Simultaneous Determination of Lead,Copper, and Mercury Free from Macromolecule Contaminants by Square Wave Stripping Voltammetry

Abstract

A novel approach for the voltammetric determination of Pb²⁺, Cu²⁺, and Hg²⁺ in the presence of macromolecule contaminants was developed. An Au nanoparticles array was directly electrodeposited onto the gold electrode surface followed by a further modification of a mercaptoethanesulfonate (MES) monolayer. Square wave stripping voltammetry (SWSV) of Pb²⁺, Cu²⁺, and Hg²⁺ was performed on the doubly modified electrode. The electrodeposited gold nanoparticles provided a significantly improved sensitivity. Simultaneously, the MES monolayer efficiently prevented the macromolecules accessing the electrode surface. Compared with the bare gold electrode, the doubly modified electrode has the ability to detect metal ions in the presence of macromolecule contaminants, even when their concentration reach 100 ppm. Under the optimal conditions, the detection limits of 0.16, 0.15, and 0.14 ppb for Pb²⁺, Cu²⁺, and Hg²⁺ were obtained, respectively. The calibration graphs were linear in the concentration range of 1–100 ppb. The results of the analysis of a real metallurgy wastewater sample were reported. The electrode system has a great potential for the direct determination of trace metals in the complex environment and biological samples.     

Simultaneous Detection of Heavy Metals by Anodic Stripping Voltammetry Using Carbon Nanotube Thread

Carbon nanotube (CNT) threads are a type of CNT arrays that consist of super long CNTs. CNT threads inherit the advantages of CNTs, while avoiding the potential toxicity caused by individual CNTs. Electrodes based on CNT threads were fabricated and used for simultaneous detection of trace levels of Cu²⁺, Pb²⁺ Cd²⁺ and Zn²⁺ by anodic stripping voltammetry (ASV). The detection limits are 0.27 nM, 1.5 nM, 1.9 nM and 1.4 nM for Cu^2+, Pb²⁺, Cd²⁺ and Zn²⁺, respectively, in 0.1 M acetate buffer pH 4.5. The CNT thread electrode gives well‐defined, reproducible and sharp stripping signals for individual and simultaneous detection of heavy metals.     

A reactive electrode (reactrode) for the voltammetric determination of heavy metals in laboratories and for use as a passive monitor in remote analysis

The use of a reactive electrode (reactrode) consisting of graphite, a solid ion exchanger (HYPHAN) and paraffin for the batch analysis of Cd²⁺, Cu²⁺, Pb²⁺ and Hg²⁺ in aqueous samples and as a passive monitor for these metal ions is described. The metal ions are accumulated on the reactrode surface at an open-circuit potential in an ion-exchange reaction. After the accumulation, the ion exchanger-bonded metal ions are reduced to the metals which remain on the electrode surface. In a following step, the metals are anodically dissolved which is recorded by differential-pulse voltammetry. The 3s detection limits for the analysis of drinking water are: 1.1×10^-7 mol/l for Pb²⁺, 5×10^-8 mol/l for Hg²⁺ and 2.4×10^-7 mol/l for Cu²⁺.The reactrode developed can be used for the passive monitoring of heavy metals in aqueous streams if the reactrode is mounted in a wall-jet cell which is part of a flow-through system. Using this arrangement, it has been possible to determine Hg²⁺, Cu²⁺ and Pb²⁺ in drinking water after 20 hours of accumulation.     

Simultaneous Determination of Cadmium,Lead, Copper and Mercury Ions Using Organofunctionalized SBA‐15 Nanostructured Silica Modified Graphite–Polyurethane Composite Electrode

A new sensor has been developed for the simultaneous detection of cadmium, lead, copper and mercury, using differential pulse and square wave anodic stripping voltammetry (DPASV and SWASV) at a graphite–polyurethane composite electrode with SBA‐15 silica organofunctionalized with 2‐benzothiazolethiol as bulk modifier. The heavy metal ions were preconcentrated on the surface of the modified electrode at ?1.1 V vs. SCE where they complex with 2‐benzothiazolethiol and are reduced to the metals, and are then reoxidized. Optimum SWASV conditions lead to nanomolar detection limits and simultaneous determination of Cd²⁺, Pb²⁺, Cu²⁺ and Hg²⁺ in natural waters was achieved.     

In-situ electrochemical and piezogravimetric studies on the application of macrocyclic resorcinarene tetramer in the development of chemically-modified heavy metals ions detection platform in aqueous media

The new application of C-dec-9-enylcalix[4]resorcinarene (R₁), as an ionophore to detect heavy metals (HMs) cations (Cd²⁺, Hg²⁺, Cu²⁺, and Pb²⁺) in the aqueous media has been investigated through the preparation of an effective mass-sensitive sensor via the exploitation of a flow-type QCM-I technique. By adjusting the ions’ amounts in model solutions over a wide range of concentrations, acquired changes in the oscillating frequency related to the loading of metal ions on the sensor’s surface were gained, and thus favorable metrological parameters displaying the lowest detection limit (LOD) associated with copper ions (10 ppb). Simultaneously, a novel voltammetric sensor was prepared by modifying gold screen-printed electrodes (SPEs) with R₁. Electrochemical characterization employing CV, SWV, and EIS was carried out, showing the success of the electrode modification. Then, the experimental conditions of supporting electrolyte, pH, accumulation time, and accumulation potential were optimized to achieve an enhanced detection. The R₁@SPE sensor simultaneously detected the HMs (Cd²⁺, Hg²⁺, Cu²⁺, Pb²⁺), and the lowest LOD was associated with Pb²⁺ (0.19 ppb). The selectivity evaluation of the electrochemical sensor was performed by studying the effect of interferences majorly present in water sources (Mg²⁺, Ni²⁺, Zn²⁺, Al³⁺, and K⁺) on the SWV detection signals, and it was revealed that the interfering ions did not affect the simultaneous detection of the studied HMs (RSD less than 5%), the voltammetric sensors also presented excellent repeatability and reproducibility (RSD less than 5%).     

Simultaneous voltammetric analysis of lead,copper and mercury ions by carbon paste electrode based on 1-(3-aminopropyl) imidazole modified polymer

In this study, a carbon paste electrode modified with a novel 1-(3-aminopropyl) imidazole functionalised crosslinked chlorosulfonated poly(styrene)-divinyl benzene polymer was used for selective and sensitive determination of the trace amounts of Pb²⁺, Cu²⁺ and Hg²⁺ ions by square wave anodic stripping voltammetry. The effect of some parameters such as paste composition, pH, preconcentration time, reduction potential and time, type of supporting electrolyte and potential scan rate on the determination of metal ions were investigated to find the optimal conditions. The effective open-circuit accumulation of the studied metal ions was succeeded only by the modification of the carbon paste electrode with functional polymer. For 6 min open-circuit preconcentration, the detection limit of Pb²⁺, Cu²⁺ and Hg²⁺ was found to be 5, 9 and 14 µgL^?1, respectively at 100 mVs^?1. The results confirmed that the lower concentration levels of these trace metal ions can be determined with the increase of preconcentration time and/or potential scan rate. Good detection limits and large dynamic concentration ranges were also obtained for their binary and ternary mixtures. The optimised method was successively applied to determine the concentration of Pb²⁺, Cu²⁺ ions in the tap water sample and Cu²⁺ ion in the waste water sample in the presence of possible interfering species (RSD<1%, recoveries 96–110% for 4 min preconcentration).     

Non-conductive nanomaterial enhanced electrochemical response in stripping voltammetry: The use of nanostructured magnesium silicate hollow spheres for heavy metal ions detection

Nanostructured magnesium silicate hollow spheres, one kind of non-conductive nanomaterials, were used in heavy metal ions (HMIs) detection with enhanced performance for the first time. The detailed study of the enhancing electrochemical response in stripping voltammetry for simultaneous detection of ultratrace Cd²⁺, Pb²⁺, Cu²⁺ and Hg²⁺ was described. Electrochemical properties of modified electrodes were characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The operational parameters which have influence on the deposition and stripping of metal ions, such as supporting electrolytes, pH value, and deposition time were carefully studied. The anodic stripping voltammetric performance toward HMIs was evaluated using square wave anodic stripping voltammetry (SWASV) analysis. The detection limits achieved (0.186 nM, 0.247 nM, 0.169 nM and 0.375 nM for Cd²⁺, Pb²⁺, Cu²⁺ and Hg²⁺) are much lower than the guideline values in drinking water given by the World Health Organization (WHO). In addition, the interference and stability of the modified electrode were also investigated under the optimized conditions. An interesting phenomenon of mutual interference between different metal ions was observed. Most importantly, the sensitivity of Pb²⁺ increased in the presence of certain concentrations of other metal ions, such as Cd²⁺, Cu²⁺ and Hg²⁺ both individually and simultaneously. The proposed electrochemical sensing method is thus expected to open new opportunities to broaden the use of SWASV in analysis for detecting HMIs in the environment.     

Simultaneous detection of cadmium, copper, and lead using a carbon paste electrode modified with carbamoylphosphonic acid self-assembled monolayer on mesoporous silica (SAMMS)

A new sensor was developed for simultaneous detection of cadmium (Cd²⁺), copper (Cu²⁺), and lead (Pb²⁺), based on the voltammetric response at a carbon paste electrode modified with carbamoylphosphonic acid (acetamide phosphonic acid) self-assembled monolayer (SAM) on mesoporous silica (Ac-Phos SAMMS). The adsorptive stripping voltammetry (AdSV) technique involves preconcentration of the metal ions onto Ac-Phos SAMMS under an open circuit, then electrolysis of the preconcentrated species, followed by a square wave potential sweep towards positive values. Factors affecting the preconcentration process were investigated. The voltammetric responses increased linearly with the preconcentration time from 1 to 30 min or with metal ion concentrations ranging from 10 to 200 ppb. The responses also evolved in the same fashion as adsorption isotherm in the pH range of 2-6. The metal detection limits were 10 ppb after 2 min preconcentration and improved to 0.5 ppb after 20 min preconcentration.     

High‐Sensitivity Determination of Lead(II) and Cadmium(II) Based on the CNTs‐PSS/Bi Composite Film Electrode

A high‐sensitivity sensing platform for lead(II) and cadmium(II) based on the bismuth modified carbon nanotubes (CNTs)‐poly(sodium 4‐styrenesulfonate) composite film electrode (CNTs‐PSS/Bi) was fabricated. The composite film CNTs‐PSS/Bi provided remarkably improved sensitivity and reproducibility compared with previously reported CNTs‐modified electrodes. The detection limits were estimated to be 0.04 ppb for lead(II) and 0.02 ppb for cadmium(II) with a preconcentration time of 120 s, respectively. The linear responses of Cd²⁺ and Pb²⁺ were over the ranges of 0.5–50 ppb and 0.5–90 ppb, respectively. Finally, the practical application of the proposed method was verified in the real water sample with satisfactory results.     

Simultaneous Titration of Ternary Mixtures of Pb(II), Cd(II) and Cu(II) with Potentiometric Electronic Tongue Detection

An automatic titration method is reported to resolve ternary mixtures of transition metals (Pb²⁺, Cd²⁺ and Cu²⁺) employing electronic tongue detection and a reduced number of pre‐defined additions of EDTA titrant. Sensors used were PVC membrane selective electrodes with generic response to heavy‐metals, plus an artificial neural network response model. Detection limits obtained were ca. 1 mg L^?1 for the three target ions and reproducibilities 3.0 % for Pb²⁺, 4.1 % for Cd²⁺ and 5.2 % for Cu²⁺. The system was applied to contaminated soil samples and high accuracy was obtained for the determination of Pb²⁺. In the determination Cd²⁺ and Cu²⁺, sample matrix showed a significant effect.     

CC Bonding of Graphene Oxide on 4‐Aminophenyl Modified Gold Electrodes towards Simultaneous Detection of Heavy Metal Ions

This paper studied the electrochemical sensors based on C? C bonding of graphene oxide (GO) on π‐conjugated aromatic group modified gold electrodes for simultaneous detection of heavy metal ions. For comparison, another sensing interface Au‐Ph‐NH‐CO‐GO, in which GO was modified to Au‐Ph‐NH₂ interfaces by amide bonding. On the basis of the principle of heavy metal ions complexation with oxygenated species on GO, the fabricated sensing interfaces were used for the simultaneous determination of Pb²⁺, Cu²⁺ and Hg²⁺. The performance of two sensing interfaces for simultaneous detection of three metal ions was compared. Au‐Ph‐GO sensing interface demonstrated higher sensitivity and better repeatability than Au‐Ph‐NH‐CO‐GO sensing interface.     

Highly selective in situ metal ion determination by hybrid electrochemical "adsorption-desorption" and colorimetric methods

A novel and facile hybrid analytical method coupling electrochemical “adsorption–desorption” and colorimetric analyses was developed to detect heavy metal ions in turbid water samples. The target metal ions were deposited onto an electrode inserted into the original sample, which was referred to as the “adsorption” process. After changing the medium, the concentrated target metal ions were dissolved in a new, clean buffer (blank buffer), which was referred to as the “desorption” process. The concentrations of the target metal ions were measured by colorimetric analyses after the addition of specific indicator amounts. We demonstrated the applicability of this method by detecting Cd²⁺, Pb²⁺ and Cu²⁺ with co-depositing Bi³⁺ on portable screen-printed electrodes (SPEs). A good correlation (correlation coefficient of R = 0.997) was observed between concentrations ranging from 1 to 200 μM and absorbance values. After the multiple “desorption” process, the even better detection limits as low as 10, 10 and 100 nM were achieved for Cd²⁺, Pb²⁺ and Cu²⁺, respectively. The practicality of this hybrid method was confirmed by the detection of Cd²⁺, Pb²⁺ and Cu²⁺ in wastewater samples, and these results were in agreement with inductively coupled plasma atomic emission spectroscopy (ICP-AES). Overall, this hybrid method provides a simple, selective and effective technique for environmental pollutant analyses.     

Electrochemical Determination of Cd2+ and Pb2+ Using NSAID‐mefenamic Acid Functionalized Mesoporous Carbon Microspheres Modified Glassy Carbon Electrode

This paper describes the electrochemical behaviors of Cd²⁺ and Pb²⁺ on the proposed mesoporous carbon microspheres/mefenamic acid/nafion modified glassy carbon electrode (MC/MA/Nafion/GC) studied by square wave anodic stripping voltammetry (SWASV). The prepared material is characterized by XRD, SEM, FTIR, RAMAN and BET analysis. Experimental parameters, such as the deposition potential and time, the pH value of buffer solution were optimized. Under the optimized conditions, the electrode responded linearly to Cd²⁺ and Pb²⁺ in the concentration range from 50 to 300 nM, and the detection limits were 24.2 and 11.26 nM respectively. The sensitivity determined was 0.0623 μA/nM (Cd²⁺) and 0.192 μA/nM (Pb²⁺). Multiple metal ion detection with clear demarcation of peaks was produced by the electrode. Moreover, the modified electrode has possessed good selectivity and reproducibility of Cd²⁺ and Pb²⁺ detection. We also investigated the interference of various anions and surfactants for the detection of Cd²⁺ and Pb²⁺ ions. Finally the modified electrode was used to detect the presence of metal ions in practical samples and the results obtained are comparatively good with respect to AAS.     

Carbon Nanotubes/Ionophore Modified Electrode for Anodic Stripping Determination of Lead

Bifunctional combination of carbon nanotubes and ionophore is introduced for anodic stripping analysis of lead (Pb²⁺). Carbon nanotubes are employed to improve the detection sensitivity due to their excellent electrical conductivity and strong adsorption ability. An ionophore is utilized for its excellent selectivity toward Pb²⁺. The proposed carbon nanotubes/ionophore modified electrode shows improved sensitivity and selectivity for Pb²⁺. Low detection limit (1 nM), wide linear range (5 nM–8 µM) and excellent selectivity over other metal ions (Cd²⁺, Cu²⁺, and Hg²⁺) was obtained. The practical application has been carried out for determination of Pb²⁺ in real water samples.     

Potentiometric Titration of Trace Concentrations of Penicillamine Using Ion Selective Electrodes

Abstract

Penicillamine (PA) has shown promise as a therapeutic agent in the treatment of rheumatoid arthritis (RA), and a sensitive analytical procedure applicable to physiological fluids is needed. PA is a metal chelating agent which forms very strong complexes with heavy metal ions (e.g., Hg²⁺, Cu²⁺, Pb²⁺). This characteristic has been applied to the analytical problem presented. The method developed is based on potentiometric titration of the ligand with a metal ion solution utilizing for endpoint detection an indicator electrode selective for this metal ion. The procedure described used lead (II) as the titrant and a lead (II) selective electrode. Demonstrated precision was ±2.0% when 7.5 μg PA was determined in 50 ml solution.     

An Electrochemical Sensing Platform for the Detection of Lead Ions Based on Dicarboxyl‐Calix[4]arene

A simple and highly sensitive electrochemical sensor COOH−C4 derived from dicarboxyl‐calix[4]arene modified on a screen printed gold electrode (Au) was developed for the determination of lead ions in water samples. A 3‐mercaptopropionic acid (MPA) monolayer was used as a template on the gold electrode for the surface modification with dicarboxyl‐calixarene. The modified electrodes were surface‐characterized using Fourier Transform infrared spectroscopy (FTIR). The data obtained proved the confirmation of each stage of the electrode modification. The electrochemical analyses of the COOH−C4 electrode showed an enhanced electrocatalytic activity and higher current towards Pb²⁺ ions as compared to the bare Au and MPA/Au electrodes. Under optimum conditions, the differential pulse voltammetry response of COOH−C4 displayed a wide linear response ranging from 280–2500 μg/L for Pb²⁺ with a detection limit of 6.2 μg/L. In addition, the fabricated electrode showed a high selectivity and stability towards the Pb²⁺ ions in presence of possible interfering species. The present method was successfully applied to determine Pb²⁺ ions in real samples with satisfactory precision, with a relative standard deviation of 3.12 % and an acceptable recovery of 92 %, which demonstrated the potential application of dicarboxyl‐calix[4]arene modified on electrodes for heavy‐metal sensing.     

Silver nanoparticle loaded on activated carbon and activated carbon modified with 2-(4-isopropylbenzylideneamino)thiophenol (IPBATP) as new sorbents for trace metal ions enrichment

The efficiencies and performances of silver nanoparticle loaded activated carbon modified with 2-(4-isopropylbenzylideneamino)thiophenol (IPBATP-Ag-NP-AC) and activated carbon modified with IPBATP (IPBATP-AC), as new sorbents, were evaluated for separation and preconcentration of Cu²⁺, Zn²⁺, Co²⁺, Cd²⁺ and Pb²⁺ ions from real environmental samples. The retained metals content was reversibly eluted using 5?mL of CH₃COOH (6.0?mol?L^?1) and/or 10?mL of 4.0?mol?L^?1 HNO₃ for IPBATP-Ag-NP-AC and IPBATP-AC, respectively. The experimental parameters influence the recoveries of metal ions including pH, amounts of ligand and supports, condition of eluents, sample and eluent flow rates of has been investigated. The preconcentration factors were found to be 100 for Zn²⁺, Cd²⁺, Co²⁺, Cu²⁺ and 50 for Pb²⁺ ions using IPBATP-Ag-NP-AC, and 50 for Zn²⁺, Cd²⁺, Co²⁺, Cu²⁺ and 25 for Pb²⁺ ions using IPBATP-AC. The detection limit of both SPE-based sorbents was between 1.6–2.5?ng?mL^?1 for IPBATP-AC and 1.3–2.5?ng?mL^?1 for IPBATP-Ag-NP-AC. The proposed methods have been successfully applied for the extraction and determination of the understudy metal ions content in some real samples with extraction efficiencies higher than 90% and relative standard deviations (RSD) lower than 2.4%.     

Voltammetric Simultaneous Determination of Cu2+, Cd2+ and Pb2+ in Full Aqueous Medium Using Organic Nanoparticles of Disulfide Based Receptor

Disulfide based receptor was prepared using single step condensation reaction and suspended into organic nanoparticles to extend its practical application in aqueous samples. The prepared nanoparticles were used for the simultaneous recognition of three different metallic species (Cu²⁺, Cd²⁺, and Pb²⁺) in aqueous media through voltammetric studies. These metals can be determined simultaneously and without interferences from any of the other potential interferent metal ions, as different signals are displayed in cyclic as well as differential pulse voltammograms, with a detection limit of 193.0 nM for Cu²⁺, 52.0 nM for Cd²⁺ and 32.0 nM for Pb²⁺. The study was extended to real sample analysis by preparing the artificial mixtures of said metal ions.     

Hydroxyapatite Wrapped Multiwalled Carbon Nanotubes/Ionic Liquid Composite Electrode: A High Performance Sensor for Trace Determination of Lead Ions

A nanocomposite consisting of multiwalled carbon nanotubes wrapped with hydroxyapatite (HA/MWCNTs) was used in the construction of a new composite paste electrode using an ionic liquid as the binder. The stable surface in aqueous solutions as well as the high sorptive behaviors towards heavy metal ions and the favorable charge transfer make the electrode highly efficient especially for stripping or adsorptive analysis. The analysis of Pb²⁺ as a model of heavy metal ions has been performed. Good sensitivity, detection limit, selectivity and reproducibility were obtained for the suggested sensor. The linear range of the electrode response covered four orders of magnitude (1 nM–10 µM), in two linear ranges. The obtained detection limit for Pb²⁺ was 2×10^?11 M.     

Preconcentration and Determination of Trace Amounts of Heavy Metals in Water Samples Using Membrane Disk and Flame Atomic Absorption Spectrometry

A fast and simple method for preconcentration of Ni^2＋, Cd^2＋, Pb^2＋, Zn^2＋, Cu^2＋ and Co^2＋ from natural water samples was developed. The metal ions were complexed with sodium diethyldithiocarbamate （Na-DDTC）, then adsorbed onto octadecyl silica membrane disk, recovered and determined by FAAS. Extraction efficiency, influence of sample volume and eluent flow rates, effects of pH, amount of Na-DDTC, nature and amount of eluent for elution of metal ions from membrane disk, break through volume and limit of detection have been evaluated. The effect of foreign ions on the percent recovery of heavy metal ions has also been studied. The limit of detection of the proposed method for Ni^2＋, Cd^2＋, Pb^2＋, Zn^2＋, Cu^2＋ and Co^2＋was found to be 2.03, 0.47, 3.13, 0.44, 1.24 and 2.05 ng·mL^-1, respectively. The proposed （DDTC） method has been successfully applied to the recovery and determination of heavy metal ions in different water samples.