Indentation-induced microhardness changes in glasses: Possible fictive temperature increase caused by plastic deformation

The microhardness around a large indentation was measured for different types of glasses. In soda-lime silicate glass, a typical normal glass, the region in the immediate vicinity of the indentation was found to exhibit a lower hardness than the region far removed from the indentation. In silica glass, a typical anomalous glass, the region in the immediate vicinity of a large indentation was found to exhibit a higher hardness than the region far removed from the indentation. Asahi less brittle glass, an intermediate glass between normal and anomalous glasses, was found to exhibit little change in hardness in the vicinity of the large indentation. These findings can be explained by a deformation-induced fictive temperature increase leading to a lower hardness for soda-lime silicate glass and a higher hardness for silica glass.     

Development and properties of a glass made from MSWI bottom ash

A uniform shiny black-coloured glass was obtained using bottom ash produced by a Portuguese municipal solid waste incinerator (MSWI). The bottom ash was the single batch material used in the formation of the glass, which was obtained by vitrification of the solid waste at 1400 °C for 2 h. Under these conditions, a homogeneous melt with an appropriate viscosity to be shaped was obtained, indicating the suitability of this waste material to be employed in the development of vitreous products. The characterization of the resulting glass was performed in order to assess its structural, physical, mechanical, thermal and chemical features. The glass had a density of 2.69 g cm⁻³, a hardness of 5.5 GPa, a fracture strength of 75 MPa, a thermal expansion coefficient of 9.5 × 10⁻⁶ °C⁻¹ and it exhibited a very good chemical stability. In summary, the MSWI bottom ash glass has good mechanical and chemical properties and may, therefore, be used in several applications, particularly as a construction material.     

Nanoindentation of glass wool fibers

The nanoindentation technique is used to analyze the depth dependence of the hardness and the reduced elastic modulus of bulk glasses and glass wool fibers (4-12 μm in diameter) of calcium aluminosilicate composition. In spite of the fiber geometry and the delicate sample mounting-technique, nanoindentation proves to be a relatively accurate method that provides reproducible data for both hardness (H) and reduced elastic modulus (E_r) of thin glass fibers. It is found that H and E_r are generally lower for the fiber than for the bulk sample. Within a given fiber, both H and E_r are approximately constant with increasing indentation depth. However, both of these parameters decrease with diminishing fiber diameter. This trend is attributed to an increase of the free volume of the fibers with decreasing fiber diameter, i.e. to an increase of the fictive temperature.     

Sub-critical crack growth rate of soda-lime-silicate glass and less brittle glass as a function of fictive temperature

Sub-critical crack growth rates of soda-lime-silicate glass and less brittle glass with different fictive temperatures were compared using the DCDC method under both dry and humid atmospheres in order to investigate the origin of the unique mechanical features of the less brittle glass developed by Ito and his collaborators. In both dry and humid atmospheres, the crack velocity of the soda-lime-silicate glass was slower than that of the less brittle glass. For both glasses, the glass sample with higher fictive temperature showed a slower crack growth rate under both dry and humid atmospheres. These observations can be explained by the tendency for the plastic flow at the crack tip; the soda-lime-silicate glass is expected to show easier plastic flow under tension than the less brittle glass, and also the samples with higher fictive temperatures are expected to show easier plastic flow, leading to greater fracture toughness, K_IC, and slower crack growth rate.     

Doping-induced formation of bulk nanocrystalline alloy from metallic glass with controllable microstructure and properties

We report the formation of bulk nanocrystalline alloys from a Pr-based bulk metallic glass-forming alloy by doping iron. The microstructure of the alloys can be tuned progressively from full glassy state to composite with nanocrystalline particles in the glassy matrix, and finally into nanostructured state accompanying with the gradual magnetic and mechanical changes. The role of the addition in the control of microstructure and magnetic property, the mechanism for the nanocrystalline formation induced by addition, and the relation between the microstructure and properties are discussed.     

Glass formation ability and mechanical properties of Ti40Cu40Zr10Ni10 alloy

Melt-spun ribbon and bulk samples in cylindrical rod form with diameter ranging from 2 mm to 4 mm of Ti₄₀Cu₄₀Zr₁₀Ni₁₀ alloy were prepared by melt-spinning technique and copper mould casting method, respectively. The microstructure, thermal stability and mechanical properties of the bulk samples were investigated. A completely glassy single phase is formed in the 2 mm rod sample. Increasing the diameter of the rod samples resulted in the formation of CuTi crystalline phase in the 3 mm and 4 mm rod samples. The 2 mm single glassy rod sample exhibited a large supercooled liquid region ΔT_x = 58 K and γ = T_x/(T_g + T_l) is 0.390, which indicated that the alloy possessed a good glass-forming ability. The bulk samples also exhibited good mechanical properties. The 2 mm rod sample showed the highest yield strength of about 2086 MPa. The 3 mm rod sample not only showed high yield strength of about 2000 MPa, but also enhanced plastic strain of about 0.71%.     

Superscratch-resistant glass by means of a transparent nanostructured inorganic coating

Silica nanoparticles were synthesized by a reverse microemulsion method and deposited on soda-lime silica substrates. The deposition of these nanoparticles by dip-coating gave rise to close-packed layers, which significantly modify the scratch resistance of the surface. The silica nanoparticles are found to spread out the stress at the surface/indenter contact and to favor microductile behavior.     

Synthesis and characterization of calcium phosphate based bioactive quaternary P2O5-CaO-Na2O-K2O glasses

Calcium phosphate based bioactive quaternary glass systems P₂O₅-CaO-Na₂O-K₂O were prepared by melt growth technique. Glasses were prepared in five different compositions by fixing P₂O₅ at 47 mol% and CaO at 30.5 mol% and by varying the K₂O and Na₂O concentrations. The structural properties of the glasses are analyzed using X-ray diffraction (XRD) studies and scanning electron microscopy (SEM) studies; and the composition of the glasses are studied using energy dispersive X-ray spectrum (EDS). The microhardness of the glass systems are studied by Vickers hardness measurements and the bioactivity of the glasses are studied using in vitro study. The thermal properties have been examined by means of thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The ultrasonic velocity measurements show that the addition of K₂O contents produces non-bridging oxygen ion and hence weaken of the glass structure. The weakening of the glass structure reduces the ultrasonic velocity and hence an increase in attenuation.     

Formation, mechanical properties and corrosion resistance of Ti-Pd base glassy alloys

No biocompatible Ti-based glassy alloys without a harmful element have been reported. We have examined the mechanical and chemical properties of Ti-Pd-Zr-Si glassy alloy in comparison with pure Ti metal and Ti-6Al-4V alloy which have been used so far for biomaterials. The present Ti-Pd base glassy alloys do not contain Al and Ni elements which are considered to be rather toxic. Melt-spun Ti₄₅Zr_50−xPd_xSi₅ glassy alloy ribbons (x = 35, 40, 45) exhibited good bend ductility and had higher Vickers’s hardness and lower Young’s modulus as compared to pure titanium and Ti-6Al-4V alloy. In addition, the Ti₄₅Zr_50−xPd_xSi₅ glassy alloys had higher corrosion resistance and were passivated over a wide range and at the lower passive current density of approximately 10⁻² Am⁻² than at of pure titanium and Ti-6Al-4V alloy in 1 mass% lactic acid and PBS(−) solutions at 310 K.     

Thermal and some physical properties of glasses in the La2O3−CaO−B2O3 ternary system

Glasses in the La₂O₃−CaO−B₂O₃ ternary system were studied. The glass forming range as determined by the appearance of the annealed cast was found to match previously published findings. Clear glasses were formed in the composition range of 5.7−19.1 mol% La₂O₃ with constant B₂O₃ content of 71.4 mol%, and in glasses of constant La₂O₃:CaO ratio of 1:4 with B₂O₃ content in the range of 71.4-55.0 mol%. The non-linear optical crystalline phase La₂Ca₂B₁₀O₁₉ was crystallized from the clear glasses after heat treatments, as determined by powder XRD. Two types of the LaBO₃ crystalline phases were detected in the partially and the fully crystallized glass compositions outside the glass forming range. Data are reported for the glass transition temperature (T_g), dilatometric softening point (T_d), linear coefficient of expansion (α), onset crystallization temperature (T_x), exothermal peak temperature (T_P), density (ρ) and index of refraction (n_D) in the clear glasses.     

Point defect formation and annihilation in silica glass by heat-treatment: Role of water and stress

It was discovered that E′ centers were created by heat-treatment when silica glass contains water and has residual stress. Silica glass samples were heat-treated at 1000 °C for various lengths of time in 355 torr (47 000 Pa) water vapor pressure and dry nitrogen gas atmospheres. The electron paramagnetic resonance (EPR) signal of E′ centers increased initially with heat-treatment time in both atmospheres but then decreased afterwards in the wet atmosphere. It is known that water molecules eliminate paramagnetic defects, such as E′ centers and non-bridging oxygen hole centers (NBOHCs) by reacting with these defects in the glass, transforming them to non-paramagnetic species such as Si-OH or Si-H. The present study indicates that water molecules are also capable of initially creating paramagnetic defects in the glass structure by breaking the silica network structure in the presence of stress. The present observation may be relevant to mechanical strength reduction of silica glasses, which is commonly observed in the presence of water and stress.     

Crystallization behavior of glasses in the system of Na2O-CaO-MgO-Fe2O3-Al2O3-SiO2 with high contents of nickel oxide

The structural behavior of nickel oxide in glassy and glass-ceramic materials, obtained in the system of Na₂O-CaO-MgO-Fe₂O₃-Al₂O₃-SiO₂, was investigated. The influence of the NiO content on the vitrification, crystallization, structure and exploitation properties of two model compositions, with different ratios [CaO]/[MgO] was analyzed. On the basis of DSC and XRD data, it is shown that NiO promoted the formation of bunsenite crystals, as nuclei for crystallization. On the other hand, NiO promoted formation of pyroxenes even for compositions with low MgO contents, which formed gehlenite without NiO admixtures. It is shown that in the composition with relatively high MgO contents, NiO could participate in the formation of two types of pyroxenes with the structure and chemical composition similar to (MgO_0.4NiO_0.6)(CaO_0.9NiO_0.1)Si₂O₆ and diopside-hedenbergite solid solutions. The optimal contents of NiO in both model compositions was about of 7 wt%, since higher contents reduced the exploitation properties. The glass-ceramics with optimal contents of NiO were also produced using Ni bearing galvanic slurry and coal ash; the resulting materials showed similar exploitation properties to those mentioned above.     

The effect of thermal annealing on the structural and mechanical properties of a-C:H thin films prepared by the CFUBM magnetron sputtering method

a-C:H films were prepared by closed-field unbalanced magnetron (CFUBM) sputtering on silicon substrates using argon (Ar) and acetylene (C₂H₂) gases, and the effects of post-annealing temperature on structural and mechanical properties were investigated. Films were annealed at temperatures ranging from 300 °C to 700 °C in increments of 200 °C using rapid thermal annealing equipment in vacuum ambient. Variations in microstructure were examined using Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). Surface and mechanical properties were investigated by atomic force microscopy (AFM), nano-indentation, residual stress tester, and nano-scratch tester. We found that the mechanical properties of a-C:H films deteriorated with increased annealing temperature.     

Dense amorphous packing of binary hard sphere mixtures with chemical order: The stability of a solute ordered approximant

Recently, Miracle proposed that the intermediate structure in metallic glasses could be usefully characterized as an ordered face centered cubic packing of solute-centered coordination clusters. In this paper we examine the stability of such solute ordered arrangements in binary hard sphere mixtures subject to density maximization through local particle moves.     

The structure of SiO2-GeO2 glasses: A spectroscopic study

Four glasses of the SiO₂-GeO₂ binary system have been synthesized via a sol-gel route followed by a heat treatment and a quench. Glass structure has been determined by Ge K-edge X-ray absorption spectroscopy (XAS) at low temperature and Raman spectroscopy. These mixed glasses present a continuous random network of interconnected GeO₄ and SiO₄ tetrahedra, with GeO₄ tetrahedra similar to the GeO₄ units in GeO₂ glass and continuous compositional variations from GeO₂-rich regions to SiO₂-rich regions. Such a random mixture is consistent with physical properties of these binary glasses as well as with the chemical dependence of their polyamorphism at high pressure. This EXAFS-derived mean Ge-O-Si angles are close to the Ge-O-Ge mean angle in GeO₂ glass, 134° and 130°, respectively. This misfit with the Si-O-Si angles might explain the ease of formation of isolated and pair defects centers, which are suspected to be at the origin of photo-induced modifications of optical properties in Ge-bearing SiO₂ glasses.     

The structure of GeO2-SiO2 glasses and melts: A Raman spectroscopy study

We have investigated a series of glasses and melts along the GeO₂-SiO₂ join using insitu Raman spectroscopy. The results for both the glasses and melts are consistent with a continuous random network in which there are ‘regions’ that are SiO₂-like, GeO₂-like and mixed GeO₂-SiO₂-like. Incorporation of GeO₂ into the SiO₂ network is initially accommodated via the 3- and 4-membered SiO₄ rings which are lost as they convert to larger mixed Ge/Si rings. The LO-TO mode behavior is also consistent with a network that is composed of different ‘regions’ and is similar to that expected from the Bruggeman effective media model. At the highest temperatures there are indications that the mixed Ge/Si rings convert back to small 3-membered GeO₄ rings and large SiO₄ rings; the small 3- and 4-membered SiO₄ rings are not reformed.     

Studies of some mechanical and optical properties of: (70 − x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Specimens of the glassy system: (70 − x)TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by the melt-quenching. An ultrasonic pulse-echo technique was employed, at 5 MHz, for measuring: the ultrasonic attenuation, longitudinal and shear wave velocities, elastic moduli, Poisson ratio, Debye temperature and hardness of the present glasses. It is found that the gradual replacement of TeO₂ by Li₂O in the glass matrix up to 30 mol% leads to decrease the average crosslink density and rigidity of prepared samples which affects the properties, i.e., the hardness, ultrasonic wave velocities and elastic moduli are decreased, while the Poisson ratio and the ultrasonic attenuation are increased. Also, optical absorption spectra were recorded in the range, 200-800 nm for these glasses. The obtained results showed that a gradual shift in the fundamental absorption edge toward longer wavelengths occurred. Values of both of the optical energy gap, E_opt, and width tails, ΔE, are determined. It is observed that E_opt is decreased and ΔE increased with the increase of Li₂O in the glass matrix up to 30 mol%. The compositional dependences of the above properties are discussed and correlated to the structure of tested glasses.     

Nickel-alumina composite aerogel catalysts with a high nickel load: a novel fast sol-gel synthesis procedure and screening of catalytic properties

Nickel-alumina composite aerogels with large nickel loading were synthesized using a novel complexing agent-assisted sol-gel procedure to obtain materials displaying very large and open internal surface area, easily accessible for large molecules and demonstrating excellent catalytic properties. They were tested in the following reactions: (i) hydrogenation of propene and 1-butene, (ii) methanization of carbon dioxide, (iii) isometization of 1-butene, (iv) dehydrogenation of cyclohexane, (v) conversion of equimolar mixture of CO and NO to CO₂ and N₂. Full conversions and 100% selectivities were obtained in reactions (i), (ii), (iv) and (v) and an equilibrium composition in reaction (iii). These catalysts showed no pyrophoric activity on exposing to air even at Ni content as large as 50 wt%.