Effect of Pulse Width of Square Potential to Remove Silver Interference in the Determination of Mercury(II)

A graphite electrode modified with silver (Ag‐CPE) has been applied to detect mercury(II) using differential pulse voltammetry (DPV). Under optimized conditions, the calibration curve is linear in the range from 5.0×10^?8 mol L^?1 to 1.0×10^?4 mol L^?1 of mercury(II). The detection limit was found to be 3.38×10^?8 mol L^?1 with a relative standard deviation (RSD) of 2.25 % (n=8). The proposed method was successfully applied for the detection of mercury(II) in leachate samples. The Ag‐CP composites were characterized using X‐ray diffraction (XRD), BET adsorption analysis and scanning electron microscopy (SEM).     

Anodic Stripping Voltammetry Determination of Pb(II) and Cd(II) at a Bismuth/Poly(aniline) Film Electrode

Abstract

A novel voltammetric method—anodic—using a bismuth/poly(aniline) film electrode has been developed for simultaneous measurement of Pb(II) and Cd(II) at low µg L^?1 concentration levels by stripping voltammetry. The results confirmed that the bismuth/poly(aniline) film electrode offered high‐quality stripping performance compared with the bismuth film electrode. Well‐defined sharp stripping peaks were observed for Pb(II) and Cd(II), along with an extremely low baseline. The detection limits of Pb(II) and Cd(II) are 1.03 µg L^?1 and 1.48 µg L^?1, respectively. The bismuth/poly (aniline) electrode has been applied to the determination of Pb(II) in tap water samples with satisfactory results.     

Determination of lead(II) in aqueous solution using carbon nanotubes paste electrodes modified with Amberlite IR-120

A new composite electrode is described for anodic stripping voltammetry determination of Pb(II) at trace level in aqueous solution. The electrode is based on the use of multiwalled carbon nanotubes and Amberlite IR-120. The anodic stripping voltammograms depend, to a large extent, on the composition of the modified electrode and the preconcentration conditions. Under optimum conditions, the anodic peak current at around ?0.57 V is linearly related to the concentration of Pb(II) in the range from 9.6?×?10^?8 to 1.7?×?10^?6 mol L^?1 (R?=?0.998). The detection limit is 2.1?×?10^?8 mol L^?1, and the relative standard deviation (RSD) at 0.24?×?10^?6 mol L^?1 is 1.7% (n?=?6). The modified electrode was applied to the determination of Pb(II) using the standard addition method; the results showed average relative recoveries of 95% for the samples analysed.

Voltammetric Determination of Acibenzolar‐S‐Methyl Using a Renewable Silver Amalgam Film Electrode

Acibenzolar‐S‐methyl (ASM) is a novel fungicide applied for crop protection. A renewable silver amalgam film electrode was used for the determination of ASM in pH 3.4 Britton? Robinson buffer using square wave adsorptive stripping voltammetry (SW AdSV). The parameters of the method were optimized. The electroanalytical procedure made possible to determine ASM in the concentration range of 5×10^?8–3×10^?7 mol L^?1 (LOD=4.86×10^?9, LOQ=1.62×10^?8 mol L^?1). The effect of common interfering pesticides and heavy metal ions was checked. The validated method was applied in ASM determination in spiked water samples.     

Palladium Particles‐Impregnated Natural Phosphate Electrodes for Electrochemical Determination of Mercury in Ambient Water Samples

We present here a simple procedure for the determination of mercury(II) using differential pulse anodic stripping voltammetry (DPASV) at palladium particles‐impregnated natural phosphate modified carbon paste electrodes (Pd‐NP‐CPE). The surface of modified electrode was characterized using SEM, infrared spectroscopy, X‐ray diffraction and electrochemical analysis. All experimental variables involved in the voltammetric stripping method were optimized. The detection limit was found to be 4.99×10^?8 mol L^?1 (S/N=3) that is not different to the permitted value for Hg(II) in water reported by the Environmental Protection Agency (EPA). The proposed electrode exhibits good applicability for monitoring Hg(II) in tap and wastewater.     

Catalytic Adsorptive Stripping Voltammetry of Cobalt in the Presence of Dimethylglyoxime and Nitrite at In Situ Plated Lead–Copper Film Electrode

A lead‐copper film electrode was proposed for Co(II) determination by catalytic adsorptive stripping voltammetry. The electrode was plated in situ and hence the exchange of a solution after plating step was not required. At optimized conditions the calibration graph for Co(II) was linear from 5×10^?10 to 2×10^?8 mol L^?1 for accumulation time of 15 s. The relative standard deviation for Co(II) determination at concentration 5×10^?9 mol L^?1 was 4.1%. The detection limits for Co(II) were 1.2×10^?10 and 1.0×10^?11 mol L^?1 for an accumulation time of 15 and 180 s, respectively. The method was applied to Co(II) determination in certified reference material and other water samples.     

Amino‐Containing Ultrafine Organosilica‐Nanoparticle‐Modified Au Electrode for the Determination of Cu(II) Ions

Using 3‐Aminopropyltriethoxysilane(APTES) as a single silica source, an amino‐rich ultrafine organosilica‐nanoparticle‐modified Au electrode was fabricated, following the formation of (3‐mercaptopropyl)‐trimethoxysilane (MPTS) monolayer on Au surface (MPTS/Au). With cetyltrimethylammonium bromide as an additive, APTES‐based gel particles on the electrode have a narrow particle size distribution of 4–7 nm and “crystal‐like” structure. AFM and electrochemical characterization confirmed the successful grafting of APTES nanoparticles on MPTS/Au. The APTES/MPTS/Au electrode is highly sensitive for the detection of copper(II) ions with a detection limit as low as 1.6×10^?12 mol L^?1 (S/N>3) by square wave voltammetry. The current is linear to copper(II) concentration between 1.6×10^?12 and 6.25×10^?10 mol L^?1.     

Double Deposition and Stripping Steps for Trace Determination of Au(III) Using Anodic Stripping Voltammetry

A new way of decreasing the detection limit ‐ double deposition and stripping steps was proposed to determine trace amounts of gold(III) by anodic stripping voltammetry. Two carbon composite electrodes that differed drastically in their surface areas were used for the measurements. The calibration graph was linear from 1×10^?9 to 1×10^?8 mol L^?1 following deposition time of 300 s at the first and the second electrode. The detection limit was found to be 2.3×10^?10 and 1.4×10^?11 mol L^?1 for deposition time 600 and 2400 s, respectively. It is the lowest detection limit obtained so far for gold(III) determination in stripping voltammetry.     

Water hyacinth modified carbon paste electrode for simultaneous electrochemical stripping analysis of Cd (II) and Pb (II)

In this study, we demonstrated a highly sensitive electrochemical sensor for the simultaneous detection of Pb (II) and Cd (II) in aqueous solution using carbon paste electrode modified with Eichhornia crassipes powder by square wave anodic stripping voltammetry. The effect of modifier composition, pH, preconcentration time, reduction potential and time, and type of supporting electrolyte on the determination of metal ions were investigated. Pre-concentration on the modified surface was performed at open circuit. The modified electrode exhibited well-defined and separate stripping peaks for Pb (II) and Cd (II). Under optimum experimental conditions, a linear range for both metal ions was from 10 to 5000 μg L^?1 with the detection limits of 4.9 μg L^?1, 2.1 μg L^?1 for Cd(II) and Pb (II), respectively. The modified electrode was found to be sensitive and selective when applied to determine trace amounts of Cd (II) and Pb (II) in natural water samples.     

Simultaneous Adsorptive Cathodic Stripping Voltammetric Determination of Nickel(II) and Cobalt(II) at an In Situ Bismuth‐Modified Gold Electrode

A study on the simultaneous determination of Ni(II) and Co(II) dimethylglyoximates (Ni‐DMG and Co‐DMG) through adsorptive cathodic stripping voltammetry at an in situ bismuth‐modified gold electrode (Bi‐AuE) is reported. The key operational parameters, such as Bi(III) concentration, accumulation potential and accumulation time were optimized and the morphology of the Bi‐microcrystals deposited on the Au‐electrode was studied. The Bi‐AuE allowed convenient analysis of trace concentrations of solely Ni(II) or of Ni(II) and Co(II) together, with cathodic stripping voltammograms characterized by well‐separated stripping peaks. The calculated limit of detection (LOD) was 40 ng L^?1 for Ni(II) alone, whereas the LOD was 98 ng L^?1 for Ni(II) and 58 ng L^?1 for Co(II), when both metal ions were measured together. The optimized method was finally applied to the analysis of certified spring water (NIST1640a) and of natural water sampled in the Lagoon of Venice. The results obtained with the Bi‐AuE were in satisfactory agreement with the certified values and with those provided by complementary techniques, i.e., ICP‐OES and ICP‐MS.     

A Study of the Determination of Cu(II) by Anodic Stripping Voltammetry on a Novel Nylon/Carbon Fiber Electrode

In this work we report a new electrode material formed by injection‐moulding of a conducting polymer consisting of carbon fibers in a Nylon matrix. This material is highly conductive, inexpensive, easy to mould in different shapes and requires minimal pretreatment. The electrode was tested as a mercury‐free sensor for the trace determination of Cu(II) by anodic stripping voltammetry (ASV). The deposition and stripping behavior of copper on the conducting material was initially studied by cyclic voltammetry and the chemical and instrumental parameters of the determination were investigated. The electrode has been shown to be suitable for the determination of Cu(II) in the range 8 μg L^?1 to 30 mg L^?1 (with deposition times ranging from 30 s to 10 min) with a relative standard deviation of 2.2% (at the 0.5 mg L^?1 level) and a limit of detection of 8 μg L^?1 Cu(II) for 10 min of accumulation (at a S/N ratio of 5). The electrode was, finally, applied to the determination of copper in tap‐water, pharmaceutical tablets and bovine serum with recoveries of 97.4, 94.9 and 93.4%, respectively     

Determination of Atrazine in Natural Water Samples by Differential Pulse Adsorptive Stripping Voltammetry Using a Bismuth Film Electrode

A new method using differential pulse adsorptive stripping voltammetry for the determination of atrazine (ATZ) in natural water samples using a bismuth film electrode (BiFE) is proposed. The calibration curve was linear in the atrazine concentration range from 6.7×10^?7 to 2.0×10^?5 mol L^?1, with a limit of detection (LOD) of 1.4×10^?7 mol L^?1. The proposed electrode was applied for atrazine determination with satisfactory results compared with a high‐performance liquid chromatography method (HPLC).     

Pt‐Nanoparticle Incorporated Carbon Paste Electrode for the Determination of Cu(II) Ion by Anodic Stripping Voltammetry

Pt‐nanoparticles were synthesized and introduced into a carbon paste electrode (CPE), and the resulting modified electrode was applied to the anodic stripping voltammetry of copper(II) ions. The synthesized Pt‐nanoparticles were characterized by cyclic voltammetry, scanning electron microscopy and X‐ray photoelectron spectroscopy techniques to confirm the purity and the size of the prepared Pt‐nanoparticles (ca. 20 nm). This incorporated material seems to act as catalysts with preconcentration sites for copper(II) species that enhances the sensitivity of Cu(II) ions to Cu(I) species at a deposition potential of ?0.6 V in an aqueous solution. The experimental conditions, such as, the electrode composition, pH of the solution, pre‐concentration time, were optimized for the determination of Cu(II) ion using as‐prepared electrode. The sensitivity changes on the different binder materials and the presence of surfactants in the test solution. The interference effect of the coexisted metals were also investigated. In the presence of surfactants, especially TritonX‐100, the Cu(II) detection limit was lowered to 3.9×10^?9 M. However, the Pt‐nanoparticle modified CPE begins to degrade when the period of deposition exceeds to 10 min. Linear response for copper(II) was found in the concentration range between 3.9×10^?8 M and 1.6×10^?6 M, with an estimated detection limit of 1.6×10^?8 M (1.0 ppb) and relative standard deviation was 4.2% (n=5).     

Evaluation of Bismuth Modified Carbon Thread Electrode for Simultaneous and Highly Sensitive Cd (II) and Pb (II) Determination

Bismuth film modified and chemically activated carbon micro‐thread electrodes were investigated for the simultaneous determination of Cd(II) and Pb(II) using square wave anodic stripping voltammetry. The carbon thread electrode was characterised using both surface and electrochemical techniques. Electrochemical impedance spectroscopy (EIS) studies demonstrated that the H₂SO₄/IPA‐treated carbon thread electrode showed a much improved resistance response (R_ct=23 Ω) compared to the IPA‐untreated carbon thread (R_ct=8317 Ω). Furthermore, parameters such as the effect of deposition potential, deposition time and Bi(III) concentration were explored using square wave voltammetry. Detection limits (S/N=3) for Cd(II) and Pb(II) were found to be 1.08 µg L^?1 and 0.87 µg L^?1, respectively and response was found to be linear over the range 5–110 µg L^?1. The proposed Bi/IPA‐treated carbon thread electrode exhibited a high selectivity towards Cd(II) and Pb(II) even in the presence of a range of heavy metals and is capable of repetitive and reproducible measurements, being attributed to the high surface area, geometry and electrode treatment characteristics. The proposed metal ion sensor was employed to determine cadmium and lead in river water samples and % RSD was found to be 5.46 % and 5.93 % for Cd(II) and Pb(II) respectively (n=3). Such facile sensing components favour the development of cost effective portable devices for environmental sample analysis and electrochemical applications.     

Chemical Speciation of Antimony(III and V) in Water by Adsorptive Cathodic Stripping Voltammetry Using the 4‐(2‐Thiazolylazo) – Resorcinol

A simple adsorptive cathodic stripping voltammetry method has been developed for antimony (III and V) speciation using 4‐(2‐thiazolylazo) – resorcinol (TAR). The methodology involves controlled preconcentration at pH 5, during which antimony(III) – TAR complex is adsorbed onto a hanging mercury drop electrode followed by measuring the cathodic peak current (I_p,c) at ?0.39 V versus Ag/AgCl electrode. The plot of I_p,c versus antimony(III) concentration was linear in the range 1.35×10^?9–9.53×10^?8 mol L^?1.The LOD and LOQ for Sb(III) were found 4.06×10^?10 and 1.35×10^?9 mol L^?1, respectively. Antimony(V) species after reduction to antimony(III) with Na₂SO₃ were also determined. Analysis of antimony in environment water samples was applied satisfactorily.     

Electrochemical Study of Moroxydine and its Voltammetric Determination with a Silver Amalgam Film Electrode

Moroxydine (Mor.) is an antiviral agent of biguanide structure. The paper presents a new silver amalgam film electrode (Hg(Ag)FE) for determination of Mor. in phosphate buffer, pH 6.2 (LOD=4×10^?9 mol L^?1, LOQ= 1×10^?8 mol L^?1) and in spiked urine using square wave adsorptive stripping voltammetry. It was found that the compound can act as an electrocatalyst not only at hanging mercury drop electrode but also at the Hg(Ag)FE. The electrode mechanism is connected with the hydrogen evolution reaction catalyzed by moroxydine. Adsorption of moroxydine at the mercury electrode was studied and special arrangements of molecules enabling electron transfer of the protonated form of moroxydine is suggested.     

Stripping Voltammetric Determination of Zirconium with Complexing Preconcentration of Zirconium(IV) at a Morin‐Modified Carbon Paste Electrode

A sensitive, selective and economic stripping voltammetry is described for the determination of trace amounts of zirconium at a morin‐modified carbon paste electrode (morin‐MCPE). Zirconium(IV) can be preconcentrated on the surface of the morin‐MCPE due to forming the Zr(IV)–morin complex. The complex produces two second‐order derivative anodic peaks at 0.69 V (vs. SCE) and 0.75 V when linear‐scanning from 0.0 to 1.0 V. The optimum analytical conditions are: 2.2 mol L^?1 HCl, 0.0 V accummulation potential, 90 s accummulation time, 250 mV s^?1 scan rate. A linear relationships between the peak currents at 0.75 V and the Zr(IV) concentration are in the range of 2.0×10^?8 to 3.0×10^?6 mol L^?1. The detection limit is 1.0×10^?8 mol L^?1 (S/N=3) for 120 s accumulation. The RSD for determination of 4.0×10^?7 mol L^?1 Zr(IV) is 4.8% (n=8). The proposed method has been applied to determine zirconium in ore samples, unnecessarily extracted.     

Adsorptive stripping voltammetry of nickel at a bare glassy carbon electrode

A bare glassy carbon electrode is applied to nickel determination by adsorptive stripping voltammetry in the presence of dimethylglyoxime as a complexing agent. A procedure of nickel determination and electrode regeneration was proposed. The calibration graph for Ni(II) for an accumulation time of 120?s was linear from 2?×?10^?9 to 1?×?10^?7?mol?L^?1. The detection limit was 8.2?×?10^?10?mol?L^?1. The relative standard deviation for a solution containing 2?×?10^?8?mol?L^?1 of Ni(II) was 4.1%. The proposed procedure was applied for Ni(II) determination in certified water reference materials.     

The Electrochemical Detection of Arsenic(III) at a Silver Electrode

A study of three electrode substrates namely gold, platinum and silver, for arsenic detection via anodic stripping voltammetry is reported. Hitherto it has been accepted that gold is the most suitable metallic surface for use in this context, as suggested by Forsberg and co‐workers (Forsberg, G.; O'Laughlin, J. W.; Megargle, R. G. Anal. Chem. 1975, 47, 1586.). We revisit these experiments and find that by switching from hydrochloric acid to nitric acid the oxidation of silver that had previously masked the arsenic stripping signal at this surface is shifted considerably enough to allow a clear, analytically reliable As(III) stripping signal to be detected. In contrast to silver and gold platinum is found to have poor performance as an electrode substrate for arsenic detection. Using ASV a LOD of 6.3×10^?7 M is found for As(III) detection at a silver electrode, similar to that which we have previously reported at a gold electrode (A. O. Simm, C. E. Banks and R. G. Compton. Electroanalysis, 2005, 17, 335.) The use of ultrasound was then investigated to further reduce the LOD, which was found to be 1.4×10^?8 M. Apart from reduced cost of silver it also has an added advantage over gold in that it has a higher hydrogen reduction overvoltage enabling a 100 mV more negative deposition potential to be used before the onset of hydrogen evolution when compared to a gold electrode.     

Determination of Blasticidin S in Spiked Rice Using SW Voltammetry with a Renewable Silver Amalgam Film Electrode

Blasticidin S (BS) was determined in spiked rice samples by square wave voltammetry (SWV) and square wave stripping voltammetry (SWSV) using a cyclic renewable silver amalgam film electrode (Hg(Ag)FE). It was found that the compound can act as an electrocatalyst. In Britton? Robinson buffer at pH 7.0 a signal connected with the hydrogen evolution reaction was detected at ?1.2 V versus Ag/AgCl. Validation of the method was carried out. The detection and quantification limits were found to be 2.13×10^?8 mol L^?1; 7.10×10^?8 mol L^?1 for SWV and 2.65×10^?9 mol L^?1; 8.85×10^?9 mol L^?1 for SWSV, respectively.