基于Pancharatnam-Berry相位调控产生贝塞尔光束

提出了一种基于Pancharatnam-Berry相位设计制作的超表面平面轴棱锥透镜产生贝塞尔光束的方法.理论分析表明:由于Pancharatnam-Berry相位的自旋相关性,设计的平面轴棱锥透镜需采用左旋圆偏振光入射才能有效地产生贝塞尔光束.超表面微结构单元的旋转率与最大无衍射距离成反比,这提供了一个获得更大无衍射距离的方便的途径.最后,搭建了一套基于平面轴棱锥透镜的贝塞尔光束产生系统,实验结果与数值模拟结果一致.这些结论有助于设计制作更多新颖的基于Pancharatnam-Berry相位的平面光子学器件.     

高功率蓝光半导体激光加工光源EI北大核心CSCD

针对目前铜、金等金属材料加工的实际应用需求,开展了连续输出功率500 W的光纤耦合输出蓝光半导体激光加工光源研究。基于平面窗口TO封装的蓝光半导体激光单管器件,设计采用长后工作距的快轴准直镜和慢轴准直镜分别准直,获得低发散角、高光束质量的单元准直光束;结合二维空间合束、偏振合束和光纤耦合,将144个蓝光单管器件耦合进200μm/NA 0.22光纤,通过ZEMAX软件对半导体激光光路进行光线追踪模拟;并从实验上实现,3 A电流驱动下,200μm/NA 0.22光纤输出连续功率523 W,电光转换效率29%。该激光光源具有直接加工铜、金等材料的能力。     

高能光纤激光经准直系统后的光束质量研究

应用光线光学的理论,对透镜的几何像差、热非线性等因素对光纤激光光束质量的影响进行了分析和计算,给出了激光通过多透镜光学系统后,光束质量参数M²与系统参数的一般关系. 研究了高能光纤激光通过准直系统后的光束质量. 研究结果表明,随着激光功率的增大,经准直系统后光束的光束质量存在最佳值,其对应的激光功率与准直系统参数有关,为高能光纤激光准直系统的设计提供了参考. 关键词： 高能光纤激光 光束质量 准直系统 光线光学     

高功率高效率光纤耦合半导体激光模块研制

采用光束整形和空间合束的方法,研制出高功率、高效率多阵列光纤耦合半导体激光模块。将波长为976nm连续工作的5个标准半导体阵列,通过对快轴进行准直和快慢轴光束旋转的方式进行光束整形,准直后进行空间合束,经耦合透镜聚焦,耦合入芯径400μm、数值孔径0.22的光纤。测量结果显示:光纤的出光功率最大可达到327 W,光纤耦合效率大于93.6%。     

全光纤多种子激光脉冲产生系统

报道一种可精确同步输出宽带啁啾脉冲、纳秒级整形脉冲以及窄带光参量啁啾放大抽运脉冲的全光纤多种子激光脉冲产生系统.采用掺镱光纤锁模激光器和掺镱单纵模光纤振荡器作为系统的光源,将掺镱光纤锁模激光器输出的超短脉冲分束啁啾展宽至0.9ns后,一路进行放大产生10μJ量级的宽带啁啾脉冲为高能拍瓦激光器系统提供种子光脉冲,另一路通过1.2nm滤波产生140ps的基元脉冲,通过光纤堆积器产生可编程整形的2.3ns脉冲,再经过放大达到10μJ量级,提供任意整形的压缩脉冲.同时,将部分掺镱光纤锁模激光器输出的超短脉冲进行光电转换并锁相后,产生与锁模超短脉冲高精度同步的电脉冲用于触发幅度调制器,将掺镱单纵模光纤振荡器输出的连续光削波放大,产生光参量啁啾放大抽运脉冲.该系统能够根据物理实验的需要,非常灵活地在输出各种脉冲之间做出选择.     

一种产生无衍射贝塞尔光束的新型组合锥透镜

提出一种可产生无衍射贝塞尔(Bessel)光束的新型光学元件——组合锥透镜,由正、负轴棱锥胶合在一起设计而成。其变换光束特性与单个正轴棱锥相同,等效底角由正、负轴棱锥底角之差决定,因此可通过较大底角的正、负轴棱锥组合得到更小角度的底角,以获得更长距离的无衍射光,解决了单个正轴棱锥小角度加工困难的技术问题。推导出组合锥透镜的ABCD传输矩阵,数值模拟平面波通过组合锥透镜后的光场为无衍射Bessel光束,并从几何光学角度用Zemax软件模拟组合锥透镜后的光场分布,与正轴棱锥后的光场进行了比较。研究结果为实现无衍射Bessel光束开辟一条新的途径。     

大气激光通信用直锥形光纤发射天线

 提出采用直锥形光纤作为大气激光通信的发射天线,将多模光纤输出的部分相干发散光束变换为准平行光束的方案,既能得到发散角很小的部分相干激光光束,又能保证激光器输出能量的完全传输。采用光线追迹法分析了任意光束从锥形光纤小端面输入、大端面输出的发散角。结果表明,当直锥形光纤长度大于某一特定值时,从小端面输入的入射角小于数值孔径角的所有光线理论上都可以变换为出射角度小于光纤半锥角的光线,因此直锥形光纤可以作为部分相干光源的准直透镜,代替传统的凸透镜,用于改善光束的发散角。对远场光斑进行了数值模拟和实验研究,结果显示：直锥形光纤透镜对朗伯光源的准直光束比传统凸透镜的准直光束发散角小,光斑半径小且均匀性好,证明用此方法可以得到低发散、低空间相干性的光斑。     

高功率叠阵二极管激光器光束整形

采用光线追迹法详细分析线阵二极管激光器经微球面柱透镜快轴准直后的光强变化情况,利用快轴准直微球面柱透镜的球差可调整输出激光光强分布的特性,得出了快轴准直输出发散角约5°时光强分布具有较好的平顶形式。根据叠阵二极管激光器输出光的特点,设计了由25个二极管激光器组成的叠阵二极管激光器的光束整形输出系统,该系统由快轴准直微透镜、快轴耦合透镜和慢轴耦合透镜组成,把需要泵浦的激光介质薄片设计在快轴耦合透镜的焦点上,并且在慢轴耦合透镜的成像面附近,得到了7mm×8mm的泵浦光斑,光强不均匀性约10%,输出效率达到85%。     

柱透镜和弯月透镜实现半导体激光器光束整形

针对半导体激光器的发光特点,设计了半导体激光器的光束整形系统。首先采用柱透镜准直和偏转沿Y轴发散的光束;然后再采用望远系统对X轴发散的光束进行准直和扩束;最后采用弯月透镜对发射光束压缩,实现半导体激光器的光束整形,降低光束发散角,提高光束质量。利用ZEMAX软件模拟系统,结果表明,整形后输出光束沿X轴和Y轴的发散角变为4.922mrad,输出光斑直径为1.2707mm,整形系统总长度为65.6618mm,各元件的最大直径为20.52mm,输出光束质量和系统结构都优于同类产品。     

基于少模光纤被动调Q柱矢量光光纤激光器

通过单模光纤和少模光纤熔融拉锥耦合的方法制备出模式转换器,而后将一层多壁的碳纳米管薄膜作为可饱和吸收体覆盖到拉锥光纤的锥区,形成一种可饱和吸收体柱矢量光器件.结合调Q光纤激光器和模式转换器件的优势,可以简单高效地产生脉冲柱矢量光束,并得到具有峰值功率高、模式纯度高等特点的脉冲高阶模式激光输出.通过实验实现了中心波长为1560nm、最大单脉冲能量和最大峰值功率分别为116nJ和57mW的稳定调Q脉冲输出.通过调节光路中的偏振控制器,可以分别实现径向和角向偏振的调Q脉冲激光的输出.     

135 W average-power femtosecond pulses at 520 nm from a frequency-doubled fiber laser system

We present a high-average-power femtosecond laser system at 520 nm central wavelength. The laser system delivers sub-500 fs pulses with 135 W average power at a pulse repetition rate of 5.25 MHz. Excellent beam quality is provided by high power fiber amplifiers and maintained during frequency doubling, resulting in a beam quality factor of M2<1.2. To our knowledge, the system presented here is the highest average power green laser source generating femtosecond pulses with diffraction-limited beam quality.     

用于激光聚变驱动器的全光纤、全固化光脉冲产生系统

报道一种全固化、全光纤的用于高功率激光驱动的惯性约束聚变驱动器的光脉冲产生系统,采用单纵模振荡器输出连续激光信号,经过相位调制器和振幅调制器,得到一个时间波形上已整形且具有一定带宽(约0.1 nm)的激光脉冲,经光纤放大器放大并经光纤分束器分束后同时输出四路激光脉冲,各路激光脉冲先通过时间同步调整单元精确控制时间同步关系后,经可编程光纤衰减器调节各路之间的功率平衡后再通过光纤放大器做进一步放大并通过150 m光纤传输输出至预放系统.该光纤系统可输出0.3—20 ns、带宽0.1 nm、能量数纳焦的几乎任意 关键词： 激光聚变驱动器 前端 光纤激光系统     

Millijoule pulse energy high repetition rate femtosecond fiber chirped-pulse amplification system

We report on an ytterbium-doped fiber chirped-pulse amplification (CPA) system delivering millijoule level pulse energy at repetition rates above 100 kHz corresponding to an average power of more than 100 W. The compressed pulses are as short as 800 fs. As the main amplifier, an 80 microm core diameter short length photonic crystal fiber is employed, which allows the generation of pulse energies up to 1.45 mJ with a B-integral as low as 7 at a stretched pulse duration of 2 ns. A stretcher-compressor unit consisting of dielectric diffraction gratings is capable of handling the average power without beam and pulse quality distortions. To our knowledge, we present the highest pulse energy ever extracted from fiber based femtosecond laser systems, and a nearly 2 orders of magnitude higher repetition rate than in previously published millijoule-level fiber CPA systems.     

自由耦合输出的大模场面积光子晶体光纤锁模激光器

对一种基于高增益掺Yb³⁺大模场面积光子晶体光纤（PCF）的锁模激光器进行了简化线型腔结构的实验和理论研究.实验中直接使用塌陷打磨为0°角的光纤端面作为一端腔镜,利用其端面反馈获得了激光振荡,并进一步利用半导体可饱和吸收镜（SESAM）和光栅对的滤波作用实现了稳定的锁模运转.通过调节滤波程度,使激光器实现了从宽带滤波锁模到窄带滤波锁模的连续可调谐.在宽带滤波锁模的条件下,得到了最大平均输出功率2.2 W,单脉冲能量29.3 nJ,脉冲宽度367 fs的锁模脉冲输出;在窄带滤波锁模的条 关键词： 飞秒激光 光纤激光器 光子晶体光纤 大模场面积光纤     

不同波形脉冲激光的时域误差对相干合成的影响

相干合成技术是实现高功率、高亮度光纤激光系统的重要技术途径.然而, 脉冲激光阵列中常常存在时域误差,这将影响脉冲激光的相干合成效果. 建立了脉冲激光存在时域误差时的相干合成理论模型,并在不同波形(方波、三角波、正弦波) 的脉冲激光存在时域误差时,对相干合成光束在远场的脉冲波形、峰值功率、 光强分布和桶中功率(PIB)等特性进行了数值计算和对比分析.计算结果表明: 方波脉冲激光相干合成光束的脉冲波形受时域误差影响严重,光强分布和PIB随着时域误差 的增大发生线性变化;三角波脉冲激光相干合成光束的脉冲波形和峰值功率受时域误差 影响严重,光强分布和PIB在时域误差较大时随着时域误差的增大发生较为剧烈的变化; 正弦波脉冲激光相干合成光束具有较好的输出特性,在两路正弦波脉冲激光相干合成中, 将两脉冲之间的时延控制在脉冲持续时间的10%以内,就能取得良好的合成效果.     

High-peak-power femtosecond pulse compression with polarization-maintaining ytterbium-doped fiber amplification

We report the generation of 140 fs pulses with a peak power of up to 270 kW using a fiber pulse source based on a polarization-maintaining ytterbium-doped fiber amplifier and a semiconductor saturable absorber mirror mode-locked fiber laser seed. The seed laser pulses were amplified and chirped in the fiber amplifier and subsequently compressed in an external transmission grating pair. The use of a polarization-maintaining amplifier addresses nonlinear polarization-induced limitations to the obtainable compressed pulse duration and quality that can arise if isotropic fiber amplification is used. Numerical simulations of the system support the experimental measurements and also confirm the role of fiber dispersion in obtaining high-quality compressed pulses.     

基于非线性偏振旋转锁模的高功率光子晶体光纤飞秒激光振荡器

为了探索大模场面积光子晶体光纤锁模激光器在全正色散锁模域内的耗散孤子锁模机理, 以获得更大的单脉冲能量和更高的峰值功率, 本文搭建了以掺镱大模场面积光子晶体光纤作为增益介质的耗散孤子锁模激光器. 激光器使用环形腔结构, 利用非线性偏振旋转以及滤光片提供的耗散作用实现了稳定的锁模运转. 实验中, 从激光器振荡级直接获得了平均功率10 W, 重复频率49.09 MHz(对应202 nJ的单脉冲能量), 脉冲宽度为1.03 ps的稳定锁模脉冲输出, 经过腔外色散补偿得到的脉冲宽度为95.5 fs.     

Doping management for high-power fiber lasers: 100 W, few-picosecond pulse generation from an all-fiber-integrated amplifier

Thermal effects, which limit the average power, can be minimized by using low-doped, longer gain fibers, whereas the presence of nonlinear effects requires use of high-doped, shorter fibers to maximize the peak power. We propose the use of varying doping levels along the gain fiber to circumvent these opposing requirements. By analogy to dispersion management and nonlinearity management, we refer to this scheme as doping management. As a practical first implementation, we report on the development of a fiber laser-amplifier system, the last stage of which has a hybrid gain fiber composed of high-doped and low-doped Yb fibers. The amplifier generates 100?W at 100?MHz with pulse energy of 1 μJ. The seed source is a passively mode-locked fiber oscillator operating in the all-normal-dispersion regime. The amplifier comprises three stages, which are all-fiber-integrated, delivering 13?ps pulses at full power. By optionally placing a grating compressor after the first stage amplifier, chirp of the seed pulses can be controlled, which allows an extra degree of freedom in the interplay between dispersion and self-phase modulation. This way, the laser delivers 4.5?ps pulses with ～200 kW peak power directly from fiber, without using external pulse compression.     

Microjoule-level all-polarization-maintaining femtosecond fiber source

We report on a high-power, high-energy femtosecond fiber source based on direct amplification of parabolic pulses from an environmentally stable passively mode-locked fiber oscillator in an Yb-doped single-polarization photonic crystal fiber. The special pulse shape allows for the generation of high-quality femtosecond pulses beyond nonlinearity limits. The system delivers a pulse energy of 1.2 microJ (21 W average power) at a repetition rate of 17 MHz and a pulse duration of 240 fs in a linearly polarized beam with diffraction-limited quality.     

Generation of 50-fs, 5-nJ pulses at 1.03 micrometre from a wave-breaking-free fiber laser

We report the generation of 6-nJ chirped pulses from a mode-locked Yb fiber laser at 1.03 micrometre. A linear anomalous-dispersion segment suppresses wave-breaking effects of solitonlike pulse shaping at high energies. The dechirped pulse duration is 50 fs, and the energy is 5 nJ. This laser produces twice the pulse energy and average power, and approximately five times the peak power, of the previous best mode-locked fiber laser. It is to our knowledge the first fiber laser that directly offers performance similar to that of solid-state lasers such as Ti:sapphire.