proposed mechanism of IrO(x) NP collision, adsorption, and subsequent deactivation.     

The local electrochemical behavior of the AA2098-T351 and surface preparation effects investigated by scanning electrochemical microscopy

In this work, scanning electrochemical microscopy (SECM) measurements were employed to characterize the electrochemical activities on polished and as-received surfaces of the 2098-T351 aluminum alloy (AA2098-T351). The effects of the near surface deformed layer (NSDL) and its removal by polishing on the electrochemical activities of the alloy surface were evaluated and compared by the use of different modes of SECM. Confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM) were also employed to characterize the morphology of the surfaces. The surface chemistry was analyzed by X-ray photoelectron spectroscopy (XPS). The surface generation/tip collection (SG/TC) and competition modes of the SECM were used to study hydrogen gas (H₂) evolution and oxygen reduction reactions, respectively. H₂ evolution and oxygen reduction were more pronounced on the polished surfaces. The feedback mode of SECM was adopted to characterize the electrochemical activity of the polished surface that was previously corroded by immersion in a chloride-containing solution, in order to investigate the influence of the products formed on the active/passive domains. The precorroded surface and as-received surfaces revealed lower electrochemical activities compared with the polished surface showing that either the NSDL or corrosion products largely decreased the local electrochemical activities at the AA2098-T351 surfaces.     

Scanning electrochemical microscopic study of hydrogen oxidation and evolution at electrochemically deposited pt nanoparticulate electrode incorporated in polyaniline.

Scanning Electrochemical Microscopy (SECM) feedback mode and substrate generation-tip collection (SG-TC) mode coupled with chronoamperometric approach were used to investigate H2 oxidation and hydrogen evolution reaction (HER) at a polyaniline (PAni) coated highly oriented pyrolytic graphite (HOPG) electrode. Using the former mode, the heterogeneous electron transfer (ET) kinetics for H2 oxidation was studied, while the latter mode allowed mapping of the distribution of local [H2] at the nanoparticulate/aqueous interface, followed by monitoring the transients at the tip. These preliminary studies demonstrate that SECM is useful in evaluating the activity of nanophase electrocatalysts. Particularly, if one employs nanometer-sized tips or hydrodynamic microjet electrodes where the mass transfer rate is significantly high, it should be possible to investigate the ET kinetics more accurately.     

Modeling steady-state experiments with a scanning electrochemical microscope involving several independent diffusing species using the boundary element method

The BEM algorithm developed earlier for steady-state experiments in the scanning electrochemical microscopy (SECM) feedback mode has been expanded to allow for the treatment of more than one independently diffusing species. This allows the treatment of substrate-generation/tip-collection SECM experiments. The simulations revealed the interrelation of sample layout, local kinetics, imaging conditions, and the quality of the obtained SECM images. Resolution in the SECM SG/TC images has been evaluated, and it depends on several factors. For most practical situations, the resolution is limited by the diffusion profiles of the sample. When a dissolved compound is converted at the sample (e.g., oxygen reduction or enzymatic reaction at the sample), the working distance should be significantly larger than in SECM feedback experiments (ca. 3 r(T) for RG = 5) in order to avoid diffusional shielding of the active regions on the sample by the UME body. The resolution ability also depends on the kinetics of the active regions. The best resolution can be expected if all the active regions cause the same flux. In one simulated example, which might mimic a possible scenario of a low-density protein array, considerable compromises in the resolving power, were noted when the flux from two neighboring spots differs by more than a factor of 2.     

Solid Contact Micropipette Ion Selective Electrode for Potentiometric SECM

New solid contact ammonium micropipette electrodes (ISE), well applicable in scanning electrochemical microscopy are reported. The solid contact was made of a PEDOT nanowire coated carbon fiber, lowered down close to the orifice, and dipped inside the cocktail being in the pipette tip. This configuration provided low electrical resistance and good potential stability. Submicron tip size, usual in case of micropipette ISE‐s easily can be fabricated in this way. The applicability of the electrode in SECM has been proved in SG/TC mode imaging urease enzyme active spots in urea solutions.     

The cavity-microelectrode as a tip for scanning electrochemical microscopy

In this work, we present and discuss the use of cavity-microelectrodes (C-MEs) used as tip for the scanning electrochemical microscopy (SECM). Cavity-microelectrodes can be filled with a desired finely dispersed material thus compensating for the limited commercial availability of microwires. After discussing the possibility of filling and emptying a cavity-microelectrode with a desired tip shape, the consistency of negative and positive feedback approach curves obtained after filling a Au C-ME was verified. In addition, the tip/C-ME was tested under gas (oxygen) evolution condition, in order to demonstrate that the filling is stable in a wide range of gas fluxes thus extending the possible applications to tip generation/substrate collection mode. Finally, we introduce the use of the proposed system to quantify the rates of parallel reactions occurring at the material inserted in the tip under the tip generation/substrate collection mode.     

Ex Situ Scanning Electrochemical Microscopy (SECM) Investigation of Bismuth‐ and Bismuth/Lead Alloy Film‐Modified Gold Electrodes in Alkaline Medium

Scanning electrochemical microscopy (SECM) in feedback mode was employed to characterise the reactivity and microscopic peculiarities of bismuth and bismuth/lead alloys plated onto gold disk substrates in 0.1 mol L^?1 NaOH solutions. Methyl viologen was used as redox mediator, while a platinum microelectrode was employed as the SECM tip. The metal films were electrodeposited ex situ from NaOH solutions containing either bismuth ions only or both bismuth and lead ions. Approach curves and SECM images indicated that the metal films were conductive and locally reactive with oxygen to provide Bi³⁺ and Pb²⁺ ions. The occurrence of the latter chemical reactions was verified by local anodic stripping voltammetry (ASV) at the substrate solution interface by using a mercury‐coated platinum SECM tip. The latter types of measurements allowed also verifying that lead was not uniformly distributed onto the bismuth film electrode substrate. These findings were confirmed by scanning electron microscopy images. The surface heterogeneity produced during the metal deposition process, however, did not affect the analytical performance of the bismuth coated gold electrode in anodic stripping voltammetry for the determination of lead in alkaline media, even in aerated aqueous solutions. Under the latter conditions, stripping peak currents proportional to lead concentration with a satisfactory reproducibility (within 5 % RSD) were obtained.     

Mathematical Modelling of the Influence of Ultra‐micro Electrode Geometry on Approach Curves Registered by Scanning Electrochemical Microscopy

Scanning electrochemical microscopy (SECM) is an emerging electroanalytical sensing technique, used to investigate the electrochemical properties of the sample by ultra‐micro‐electrode(UME) scanning probe. UME signal usually is the current, which depends not only on the properties of the evaluated system but also on UME characteristics such as geometry. Variations of UME geometry can decrease accuracy of the measurement, and then correct analysis of the SECM data becomes almost impossible. In the present work, we studied the precision of measurements with three different the most frequent types of defected UME's ((i) recessed‐UME, (ii) outwarded‐UME, (iii) cone‐UME). Measurement results were compared with that obtained with not defected standard‐plane‐UME. Computational experiment was performed with SECM model using diffusion equations with non‐rectangular border conditions to calculate estimated currents for these three types of defected UMEs and to compare them with that for standard‐plane‐UME. In order to test the correctness of the model, computations for recessed‐UME model were compared with data of real‐recessed‐UME experiment.     

Measurement of apparent diffusion coefficients within ultrathin nafion Langmuir-Schaefer films: comparison of a novel scanning electrochemical microscopy approach with cyclic voltammetry

The use of scanning electrochemical microscopy (SECM) to evaluate the apparent diffusion coefficient, Dapp, of redox-active species in ultrathin Nafion films is described. In this technique, an ultramicroelectrode (UME) tip, positioned close to a film on a macroscopic electrode, is used to oxidize (or reduce) a species in bulk solution, causing the tip-generated oxidant (reductant) to diffuse to the film/solution interface. The oxidation (reduction) of film-confined species regenerates the reductant (oxidant) in solution, leading to feedback to the UME. A numerical model is developed that allows Dapp to be determined. For these studies, ultrathin films of Nafion were prepared using the Langmuir-Schaefer (LS) technique and loaded with an electroactive species, either the ferrocene derivative ferrocenyltrimethylammonium cation, FA+, or tris(2,2'-bipyridyl)ruthenium(II), Ru(bpy)32+. The morphology and the thickness of the Nafion LS films (1.5 +/- 0.2 nm per layer deposited) were evaluated using atomic force microscopy (AFM). For comparison with the SECM measurements, cyclic voltammetry (CV) was employed to evaluate the concentration of electroactive species within the Nafion LS films and to determine Dapp. The latter was found to be essentially invariant with film thickness, but the value for Ru(bpy)32+ was 1 order of magnitude larger than for FA+. CV and SECM measurements yield different values of Dapp, and the underlying reasons are discussed. In general, the Dapp values for these films are considerably smaller than for recast Nafion films, which can be attributed to the compactness of Nafion LS films. Nonetheless, the ultrathin nature of the films leads to fast response times, and we thus expect that these modified electrodes could find applications in sensing, electroanalysis, and electrocatalysis.     

Polymer films on electrodes: investigation of ion transport at poly(3,4-ethylenedioxythiophene) films by scanning electrochemical microscopy

Electropolymerization, morphology characterization, and ion transport of poly(3,4-ethylenedioxythiophene) (PEDOT) films doped with different counterions (chloride, ferrocyanide (FCN), and poly(p-styrenesulfonate) (PSS-)) on a platinum electrode were investigated using scanning electrochemical microscopy (SECM) during both potential step (chronocoulometric) and cyclic voltammetric scans. An ultramicroelectrode (UME) tip was positioned close to the surface of a PEDOT-modified substrate electrode, and the responses of both electrodes to a substrate potential step or linear sweep were monitored simultaneously. Chloride or ferrocyanide (FCN) ejection during PEDOT reduction was shown to be a function of the reduction potential. The nature of the cation in the bulk solution was not found to be important in the kinetics of ion transport in PEDOT+/FCN- films. Direct evidence for the incorporation of cations of Ru(NH3)6(3+/2+) in a PEDOT film during its reduction was also obtained by SECM measurements. The adsorption of Ru(NH3)6(3+) in fully oxidized PEDOT+/PSS- films was observed and attributed to ion exchange between the Na+ co-ion of PSS- and Ru(NH3)6(3+) in the bulk solution.     

Fabrication of Active Horseradish Peroxidase Micropatterns with a High Resolution by Scanning Electrochemical Microscopy

We used a new reactive species OH^? to fabricate active horseradish peroxidase (HRP) micropatterns with a high resolution by scanning electrochemical microscopy (SECM) coupled with a carbon fiber disk electrode as the SECM tip. In this method, except for active HRP micropatterns predesigned other regions on a HRP‐immobilized substrate were deactivated by OH^? generated at the tip held at ?1.7 V in 1.0 mol/L KCl containing 2.0×10^?3 mol/L benzoquinone (BQ) (pH 8.0). The feedback mode of SECM with a tip potential of ?0.2 V was used to characterize the active HRP micropatterns in 1.0 mol/L KCl containing 2.0×10^?3 mol/L BQ and 2.0×10^?3 mol/L H₂O₂.     

Scanning Electrochemical Microscopy (SECM) Based Detection of Oligonucleotide Hybridization and Simultaneous Determination of the Surface Concentration of Immobilized Oligonucleotides on Gold

The direct mode of scanning electrochemical microscopy (SECM) was used for the local deposition of oligonucleotide (ODN) patterns on thin gold films and the generation‐collection (GC) mode was applied for the determining the amount of surface‐accessible oligonucleotides. The local deposition was achieved through the micrometer‐sized formation of a conducting polymer bearing 15^mer single‐stranded oligonucleotide strands. After the interaction of the oligonucleotide with its biotin‐labeled complimentary strand, streptavidin was bound. The molecular assembly was completed by linking biotin‐labeled β‐galactosidase from Escherichia coli to the streptavidin. The activity of the linked β‐galactosidase was mapped with SECM in the GC mode by monitoring the oxidation of p‐aminophenol (PAP) formed in the enzyme‐catalyzed hydrolysis of p‐aminophenyl‐β‐D ‐galactopyranoside. The feedback effect due to recycling of the reaction product at the gold surface was analyzed. It was shown experimentally that this effect becomes insignificant at ultramicroelectrode (UME)‐substrate distances larger than 3 UME radii. The flux of formed PAP allowed the determination the surface density of accessible oligonucleotide strands in the functionalized polymer. It was shown that that thicker pyrrole/ODN–Pyrrole polymer films do not lead to a significantly increased accessible ODN surface concentration.     

Surface analysis by scanning electrochemical microscopy: resolution studies and applications to polymer samples

Resolution studies of scanning electrochemical microscopy (SECM) have been performed in the feedback mode and in the generator/collector mode at circular model structures. A quantitative correlation of the loss in resolution and the increase in distance between tip and sample is found. Measuring a band electrode of just 500 nm width, the high sensitivity of the SECM in identifying chemically active sites is proven. Applied to polymer samples, the chemical composition was determined in the feedback mode at high lateral resolution. The difference in electrical conductivity allows one to distinguish between doped and undoped parts of a polyaniline film. By scanning above a blend consisting of polypyrrole and polypropylene, a map of the local chemical composition was obtained. In this context, the influence of the tip overpotential on the image is discussed.     

Imaging of enzyme activity by scanning electrochemical microscope equipped with a feedback control for substrate-probe distance

The enzymatic activity of diaphorase (Dp) immobilized on a solid substrate was characterized using a scanning electrochemical microscope (SECM) with shear force feedback to control the substrate-probe distance. The shear force between the substrate and the probe was monitored with a tuning fork-type quartz crystal and used as the feedback control to set the microelectrode probe close to the substrate surface. The sensitivity and the contrast of the SECM image were improved in the constant distance mode (distance, 50 nm) with the shear force feedback compared to the image in the constant height mode without the feedback. By using this system, the SECM and topographic images of the immobilized diaphorase were simultaneously measured. The microelectrode tip used in this study was ground aslant like a syringe needle in order to obtain the shaper topographic images. This shape was also effective for avoiding the interference during the diffusion of the enzyme substrates.     

Imaging Local Proton Fluxes through a Polycarbonate Membrane by Using Scanning Electrochemical Microscopy and Functionalized Alkanethiols

A new application of scanning electrochemical microscopy (SECM) to probe the transport of protons through membranes is described. Herein, a probe ultramicroelectrode (UME) is modified with a self‐assembled monolayer (SAM) of 11‐mercaptoundecanoic acid to qualitatively image areas within different pH regions above a track‐etched membrane. The current response of the modified electrode in the presence of potassium hexacyanoferrate as electroactive component is different in acidic and alkaline solutions. Depending on the pH value of the solution, the SAM‐covered electrode exposes either a neutral or a negatively charged insulating monolayer at pH 3 or 7, respectively, which leads to an increase/decrease in the faradaic current due to electrostatic interactions between the neutral/charged surface and the charged redox mediator. Therefore, local pH changes in the close vicinity of a membrane‐like substrate lead to different current responses recorded at the tip electrode when scanning above the surface.     

Detection of hydrogen peroxide produced at a liquid/liquid interface using scanning electrochemical microscopy

Scanning electrochemical microscopy (SECM) was used to monitor in situ hydrogen peroxide (H₂O₂) produced at a polarized water/1,2-dichloroethane (DCE) interface. The water/DCE interface was formed between a DCE droplet containing decamethylferrocene (DMFc) supported on a solid electrode and an acidic aqueous solution. H₂O₂ was generated by reducing oxygen with DMFc at the water/DCE interface, and was detected with a SECM tip positioned in the vicinity of the interface using a substrate generation/tip collection mode. This work shows unambiguously how the H₂O₂ generation depends on the polarization of the liquid/liquid interface, and how proton-coupled electron transfer reactions can be controlled at liquid/liquid interfaces.     

Electro‐oxidation and reduction of H2 on platinum studied by scanning electrochemical microscopy for the purpose of local detection of H2 evolution

Electrochemical detection of H₂ using scanning electrochemical microscopy (SECM) has shown to hold great promise as a sensitive characterization method with high spatial resolution for active surfaces generating H₂. Herein, the factors contributing to the current that is measured by SECM in generation/collection mode for H₂ detection are studied. In particular, the concentration gradient of H₂ at the substrate, the H₂/H⁺ recycling between the SECM tip and substrate and hemispherical profile of H₂ diffusion has been discussed. It was postulated that H₂/H⁺ recycling plays a dominant role in the oxidative current measured in generation/collection mode of SECM when the microelectrode is positioned in close vicinity of substrate. Copyright © 2015 John Wiley & Sons, Ltd.