Effects of pigments on the volume‐phase‐transition properties of N‐isopropylacrylamide gels as light‐modulation materials

The effects of pigments contained in N‐isopropylacrylamide (NIPAM) gels on their volume‐change properties were investigated. All the NIPAM gel particles, containing various kinds and concentrations of pigments, showed a volume phase transition at 34 °C. No pigment affected the volume‐phase‐transition temperature of the NIPAM gels. As the concentration of the pigment in the NIPAM gels was increased, the amount of the volume change of the NIPAM gels was reduced. The water absorptivity of the NIPAM gels in the swollen state decreased as the pigment concentration increased, whereas the water absorptivity in the shrunken state was almost constant. Reducing the initial monomer concentration of the polymerization of the NIPAM gel increased the water absorptivity in the swollen state. With an increase in the water absorptivity, the volume changes of the NIPAM gels containing pigments were increased. Prototype light modulators in which the NIPAM gel particles containing pigment were dispersed between glass plates were fabricated. The light modulator using the gel particles with improved diameter change (d/d₀ = 2.3, where d and d₀ are the equilibrium diameter and the diameter of the fully shrunken state at 50 °C, respectively) exhibited a larger transmittance change from 8 to 79% than that using the gel particles before the improvement (d/d₀ = 1.7; from 38 to 79%) according to temperature changes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4644–4655, 2006     

Temperature‐induced phase transition of poly(N‐n‐propylacrylamide‐co‐butyl methacrylate‐co‐N,N‐diethylaminoethyl methacrylate)

Terpolymers composed of N‐n‐propylacrylamide (NPAAm), butyl methacrylate (BMA), and N,N‐diethylaminoethyl methacrylate (DEAEMA) were prepared in an attempt to investigate the temperature‐induced phase transition and its mechanism. Poly(NPAAm) showed the lower critical solution temperature (LCST) around 24°C in water. With the incorporation of DEAEMA with NPAAm, the LCST change was characterized by an initial increase. However, the LCST was shifted to the lower temperature at the later stage. This might be explained in terms of hydrophilic/hydrophobic contribution of DEAEMA to the LCST. The swelling behavior of copolymer gel in the various solvents and spin‐lattice relaxation time (T₁) study by NMR strongly suggested the hydrophilic/hydrophobic contribution of DEAEMA to the LCST depending on the local environment. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1407–1411, 1999     

Effect of alkyl substituents structures and added ions on the phase transition of polymers and gels prepared from methyl 2‐alkylamidoacrylates

The effects of structure alteration of alkyl groups and addition of ions to solutions of new thermosensitive polymer series of poly(methyl 2‐alkylamidoacrylate)s were investigated. Potential advantages of the thermosensitive polymers are their simplicity of functionalization and transition temperature control that result from their unique α,α‐disubstituited structures. Poly(methyl 2‐propionamidoacrylate) (PMPA) and poly(methyl 2‐isobutyracrylate) (PMIBA) were thermosensitive polymers, and poly(methyl 2‐acetamidoacrylate) and poly(methyl 2‐n‐butyramidoacrylate) were completely water‐soluble and ‐insoluble, respectively. The PMIBA solution showed endotherm during the phase transition, while endotherm was not detected for PMPA. The difference between the two polymers resulted from the size of the hydrophobic groups. MPA gel was prepared by copolymerization with N,N′‐methylenebis(acrylamide) and temperature‐induced volume change of the gel was continuous. The salting‐out effect of inorganic ions on PMPA solution and MPA gel followed the Hofmeister series. The inorganic (I^? and SCN^?) and organic ions (ⁿPr₄N⁺ and ⁿBu₄N⁺), which showed the salting‐in effect, were indicated to directly interact with PMPA chains. These ions widened the temperature range of the phase transition of the PMPA solutions. This reduced cooperativity of the phase transition was caused by size decrease of cooperative domains, which resulted from the interaction of the ions with the polymer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4942–4952, 2005     

Crystal‐to‐Gel Transformation Stimulated by a Solid‐State E→Z Photoisomerization

The molecule (E)‐(5‐(3‐anthracen‐9‐yl‐allylidene)‐2,2‐dimethyl‐[1,3] dioxane‐4,6‐dione) (E‐ AYAD ) undergoes E→Z photoisomerization. In the solid state, this photoisomerization process can initiate a physical transformation of the crystal that is accompanied by a large volume expansion (ca. 10 times), loss of crystallinity, and growth of large pores. This physical change requires approximately 10 % conversion of the E isomer to the Z isomer and results in a gel‐like solid with decreased stiffness that still retains its mechanical integrity. The induced porosity allows the expanding gel to engulf superparamagnetic nanoparticles from the surrounding liquid. The trapped superparamagnetic nanoparticles impart a magnetic susceptibility to the gel, allowing it to be moved by a magnetic field. The photoinduced phase transition, starting with a compact crystalline solid instead of a dilute solution, provides a new route for in situ production of functional porous materials.     

Synthesis of transition‐metal‐ion‐selective poly(N‐isopropylacrylamide) hydrogels by the incorporation of an Aza crown ether

A functionalized cyclam was synthesized by the attachment of a polymerizable acryloyl group to one of the four nitrogens on the cyclam molecule. The polymerization of the functionalized cyclam was performed with N‐isopropylacrylamide and N,N′‐methylene bisacrylamide, and the gels obtained were studied in the presence of different transition‐metal‐ion solutions. There was a drastic difference in the phase‐transition temperature (T_c) of the poly(N‐isopropylacrylamide) (PNIPAAm)/cyclam gel in comparison with the pure PNIPAAm gel. For the described system, a T_c shift of 15 °C was obtained. The presence of functionalized cyclam increased the hydrophilicity and T_c of the aforementioned polymer gels in deionized water (at pH 6) because of the presence of protonated amino moieties. The PNIPAAm/cyclam gels showed a dependence of the swelling behavior on pH. T_c of the pure PNIPAAm gel was weakly influenced by the presence of any transition‐metal ions, such as Cu²⁺, Ni²⁺, Zn²⁺, and Mn²⁺. The addition of Cu²⁺ or Ni²⁺ to the PNIPAAm/cyclam gel reduced T_c of the polymer gel, and a shift of approximately 12 °C was observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1594–1602, 2003     

Hydration‐mediated effects of saccharide stereochemistry on poly(N‐isopropylacrylamide) gel swelling

To shed new light on the mechanisms of saccharide stereochemistry effect on macromolecules in aqueous solutions, we studied the effect of three monosaccharide stereoisomers, glucose, galactose, and mannose, on the swelling of Poly(N‐isopropylacrylamide) (PNIPA) hydrogels. We equilibrated PNIPA hydrogels in sugar solutions of different concentrations at 25 °C, and determined gel volume and mass swelling ratios, and sugar concentration imbalance. The volume‐phase‐transition occurred at molal concentrations of 0.587 ± 0.004 (galactose), 0.724 ± 0.003 (glucose), and 0.846 ± 0.004 (mannose). The same order of sugars emerged for the gel‐swelling and the magnitude of the sugar concentration‐imbalance, which correlated with sugar isentropic molar compressibility and hydration number. The more hydrated the sugar, the worse a cosolvent it is for the polymer, hence the larger the deswelling and the more negative the sugar concentration imbalance. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Preparation of temperature‐responsive polymer gels physically immobilizing core‐shell type bioconjugates

Poly(N‐isopropylacrylamide) (PNIPAAm) gels are temperature‐responsive polymer gels; and were prepared by redox polymerization of N‐isopropylacrylamide in the presence of N,N′‐methylenebisacrylamide as a crosslinking reagent and core‐shell type bioconjugates, which were core‐crosslinked polyion complex micelles formed from the mixture of bovine pancreas trypsin and poly(ethylene glycol)‐block‐poly(α,β‐aspartic acid). The phase transition temperature of PNIPAAm gels was no change with physically immobilization of bioconjugates. Also, the enzymatic activity of bioconjugates was essentially maintained even in PNIPAAm gels, although enzymatic reaction rate was apparently controlled by temperature, i.e., by the degree of swelling of PNIPAAm gels. Further, the control of enzymatic reaction synchronizing the phase transition of PNIPAAm gels immobilized bioconjugates. PNIPAAm gels could immobilize core‐shell type bioconjugates, and were successfully prepared without interfering with the properties of temperature‐responsive polymer gels and the bionanoreactor. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5942–5948, 2007     

Positron annihilation studies of poly(N‐isopropyl acrylamide) gel in mixed solvents

Positron annihilation lifetime spectroscopy was used to characterize the reentrant volume‐phase‐transition behavior of poly(N‐isopropyl acrylamide) hydrogel in an ethanol/water mixed solvent. The polymer gel was synthesized with γ irradiation. The ortho‐positronium lifetime (τ₃) in the gel slowly increased with an increase in the ethanol content in the mixed solvent. τ₃ was not influenced by the volume phase transition. The ortho‐positronium intensity decreased with the collapse of the gel in an approximately 10% ethanol/water mixture. When swelled in pure ethanol, τ₃ initially increased with the solvent amount in the gel, showing the destruction of intramolecular hydrogen bonding and the relaxation of polymer chains. The lower critical solution temperature of the gel in the 10% ethanol/water mixture was lower than that in pure water, and τ₃ for various solvent contents showed behavior similar to that seen in pure solvent. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1028–1036, 2002     

Pressure‐Induced Bond Rearrangement and Reversible Phase Transformation in a Metal–Organic Framework

Pressure‐induced phase transformations (PIPTs) occur in a wide range of materials. In general, the bonding characteristics, before and after the PIPT, remain invariant in most materials, and the bond rearrangement is usually irreversible due to the strain induced under pressure. A reversible PIPT associated with a substantial bond rearrangement has been found in a metal–organic framework material, namely [tmenH₂][Er(HCOO)₄]₂ (tmenH₂²⁺=N,N,N′,N′‐tetramethylethylenediammonium). The transition is first‐order and is accompanied by a unit cell volume change of about 10 %. High‐pressure single‐crystal X‐ray diffraction studies reveal the complex bond rearrangement through the transition. The reversible nature of the transition is confirmed by means of independent nanoindentation measurements on single crystals.     

AB2‐type amphiphilic block copolymers composed of poly(ethylene glycol) and poly(N‐isopropylacrylamide) via single‐electron transfer living radical polymerization: Synthesis and characterization

Novel AB₂‐type amphiphilic block copolymers of poly(ethylene glycol) and poly(N‐isopropylacrylamide), PEG‐b‐(PNIPAM)₂, were successfully synthesized through single‐electron transfer living radical polymerization (SET‐LRP). A difunctional macroinitiator was prepared by esterification of 2,2‐dichloroacetyl chloride with poly(ethylene glycol) monomethyl ether (PEG). The copolymers were obtained via the SET‐LRP of N‐isopropylacrylamide (NIPAM) with CuCl/tris(2‐(dimethylamino)ethyl)amine (Me₆TREN) as catalytic system and DMF/H₂O (v/v = 3:1) mixture as solvent. The resulting copolymers were characterized by gel permeation chromatography and ¹H NMR. These block copolymers show controllable molecular weights and narrow molecular weight distributions (PDI < 1.15). Their phase transition temperatures and the corresponding enthalpy changes in aqueous solution were measured by differential scanning calorimetry. As a result, the phase transition temperature of PEG₄₄‐b‐(PNIPAM₅₅)₂ is similar to that in the case of PEG₄₄‐b‐PNIPAM₁₁₀; however, the corresponding enthalpy change is much lower, indicating the significant influence of the macromolecular architecture on the phase transition. This is the first study into the effect of macromolecular architecture on the phase transition using AB₂‐type amphiphilic block copolymer composed of PEG and PNIPAM. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4420–4427, 2009     

Synthesis,characterization, and evaluation of enzymatically degradable poly(N‐isopropylacrylamide‐co‐acrylic acid) hydrogels for colon‐specific drug delivery

The enzymatically degradable poly(N‐isopropylacrylamide‐co‐acrylic acid) hydrogels were prepared using 4,4^′‐bis(methacryloylamino)azobenzene (BMAAB) as the crosslinker. It was found that the incorporated N‐isopropylacrylamide (NIPAAm) monomer did not change the enzymatic degradation of hydrogel, but remarkably enhanced the loading of protein drug. The hydrogels exhibited a phase transition temperature between 4°C (refrigerator temperature) and 37°C (human body temperature). Bovine serum albumin (BSA) as a model drug was loaded into the hydrogels by soaking the gels in a pH 7.4 buffer solution at 4°C, where the hydrogel was in a swollen status. The high swelling of hydrogels at 4°C enhanced the loading of BSA (loading capability, ca. 144.5 mg BSA/g gel). The drug was released gradually in the pH 7.4 buffer solution at 37°C, where the hydrogel was in a shrunken state. In contrast, the enzymatic degradation of hydrogels resulted in complete release of BSA in pH 7.4 buffer solution containing the cecal suspension at 37°C (cumulative release: ca. 100 mg BSA/g gel after 4 days). Copyright © 2008 John Wiley & Sons, Ltd.     

Thermoresponsive conductivity of poly(N‐isopropylacrylamide)/potassium chloride gel electrolytes

A series of thermoresponsive polymer gel electrolytes (PGEs) based on poly(N‐isopropylacrylamide) in aqueous potassium chloride was synthesized by radiation‐induced polymerization and gelation using γ rays from a ⁶⁰Co source. The electric conductivity and swelling properties of the PGE were determined as a function of temperature. It was found that the electric conductivity of the PGE depended strongly on the swelling ratio; most notably, it changed drastically near the volume phase‐transition temperature of the PGE. The temperature/conductivity profile of the PGE exhibits a maximum peak at a certain temperature that is defined as the maximum conductivity temperature (T_max). The T_max of all of the PGEs prepared by low‐dose irradiation agreed with the temperature, near the end of the volume phase transition, where the PGE was completely shrunken. Consequently, the conductivity of gels should provide a good method with which the totally shrunken temperature of the thermoresponsive gels can be monitored with good temperature precision. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 134–141, 2002     

Selective Pre-concentration and Solid Phase Extraction of Mercury（Ⅱ） from Natural Water by Silica Gel-loaded （E）-N-（1-Thien-2＇-ylethylidene）-1,2-phenylenediamine Phase

Silica gel-loaded （E）-N-（1-thien-2＇-ylethylidene）-1,2-phenylenediamine （TEPDA） phase was synthesized based on physical adsorption approaches. The stability of a chemically modified TEPDA especially in concentrated hydrochloric acid that was then used as a recycling and preconcentration reagent allowed the further uses of silica gel-loaded immobilized TEPDA phase. The application of this silica gel-loaded phase to sorption of a series of metal ions was performed by using different controlling factors such as the pH of the metal ion solution and the equilibration shaking time by the static technique. This difference was interpreted on the basis of selectivity incorporated in these sulfur containing silica gel-loaded TEPDA phases. Hg（Ⅱ） was found to exhibit the highest affinity towards extraction by these silica gel-loaded TEPDA phases. The pronounced selectivity was also confirmed by the determined distribution coefficients （Kd） of all the metal ions, showing the highest value reported for mercury（Ⅱ） extraction by the silica gel immobilized TEPDA phase. The potential applications of the silica gel immobilized TEPDA phase to selective extraction of mercury（Ⅱ） from aqueous solution were successfully accomplished and preconcentration of low concentration of Hg（Ⅱ） （30 pg·mL^-1） from natural tap water with a preconcentration factor of 200 for Hg（Ⅱ） off-line analysis was conducted by cold vapor atomic absorption analysis.     

Phase‐transition characteristics of amphiphilic poly(2‐ethyl‐2‐oxazoline)/poly(ε‐caprolactone) block copolymers in aqueous solutions

Amphiphilic diblock and triblock copolymers of various block compositions based on hydrophilic poly(2‐ethyl‐2‐oxazoline) (PEtOz) and hydrophobic poly(ε‐caprolactone) were synthesized. The micelle formation of these block copolymers in aqueous media was confirmed by a fluorescence technique and dynamic light scattering. The critical micelle concentrations ranged from 35.5 to 4.6 mg/L for diblock copolymers and 4.7 to 9.0 mg/L for triblock copolymers, depending on the block composition. The phase‐transition behaviors of the block copolymers in concentrated aqueous solutions were investigated. When the temperature was increased, aqueous solutions of diblock and triblock copolymers exhibited gel–sol transition and precipitation, both of which were thermally reversible. The gel–sol transition‐ and precipitation temperatures were manipulated by adjustment of the block composition. As the hydrophobic portion of block copolymers became higher, a larger gel region was generated. In the presence of sodium chloride, the phase transitions were shifted to a lower temperature level. Sodium thiocyanate displaced the gel region and precipitation temperatures to a higher temperature level. The low molecular weight saccharides, such as glucose and maltose, contributed to the shift of phase‐transition temperatures to a lower temperature level, where glucose was more effective than maltose in lowering the gel–sol transition temperatures. The malonic acid that formed hydrogen bonds with the PEtOz shell of micelles was effective in lowering phase‐transition temperatures to 1.0M, above which concentration the block copolymer solutions formed complex precipitates. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2400–2408, 2000     

Chronological Change from Face‐On to Edge‐On Ordering of Zinc–Tetraphenylporphyrin at the Phenyloctane–Highly Oriented Pyrolytic Graphite Interface

The self‐assembled structure of alkoxy‐ and N‐alkylcarbamoyl‐substituted zinc–tetraphenylporphyrin at the liquid–highly oriented pyrolytic graphite (HOPG) interface was observed by using scanning tunneling microscopy. The alkoxy porphyrin showed a phase transition from face‐on to edge‐on ordering. The phase transition requires the close‐packed structure of alkoxy porphyrin. The chronological change of the ordering was traced to show the existence of several types of Ostwald ripening including two‐step phase transition from small edge‐on to face‐on and then further to edge‐on orderings. On the other hand, the N‐alkylcarbamoyl porphyrin showed persistent edge‐on ordering, and the ordering was analyzed by the Moiré pattern. Although the edge‐on ordering is observed only in the nonpolar solvent, the orderings have potential applications in the charge and energy transfer.     

Self‐assembly of star‐shaped polystyrene‐block‐polypeptide copolymers synthesized by the combination of atom transfer radical polymerization and ring‐opening living polymerization of α‐amino acid‐N‐carboxyanhydrides

The self‐assembling nature and phase‐transition behavior of a novel class of triarm, star‐shaped polymer–peptide block copolymers synthesized by the combination of atom transfer radical polymerization and living ring‐opening polymerization of α‐amino acid‐N‐carboxyanhydride are demonstrated. The two‐step synthesis strategy adopted here allows incorporating polypeptides into the usual synthetic polymers via an amido–amidate nickelacycle intermediate, which is used as the macroinitiator for the growth of poly(γ‐benzyl‐L ‐glutamate). The characterization data are reported from analyses using gel permeation chromatography and infrared, ¹H NMR, and ¹³C NMR spectroscopy. This synthetic scheme grants a facile way to prepare a wide range of polymer–peptide architectures with perfect microstructure control, preventing the formation of homopolypeptide contaminants. Studies regarding the supramolecular organization and phase‐transition behavior of this class of polymer‐block‐polypeptide copolymers have been accomplished with X‐ray diffraction, infrared spectroscopy, and thermal analyses. The conformational change of the peptide segment in the block copolymer has been investigated with variable‐temperature infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2774–2783, 2006     

Poly(N‐isopropylacrylamide)‐based comb‐type grafted hydrogel with rapid response to blood glucose concentration change at physiological temperature

A new type of glucose‐responsive hydrogel with rapid response to blood glucose concentration change at physiological temperature has been successfully developed. The polymeric hydrogel contains phenylboronic acid (PBA) groups as glucose sensors and thermo‐responsive poly (N‐isopropylacrylamide) (PNIPAM) groups as actuators. The response rate of the hydrogel to environmental glucose concentration change was significantly enhanced by introducing grafted poly(N‐isopropylacrylamide‐co‐3‐acrylamidophenylboronic acid) [poly(NIPAM‐co‐AAPBA)] side chains onto crosslinked poly(NIPAM‐co‐AAPBA) networks for the first time. The synthesized comb‐type grafted poly(NIPAM‐co‐AAPBA) hydrogels showed satisfactory equilibrium glucose‐responsive properties, and exhibited much faster response rate to glucose concentration change than normal type crosslinked poly(NIPAM‐co‐AAPBA) hydrogels at physiological temperature. Such glucose‐responsive hydrogels with rapid response rate are highly attractive in the fields of developing glucose‐responsive sensors and self‐regulated drug delivery systems. Copyright © 2008 John Wiley & Sons, Ltd.     

Temperature‐induced spontaneous sol–gel transitions of poly(D,L‐lactic acid‐co‐glycolic acid)‐b‐poly(ethylene glycol)‐b‐poly(D,L‐lactic acid‐co‐glycolic acid) triblock copolymers and their end‐capped derivatives in water

The spontaneous hydrogel formation of a sort of biocompatible and biodegradable amphiphilic block copolymer in water was observed, and the underlying gelling mechanism was assumed. A series of ABA‐type triblock copolymers [poly(D,L ‐lactic acid‐co‐glycolic acid)‐b‐poly(ethylene glycol)‐b‐poly(D,L ‐lactic acid‐co‐glycolic acid)] and different derivatives end‐capped by small alkyl groups were synthesized, and the aqueous phase behaviors of these samples were studied. The virgin triblock copolymers and most of the derivatives exhibited a temperature‐dependent reversible sol–gel transition in water. Both the poly(D,L ‐lactic acid‐co‐glycolic acid) length and end group were found to significantly tune the gel windows in the phase diagrams, but with different behaviors. The critical micelle concentrations were much lower than the associated critical gel concentrations, and an intact micellar structure remained after gelation. A combination of various measurement techniques confirmed that the sol–gel transition with an increase in the temperature was induced not simply via the self‐assembly of amphiphilic polymer chains but also via the further hydrophobic aggregation of micelles resulting in a micelle network due to a large‐scale self‐assembly. The coarsening of the micelle network was further suggested to account for the transition from a transparent gel to an opaque gel. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1122–1133, 2007     

Thermo‐ and pH‐induced phase transitions and network parameters of poly(N‐isopropylacrylamide‐ co‐2‐acrylamido‐2‐methyl‐propanosulfonic acid) hydrogels

Dual temperature‐ and pH‐sensitive hydrogels composed of N‐isopropylacrylamide (NIPAM) and 2‐acrylamido‐2‐methyl‐propanosulfonic acid (AMPS) were prepared by free‐radical crosslinking copolymerization in aqueous solution at 22 °C. The mole percent of AMPS in the comonomer feed was varied between 0.0 and 7.5, while the crosslinker ratio was fixed at 5.0/100. The effect of AMPS content on thermo‐ and pH‐ induced phase transitions as well as equilibrium swelling/deswelling, interior morphology and network structure was investigated. The volume phase transition temperature (VPT‐T) was determined by both swelling/deswelling measurements and differential scanning calorimetry (DSC) technique. In addition, the volume phase transition pH (VPT‐pH) was detected from the derivative of the curves of the swelling ratio (dQ_v/dpH) versus pH. The polymer‐solvent interaction parameter (χ) and the average molecular mass between crosslinks ( ) of hydrogels were calculated from swelling ratios in buffer solutions at various pHs. The enthalpy (ΔH) and entropy (ΔS) changes appearing in the χ parameter of hydrogels were also determined by using the modified Flory–Rehner equation. The negative values for ΔH and ΔS indicated that the hydrogels had a negative temperature‐sensitive property in water, that is, swelling at a lower temperature and shrinking at a higher temperature. It was observed that the experimental swelling data of hydrogels at different temperature agreed with the modified Flory‐Rehner approach based on the affine network model. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1713–1724, 2008     

Exothermic nonreversing process in the phase transition of poly(N‐isopropylacrylamide) studied with stochastic temperature‐modulated DSC

Exothermic nonreversing process is predicted to present in the phase transition of poly(N‐isopropylacrylamide) (PNIPAM). By employing TOPEM‐DSC, exothermic nonreversing heat flow peak is observed for the first time, and it usually appears under nonquasi‐static conditions. The exothermic nonreversing heat flow is proved to be from the formation of hydrogen bonds by the comparative studies on the phase transition of poly(N,N‐diethylacrylamide) (PDEAM) and cyclic heating and cooling of PDEAM and PNIPAM. Further TOPEM‐DSC studies on the phase transition of poly(NIPAM‐co‐DEAM) and poly(NIPAM‐co‐AAm) prove that hydrophobic force rather than hydrogen bonding is the main driving force for the phase transition, and hydrophobic force is also the driving force for the formation of inter‐ and intrachain hydrogen bonding. However, the phase transition driven by only hydrophobic force is a slow process. The combined action of hydrogen bonding and hydrophobic force makes the phase transition occur much faster. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1869–1877