Platinum Ultramicroelectrodes Modified with Electrogenerated Surfactant‐Templated Mesoporous Organosilica Films: Effect of Film Formation Conditions on Its Performance in Preconcentration Electroanalysis

Pt µdisc electrodes have been modified by mesoporous organosilica thin films by electrochemically assisted self‐assembly (EASA) of mercaptopropyltrimethoxysilane (MPTMS), tetraethoxysilane (TEOS), and the surfactant cetyltrimethylammonium bromide (CTAB). The EASA process involves the generation of hydroxide ions at the electrode/solution interface, upon the application of a cathodic current density, leading to TEOS and MPTMS polycondensation around the CTAB template and concomitant growing of a thiol‐functionalized mesoporous film onto the electrode surface. The experimental conditions (current density, deposition time, silane concentration and molar ratio between surfactant template and silane) were optimised to form a thin and permeable film likely to be used in preconcentration electroanalysis. The morphology of the film electrodes were characterised by scanning electron microscopy. The permeability properties of the modified Pt µdisc electrodes have been evidenced by cyclic voltammetry using Ru(NH₃)₆³⁺ as a redox probe. The best parameters identified for the film preparation are a current density of ? 8 mA cm^?2 applied for 15 s in a solution containing 110 mM of hydrolysed silane precursors and 70.4 mM of CTAB. Pt µdisc electrodes modified in these conditions were used for the open‐circuit preconcentration of Hg(II) species prior to their detection by anodic stripping voltammetry in a mercury‐free solution. In the optimized conditions, a sensitivity of 14.3 mA cm^?2 µM^?1 was obtained for the 0.02–0.08 µM concentration range. The analytical performance of such organosilica films could decay by up to two orders of magnitude for the materials prepared in conditions other than the optimized ones, highlighting the need for a fine control of the deposition parameters to elaborate sensors based on such modified ultramicroelectrodes.     

The effect of interface electrostatic interaction based on acid–base theory on friction behavior

Fluorine‐containing amorphous carbon films [fluoring‐containing diamond‐like carbon (F‐DLC)] were fabricated on Si wafer by direct current plasma enhanced chemical vapor deposition (dc‐PECVD) technique using CF₄ and Ar as gas sources, confirmed by XPS and Raman analyses. The friction tests were carried out on a rotating ball‐on‐disk apparatus in high vacuum atmosphere (≤5.0 × 10^?4 Pa) at the load of 0.5 N selecting glass (mainly containing silicon–oxygen tetrahedron structure) and Al₂O₃ with the same hardness and surface roughness as the counterpart balls. The results indicate that glass/F‐DLC results in lower friction coefficient of 0.14 than that of the Al₂O₃/F‐DLC (0.20). At the same time, no wear was occurred, and the transfer layer was not formed on the counterpart ball for glass/F‐DLC, while the wear of Al₂O₃/F‐DLC is slightly larger than that of glass/F‐DLC. However, just like the glass ball, there is no formation of transfer layer on the Al₂O₃ ball surface. Furthermore, the chemical state of fluorine in the film after friction, which mainly existed in the form of the C–CF and C–F bonds, did not change compared with the F‐DLC film, while the fluorine content has changed significantly. As a result, it is assumed that interface electrostatic interaction based on acid–base theory plays an extremely important role in the process of friction. Copyright © 2017 John Wiley & Sons, Ltd.     

Construction and Characterization of Ru(II)Tris(bipyridine)‐Based Silica Thin Film Electrochemiluminescent Sensors

Ru(II) tris‐bipyridine based ECL sensors were produced by embedding the complex inside silica glass thin films deposited via a sol‐gel dipping procedure on K‐glass conducing substrates. Films were prepared starting from a pre‐hydrolyzed ethanolic solution of Si(OC₂H₅)₄ and Ru(bpy)₃Cl₂. Transparent, crack‐free and homogeneous reddish silica layers, having a thickness of 200±20 nm, were obtained. The films, either deposited at room temperature or thermally annealed at 100, 200 and 300 °C for 30 h, were structurally and chemically characterized. Ru(bpy)₃Cl₂ thermal stability was previously checked by thermogravimetric analysis (TGA). The films were investigated by X‐Ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS) and UV‐vis spectroscopy. XPS in‐depth profiles revealed a homogeneous distribution of the ruthenium complex inside the silica thin layers. SIMS data suggested that the embedded Ru(bpy)₃Cl₂ did not react with oxygen inside the oxygen‐rich silica matrix to give Ru‐O bonds. Electrochemical and ECL characterization of the thin film electrodes were made by means of cyclic voltammetry (CV) and controlled potential step experiments. The ECL sensor showed a diffusive redox behavior of the Ru(bpy)₃²⁺/Ru(bpy)₃³⁺ system. Light emission produced from the reaction between oxalic acid and the electrogenerated Ru(bpy)₃³⁺ was larger and stable when thermally treated electrodes were used after a suitable hydration period. The 300 °C treated sample was the best performing sensor both in terms of low complex leakage and sensitivity. Calibration plots relative to oxalic acid were obtained both in stationary and in flowing solutions in the concentration range 2×10^?6?3×10^?4 M. A linear behavior appeared in the former case, while in the latter a slight curvature was evident as a consequence of a finite diffusion time of the analyte inside the thin film. The signal repeatability, obtained by multiple 100 μL of 10^?5 M oxalic acid injections in flowing solutions, was better than 4%. The obtained detection limit (computed as three times the standard deviation of the base‐line noise) was 10^?6 M as oxalic acid.     

Superlubricity behaviors of Si3N4/DLC Films under PAO oil with nano boron nitride additive lubrication

The tribological properties of Si₃N₄ ball sliding against diamond‐like carbon (DLC) films were investigated using a ball‐on‐disc tribometer under dry friction and oil lubrications, respectively. The influence of nano boron nitride particle as lubricant additive in poly‐α‐olefin (PAO) oil on the tribological properties of Si₃N₄/DLC films was evaluated. The microstructure of DLC films was measured by Raman spectroscopy and X‐ray photoelectron spectroscopy. The experimental results show coefficient of friction (COF) of Si₃N₄/DLC films was as low as 0.035 due to the formation of graphite‐like transfer films under dry friction condition. It also indicates that the tribological properties of Si₃N₄/DLC films were influenced significantly by the viscosity of oil and the content of nano boron nitride particle in PAO oil. COF increases with the viscosity of PAO oil increasing. Si₃N₄/DLC films exhibit the superlubricity behaviors (μ=0.001 and nonmeasurable wear) under PAO 6 oil with 1.0 wt% nano boron nitride particle lubrication, indicating that the improved boundary lubrication behaviors have indeed been responsible for the significantly reduced friction. Nano boron nitride additive is used as solid lubricant‐like nano scale ball bearing to the pointlike contact and a soft phase bond with the weak van der Waals interaction force on the contact surface to improve the lubrication behaviors of Si₃N₄/DLC films. The potential usefulness of nano boron nitride as lubricant additive in PAO oil for Si₃N₄/DLC films has been demonstrated under oil lubrication conditions. The present work will extend the wide application of nano particle additive and introduce a new approach to superlubricity under boundary lubrication in future technological areas. Copyright © 2013 John Wiley & Sons, Ltd.     

The high‐temperature tribological properties of Si‐DLC films

The tribological properties of Silicon‐containing diamond‐like‐carbon (Si‐DLC) films, deposited by magnetron sputtering Si target in methane/argon atmosphere, were studied in comparison with diamond‐like‐carbon (DLC) films. The DLC films disappeared because of the oxidation in the air at 500 °C, whereas the Si‐DLC films still remained, implying that the addition of Si improved significantly the thermal stability of DLC films. Retarded hydrogen release from DLC film at high temperature and silicon oxide on the surface might have contributed to lower friction coefficient of the Si‐DLC films both after annealing treatment and in situ high‐temperature environment. Copyright © 2012 John Wiley & Sons, Ltd.     

Impact of high N2 flow ratio on the chemical and morphological characteristics of sputtered N‐DLC films

Because of their outstanding characteristics, diamond‐like carbon (DLC) thin films have been recognized as interesting materials for a variety of applications. For this reason, the effects of the incorporation of different elements on their fundamental properties have been the focus of many studies. In this work, nitrogen‐incorporated DLC films were deposited on Si (100) substrates by DC magnetron sputtering of a graphite target under a variable N₂ gas flow rate in CH₄ + N₂ + Ar gas mixtures. The influence of high N₂ flow ratios (20, 40 and 60%) on the chemical, structural and morphological properties of N‐DLC films was investigated. Different techniques including field emission gun‐equipped scanning electron microscope (FEG‐SEM), energy‐dispersive X‐ray spectroscopy (EDS), atomic force microscopy (AFM), profilometry, Rutherford backscattering spectrometry (RBS) and Raman spectroscopy (325‐nm and 514‐nm excitation) were used to examine the properties of the N‐DLC films. Thus, the incorporation of nitrogen was correlated with the morphology, roughness, thickness, structure and chemical bonding of the films. Overall, the results obtained indicate that the fundamental properties of N‐DLC films are not only related to the nitrogen content in the film but also to the type of chemical bonds formed. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of Poly(amine)s on the Redox Properties of Carboxymethylcellulose and Ferrocene‐modified Poly(amine) Layer‐by‐Layer Films

Multilayer films consisting of carboxymethylcellulose (CMC) and ferrocene‐modified poly(ethyleneimine) (Fc‐PEI) or poly(allylamine hydrochloride) (Fc‐PAH) were successfully prepared on a gold electrode to examine their redox properties. The redox current of (Fc‐PEI/CMC)_n film‐coated electrodes increased with the number of layers, while the (Fc‐PAH/CMC)_n film‐coated electrodes exhibited increased response only for the first eight bilayers. The (Fc‐PEI/CMC)_n and (Fc‐PAH/CMC)_n films deposited on the surface of Fc‐free multilayer film‐coated electrodes also showed a redox response. The (PEI/CMC)₅ film‐coated electrode showed redox responses in Fc‐PEI and Fc‐PAH solutions, confirming the uptake of the Fc‐polymers in the inner film. In contrast, the uptake of the Fc‐polymers in the (PAH/CMC)₅ film was severely suppressed, suggesting that different permeability of (PEI/CMC)₅ and (PAH/CMC)₅ films.     

Effects of sputtering current on the bonding structure and mechanical properties of diamond‐like carbon films deposited by MFPUMST

Diamond‐like carbon (DLC) films on glass wafers were produced by middle frequency pulsed unbalanced magnetron sputtering technique (MFPUMST) at different sputtering current. The chemical bonding of carbon characterized by Raman spectroscopy and X‐ray photoelectron spectroscopy (XPS) show that the sp³ fraction in DLC films increases with increasing sputtering current from 100 to 300 mA, and then decreases above 300 mA. Mechanical properties like nano‐hardness and elastic recovery for these films under different sputtering currents analyzed by a nano‐indentation technique show the same tendency that nano‐hardness and elastic recovery increase with increasing sputtering current from 100 to 300 mA, and then decrease with increasing sputtering current from 300 to 400 mA. These results indicate that the sp³ fraction in the prepared DLC films is directly related to nano‐hardness and elastic recovery. The results shown above indicate that the parameter of the preparation—sputtering current has a strong influence on the bonding configuration of the deposited DLC films. The mechanism of sputtering current on the sp³ fraction is discussed in this paper. Copyright © 2009 John Wiley & Sons, Ltd.     

A Solid‐State Electrochemiluminescence Immunosensor Based on MWCNTs‐Nafion and Ru(bpy)32+/Nano‐Pt Nanocomposites for Detection of α‐Fetoprotein

A approach was successfully employed for constructing a solid‐state electrochemiluminescence (ECL) immunosensor by layer‐by‐layer self‐assembly of multiwall carbon nanotubes (MWCNTs)‐Nafion composite film, Ru(bpy)₃²⁺/nano‐Pt aggregates (Ru‐PtNPs) and Pt nanoparticles (PtNPs). The influence of Pt nanoparticles on the ECL intensity was quantitatively evaluated by calculating the electroactive surface area of different electrodes with or without PtNPs to immobilize Ru(bpy)₃²⁺. The principle of ECL detection for target α‐fetoprotein antigen (AFP) was based on the increment of resistance after immunoreaction, which led to a decrease in ECL intensity. The linear response range was 0.01–10 ng mL^?1 with the detection limit of 3.3 pg mL^?1. The immunosensor exhibited advantages of simple preparation and operation, high sensitivity and good selectivity.     

Electrochemical behaviour of Ni, Cu, Ag, Pt and glassy carbon electrodes in triethylamine-tris(hydrogen fluoride) medium

Voltammetric responses of Ni, Cu, Ag, Pt and glassy carbon (GC) electrodes in triethylamine-tris(hydrogen fluoride) medium in the anodic as well cathodic potential region were investigated. AAS as well as SEM measurements were also made to ascertain the dissolution rate and surface transformation due to fluoride film formation on the electrode surfaces. On Ni, bulk NiF₂ film growth occurs only around 4.0 V following a thin NiF₂ monolayer formation around 0 V. The NiF₂ film shows very little solubility in the medium. Monolayer and bulk CuF₂ phases are formed quite close to each other on Cu during anodic polarization. The anodically formed CuF₂ dissolves to the extent of 12% in this medium. AgF formation follows a different mechanism during the first and subsequent anodic sweeps. The effect of MeCN as well as water addition on the solubility and stability of these fluoride films are also reported. Glassy carbon and Pt electrodes are relatively inert in this medium. Anodic voltammetric responses for other reactive species could be observed only on Pt and GC electrodes. On the cathodic side, all the electrodes show inert behaviour. Electrochemical reduction of PhNO₂, for example, could be observed on all the electrodes. Electronic Publication     

Influence of post‐annealing on a diamondlike carbon film analyzed by Raman spectroscopy

The influence of a post‐annealing treatment on the chemical structure of a diamondlike carbon (DLC) film was clarified by Raman spectroscopy. The DLC films were synthesized by ionized deposition. The structures were elucidated via Raman analysis in conjunction with the sp² cluster model. The as‐prepared DLC film consisted of a dielectric matrix including sp³ carbon, where sp² clusters were floating. When the post‐annealing treatment commenced, especially between 450 and 600°C, carbon─hydrogen bonds were cleaved, and the hydrogen atoms were desorbed from the film, creating defects or dangling bonds. The defects were reactive in growing sp² clusters that were strained with numerous defects because of the restricted degrees of freedom in the solid. As the post‐annealing temperature further increased, the clusters became dominant and the strain was gradually dissolved.     

Corrosion and tribocorrosion behaviour of super‐thick diamond‐like carbon films deposited on stainless steel in NaCl solution

Super‐thick diamond‐like carbon (DLC) film is a potential protective coating in corrosive environments. In the present work, three kinds of DLC films whose thickness and modulation periods are 4 µm and 3, 21 µm and 17 and 21 µm and 7, respectively, were fabricated on stainless steel. The effect of different thickness and modulation periods on corrosion and tribocorrosion behaviour of the DLC‐coating stainless steel was investigated in 3.5 wt% NaCl aqueous solution by a ball‐on‐flat tribometer equipped with a three‐electrode electrochemical cell. The DLC‐coating stainless steel served as a working electrode, and its OCP and potentiodynamic polarization were monitored before and during rubbing. The wear–corrosion mechanism of the DLC films was investigated by SEM. The results showed that the increasing thickness can prolong significantly lifetime of DLC films in NaCl aqueous solution. In particular, the modulation period has a significant impact on the tribocorrosion resistance of the DLC super‐thick films. The study suggested that the increasing thickness of compressive stress layer could suppress film damage by reducing crack propagation rate. Thus, the super‐thick DLC film with thickness of 21 µm and 7 periods presented the best tribocorrosion resistance among all studied films. Copyright © 2016 John Wiley & Sons, Ltd.     

Electrocatalytic Oxidation of Methanol at Lower Potentials on Glassy Carbon Electrode Modified by Platinum and Platinum Alloys Incorporated in Poly(o‐Aminophenol) Film

The electrocatalytic oxidation of methanol at a glassy carbon electrode modified by a thin film of poly(o‐aminophenol) (PoAP) containing Pt, Pt‐Ru and Pt‐Sn microparticles has been investigated using cyclic voltammetry as analytical technique and 0.10 M perchloric acid as supporting electrolyte. It has been shown that the presence of PoAP film increases considerably the efficiency of deposited Pt microparticles toward the oxidation of methanol. The catalytic activity of Pt particles is further enhanced when Ru or specially Sn is co‐deposited in the polymer film. The effects of various parameters such as the thickness of polymer film, concentration of methanol, medium temperature as well as the long term stability of modified electrodes have also been investigated.     

Electrolyte Effects on Charge Transport Behavior of [Os(bpy)2(PVP)10Cl]Cl and [Ru(bpy)2(PVP)10Cl]Cl Redox Polymers in Ultra‐Thin Films of Polyions

Metallopolymer films have important applications in electrochemical catalysis. The alternate electrostatic layer‐by‐layer method was used to assemble films of [Ru(bpy)₂(PVP)₁₀Cl]Cl (denoted as ClRu‐PVP) and [Os(bpy)₂(PVP)₁₀Cl]Cl (ClOs‐PVP) metallopolymers onto pyrolytic graphite electrodes. Film thickness estimated by quartz crystal microbalance was 6–8 nm. The effects of pH, electrolyte species and concentration on the electrochemical properties of these electroactive polymers were studied using cyclic voltammetry (CV). Behavior in various electrolytes was compared. Also the mass changes within the ultra‐thin film during redox of Os^2+/3+ were characterized by in situ electrochemical quartz crystal microbalance (EQCM). The results indicate rapid reversible electron transfer, and show that both ClRu‐PVP and ClOs‐PVP have compact surface structures while ClOs‐PVP is a little denser than ClRu‐PVP. Although hydrogen ions do not participate in the chemical reaction of either film, the movement of Na⁺ cation and water accompanies the redox process of ClOs‐PVP films.     

The influence of Ti plasma etching pre-treatment on mechanical properties of DLC film on cemented carbide

The pre-treatment of substrate surface had been a key part of DLC film preparation to improve mechanical and tribological properties. Ti plasma etching pre-treatment was investigated in this paper as a new effective surface pre-treatment method to substitute transition layer. This pre-treatment used high-energy Ti plasma to impact substrate surface. Ti plasma etched the substrate to a depth of 407 nm and increased the roughness from 1.36 to 40.39 nm. A trace layer of substrate, together with cobalt, oxides, and other impurities, was removed. Ti plasma broke some top WC crystals and combined with the free carbon ions separating from the substrate. A DLC film was deposited on the etched surface. Compared with DLC films deposited on the untreated substrate and Ti transition layer, the DLC film on the Ti plasma etched substrate had best adhesion strength of 34.14 N. The three DLC films had the same sp³ bonding carbon content, but Ti plasma etching treatment could promote the formation of sp³ bonds on the interface of substrate and DLC film. This DLC film had low friction coefficient of 0.12 and low wear rate of 5.11 × 10⁻⁷ mm³/m·N. In summary, Ti plasma etching pre-treatment could significantly improve the adhesion of DLC film and keep its excellent tribological properties.     

Influence of Ionic Strength on Electrochemical Responses of Myoglobin Loaded in Polysaccharide Layer‐by‐Layer Assembly Films

Two polysaccharides hydroxyethyl cellulose ethoxylate (HECE) and hyaluronic acid (HA) were assembled into {HECE/HA}_n layer‐by‐layer films on electrodes. The films were then immersed in myoglobin (Mb) solutions to load Mb into the films. The Mb‐loaded films showed a nearly reversible cyclic voltammetric (CV) peak pair at ?0.34 V vs. SCE in pH 7.0 buffers. The effect of ionic strength in Mb loading solutions and CV testing solutions on the CV response of the films was investigated. The direct electrochemistry of Mb loaded in the films could also be used to electrocatalyze the reduction of oxygen and H₂O₂ in solution.     

Carbon‐ion implantation improves the tribological properties of Co?Cr?Mo alloy against ultra‐high molecular weight polyethylene

Amorphous diamond‐like carbon (DLC) has drawn a great deal of attention for its superior wear properties against ultra‐high molecular weight polyethylene (UHMWPE). Its rate of wear, however, is not necessarily maintained within a specific range. The aim of this study was to evaluate the mechanical features and tribological properties of three types of surfaces: (i) uncoated, (ii) carbon‐ion implantation (CII)‐treated, and (iii) DLC‐film‐coated substrate. The surface alterations were carried out on cobalt–chrome (Co? Cr? Mo) alloy by the plasma‐source ion implantation (PSII) method. The wear properties and friction coefficient were estimated by a pin‐on‐plate wear‐tester. We found, as a result, that the implanted carbon penetrated the substrates in which good adhesion was expected. Though the surface modifications by CII and DLC hardened the surfaces, the surface with DLC was also roughened (R_a = 39 nm). In contrast, the surface modified by CII had a very smooth surface (R_a = 15 nm) and low friction coefficient (ranging from 0.15 to 0.20), resulting in a low rate of wear. Our findings suggest that CII on the Co? Cr? Mo alloy/UHMWPE pair offers potential benefits as a hard coating for artificial total‐joint arthroplasty. Copyright © 2008 John Wiley & Sons, Ltd.     

Luminescent Amphiphilic 2,6‐Bis(1‐alkylpyrazol‐3‐yl)pyridyl Platinum(II) Complexes: Synthesis,Characterization, Electrochemical,Photophysical, and Langmuir–Blodgett Film Formation Studies

Two series of novel platinum(II) 2,6‐bis(1‐alkylpyrazol‐3‐yl)pyridyl (N5Cn) complexes, [Pt(N5Cn)Cl][X] ( 1 – 9 ) and [Pt(N5Cn)(C?CR)][X] ( 10 – 13 ) (X=trifluoromethanesulfonate (OTf) or PF₆; R=C₆H₅, C₆H₄‐p‐CF₃ and C₆H₄‐p‐N(C₆H₅)₂), with various chain lengths of the alkyl groups on the nitrogen atom of the pyrazolyl units have been successfully synthesized and characterized. Their electrochemical and photophysical properties have been studied. Some of their molecular structures have also been determined by X‐ray crystallography. Two amphiphilic platinum(II) 2,6‐bis(1‐tetradecylpyrazol‐3‐yl)pyridyl (N5C14) complexes, [Pt(N5C14)Cl]PF₆ ( 7 ) and [Pt(N5C14)(C?CC₆H₅)]PF₆ ( 13 ), were found to form stable and reproducible Langmuir–Blodgett (LB) films at the air–water interface. The characterization of such LB films has been investigated by the study of their surface pressure–area (π–A) isotherms, UV/Vis spectroscopy, XRD, X‐ray photoelectron spectroscopy (XPS), FTIR, and polarized IR spectroscopy. The luminescence property of 13 in LB films has also been studied.     

Oxidation of methanol at the network film of polyoxometallate-linked ruthenium-stabilized platinum nanoparticles

We explore here the ability of ruthenium hydroxo species to undergo spontaneous deposition on Pt nanoparticles and to form colloidal solutions of oxoruthenium-protected (-stabilized) nanoparticles of Pt. These particles can be spontaneously attracted to carbon substrates, and they form ultrathin self-assembled films. Fabrication of the multilayer network films on electrodes has been achieved by linking the positively charged oxoruthenium-covered Pt clusters with heteropolyanions of tungsten. By repeated alternate treatments in a solution of phosphododecatungstate (PW₁₂O₄₀^3–) and in a colloidal suspension of oxoruthenium-protected (-stabilized) Pt nanoparticles, the film thickness can be increased systematically (layer by layer) to form stable three-dimensional assemblies on carbon electrodes. It is apparent from cyclic voltammetric and chronoamperometric measurements (that were performed at 20 and 60 °C) that the resulting hybrid films show attractive properties towards the oxidation of methanol at fairly low potentials (0.25–0.4 V versus the saturated calomel electrode). With approximately the same loading of oxoruthenium-covered Pt nanoparticles and under analogous conditions, linking or derivatizing the nanoparticles with phosphotungstate leads to the systems higher electrocatalytic activity. It is possible that, in addition to ruthenium hydroxo species, PW₁₂O₄₀^3– exhibits an activating effect on dispersed Pt particles. An alternative explanation may involve the possibility of different morphologies of the catalytic films in the presence and absence of phosphotungstate anions.Dedicated to Zbigniew Galus on the occation of his 70th birthday     

Polyallylammonium Ferrocyanide Films for Trace Water Detection in Halogenated Solvents

Polyallylammonium films with electrostatically bound ferrocyanide were formed by electrochemically reducing ferricyanide ions in the presence of polyallylammonium chloride. These films could be deposited onto the surfaces of Pt, Au or SnO₂ electrodes. In anhydrous organic electrolyte solutions, these films are electroinactive but become electroactive after the addition of trace water. For concentrations of water from 0.0 to 0.12% in chlorinated solvents, the electroactivity is linear with water concentration. The linearity between concentration of water and electroactivity can be exploited to develop a subsaturation trace water sensor.