Fabrication of Miniaturised Screen‐printed Glucose Biosensors,Using a Water‐based Ink,and the Evaluation of their Electrochemical Behaviour

This paper describes a simple, convenient approach to the fabrication of microband electrodes and microband biosensors based on screen printing technology. These devices were printed in a three‐electrode configuration on one strip; a silver/silver chloride electrode and carbon counter electrode served as reference and counter electrodes respectively. The working electrodes were fabricated by screen‐printing a water‐based carbon ink containing cobalt phthalocyanine for hydrogen peroxide detection. These were converted into a glucose microband biosensor by the addition of glucose oxidase into the carbon ink. In this paper, we discuss the fabrication and application of glucose microband electrodes for the determination of glucose in cell media. The dimensions (100–400 microns) of the microband electrodes result in radial diffusion, which results in steady state responses in the absence of stirring. The microband biosensors were investigated in cell media containing different concentrations of glucose using chronoamperometry. The device shows linearity for glucose determination in the range 0.5 mM to 2.5 mM in cell media. The screen‐printed microband biosensor design holds promise as a generic platform for future applications in cell toxicity studies.     

Determination of Lead(II) Using Screen‐Printed Bismuth‐Antimony Film Electrode

This work presents a disposable bismuth‐antimony film electrode fabricated on screen‐printed electrode (SPE) substrates for lead(II) determination. This bismuth‐antimony film screen‐printed electrode (Bi‐SbSPE) is simply prepared by simultaneously in situ depositing bismuth(III) and antimony(III) with analytes on the homemade SPE. The Bi‐SbSPE can provide an enhanced electrochemical stripping signal for lead(II) compared to bismuth film screen‐printed electrodes (BiSPE), antimony film screen‐printed electrodes (SbSPE) and bismuth‐antimony film glassy carbon electrodes (Bi‐SbGC). Under optimized conditions, the Bi‐SbSPE exhibits attractive linear responses towards lead(II) with a detection limit of 0.07 µg/L. The Bi‐SbSPE has been demonstrated successfully to detect lead in river water sample.     

Influence of Nafion Coatings and Surfactant on the Stripping Voltammetry of Heavy Metals at Bismuth‐Film Modified Carbon Film Electrodes

Nafion polymer coated bismuth‐film‐modified carbon film electrodes have been investigated for reducing the influence of contaminants such as surfactants in the anodic stripping voltammetry of trace metal ions. The influence of the coating on electrode response has been tested with both ex situ and in situ bismuth film deposition, with and without the polymer coating. The electrode assemblies and interfacial characteristics in the presence of the non‐ionic surfactant Triton‐X‐100 have been probed with electrochemical impedance spectroscopy. The Nafion coating successfully decreases the adsorption of Triton on the bismuth film surface, and demonstrates that this strategy allows measurement of these trace metals in environmental samples containing surfactants.     

Determination of Trace Lead and Cadmium in Water Samples by Anodic Stripping Voltammetry with a Nafion‐Ionic Liquid‐Coated Bismuth Film Electrode

A new chemically modified bismuth film electrode coated with an ionic liquid [(1‐ethyl‐3‐methylimidazolium tetracyanoborate (EMIM TCB)] and Nafion was developed for the simultaneous determination Pb²⁺ and Cd²⁺ by anodic stripping voltammetry. Compared with conventional bismuth film electrodes, this electrode exhibited greatly improved electrochemical activity for Pb²⁺ and Cd²⁺ detection due to the unique properties of Nafion polymer and ionic liquid. The key experimental parameters related to the fabrication of the electrode and the voltammetric measurements were optimized on the basis of the stripping signals, where the peak currents increased linearly with the metal concentrations in a range of 10–120 µg L^?1 with a detect limit of 0.2 µg L^?1 for Pb²⁺, and 0.5 µg L^?1 for Cd²⁺ for 120s deposition. High reproducibility was indicated from the relative standard deviations (1.9 and 2.5 %) for nine repetitive measurements of 20 µg L^?1 Pb²⁺ and Cd²⁺, respectively. In addition, the surface characteristics of the modified BiFE were investigated by scanning electron microscopy (SEM), and results showed that fibril‐like bismuth nanostructures were formed on the porous Nafion polymer matrix. Finally, the developed electrode was applied to determine Pb²⁺ and Cd²⁺ in water samples, indicating that this electrode was sensitive, reliable and effective for the simultaneous determination of Pb²⁺ and Cd²⁺.     

Ex Situ Scanning Electrochemical Microscopy (SECM) Investigation of Bismuth‐ and Bismuth/Lead Alloy Film‐Modified Gold Electrodes in Alkaline Medium

Scanning electrochemical microscopy (SECM) in feedback mode was employed to characterise the reactivity and microscopic peculiarities of bismuth and bismuth/lead alloys plated onto gold disk substrates in 0.1 mol L^?1 NaOH solutions. Methyl viologen was used as redox mediator, while a platinum microelectrode was employed as the SECM tip. The metal films were electrodeposited ex situ from NaOH solutions containing either bismuth ions only or both bismuth and lead ions. Approach curves and SECM images indicated that the metal films were conductive and locally reactive with oxygen to provide Bi³⁺ and Pb²⁺ ions. The occurrence of the latter chemical reactions was verified by local anodic stripping voltammetry (ASV) at the substrate solution interface by using a mercury‐coated platinum SECM tip. The latter types of measurements allowed also verifying that lead was not uniformly distributed onto the bismuth film electrode substrate. These findings were confirmed by scanning electron microscopy images. The surface heterogeneity produced during the metal deposition process, however, did not affect the analytical performance of the bismuth coated gold electrode in anodic stripping voltammetry for the determination of lead in alkaline media, even in aerated aqueous solutions. Under the latter conditions, stripping peak currents proportional to lead concentration with a satisfactory reproducibility (within 5 % RSD) were obtained.     

Voltammetric Behavior of Osmium‐Labeled DNA at Mercury Meniscus‐Modified Solid Amalgam Electrodes. Detecting DNA Hybridization

The complex of osmium tetroxide with 2,2′‐bipyridine has been utilized as a probe of DNA structure and an electroactive marker of DNA in DNA hybridization sensors. It produces several voltammetric signals, the most negative of them has been observed only at mercury electrodes. This signal is of catalytic nature affording a high sensitivity of DNA determination. The catalytic current due to evolution of hydrogen in voltammetry of DNA modified by complex of osmium tetroxide with 2,2′‐bipyridine (DNA‐Os,bipy) was studied. Solid amalgam electrodes (modified with mercury menisci) of silver (m‐AgSAE), copper (m‐CuSAE), gold, and of combined bismuth and silver, were used as possible substitutes for mercury electrodes. Besides the hanging mercury drop electrode (HMDE), the catalytic current was observed only on m‐AgSAE and m‐CuSAE. Electrodes of gold and bismuth amalgams did not give the catalytic current. The detection limit of DNA‐Os,bipy on HMDE was 0.1 ng mL^?1 (RSD=2.3 %, N=11), and on m‐AgSAE 0.2 ng mL^?1 (RSD=3.1%, N=11). The m‐AgSAE was successfully applied as a detection electrode in double‐surface DNA hybridization experiments offering highly specific discrimination between complementary (target) and nonspecific DNAs, as well as determination of the length of a repetitive DNA sequence. The m‐AgSAE has proved a convenient alternative to the HMDE or carbon electrodes used for similar purposes in previous work.     

Application of the Bismuth Film Electrode for Voltammetric Determination of Titanium Using Ti(IV)‐Oxalate‐Chlorate Catalytic System

The catalytic voltammetric protocol for the determination of titanium at a bismuth film electrode is presented. The method is based on the reduction of the Ti(IV)‐oxalate complex to Ti(III)‐oxalate in an acidic solution. It was proven that the addition of KClO₃ causes rapid oxidation of Ti(III)‐oxalate and, subsequently, an increase of the reduction peak current of Ti(IV) at the bismuth film electrode. Parameters that influence the Ti response, including the film preparation, solution pH, oxalate acid and chlorate concentrations, were optimized. The exploitation of the bismuth film electrode under the optimized conditions yielded a stable response for titanium, with high sensitivity (12.5 μA μM^?1), good precision (RSD=5.0%) and a low detection limit (1×10^?8 M).     

Differential Pulse Voltammetric Determination of 2‐Methyl‐4,6‐Dinitrophenol using Bismuth Bulk Electrode

This work reports the application of bismuth bulk electrode (BiBE) for the determination of 2‐methyl‐4,6‐dinitrophenol (MDNP) by differential pulse voltammetry (DPV) in Britton‐Robinson buffer of pH 12.0 as an optimal medium. BiBE was prepared by transferring molten bismuth into a glass tube under constant stream of nitrogen. The linear concentration dependences were measured from 1 to 10 μmol ? L^?1 and from 10 to 100 μmol ? L^?1 by using optimum accumulation potential of ?0.7 V and optimum accumulation time 30 s. Under these conditions limit of determination and limit of quantification was 0.45 and 1.5 μmol ? L^?1, respectively. The developed method was successfully applied for the analysis of tap water as a model sample.     

Voltammetric Determination of Neonicotinoid Pesticides at Disposable Screen‐Printed Sensors Featuring a Sputtered Bismuth Electrode

This work reports the determination of 5 neonicotinoid pesticides (Clothianidin, Imidacloprid, Thiamethoxam, Nitenpyram and Dinotefuran) in water samples by cathodic differential pulse (DP) voltammetry at screen‐printed disposable sensors featuring a sputtered bismuth thick‐film working electrode, a Ag reference electrode and a carbon counter electrode. The performance of the bismuth thick‐film electrodes was compared to that of a home‐made bismuth thin‐film electrode and a bismuth‐bulk electrode. The electrodes were further characterized by electrochemical and optical techniques. The effect of the pH of the supporting electrolyte on the DP reduction currents of the 5 pesticides was studied. The limits of quantification (LOQs) in 4 water matrices (distilled water, tap water, mineral water and surface water) were in the range 0.76 to 2.10 mg L^?1 but severe matrix effects were observed in the analysis of mineral and, especially, surface water samples. Using a solid‐phase extraction (SPE) procedure using Lichrolut EN cartridges and elution with methanol, the matrix effects were substantially reduced and the LOQs were in the range 9 to 17 µg L^?1_. The recoveries of surface water samples spiked with the 5 target neonicotinoids at two concentration levels (20 and 50 µg L^?1) were in the range 89 to 109 % and the % relative standard deviations ranged from 4.3 to 7.2 %.     

Bismuth Nanoparticles Incorporated Centri‐voltammetry for Phenol Detection

A novel approach has been developed for phenol detection by combining centri‐voltammetry with bismuth nanoparticles that are used as carrier reagent. The interaction between bismuth and phenol and also the application of centrifugation provide the effective deposition of phenol onto the electrode surface. Direct voltammetric scan without applying any filtration or decantation prevents the analyte loss. As a result, very sensitive results were obtained with linear ranges of 2–75 μM and 100–500 μM and LOD values of 40 nM and 395 nM, respectively. Developed system was also applied for phenol detection in river sample and recovery value was calculated as 115 %.     

Mass Transport at Microband Electrodes: Transient,Quasi‐Steady‐State,and Convective Regimes

Mass transport at microband electrodes is investigated theoretically and experimentally in unstirred solutions by chronoamperometry and cyclic voltammetry. Because natural convection limits the convection‐free domain up to which diffusion layers may only expand, several regimes of mass transport are identified through simulation by means of a previous model. A zone diagram is established which allows all relative contributions to mass transport to be delineated according to the electrode dimension, timescale of experiment, and amplitude of natural convection. In opposition to the quasi‐steady‐state regime usually expected at microband electrodes under diffusion control, a steady‐state regime always occurs at long enough times. By comparison to microdisk electrodes, a greater influence of natural convection is predicted. These results are validated experimentally by monitoring current responses and mapping steady‐state concentration profiles at microband electrodes.     

Differential Pulse Voltammetric Determination of Paraquat Using a Bismuth‐Film Electrode

A bismuth‐film electrode (BiFE) ex situ electrochemically deposited onto a copper substrate has been presented for paraquat determination. The bismuth film was electrochemically deposited at an applied potential of ?0.18 V vs. Ag/AgCl (3.0 M KCl) for 200 s. The analytical curve was linear in the paraquat concentration range from 6.6×10^?7 M to 4.8×10^?5 M with a limit of detection of 9.3×10^?8 M. The method presented satisfactory results at a confidence level of 95% and the performance was evaluated in water samples.     

A Novel Cell Design for the Improved Stripping Voltammetric Detection of Zn(II), Cd(II), and Pb(II) on Commercial Screen‐Printed Strips by Bismuth Codeposition in Stirred Solutions

A novel electrochemical cell design is proposed to allow fast, reproducible and highly efficient convective transport of dissolved substances to screen‐printed electrochemical three‐electrode strips mounted on miniaturized plastic vessels, with the goal of improving detection limits in disposable electrochemical stripping field sensors. The experimental configuration has been tested for accumulation of the selected heavy metals ions Zn(II), Cd(II), and Pb(II), codeposited with bismuth ions on a carbon disk screen‐printed working electrode before detection by square wave anodic stripping voltammetry. Chemical and instrumental variables of the proposed device and associate electrochemical method were optimized. Selected parameters gave detection limits in the low ng mL^?1 range with moderate deposition time (120 s). Practical applicability was tested on certified water and real samples (tap water and waste water), with acceptable results, suggesting potential usefulness for field environmental monitoring of heavy metals.     

The Use of the Bismuth Film Electrode for the Anodic Stripping Voltammetric Determination of Tin

Bismuth coated glassy carbon electrodes have been applied to the square‐wave anodic stripping voltammetry (SWASV) of trace concentrations of tin. Optimization of Bismuth Film Electrode (BFE) performance was conducted after initial comparison with the more traditional mercury electrode. Simultaneous deposition of tin and bismuth at ?1.3 V for 2 minutes in a supporting electrolyte of 2.5 M sodium bromide utilizing a square‐wave stripping step, allowed analysis of tin at the μg L^?1 level. Parameters, such as deposition potential and time, bismuth concentration, square‐waveform settings including amplitude, step height and frequency were studied and optimized. The dependence of stripping current on deposition time indicates that using longer deposition time should facilitate sub μg L^?1 analysis. Tin was analyzed simultaneously with cadmium and either indium or thallium; Where as lead and copper were not resolved from the stripping peaks of tin and bismuth respectively. Finally, the method was applied to the analysis of tin in fruit juice.     

Differential Pulse Anodic Stripping Voltammetric Determination of Bismuth(III) with 1‐(2‐Pyridylazo)‐2‐naphthol and Ionic Liquid Modified Carbon Paste Electrode

In this paper 1‐(2‐pyridylazo)‐2‐naphthol (PAN) and ionic liquid 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) were mixed with graphite powder to get a modified carbon paste electrode (PAN‐IL‐CPE), which was further used for the sensitive determination of bismuth(III). By the co‐contribution of the formation of PAN‐Bi complex and the accumulation effect of IL, more bismuth(III) was electrodeposited on the surface of the PAN‐IL‐CPE. Then the reduced Bi was oxidized and detected by differential pulse anodic stripping voltammetry (DPASV) with the oxidation peak appeared at 0.17 V (vs. SCE). Under the optimal conditions the oxidation peak current was proportional to the bismuth(III) concentration in the range from 0.04 to 7.5 μmol L^?1 with the detection limit as 3.9 nmol L^?1. The proposed method was successfully applied to the stomach medicine sample detection with good recovery.     

Preparation of Nano‐bismuth with Different Particle Sizes and the Size Dependent Electrochemical Thermodynamics

Nano‐bismuth has excellent electrochemical properties. However, it is still unclear how the particle size of nano‐bismuth influences its electrochemical thermodynamic properties. In this paper, spherical bismuth nanoparticles with different particle sizes were prepared by solvothermal method; the electrode potentials, the temperature coefficients of the electrode potentials and the thermodynamic functions of reaction for nano‐bismuth electrodes with different particle sizes at different temperatures were determined; and the effects of particle size on the electrode potential, the temperature coefficient and the thermodynamic functions were discussed. The experimental results show that particle size of bismuth nanoparticles has a significant influences on the electrochemical thermodynamic properties. The standard electrode potential of the nano‐bismuth electrode with a diameter of 39.9 nm was 0.009 V lower than that of the ordinary standard electrode (0.308 V); the temperature coefficient of the electrode potential with a diameter of 39.9 nm was nearly double that of 85.9 nm. With the particle sizes decrease, the standard molar Gibbs energy of reaction, the standard molar enthalpy of reaction, the standard molar entropy of reaction, the molar reversible reaction heat and the temperature coefficient increase; and these quantities are linearly related to the reciprocal of the particle diameter.     

Enhanced Resolution of Copper and Bismuth by Addition of Gallium in Anodic Stripping Voltammetry with the Bismuth Film Electrode

This paper presents the enhanced analysis of copper on a bismuth electrode upon addition of gallium(III). The presence of gallium alleviates the problems of overlapping stripping signals usually observed between copper and bismuth when using the Bismuth Film Electrode. In addition, it has been found that the presence of gallium improves the reproducibility of the bismuth stripping signal. Simultaneous deposition of copper and bismuth at ?1500 mV for 2 minutes in a supporting electrolyte composed of 0.1 M pH 4.75 acetate buffer with 250 μg L^?1 gallium yields well resolved copper and bismuth signals when analyzed with square‐wave anodic stripping voltammetry. Simultaneous analysis of copper and lead yielded linear calibration plots in the range 10 to 100 μg L^?1 with regression coefficients of 0.997 and 0.994 respectively. The theoretical detection limit for copper was calculated to be 4.98 μg L^?1 utilizing a 2 minutes deposition time. The relative standard deviation for a copper concentration of 50 μg L^?1 was 1.6% (n=10).     

Carbon Nanotubes‐Based Amperometric Cholesterol Biosensor Fabricated Through Layer‐by‐Layer Technique

A carbon nanotubes‐based amperometric cholesterol biosensor has been fabricated through layer‐by‐layer (LBL) deposition of a cationic polyelectrolyte (PDDA, poly(diallyldimethylammonium chloride)) and cholesterol oxidase (ChOx) on multi‐walled carbon nanotubes (MWNTs)‐modified gold electrode, followed by electrochemical generation of a nonconducting poly(o‐phenylenediamine) (PPD) film as the protective coating. Electrochemical impedance measurements have shown that PDDA/ChOx multilayer film could be formed uniformly on MWNTs‐modified gold electrode. Due to the strong electrocatalytic properties of MWNTs toward H₂O₂ and the low permeability of PPD film for electroacitve species, such as ascorbic acid, uric acid and acetaminophen, the biosensor has shown high sensitivity and good anti‐interferent ability in the detection of cholesterol. The effect of the pH value of the detection solution on the response of the biosensor was also investigated. A linear range up to 6.0 mM has been observed for the biosensor with a detection limit of 0.2 mM. The apparent Michaelis‐Menten constant and the maximum response current density were calculated to be 7.17 mM and 7.32 μA cm^?2, respectively.     

Back‐to‐Back Screen‐Printed Electroanalytical Sensors: Extending the Potential Applications of the Simplistic Design

In our previous paper (Analyst, 2014 , 139, 5339) we introduced the concept of the back‐to‐back electrochemical design where the commonly overlooked back of screen‐printed electrodes are utilised to provide electroanalytical enhancements in screen‐printed electroanalytical sensors. In this configuration the overall sensor comprises of a flexible polyester substrate which has a total of two working, counter and reference electrodes present on the sensor, with a set of electrodes on each side of the substrate. The sensors are designed to allow for a commonly shared electrical connection to the potentiostat and do not require any specialised connections. In this paper we demonstrate proof‐of‐concept extending the electroanalytical utility of the back‐to‐back screen‐printed electrode sensors to bulk modified single‐walled carbon‐nanotubes and electrocatalytic cobalt phthalocyanine microband electrodes. The electroanalytical applications of these novel electrode configuration are exemplified towards the sensing of dopamine, capsaicin and hydrazine. This paper demonstrates the versatility of the back‐to‐back configuration where different surface modifications can be readily employed giving rise to enhancements in sensor performance.     

Lab‐on‐a‐Chip Sensor with Evaporated Bismuth Film Electrode for Anodic Stripping Voltammetry of Zinc

In this work, we report on the development of a lab‐on‐a‐chip electrochemical sensor that uses an evaporated bismuth electrode to detect zinc using square wave anodic stripping voltammetry. The microscale electrochemical cell consists of a bismuth working electrode, an integrated silver/silver chloride reference electrode, and a gold auxiliary electrode. The sensor exhibits a linear response in 0.1 M acetate buffer at pH 6 with zinc concentrations in the 1–30 μM range and a calculated detection limit of 60 nM. The sensor successfully detected zinc in a bovine serum extract and the results were corfirmed by independent AAS measurements. Our results demonstrate the advantageous qualities of this lab‐on‐a‐chip electrochemical sensor for clinical applications, which include small sample volume (µL scale), reduced cost, short response time and high accuracy at low concentrations of analyte.