钛基纳米多孔金电极对甲醛氧化的电催化活性

采用水热法制备了钛基纳米金微粒修饰电极(Au/Ti)。扫描电镜图表明纳米金颗粒粒径大约为300 nm,在钛基体表面构成三维多孔网状结构。运用循环伏安,电位阶跃和交流阻抗等电化学技术研究了碱性介质中甲醛在Au/Ti电极上的电氧化行为。循环伏安图显示,甲醛在Au/Ti上的起始氧化电位在-0.90 V左右,相对于多晶金电极提前大约0.2 V,交流阻抗测试表明,甲醛在Au/Ti电极上电氧化表现出低的电荷传递电阻。研究结果表明钛基纳米金微粒修饰电极对甲醛氧化具有良好的电催化活性。     

间接电氧化法合成甘油醛

通过电化学合成前驱体和溶胶-凝胶法在Ti表面修饰一层纳米TiO2膜,在纳米Ti02膜上电沉积分散的Pt微粒制成钛基纳米TiO2-Pt(Ti/nano-TiO2-pt)修饰电极。采用循环伏安法、间接电氧化法研究了纳米Ti02-Pt修饰电极的电催化活性以及Mn^3 ／Mn^2 媒质氧化甘油为甘油醛的过程。结果表明,纳米Ti02-Pt修饰电极对Mn^2 的电氧化具有高催化活性,电流效率可达90％以上,非均相电解得到的Mn^3 可一步氧化甘油为甘油醛,收率为91％。     

新型的钛基Ni-Sn/Ti电极的制备及对甲醇氧化反应的电催化活性

利用电热法,一步制备出新型的钛基Ni-Sn/Ti电极(Ni8Sn/Ti, Ni7Sn3/Ti 和 Ni/Ti)。扫描电镜（SEM）图像表明,催化剂以片状的纳米颗粒形式沉积于钛基体上。利用电化学伏安技术、电位阶跃法和电化学交流阻抗谱（EIS）,研究了这些电极在1mol.L�1NaOH溶液中对甲醇氧化反应的电催化活性。研究表明,与Ni7Sn3/Ti,Ni/Ti以及多晶镍电极相比,Ni8Sn/Ti电极对甲醇氧化反应表现出更高的阳极氧化电流和更低的起始电位。EIS分析表明,在本文所考察的阳极电位和甲醇浓度下,Ni8Sn/Ti电极对甲醇氧化反应显示出极低的电荷传递电阻。结果表明,这种新型的钛基Ni8Sn/Ti电极对甲醇氧化反应具有极高的电催化活性。     

一种无膜的自呼吸式直接醇燃料电池

采用液相化学还原法制备出多壁碳纳米管（MWCNT）负载的双金属PdNi纳米颗粒（PdNi／MWCNT）;采用水热法,在乙醇为溶剂和还原剂的体系中,制备出MWCNT负载的双金属AgCo纳米颗粒（AgCo／MWCNT）．碱性溶液中,PdNi／MWCNT对甲醇、乙醇、丙醇和丁醇的氧化具有稳定而强的电催化活性;AgCo／MWCNT对氧还原反应也表现出强的电活性,且对上述高浓度的醇具有较强的耐受力．以PdNi／MWCNT催化剂为阳极,同时将AgCo／MWCNT催化剂制备成气体扩散电极,组装成无离子交换膜的自呼吸式直接醇燃料电池．分别以甲醇、乙醇、丙醇和丁醇为燃料时,这种无膜的燃料电池均能稳定放电,且具有较高的功率密度及较大的输出电压．     

碳纳米管上原位沉积钯-钴-镍纳米颗粒及其对乙醇氧化的电活性

以水合肼为还原剂,在水和乙醇的混合溶液中制备多壁碳纳米管(MWCNT)负载的纳米镍(Ni/MWCNT)和纳米镍钴(Ni-Co/MWCNT)颗粒,然后将它们分别与氯化钯溶液反应,形成的钯纳米颗粒原位沉积在MWCNT表面,从而得到MWCNT负载的PdNi/MWCNT和Pd-Ni-Co/MWCNT催化剂。SEM和TEM图像显示,MWCNT上的催化剂颗粒是由5~10 nm的小颗粒团聚而成的30~100 nm的大颗粒,三金属催化剂的粒径比双金属的粒径小,在MWCNT上的分散度更高。ICP和EDS分析显示,Pd直接还原并包覆在纳米镍和纳米镍钴表面;采用循环伏安和计时电流技术,研究了催化剂在碱性溶液中对乙醇氧化的电催化活性,结果表明,Pd-Ni-Co/MWCNT催化剂对乙醇氧化具有强的电催化活性,乙醇氧化对应的峰电流密度达101.8 m A·cm~(-2),并且催化剂催化活性稳定。     

乙二醛在Ti/纳米TiO2-Pt修饰电极上的电催化氧化

采用溶胶-凝胶和电沉积法制备Ti基纳米TiO2-Pt(Ti/纳米TiO2-Pt)修饰电极. X射线衍射(XRD)表明纳米TiO2为锐钛矿型, 扫描电镜(SEM)显示Pt纳米粒子在纳米TiO2多孔膜的表面呈现簇分散状态, 平均粒径约25 nm. 通过循环伏安(CV)和计时电流法研究了Ti/纳米TiO2-Pt修饰电极对乙二醛直接电氧化的电催化活性, 结果表明, 修饰电极对乙二醛的直接电氧化呈现良好的催化活性, 在0.60和1.23 V(vs SCE)出现两个氧化峰, 二者电流密度分别为16 和42 mA·cm-2, 约为纯Pt电极的2倍和1.5倍, 反应过程受浓差扩散控制.     

甲醇在铂修饰的氧化钛电极上电催化氧化行为的研究

运用电化学方法评价了电化学阴极还原-阳极氧化两步法制得的以钛为基体的铂修饰的钛氧化物(Pt-TiO_x/Ti)电极对甲醇电催化氧化的性能,结果表明,制得的修饰电极对甲醇氧化呈现了很高的电催化活性和好的稳定性.通过X光电子能谱(XPS)、扫描隧道显微镜(STM)和现场傅立叶变换红外(FTIR)反射光谱等技术,发现修饰电极对甲醇氧化具有高的电催化性能,可归属于纳米级Pt粒子在TiO_x中的高度分散及由于Pt和TiO_x的相互作用,使电极表面对甲醇氧化中间产物CO的吸附量大大降低.     

纳米钯催化剂对甲醇的电催化氧化

采用水热法,以甲醛作还原剂还原Pd2+-EDTA络合物,制得钛基纳米钯颗粒电极(nanoPd/Ti).扫描电子显微镜(SEM)显示,纳米钯颗粒直径约为60 nm,形成三维立体网状结构.在碱性溶液中,循环伏安及交流阻抗测试分别表明:nanoPd/Ti电极对甲醇氧化有极高的阳极电流、较低的起始氧化电位和较强的抗CO毒化能力.在nanoPd/Ti电极上甲醇电氧化反应的阻抗值较低,增加甲醇浓度,电极阻抗更低.电极对甲醇氧化具有极好的电催化活性.     

碳纳米管上原位沉积钯-钴-镍纳米颗粒及其对乙醇氧化的电活性

以水合肼为还原剂,在水和乙醇的混合溶液中制备多壁碳纳米管(MWCNT)负载的纳米镍(Ni/MWCNT)和纳米镍钴(Ni-Co/MWCNT)颗粒,然后将它们分别与氯化钯溶液反应,形成的钯纳米颗粒原位沉积在MWCNT表面,从而得到MWCNT负载的Pd-Ni/MWCNT和Pd-Ni-Co/MWCNT催化剂。SEM和TEM图像显示,MWCNT上的催化剂颗粒是由5~10 nm的小颗粒团聚而成的30~100 nm的大颗粒,三金属催化剂的粒径比双金属的粒径小,在MWCNT上的分散度更高。ICP和EDS分析显示,Pd直接还原并包覆在纳米镍和纳米镍钴表面;采用循环伏安和计时电流技术,研究了催化剂在碱性溶液中对乙醇氧化的电催化活性,结果表明,Pd-Ni-Co/MWCNT催化剂对乙醇氧化具有强的电催化活性,乙醇氧化对应的峰电流密度达101.8 mA·cm^-2,并且催化剂催化活性稳定。     

铅修饰纳米多孔铂催化剂对甲酸氧化的电活性（英文）

用合适金属修饰的铂催化剂能够显著增强其对甲酸氧化的电活性.本文以水热法制备了钛负载的纳米多孔铂电极(nanoPt/Ti),然后采用循环伏安法,通过扫描不同的周数(n),用适量的铅对nanoPt/Ti电极进行修饰,得到一种新型的铅修饰的纳米多孔铂电极(nano Pb_((n))-Pt/Ti).采用循环伏安(CV)、计时电流和计时电位法研究其对对甲酸氧化的电活性.CV结果显示nanoPt/Ti和nanoPb_((n))-Pt/Ti电极对甲酸氧化表现出较高的催化活性,并且nanoPb_((20))-Pt/Ti电极对甲酸氧化的起始电位为-0.06 V,相比nanoPt/Ti电极的起始电位(0.06 V),明显有所负移.此外,nanoPb_((20))-Pt/Ti电极的第一个氧化峰电流密度为12.7 mA·cm~(-2),远远大于nanoPt电极(4.4 mA·cm~(-2));计时电流显示在电位为0.1 V时,在0.5 mol·L~(-1)H_2SO_4+1 mol·L~(-1 )HCOOH溶液中,nanoPb_((20))-Pt/Ti电极达到稳定时的电流为8.09 mA·cm~(-2),是nanoPt电极的60倍,表明铅修饰的nanoPt/Ti对甲酸氧化的电活性急剧增加;在1.5mA、2 mA、2.2 mA和2.5 mA下的计时电位结果表明,nanoPb_((20))-Pt/Ti电极上甲酸氧化过程表现出显著的电化学振荡,且和nano Pt/Ti电极相比,振荡现象能持续更长的时间,说明nanoPb_((20))-Pt/Ti电极具有更强的表面抗毒化能力.     

High Performance Pd,PdNi, PdSn and PdSnNi Nanocatalysts Supported on Carbon Nanotubes for Electrooxidation of C2C4 Alcohols

Nanocatalysts Pd, Pd₈Ni₂, Pd₈Sn₂ and Pd₈Sn₁Ni₁ supported on multi‐walled carbon nanotubes (MWCNTs) were successively synthesized by the chemical reduction method in the glycol‐water mixture solvent. Transmission electron microscopy results show that the prepared Pd, Pd₈Ni₂, Pd₈Sn₂ and Pd₈Sn₁Ni₁ nanoparticles are uniformly dispersed on the surface of MWCNTs. The average particle sizes of the nanocatalysts are 3.5–3.8 nm. Electroactivity of the prepared catalysts towards oxidation of ethanol, 1‐propanol, 2‐propanol, n‐butanol, iso‐butanol and sec‐butanol (C2? C4 alcohols) in alkaline medium was studied by cyclic voltammetry and chronoamperometry. The current density obtained for the electrooxidation of C2? C4 alcohols depends on the catalysts and the various structures of the alcohols. Addition of Sn or/and Ni to Pd nanoparticles enhances the electroactivity of the Pd/MWCNT catalyst. Furthermore, the ternary Pd₈Sn₁Ni₁/MWCNT catalyst presents the highest electroactivity for the oxidation of C2? C4 alcohols among the prepared catalysts. Electrocatalytic activity order among propanol isomers and butanol isomers is as follows respectively: 1‐propanol > 2‐propanol, and n‐butanol > iso‐butanol > sec‐butanol > tert‐butanol. This is consistent with the Mulliken charge value of the carbon atom bonded with hydroxyl group in the corresponding alcohol molecule.     

树枝状纳米银颗粒的制备与电活性

在Ag(NH3)2+溶液中,在钛基体上电沉积出树枝状纳米银颗粒,研究了沉积电位对树枝状纳米银颗粒形成的影响,探讨了这种树枝状纳米银颗粒形成的机理,并研究了这种钛基树枝状纳米银电极(Ag/Ti)在碱性溶液中对甲醛氧化的电催化活性。结果表明,在30 mmol/LAg(NH3)2+以及沉积电位在-1.8～-1.2 V(vsAg)时,形成了形态为树枝状的纳米银颗粒。在沉积电位为-1.6 V(vs Ag),Ag(NH3)2+浓度为30 mmol/L的溶液中,电沉积制备的这种树枝状纳米银电极(Ag/Ti)对甲醛氧化具有强的电催化活性。循环伏安曲线表明,在0.1 mol/LNaOH溶液中以及甲醛的浓度范围在0～40 mmol/L,甲醛浓度和它的氧化峰电流密度呈现良好的线性关系,检测下限达到0.662 mmol/L,这种新型的树枝状纳米银电极有望作为甲醛检测的传感器。     

Electrodeposition and electrocatalytic properties of platinum nanoparticles on multi-walled carbon nanotubes: effect of the deposition conditions

Platinum (Pt) nanoparticles were electrochemically deposited on multi-walled carbon nanotubes (MWCNTs) through a three-step process, including an electrochemical treatment of MWCNT, electro-oxidation of PtCl₄ ²⁻ to Pt(IV) complex, and an electro-conversion of Pt(0) on MWCNT. The effect of formation conditions for Pt(IV) complexes on the Pt nanoparticals transformed was investigated. The structure and elemental composition of the resulting Pt/MWCNT electrode were characterized by transmission electron micrograph (TEM) and energy dispersive X-ray spectroscopy (EDX). The electrocatalytic properties of the resulting Pt/MWCNT electrode for methanol oxidation have been investigated. The high electrocatalytic activity and good stability of Pt/MWCNT electrode may be attributed to the high dispersion of platinum nanoparticles and the particular properties of the MWCNT supports.     

Effect of the iridium oxide thin film on the electrochemical activity of platinum nanoparticles

The influence of the iridium oxide thin film on the electrocatalytic properties of platinum nanoparticles was investigated using the electro-oxidation of methanol and CO as a probe. The presence of the IrO(2) thin film leads to the homogeneous dispersion of Pt nanoparticles. For comparison, polycrystalline platinum and Pt nanoparticles dispersed on a Ti substrate in the absence of an IrO(2) layer (Ti/Pt) were also investigated in this study. Inverted and enhanced CO bipolar peaks were observed using an in situ electrochemical Fourier transform infrared technique during the methanol oxidation on the Pt nanoparticles dispersed on a Ti substrate. Electrochemical impedance studies showed that the charge transfer resistance was significantly lower for the Ti/IrO(2)/Pt electrode compared with that of the massive Pt and Ti/Pt nanoparticles. The presence of the IrO(2) thin film not only greatly increases the active surface area but also promotes CO oxidation at a much lower electrode potential, thus, significantly enhancing the electrocatalytic activity of Pt nanoparticles toward methanol electro-oxidation.     

Co3O4/Ti电催化膜电极制备及其苯甲醇催化氧化性能

本文采用浸渍涂覆法成功制备出多孔Ti负载纳米Co₃O₄电催化膜电极（Co₃O₄/Ti）,以该膜电极为阳极,辅助电极为阴极,构建电催化膜反应器（electrocatalytic membrane reactor,ECMR）用于可控催化氧化苯甲醇制备苯甲醛和苯甲酸,并考察了 Co₃O₄/Ti 膜电极结构、电化学性能以及ECMR不同操作参数对苯甲醇转化率、苯甲醛和苯甲酸选择性的影响. 结果表明,负载Co₃O₄纳米颗粒可以显著提高Ti膜电极的电化学性能和催化活性. 在常温常压下,当反应物苯甲醇浓度为10 mmol·L^-1,pH为7.0,停留时间为5.0 min,电流密度为2.5 mA·cm^-2,苯甲醇的转化率达到49.8%,苯甲醛选择性为51.5%,苯甲酸选择性为23.6%.     

Electrooxidation of 2-propanol on Pt, Pd and Au in alkaline medium

Pd and Au are investigated as electrocatalysts for 2-propanol oxidation and compared with the conventional catalyst of Pt in alkaline medium. The current density for 2-propanol oxidation on Pd electrode is much higher than that on Pt electrode. The onset potential for 2-propanol oxidation on Pd electrode is more negative compared with that on Pt electrode. The results show that Pd is a good electrocatalyst for 2-propanol oxidation and the activity for the electrooxidation of 2-propanol is higher than Pt and Au in alkaline medium. Pd has higher electrocatalytic activity and better stability for the electrooxidation of 2-propanol. The present study shows a promising choice of Pd as effective electrocatalyst for 2-propanol electrooxidation in alkaline medium.     

球型Pt微粒电极的构建及其对甲醇电氧化的研究

以镍铬合金为基体,在其表面电化学沉积制备了Pt微粒电极,用扫描电子显微镜（SEM）对电极的表面形貌进行了表征,电化学方法考察了电极的电化学性能和甲醇在该电极上的电催化行为．结果表明镍铬合金表面沉积的球型Pt微粒电极对甲醇的电氧化具有良好的催化活性,相同实验条件下,该电极的催化活性比纯Pt电极高30倍．该电极对甲醇的电氧化显示出较高的催化性能．