Precise Tuning of Surface Composition and Electron‐Transfer Properties of Graphene Oxide Films through Electroreduction

Graphene materials are generally prepared from the exfoliation of graphite oxide (GO) to graphene oxide, followed by subsequent chemical or thermal reduction. These methods, although efficient in removing most of the oxygen functionalities from the GO material, lack control over the extent of the reduction process. We demonstrate here an electrochemical reduction procedure that not only allows for precise control of the reduction process to obtain a graphene material with a well‐defined C/O ratio in the range of 3 to 10, but also one that is able to tune the electrocatalytic properties of the reduced material. A method that is able to precisely control the amount and density of the oxygen functionalities on the graphene material as well as its electrochemical behaviour is very important for several applications such as electronics, bio‐composites and electrochemical devices.     

One‐Step Electrodeposition to Layer‐by‐Layer Graphene–Conducting‐Polymer Hybrid Films

One‐step fabrication of graphene–polyaniline (graphene–PANI) hybrid film was facilely achieved by cyclic voltammetric electrolysis of a bath containing both graphene oxide (GO) and aniline, where graphene is obtained by electrochemical reduction of GO and PANI is simultaneously obtained by aniline electropolymerization. As there is no strong attraction between aniline and GO under the electrodeposition conditions, the independent depositions of PANI and reduced GO nanosheets at their greatly differed potentials led to alternate layered graphene–PANI films, with the topmost layer being PANI particles or graphene sheets just by changing the initial scan directions. The two kinds of graphene–PANI hybrid films present excellent but different electrical and electrochemical behaviors.     

Concise,Single‐Step Synthesis of Sulfur‐Enriched Graphene: Immobilization of Molecular Clusters and Battery Applications

The concise synthesis of sulfur‐enriched graphene for battery applications is reported. The direct treatment of graphene oxide (GO) with the commercially available Lawesson's reagent produced sulfur‐enriched‐reduced GO (S‐rGO). Various techniques, such as X‐ray photoelectron spectroscopy (XPS), confirmed the occurrence of both sulfur functionalization and GO reduction. Also fabricated was a nanohybrid material by using S‐rGO with polyoxometalate (POM) as a cathode‐active material for a rechargeable battery. Transmission electron microscopy (TEM) revealed that POM clusters were individually immobilized on the S‐rGO surface. This battery, based on a POM/S‐rGO complex, exhibited greater cycling stability for the charge‐discharge process than a battery with nanohybrid materials positioned between the POM and nonenriched rGO. These results demonstrate that the use of sulfur‐containing groups on a graphene surface can be extended to applications such as the catalysis of electrochemical reactions and electrodes in other battery systems.     

Single‐Step Functionalization and Exfoliation of Graphene with Polymers under Mild Conditions

The simultaneous polymer functionalization and exfoliation of graphene sheets by using mild bath sonication and heat treatment at low temperature is described. In particular, free‐radical polymerization of three different vinyl monomers takes place in the presence of graphite flakes. The polymerization procedure leads to the exfoliation of graphene sheets and at the same time the growing polymer chains are attached onto the graphene lattice, which gives solubility and stability to the final graphene‐based hybrid material. The polymer‐functionalized graphene sheets possess fewer defects as compared with previously reported polymer‐functionalized graphene. The success of the covalent functionalization and exfoliation of graphene was confirmed by using a variety of complementary spectroscopic, thermal, and microscopy techniques, including Raman, IR and UV/Vis spectroscopy, thermogravimetric analysis, and transmission electron microscopy.     

Thiol–Yne Click Reactions on Alkynyl–Dopamine‐Modified Reduced Graphene Oxide

The large‐scale preparation of graphene is of great importance due to its potential applications in various fields. We report herein a simple method for the simultaneous exfoliation and reduction of graphene oxide (GO) to reduced GO (rGO) by using alkynyl‐terminated dopamine as the reducing agent. The reaction was performed under mild conditions to yield rGO functionalized with the dopamine derivative. The chemical reactivity of the alkynyl function was demonstrated by post‐functionalization with two thiolated precursors, namely 6‐(ferrocenyl)hexanethiol and 1H,1H,2H,2H‐perfluorodecanethiol. X‐ray photoelectron spectroscopy, UV/Vis spectrophotometry, Raman spectroscopy, conductivity measurements, and cyclic voltammetry were used to characterize the resulting surfaces.     

Synthesis of polydopamine‐coated graphene–polymer nanocomposites via RAFT polymerization

Graphene‐polymer nanocomposites have significant potential in many applications such as photovoltaic devices, fuel cells, and sensors. Functionalization of graphene is an essential step in the synthesis of uniformly distributed graphene‐polymer nanocomposites, but often results in structural defects in the graphitic sp² carbon framework. To address this issue, we synthesized graphene oxide (GO) by oxidative exfoliation of graphite and then reduced it into graphene via self‐polymerization of dopamine (DA). The simultaneous reduction of GO into graphene, and polymerization and coating of polydopamine (PDA) on the reduced graphene oxide (RGO) surface were confirmed with XRD, UV–Vis, XPS, Raman, TGA, and FTIR. The degree of reduction of GO increased with increasing DA/GO ratio from 1/4 to 4/1 and/or with increasing temperature from room temperature to 60 °C. A RAFT agent, 2‐(dodecylthiocarbonothioylthio)?2‐methylpropionic acid, was linked onto the surface of the PDA/RGO, with a higher equivalence of RAFT agent in the reaction leading to a higher concentration of RAFT sites on the surface. Graphene‐poly(methyl methacrylate), graphene‐poly(tert‐butyl acrylate), and graphene‐poly(N‐isopropylacrylamide) nanocomposites were synthesized via RAFT polymerization, showing their characteristic solubility in several different solvents. This novel synthetic route was found facile and can be readily used for the rational design of graphene‐polymer nanocomposites, promoting their applications. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3941–3949     

On Oxygen‐Containing Groups in Chemically Modified Graphenes

Reduced graphenes (belonging to the class of chemically modified graphenes, CMG) are one of the most investigated and utilized materials in current research. Oxygen functionalities on the CMG surfaces have dramatic influences on material properties. Interestingly, these functionalities are rarely comprehensively characterized. Herein, the four most commonly used CMGs, mainly electrochemically reduced graphene oxide (ER‐GO), thermally reduced graphene oxide (TR‐GO), and the corresponding starting materials, that is, graphene oxide and graphite oxide, were comprehensively characterized by a wide variety of methods, such as high‐resolution X‐ray photoelectron spectroscopy, electrochemical impedance spectroscopy, UV/Vis spectroscopy, transmission electron microscopy (TEM), and voltammetry, to establish connections between the structures of these materials that carry different oxygen functionalities and their electrochemical behaviors. This was followed by the quantification of the negatively charged oxygen‐containing groups (OCGs) by UV/Vis spectroscopy and of the electrochemically reducible OCGs by voltammetry. Lastly, a biofunctionalization with gold nanoparticle (AuNP)‐modified DNA sequences was performed by the formation of covalent bonds with the carboxylic groups (? COOH) on the CMG surfaces. There was an evident predominance of functionalizable ? COOH groups on the ER‐GO surface, as confirmed by a higher amount of Au detected both with differential‐pulse voltammetry and impedance spectroscopy, coupled with visualization by TEM. We exploited the DNA–Au bioconjugates as highly specific stains to localize and visualize the positions of carboxylic groups. Our findings are very important to clearly identify the presence, nature, and distribution of oxygen functionalities on different chemically modified graphenes.     

Preparing graphene oxide–copper composite material from spent lithium ion batteries and catalytic performance analysis

The wide use of lithium ion batteries (LIBs) has created much waste, which has become a global issue. It is vital to recycle waste LIBs considering their environmental risks and resource characteristics. Anode graphite from spent LIBs still possess a complete layer structure and contain some oxygen-containing groups between layers, which can be reused to prepare high value-added products. Given the intrinsic defect structure of anode graphite, copper foils in LIB anode electrodes, and excellent properties of graphene, graphene oxide–copper composite material was prepared in this work. Anode graphite was firstly purified to remove organic impurities by calcination and remove lithium. Purified graphite was used to prepare graphene oxide–copper composite material after oxidation to graphite oxide, ultrasonic exfoliation to graphene oxide (GO), and Cu²⁺ adsorption. Compared with natural graphite, preparing graphite oxide using anode graphite consumed 40% less concentrated H₂SO₄ and 28.6% less KMnO₄. Cu²⁺ was well adsorbed by 1.0 mg L^?1 stable GO suspension at pH 5.3 for 120 min. Graphene oxide–copper composite material could be successfully obtained after 6 h absorption, 3 h bonding between GO and Cu²⁺ with 3/100 of GO/CuSO₄ mass ratio. Compared to CuO, graphene oxide–copper composite material had better catalytic photodegradation performance on methylene blue, and the electric field further improved the photodegradation efficiency of the composite material.     

Capillary zone electrophoresis of graphene oxide and chemically converted graphene

The preparation of processable graphene oxide colloids called chemically converted graphene (CCG) involves the following steps: oxidation of graphite to form graphite oxide; exfoliation of graphite oxide to form graphene oxide (GO); and reduction of GO to form CCG. In this work, the exfoliation and reduction steps were monitored by capillary zone electrophoresis (CZE). CZE was performed in fused silica capillaries with UV absorbance at 230 nm (GO) and 270 nm (CCG) using 250 μM tetrapropylammonium hydroxide (pH 10.4). The results indicate that almost complete exfoliation of graphite oxide (0.05 wt%) and higher recovery of CCG were obtained by sonication at 50% power for more than 15 h. CZE is considered a valuable tool for the fractionation and analysis of GO nanoparticles and, hence, for the control of different steps in preparation of CCG.     

功能型单层石墨烯的热剥离法制备及其超电容性能

以氧化石墨(GO)作为前驱体,在两种不同热剥离温度下制备了两类功能型单层石墨烯.其中第一类功能型单层石墨烯通过在较低温度及空气气氛下热剥离GO制备;第二类功能型单层石墨烯通过在氮气保护下高温热剥离GO得到;利用氮气吸附-脱附方法测定了两类样品的比表面积,利用电化学测试方法分析了其超电容性能.结果表明,通过低温热剥离的方式即可以有效剥离GO;两类样品均具有较高的BET比表面积.低温热剥离GO所制备的功能型单层石墨烯在2 mol/L KOH体系中的最大比电容值约为220 F/g;而通过高温热剥离GO所制备的功能型单层石墨烯虽然同样具有较高的BET比表面积,但其最大比电容值下降至约150 F/g.这表明通过低温热剥离GO所制备的功能型单层石墨烯具有更优异的超电容性能.     

Self‐Construction from 2D to 3D: One‐Pot Layer‐by‐Layer Assembly of Graphene Oxide Sheets Held Together by Coordination Polymers

Deposition of Ni‐based cyanide bridged coordination polymer (NiCNNi) flakes onto the surfaces of graphene oxide (GO) sheets, which allows precise control of the resulting lamellar nanoarchitecture by in situ crystallization, is reported. GO sheets are utilized as nucleation sites that promote the optimized crystal growth of NiCNNi flakes. The NiCNNi‐coated GO sheets then self‐assemble and are stabilized as ordered lamellar nanomaterials. Regulated thermal treatment under nitrogen results in a Ni₃C–GO composite with a similar morphology to the starting material, and the Ni₃C–GO composite exhibits outstanding electrocatalytic activity and excellent durability for the oxygen reduction reaction.     

Free‐Radical‐Promoted Conversion of Graphite Oxide into Chemically Modified Graphene

The preparation of chemically modified graphene (CMG) generally involves the reduction of graphite oxide (GO) by using various reducing reagents. Herein, we report a free‐radical‐promoted synthesis of CMG, which does not require any conventional reductant. We demonstrated that the phenyl free radical can efficiently promote the conversion of GO into CMG under mild conditions and produces phenyl‐functionalized CMG. This pseudo‐“reduction” process is attributed to a free‐radical‐mediated elimination of the surface‐attached oxygen‐containing functionalities. This work illustrates a new strategy for preparing CMG that is alternative to the conventional means of chemical reduction. Furthermore, the phenyl‐functionalized graphene shows an excellent performance as an electrode material for lithium‐battery applications.     

Cross‐sectional structural characterization of the surface of exfoliated HOPG using HRTEM‐EELS

We analyzed the surface atomic structure of highly oriented pyrolytic graphite (HOPG) substrate exfoliated with adhesive tape, using high‐resolution transmission electron microscopy and scanning transmission electron microscopy‐electron energy‐loss spectroscopy (STEM‐EELS). The surface step height of the exfoliated HOPG substrate was determined using high‐angle annular dark‐field‐scanning transmission electron microscopy (HAADF‐STEM) images and the depth profiles of the EELS spectra of a cross‐sectioned thin foil specimen prepared via focused ion beam milling. The exfoliated surface of the HOPG substrate presented disordered and curved graphene layers. The STEM‐EELS measurements indicated that upon exfoliation, the surface of the HOPG substrate reacted with atmospheric water and oxygen molecules.     

Adsorption of Zn(II) on graphene oxide prepared from low‐purity of amorphous graphite

The adsorption of Zn(II) in aqueous solutions on graphene oxide (GO) prepared from low‐purity of natural amorphous graphite has been studied in this work. The study was performed through the measurements of Zeta potential, atomic force microscope, Fourier transform infrared spectrum and X‐ray photoelectron spectroscopy. The results indicated that the adsorption followed the Langmuir model with the maximum Zn(II) adsorption capacity of 73 mg/g at pH 7.0. In addition, the adsorption was well described by the pseudo‐second‐order kinetics model. The mechanism of the Zn(II) adsorption on GO was mainly attributed to chemical adsorption through complexation reaction between Zn(II) and hydroxyl or carboxyl groups on the GO sheets, while the electrostatic interaction also contribute to the whole interaction. Copyright © 2016 John Wiley & Sons, Ltd.     

A Catalytic Microwave Process for Superfast Preparation of High‐Quality Reduced Graphene Oxide

Herein we report that a small amount of graphite can unexpectedly act as the catalyst to greatly promote the microwave exfoliation and reduction of graphite oxide in ambient air. The reaction can be finished in a few seconds in contrast to more than ten minutes without catalyst. The catalytic microwave exfoliated graphite oxide (CMEGO) is of higher quality than the traditional microwave exfoliated graphite oxide, including a much higher exfoliation degree with thinner graphene sheets and higher specific surface area (886 m² g⁻¹ vs. 466 m² g⁻¹), a much larger C/O ratio (19.4 vs. 6.3) and a higher lattice crystallinity, as well as significantly improved electrical conductivity (53180 S m⁻¹ vs. 5140 S m⁻¹). The CMEGO is used as anode for lithium‐ion battery (LIB) and sodium‐ion battery (SIB), and delivers ultrahigh reversible capacities, remarkable rate capabilities, and superior cycling stabilities in both LIB and SIB.     

Graphene Oxides Prepared by Hummers’, Hofmann’s,and Staudenmaier’s Methods: Dramatic Influences on Heavy‐Metal‐Ion Adsorption

Graphene oxide (GO), an up‐and‐coming material rich in oxygenated groups, shows much promise in pollution management. GO is synthesised using several synthetic routes, and the adsorption behaviour of GO is investigated to establish its ability to remove the heavy‐metal pollutants of lead and cadmium ions. The GO is synthesised by Hummers’ (HU), Hofmann’s (HO) and Staudenmaier’s (ST) methodologies. Characterisation of GO is performed before and after adsorption experiments to investigate the structure–function relationship by using Fourier‐transform infrared spectroscopy and X‐ray photoelectron spectroscopy. Scanning electron microscopy coupled with elemental detection spectroscopy is used to investigate morphological changes and heavy‐metal content in the adsorbed GO. The filtrate, collected after adsorption, is analysed by inductively coupled plasma mass spectrometry, through which the efficiency and adsorption capacity of each GO for heavy‐metal‐ion removal is obtained. Spectroscopic analysis and characterisation reveal that the three types of GO have different compositions of oxygenated carbon functionalities. The trend in the affinity towards both Pb^II and Cd^II is HU GO>HO GO>ST GO. A direct correlation between the number of carboxyl groups present and the amount of heavy‐metal ions adsorbed is established. The highest efficiency and highest adsorption capacity of heavy‐metal ions is achieved with HU, in which the relative abundance of carboxyl groups is highest. The embedded systematic study reveals that carboxyl groups are the principal functionality responsible for heavy‐metal‐ion removal in GO. The choice of synthesis methodology for GO has a profound influence on heavy‐metal‐ion adsorption. A further enrichment of the carboxyl groups in GO will serve to enhance the role of GO as an adsorbent for environmental clean‐up.     

Synthesis of polystyrene nanoparticles “armoured” with nanodimensional graphene oxide sheets by miniemulsion polymerization

Polystyrene particles “armoured” with nanosized graphene oxide (GO) sheets have been prepared by aqueous miniemulsion polymerization of styrene, exploiting the amphiphilic properties of GO in the absence of conventional surfactants. The nanoscale GO sheets were prepared from graphite nanofibers of diameter approximately 100 nm based on a novel procedure, thus effectively ensuring the absence of larger sheets. Polymerization proceeded to high conversion with minor coagulation, with final number‐average particle diameters of approximately 500 nm, but relatively broad particle size distributions. Scanning electron microscopy analysis revealed particles with a textured surface, consistent with the expected morphology. Interestingly, analysis of GO sheets recovered from the polymerization revealed that the GO sheets are partially reduced during the polymerization—approximately 50% of the initial carboxyl groups of the GO were lost, consistent with some loss in colloidal stability at high conversion. The overall approach offers a convenient and attractive synthetic route to novel graphene‐based polymeric nanostructures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Functionalization of graphene oxide towards thermo‐sensitive nanocomposites via moderate in situ SET‐LRP

A mild and efficient strategy is presented for growing thermo‐sensitive polymers directly from the surface of exfoliated graphene oxide (GO). This method involves the covalent attachment of Br‐containing initiating groups onto the surface of GO sheets followed by in situ growing poly[poly(ethylene glycol) ethyl ether methacrylate] (PPEGEEMA) via single‐electron‐transfer living radical polymerization (SET‐LRP). Considering the lack of reactive functional groups on the surface of GO, exfoliated GO sheets were subjected to an epoxide ring opening reaction with tris(hydroxymethyl) aminomethane (TRIS) at room temperature. The initiating groups were grafted onto TRIS‐GO sheets by treating hydroxyls with 2‐bromo‐2‐methylpropionyl bromide at room temperature. PPEGEEMA chains were synthesized by in situ SET‐LRP using CuBr/Me₆TREN as catalytic system at 40 °C in H₂O/THF. The resulting materials were characterized using a range of testing techniques and it was proved that polymer chains were successfully introduced to the surface of GO sheets. After grafting with PPEGEEMA, the modified GO sheets still maintained the separated single layers and the dispersibility was significantly improved. This TRIS‐GO‐PPEGEEMA hybrid material shows reversible self‐assembly and deassembly in water by switching temperature at about 34 °C. Such smart graphene‐based materials promise important potential applications in thermally responsive nanodevices and microfluidic switches. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Functional Graphene by Thiol‐ene Click Chemistry

Thiol‐ene click reaction was successfully employed for chemical modification of graphene oxide (GO) by one‐step synthesis. Herein, 2,2‐azobis(2‐methylpropionitrile) (AIBN) was used as thermal catalyst and cysteamine hydrochloride (HS?(CH₂)₂?NH₂HCl) was used as thiol‐containing compound, which is incorporated to GO surface upon reaction with the C=C bonds. The hydrochloride acts as protecting group for the amine, which is finally eliminated by adding sodium hydroxide. The modified GO contains both S‐ and N‐containing groups (NS‐GO). We found that NS‐GO sheets form good dispersion in water, ethanol, and ethylene glycol. These graphene dispersions can be processed into functionalized graphene film. Besides, it was demonstrated that NS‐GO was proved to be an excellent host matrix for platinum nanoparticles. The developed method paves a new way for graphene modification and its functional nanocomposites.     

Facile Mechanochemical Synthesis of Nano SnO2/Graphene Composite from Coarse Metallic Sn and Graphite Oxide: An Outstanding Anode Material for Lithium‐Ion Batteries

A facile method for the large‐scale synthesis of SnO₂ nanocrystal/graphene composites by using coarse metallic Sn particles and cheap graphite oxide (GO) as raw materials is demonstrated. This method uses simple ball milling to realize a mechanochemical reaction between Sn particles and GO. After the reaction, the initial coarse Sn particles with sizes of 3–30 μm are converted to SnO₂ nanocrystals (approximately 4 nm) while GO is reduced to graphene. Composite with different grinding times (1 h 20 min, 2 h 20 min or 8 h 20 min, abbreviated to 1, 2 or 8 h below) and raw material ratios (Sn:GO, 1:2, 1:1, 2:1, w/w) are investigated by X‐ray diffraction, X‐ray photoelectron spectroscopy, field‐emission scanning electron microscopy and transmission electron microscopy. The as‐prepared SnO₂/graphene composite with a grinding time of 8 h and raw material ratio of 1:1 forms micrometer‐sized architected chips composed of composite sheets, and demonstrates a high tap density of 1.53 g cm^?3. By using such composites as anode material for LIBs, a high specific capacity of 891 mA h g^?1 is achieved even after 50 cycles at 100 mA g^?1.