钛－硅沸石的结构表征及其催化性能

ＸＲＤ，ＩＲ，２９ＳｉＭＡＳＮＭＲ，ＵＶ－ＶＩＳ及ＸＰＳ能谱表征证实钛原子进入了钛－硅五元环沸石的骨架晶格位（不含铝）．ＴＧ－ＤＴＡ结果表明，钛原子进入沸石骨架导致沸石骨架的热稳定性提高，超过１４７３Ｋ．氯丙烯与Ｈ２Ｏ２（３０％）的环氧化反应结果表明钛－硅沸石具有优异的氧化性能，这也从另一个侧面证实了钛原子位于沸石骨架晶格位．     

钛-硅沸石的结构表征及其催化性能

用ＸＲＤ，ＩＲ，＾２９ｓｉＭＡＳＮＭＲ，ＵＶ－ＶＩＳ及ＸＰＳ能谱表征证实钛原子进入了钛－硅五元环沸石的骨加格位（不含铝）。ＴＧ－ＤＴＡ结果表明，钛原子进入沸石骨架导致沸石骨架的热稳定性提高，超过１４７３Ｋ。氯丙烯与Ｈ２Ｏ２（３０％）的环氧化反应结果表明钛－硅沸石具有优异的氧化性能，这也从另一个侧证实了钛原子位于沸石骨架晶格位。     

Ti─Si沸石的催化氧化性能 Ⅰ．烯烃的氧化及骨架钛的作用

详细研究了Ｔｉ─Ｓｉ沸石在Ｈ_２Ｏ_２存在下对氯丙烯的环氧化、苯乙烯的氧化和环己烯的氧化等反应的催化作用．发现上述三种结构的烯烃其主要定向产物并不一致：氯丙烯氧化产物主要为环氧氯丙烷，苯乙烯氧化主要产物为苯乙醛、环己烯氧化主要产物为环己二酮．说明烯烃氧化的主要定向产物的结构依赖于有机底物的结构，并不全都给出环氧产物．在三个反应中，Ｔｉ─Ｓｉ沸石均表现出显著的催化活性，这可能与沸石骨架中钛的存在有关．发现在氯丙烯环氧化反应中，只有ＴＳ－１及ＴＳ－２表现出环氧化活性．推测沸石骨架位中存在的钛在氧化反应中起重要作用．     

TS—1沸石的合成,结构及催化性能探讨

讨论了用两种不同硅源合成钛硅沸石ＴＳ－１的方法和合成过程中应注意的问题，并通过ＸＲＤ、ＩＲ、ＴＥＭ和ＳＳＡ等手段对沸石的结构及热稳定性进行了表征和研究，确认了钛已进入沸石骨架，初步探讨了ＴＳ－１沸石合成时ＴＰＡ离子的模板作用机理，此外，通过在温和条件下用Ｈ２Ｏ２选择性氧化正己烷的反应，考察了ＴＳ－１沸石的催化活性，得到了比较满意的结果。     

新型两亲性含钛β沸石的制备与表征

将Ti-β沸石经过正十八烷基三氯硅烷改性制得两亲性含钛β沸石，并通过 XRD，FT-IR，UV-vis和N_2吸附-脱附等手段对其进行了表征。同改性前样品相比， 制备出的两亲性含钛β沸石保持了原来的晶体结构，其BET比表面积和BJH孔容均稍 有下降。FT-IR和UV-vis结果说明该沸石骨架在存在四配位钛，从而有可能成为催 化烯烃环氧化反应的活性中心。由于外表面阔别分覆盖有憎水性的硅烷基团而其它 部分吃不开现亲水性，该两亲性含钛沸石分布于水/油两相界面处，因此该催化剂 可以应用于不添加共溶剂 的相界面催化反应。     

TS－1沸石的合成、结构及催化性能探讨

讨论了用两种不同硅源合成钛硅佛ＴＳ－１的方法和合成过程中应注意的问题，并通过ＸＲＤ、ＩＲ、ＴＥＭ和ＳＳＡ等手段对沸石的结构及热稳定性进行了表征和研究，确认了钛已进入沸石骨架。初步探讨了ＴＳ－１沸石合成时ＴＰＡ￣＋离子的模板作用机理。此外，通过在温和条件下用Ｈ＿２Ｏ＿２选择性氧化正已烷的反应，考察了ＴＳ－１沸石的催化活性，得到了比较满意的结果。     

两亲性TS-1沸石的制备及其相界面催化反应性能的研究

采用三甲基氯硅烷和正十八烷基三氯硅烷对TS-1沸石样品进行表面修饰，制备出了两亲性含钛沸石样品．这类两亲性含钛沸石能分布于水、油两相界面处．改性后样品的骨架未遭破坏，其中钛仍然保持了四配位骨架钛的状态，但其晶貌发生了某些改变．这类两亲性样品在不加共溶剂及静置的反应条件下，对1-辛烯和双氧水的相界面环氧化催化反应表现出优良的催化活性．尤其是三甲基氯硅烷改性后的TS-1沸石，在相界面催化反应中，具有比改性前高得多的活性．我们还发现，在该相界面催化反应条件中，相界面的面积和催化剂用量是两个最重要的影响因素，当相界面面积(cm^2)与催化剂用量(mg)的比例控制在0．15左右时，两亲性TS-1沸石的催化活性达到最高值．     

不同结构母体对制备钛沸石的影响

以ＺＳＭ－５，ＺＳＭ－１１，β，Ｙ，ＺＳＭ－１２和ＺＳＭ－４８型沸石为体进行气固相同晶取代，考察了母 体对钛进入沸石骨架难易程度的影响。结果表明，以ＺＳＭ－５，ＺＳＭ－１１和β型沸石为母体，钛较易进入沸石骨架，而以Ｙ，ＺＳＭ－１２和ＺＳＭ－４８型沸石为母体，钛很难进入沸石骨架。     

邻对苯二酚的合成方法

用自制的钛硅沸石ＴＳ－１为催化剂，对Ｈ２Ｏ２存在下苯酚直接羟基化合成邻、对苯二酚的反应条件，主要影响因素及机理进行了探讨，发现该民传统的合成方法相比，反应的选择性及转化率较高，工艺简单，成本低和污染少。     

杂原子B—ZSM—35沸石的干法合成,表征及CO＋H2反应性能的研究

首次利用吸附态模板剂在Ｎａ２Ｏ－ＳｉＯ２－Ｂ２Ｏ３－ＤＥＡ干粉体系中合成了杂原子Ｂ－ＳＺＭ－３５沸石，ＸＲＤ，ＳＥＭ，ＩＲ，及ＣＯ加氢反应研究了其物理化学特性。结果表明，Ｂ原子同晶取代Ａｌ原子进入ＺＳＭ－３５沸石骨加。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.