Analysis of oxidized multi-walled carbon nanotubes in single K562 cells by capillary electrophoresis with laser-induced fluorescence

Short oxidized multi-walled carbon nanotubes (CNT) were derivatized with fluorescein isothiocyanate (FITC). Capillary electrophoresis coupled with laser-induced fluorescence (CE–LIF) was then used to separate and detect the fluorescently labeled carbon-nanotube probes (CNTP) in multidrug-resistant cells (K562A) and the parent cells (K562S). Greater expression of P-glycoprotein in K562A cells than in K562S cells was confirmed by use of anti-P-glycoprotein antibody and flow-cytometric analysis. Analyses of CNTP in both cell lines using both CE–LIF and flow cytometry showed that CNTP could traverse the cellular membrane without being pumped out by P-glycoprotein. The CNTP distributed in both cell lines was analyzed at the single cell level and the results were compared with those from analysis of ten cells and of the lysate from bulk cells. The results revealed the CE–LIF method could be used for quantitative analysis of CNT in single cells in studies of drug delivery and multidrug resistance.      

Capillary electrophoresis of covalently functionalized single‐chirality carbon nanotubes

We demonstrate the separation of chirality‐enriched single‐walled carbon nanotubes (SWCNTs) by degree of surface functionalization using high‐performance CE. Controlled amounts of negatively charged and positively charged functional groups were attached to the sidewall of chirality‐enriched SWCNTs through covalent functionalization using 4‐carboxybenzenediazonium tetrafluoroborate or 4‐diazo‐N,N‐diethylaniline tetrafluoroborate, respectively. Surfactant‐ and pH‐dependent studies confirmed that under conditions that minimized ionic screening effects, separation of these functionalized SWCNTs was strongly dependent on the surface charge density introduced through covalent surface chemistry. For both heterogeneous mixtures and single‐chirality‐enriched samples, covalently functionalized SWCNTs showed substantially increased peak width in electropherogram spectra compared to nonfunctionalized SWCNTs, which can be attributed to a distribution of surface charges along the functionalized nanotubes. Successful separation of functionalized single‐chirality SWCNTs by functional density was confirmed with UV‐Vis‐NIR absorption and Raman scattering spectroscopies of fraction collected samples. These results suggest a high degree of structural heterogeneity in covalently functionalized SWCNTs, even for chirality‐enriched samples, and show the feasibility of applying CE for high‐performance separation of nanomaterials based on differences in surface functional density.     

Dual‐opposite multi‐walled carbon nanotube modified carbon fiber microelectrode for microfluidic chip‐capillary electrophoresis determination of methyl parathion metabolites in human urine

Methyl parathion (MP) is a highly toxic organophosphate and its exposure may lead to substantial adverse effects to human health. The existence of 4‐nitrophenol (4‐NP) in the form of free phenol, glucuronide (4‐NP‐G) or as a sulfate ester (4‐NP‐S) can be used as biomarkers to assess the duration and extent of MP exposure. In this work, a MC‐CE device incorporating post‐CE amperometric detection using multi‐walled carbon nanotubes (MWNTs) modified carbon fiber microelectrode (CFME) was fabricated and assessed for simultaneous determination of 4‐NP, 4‐NP‐G, and 4‐NP‐S in human urine. The detection sensitivity and stability was greatly enhanced by the modification of MWNTs. The capability of the MC‐CE device with dual MWNTs modified CFME for detecting impurity was assessed and reliability established by high recoveries from 95 to 97% for spiked MP biomarkers. The method developed is shown to provide a simple, sensitive, and reliable means for monitoring 4‐NP, 4‐NP‐G, and 4‐NP‐S in human urine.     

Improved sample preparation method for glycan analysis of glycoproteins by CE‐LIF and CE‐MS

CE is a high‐resolution separation technique broadly used in the biotechnology industry for carbohydrate analysis. The standard sample preparation protocol for CE analysis of glycans released from glycoproteins generally requires derivatization times of overnight at 37°C, using ≥100 fold excess of fluorophore reagent, 8‐aminopyrene‐1,3,6‐trisulfonic‐acid, if the sample is unknown, or it is a regulated biotherapeutic product, possibly containing terminal sialic acid(s). In this paper, we report on significant improvements for the standard CE sample preparation method of glycan analysis. By replacing the conventionally used acetic acid catalyst with citric acid, as low as 1:10 glycan to fluorophore molar ratio (versus the typical 1:≥100 ratio) maintained the >95% derivatization yield at 55°C with only 50 min reaction time. Terminal sialic acid loss was negligible at 55°C during the derivatization process, and indicating that the kinetics of labeling at 55°C was faster than the loss of sialic acid from the glycan. The reduced relative level of 8‐aminopyrene‐1,3,6‐trisulfonic‐acid simplified the removal of excess reagent, important in both CE‐LIF (electrokinetic injection bias) and CE‐MS (ion suppression). Coupling CE‐ ESI‐MS confirmed that the individual peaks separated by CE corresponded to single glycans and increased the confidence of structural assignment based on glucose unit values.     

Determination of the stereoisomers in aqueous medium and serum and validation studies of racemic aminoalkanol derivatives of 1,7‐dimethyl‐8,9‐diphenyl‐4‐azatricyclo[5.2.1.02,6]dec‐8‐ene‐3,5,10‐trione,potential new anticancer drugs,by capillary electrophoresis

A new method for the determination of the stereoisomers, in aqueous medium and serum, of the racemic aminoalkanol derivatives I and II of 1,7‐dimethyl‐8,9‐diphenyl‐4‐azatricyclo[5.2.1.0^2,6]dec‐8‐ene‐3,5,10‐trione, which were found in earlier studies to be potential anticancer drugs, was developed and validated. The optimized conditions included 25 mM phosphate buffer adjusted to pH 2.5, containing γ‐cyclodextrin at a concentration of 5% m/v, as background electrolyte, an applied voltage of +10 kV, and a temperature of 25°C. Separations were carried out using a fused‐silica capillary. The developed method of determining the enantiomers of compounds I(S), I(R) and II(S), II(R) was characterized by the following parameters: a detection time within 10.8 min, a detection limit in the range of 141.2–141.7 ng/mL using the UV absorption detection at 200 nm. Good linearity (R² = 0.9989–0.9998) was achieved within the range of concentrations studied. A very good extraction yield of 95.4–99.7% was achieved, and recoveries were carried out from both aqueous solutions and matrix serum. The repeatability of the method for peak areas with an accuracy of the determined concentrations of the analytes in the range of 1.43–1.89%, and limits of quantitation in the range of 432.4–436.3 ng/mL were achieved.     

A simple and fast method for chlorsulfuron and metsulfuron methyl determination in water samples using multiwalled carbon nanotubes (MWCNTs) and capillary electrophoresis

A new method to determine metsulfuron methyl (MSM) and chlorsulfuron (CS) in different water samples was developed. It consists in a solid phase extraction (SPE) procedure using multiwalled carbon nanotubes (MWCNTs) as sorbent material in combination with capillary zone electrophoretic determination. To carry out the pre-concentration step, a simple flow injection system was developed and optimized. Thus, 250 μL of aqueous solution containing methanol 50% (v/v) and acetonitrile 2% (v/v) as eluent, 10 mL of sample and a flow rate of 1.15 mL min⁻¹ were selected. The CE variables also were optimized. A rapid determination and good resolution of two herbicides were obtained within 9 min using a simple electrophoretic buffer (50 mmol L⁻¹ sodium tetraborate with 3% of methanol, pH = 9.0). Under the optimum conditions, the calibration curves were linear between 0.5 and 6 μg L⁻¹ for MSM and CS with R² = 0.995 and 0.997, respectively. The repeatability of the proposed method, expressed as relative standard deviation (RSD), varied between 4.1% and 5.4% (n = 10) and the detection limits for MSM and CS were 0.40 and 0.36 μg L⁻¹, respectively. Good results were achieved when the proposed method was applied to spiked real water samples. The recoveries percentages of the two analytes were over the range 86-108%.     

Analytical applications of glassy carbon electrodes modified with multi-wall carbon nanotubes dispersed in polyethylenimine as detectors in flow systems

This work reports the advantages of using glassy carbon electrodes (GCEs) modified with multi-wall carbon nanotubes (CNT) dispersed in polyethylenimine (PEI) as detectors in flow injection and capillary electrophoresis. The presence of the dispersion of CNT in PEI at the electrode surface allows the highly sensitive and reproducible determination of hydrogen peroxide, different neurotransmitters (dopamine (D) and its metabolite dopac, epinephrine (E), norepinephrine (NE)), phenolic compounds (phenol (P), 3-chlorophenol (3-CP) and 2,3-dichlorophenol (2,3CP)) and herbicides (amitrol). Sensitivities enhancements of 150 and 140 folds compared to GCE were observed for hydrogen peroxide and amitrol, respectively. One of the most remarkable properties of the resulting electrode is the antifouling effect of the CNT/PEI layer. No passivation was observed either for successive additions (30) or continuous flow (for 30 min) of the compounds under investigation, even dopac or phenol. A critical comparison of the amperometric and voltammetric signal of these different analytes at bare- and PEI-modified glassy carbon electrodes and pyrolytic graphite electrodes is also included, demonstrating that the superior performance of CNT is mainly due to their unique electrochemical properties. Glassy carbon electrodes modified with CNT-PEI dispersion also show an excellent performance as amperometric detector in the electrophoretic separation of phenolic compounds and neurotransmitters making possible highly sensitive and reproducible determinations.     

碳纳米管与CTMAB协同加强荧光探针并应用于测定痕量锰

提出将碳纳米管(CNT)作为一种新型分析增效试剂用于加强荧光探针,研究了其与阳离子表面活性剂-十六烷基溴化铵(CTMAB)的协同增敏机理,并应用于苯基荧光酮(PF)荧光猝灭法测定锰离子的体系中。结果表明,在CNT与CTMAB复配的影响下,PF与Mn2+形成的络合物荧光猝灭强度最大,据此建立了CNT加强荧光猝灭法测定痕量锰的新方法。方法的检出限为0.2μg/L,线性范围为0.4~10μg/L,回归方程:ΔF=10.48ρ(μg/L)+10.77,R=0.9992。本法可用于自来水中Mn2+含量的检测。     

Determination of formaldehyde in single cell by capillary electrophoresis with LIF detection

As a small molecule gas, formaldehyde (FA) is the simplest carbonyl active material and plays an important role in the carbon cycle of metabolism. However, due to the volatile nature of the gas, it is difficult to accurately quantify its content, which limits the study of the mechanism of action in life activities. Thus, an efficient approach to quantitative detection of FA in cells especially in single cell is urgent needed. Nevertheless, no method for quantifying FA in single cell has been reported to date. In this work, a fluorescent probe N‐propyl‐4‐hydrazino‐naphthalimide (NPHNA), which has highly desirable attributes and has been applied to living biological samples, was chosen as labeling reagent to detect endogenous FA at single cell level. After optimization of separation conditions, fast baseline separation of the FA derivative N‐propyl‐4‐hydrazone‐naphthalimide product (NPHNA‐FA) and NPHNA was achieved in about 5 min by CE with LIF detection. The detection limit for FA was 5 amol (S/N ratio of 3). The developed method was validated by the measurements of intracellular levels of FA in single cell.     

Enhanced separation of purine and pyrimidine bases using carboxylic multiwalled carbon nanotubes as additive in capillary zone electrophoresis

This paper describes the enhanced separation of adenine (A), hypoxanthine (HX), 8-azaadenine (8-AA), thymine (T), cytosine (C), uracil (U) and guanine (G) by CZE dispersing carboxylic multiwalled carbon nanotubes (c-MWNTs) into the running buffer. The effect of important factors such as c-MWNT nanoparticle concentration, the acidity and concentration of running buffer, and separation voltage were investigated to acquire the optimum conditions. The seven purine and pyrimidine bases could be well separated within 16 min in a 35 cm effective length fused-silica capillary at a separation voltage of +8.0 kV in a 23 mM tetraborate buffer (pH 9.2) containing 8.0 x 10(-5) g/mL c-MWNTs. Under the optimal conditions, the linear ranges were of 2-250 microg/mL for A (R2 = 0.995), 3-200 microg/mL for U (R2 = 0.990) and G (R2 = 0.992), 3-250 microg/mL for T (R2 = 0.998), 2-200 microg/mL for C (R2 = 0.985) and 4-200 microg/mL for HX (R2 = 0.988) and 8-AA (R2 = 0.990). The detection limits were 0.9 microg/mL for A (S/N = 3), 2.4 microg/mL for U, 2.0 microg/mL for T, 1.5 microg/mL for C, 2.5 microg/mL for G and 3.0 microg/mL for HX and 8-AA. The proposed method was successfully applied for determining five purine and pyrimidine bases in yeast RNA.     

原子力显微镜对中性粒细胞与K562细胞超微结构及机械性能的探测

采用原子力显微镜在纳米尺度下对正常中性粒细胞与白血病细胞株K562细胞的表面形貌及细胞的硬度、粘附力进行定性定量分析.结果表明,相比正常中性粒细胞的平均粗糙度(Ra=5.31±1.52 nm),K562细胞的超微结构更为复杂,细胞表面平均粗糙度显著升高(Ra=26.54±8.01 nm).此外,细胞的生物机械特性也有显著差别:中性粒细胞的硬度为9.5±1.3 kPa,AFM针尖与中性粒细胞的非特异性粘附力为135±23.4 pN;K562细胞的硬度为3.0±0.8 kPa,AFM针尖与K562细胞的非特异性粘附力为95±15.6 pN.AFM在单细胞水平上的探测表明,中性粒细胞和K562细胞的超微结构和机械特性均有明显差异.通过对细胞表面超微结构和力学特性的探测可以诊断慢性粒细胞白血病,原子力显微镜有望成为临床肿瘤诊断的工具.     

纳升电喷雾毛细管液相色谱-串联质谱鉴定K562细胞株中混合蛋白质

用标准蛋白质混合物建立了一种适用于低丰度混合蛋白质及其异构体分离与鉴定的蛋白质组学方法。通过IPG胶条等电聚焦分离蛋白质,染色后进行混合胶内酶切,采用纳升电喷雾毛细管液相色谱一串联质谱“散弹法（shot-gun）”分析酶切产物,并进行数据库检索鉴定蛋白质。运用该方法从K562细胞株样品中鉴定出14种具有重要功能的蛋白质,部分蛋白质同时在多个条带中出现,可能是异构体。肽段及其碎片离子的平均质量偏差小于0．05U,综合得分大都远远超过有效值。该方法灵敏、准确度高、分辨率高、省时、便于操椎存苍宗罾白甩异构体青而右优势．     

Capillary electrophoresis coupled to chemometrics for analysis of carbon dots in nanoparticles mixtures

Since their discovery in 2004, carbon dots (CDs) have attracted attention due to their intrinsic physicochemical properties and the easy synthesis from simple precursors. However, quantification of CDs in mixtures of nanoparticles with similar sizes and surface functionality is still a challenging issue for research applications or regulatory purposes. In this work, CDs and silver nanoparticles were first synthesized under alkaline conditions by using glucose as precursor and capping agent, respectively. Mixtures of these nanoparticles were made at micromolar range, without purification, and then analyzed by CE–DAD, using an electrolyte solution composed of 20 mM sodium borate and 20 mM SDS at pH 8.5, in a total time of <15 min. The three-way electrophoretic data were then decomposed by advanced chemometric models, parallel factor analysis and multivariate curve resolution–alternating least-squares. The explained variances for both models were 95.8% (parallel factor analysis) and 85.3% (multivariate curve resolution–alternating least-squares). In both cases, the quality of the results was verified by the root mean square standard deviation coefficient variation, which resulted lower than 5%, and no significant bias was observed at 95% of statistical confidence. Satisfactory prediction for CDs concentration was obtained with recovery values between 80.0% and 115%.     

Development and application of carbon nanotubes assisted electromembrane extraction (CNTs/EME) for the determination of buprenorphine as a model of basic drugs from urine samples

In this work carbon nanotubes assisted electromembrane extraction (CNTs/EME) coupled with capillary electrophoresis (CE) and ultraviolet (UV) detection was developed for the determination of buprenorphine as a model of basic drugs from urine samples. Carbon nanotubes reinforced hollow fiber was used in this research. Here the CNTs serve as a sorbent and provide an additional pathway for solute transport. The presence of CNTs in the hollow fiber wall increased the effective surface area and the overall partition coefficient on the membrane; and lead to an enhancement in the analyte transport. For investigating the influence of the presence of CNTs in the SLM on the extraction efficiency, a comparative study was carried out between EME and CNTs/EME methods. Optimization of the variables affecting these methods was carried out in order to achieve the best extraction efficiency. Optimal extractions were accomplished with NPOE as the SLM, with 200 V as the driving force, and with pH 2.0 in the donor and pH 1.0 in the acceptor solutions with the whole assembly agitated at 750 rpm after 25 min and 15 min for EME and CNTs/EME, respectively.     

Sensitive determination of sulfonamides in environmental water by capillary electrophoresis coupled with both silvering detection window and in‐capillary optical fiber light‐emitting diode‐induced fluorescence detector

A new detector, silvering detection window and in‐capillary optical fiber light‐emitting diode‐induced fluorescence detector (SDW‐ICOF‐LED‐IFD), is introduced for capillary electrophoresis (CE). The strategy of the work was that half surface of the detection window was coated with silver mirror, which could reflect the undetected fluorescence to the photomultiplier tube to be detected, consequently enhancing the detection sensitivity. Sulfonamides (SAs) are important antibiotics that achieved great applications in many fields. However, they pose a serious threat on the environment and human health when they enter into the environment. The SDW‐ICOF‐LED‐IFD‐CE system was used to determine fluorescein isothiocyanate (FITC)‐labeled sulfadoxine (SDM), sulfaguanidine (SGD) and sulfamonomethoxine sodium (SMM‐Na) in environmental water. The detection results obtained by the SDW‐ICOF‐LED‐IFD‐CE system were compared to those acquired by the CE with in‐capillary optical fiber light‐emitting diode‐induced fluorescence detection (ICOF‐LED‐IFD‐CE). The limits of detection (LODs) of SDW‐ICOF‐LED‐IFD‐CE and ICOF‐LED‐IFD‐CE were 1.0–2.0 nM and 2.5–7.7 nM (S/N = 3), respectively. The intraday (n = 6) and interday (n = 6) precision of migration time and corresponding peak area for both types of CE were all less than 0.86% and 3.68%, respectively. The accuracy of the proposed method was judged by employing standard addition method, and recoveries obtained were in the range of 92.5–102.9%. The results indicated that the sensitivity of the SDW‐ICOF‐LED‐IFD‐CE system was improved, and that its reproducibility and accuracy were satisfactory. It was successfully applied to analyze SAs in environmental water.     

The sensitive capillary electrophoretic‐LIF method for simultaneous determination of curcuminoids in turmeric by enhancing fluorescence intensities of molecules upon inclusion into (2‐hydroxypropyl)‐β‐cyclodextrin

Curcuminoids have received great attention in the past decades due to their health benefit properties. The aim of this study is to develop a very simple, rapid, and sensitive capillary zone electrophoresis technique coupled with a laser induced fluorescence detector (LIF) for the simultaneous determination of three major curcuminoids of turmeric, namely, curcumin, demethoxy curcumin (DMC), and bisdemethoxy curcumin (BDMC). Background electrolyte was selected as borate at pH 9.6 and (2‐hydroxypropyl)‐β‐cyclodextrin (2‐HP‐β‐CD) was added to prevent rapid alkali degradation of curcuminoids in buffer and to increase fluorescence intensities of molecules. With the addition of 2‐HP‐β‐CD to the separation electrolyte, the fluorescence signal intensities of curcuminoids were enhanced considerably by 30, 40, and 54 fold for curcumin, DMC, and BDMC, respectively. The three curcuminoids of turmeric were fully separated and quantified in less than 4.5 min. The repeatability of the peak areas of curcuminoids for intra‐day and inter‐day experiments was in the satisfactory range of 2.26 and 2.55%, respectively. The LOD and LOQ values for the developed method were equal to or less than 0.081 and 0.270 μg/mL, respectively, for all curcuminoids. The developed method was successfully applied to find curcuminoids amount in turmeric samples and herbal supplements.     

Azide-functionalization of carbon nanotubes by electrochemical oxidation of N3- in situ

Azide-functionalization of single-walled carbon nanotubes （SWCNTs） was achieved by electrochemical oxidation of N3 in situ. The functionalized nanotubes were characterized in details by single internal reflection infrared spectroscopy （ATR-FTIR） and thermogravimetic analysis （TGA/MS）. The results revealed that a covalent C-N bond had formed and this might provide an effective method for the preparation of azide-functionalized materials, especially carbon materials. The degree of functionaliza- tion was measured by X-ray photoelectron spectroscopy （XPS）.     

Significant improvements in mechanical property and water stability of chitosan by carbon nanotubes

In this work, high storage modulus and high water stability of chitosan was prepared by incorporating chitosan-grafted carbon nanotubes (CNTs-g-CS). This dramatically improved mechanical property and water stability of chitosan would broaden its biochemical and electrochemical applications. The methodology adopted here by incorporating the CNTs-g-CS allowed a high amount of CNTs incorporation in chitosan without phase separations and enabled the preparations of a durable chitosan/CNTs nanocomposite-modified electrode for biosensor uses. The CNTs-g-CS was synthesized by grafting chitosan onto the carboxylated CNTs in acetic acid-added aqueous solution at 98 °C for 24 h. Thermal gravimetric analysis showed that the content of the chitosan grafts on the CNTs was about 25 wt% of the synthesized CNTs-g-CS. As compared with the ungrafted CNTs, the CNTs-g-CS exhibited a significantly improved dispersion in the chitosan matrix, as examined by optical microscopy and scanning electron microscopy, resulting in significantly improved storage modulus and water stability of the chitosan nanocomposites as revealed by dynamic mechanical analysis and water treatments data, respectively. The storage modulus was significantly up by 134% from 6.4 GPa for the pure chitosan to 15 GPa for the chitosan nanocomposite containing 40 wt% CNTs-g-CS. The water stability of the chitosan nanocomposite films was significantly up from less than 12 h for the chitosan containing various amounts of ungrafted CNTs to at least 48 h for the chitosan containing 20, 30, and 40 wt% CNTs-g-CS.     

Magnetic solid‐phase extraction of polycyclic aromatic hydrocarbons in water samples by Fe3O4@polypyrrole/carbon nanotubes

A magnetic solid‐phase extraction method coupled with gas chromatography was proposed for the determination of polycyclic aromatic hydrocarbons in the environmental water samples. The magnetic adsorbent was prepared by incorporating Fe₃O₄ nanoparticles, multi‐walled carbon nanotubes, and polypyrrole. The main factors affecting the extraction efficiency including the amount of the sorbents, desorption conditions, extraction time, salt concentration, and sample solution pH were investigated and optimized. Under the optimum conditions, good linearity was obtained within the range of 0.03?100 ng/mL for all analytes, with correlation coefficients ranging from 0.9942 to 0.9973. The method detection limits (S/N = 3) were in the range of 0.01–0.04 ng/mL and the limits of quantification (S/N = 10) were 0.03–0.1 ng/mL. Repeatability of the method was assessed through five consecutive extractions of independently prepared solutions at concentrations of 0.1, 10, and 100 ng/mL of the compounds. The observed repeatability ranged 3.4–10.9% depending of the compound considered. The proposed method was successfully applied in the analysis of PAHs in environmental samples (tap, well, river, and wastewater). The recoveries of the method ranged between 93.4 and 99.0%. The procedure proved to be efficient and environmentally friendly.