Eu3+掺杂CaWO4红色荧光粉发光性质的浓度依赖关系研究

采用共沉淀法制备了不同Eu³⁺掺杂浓度的CaWO₄荧光粉材料.通过X射线衍射和场发射扫描电镜技术对样品的结构和形貌进行了表征.测量了各样品的激发光谱、发射光谱和荧光衰减曲线, 计算了各样品的部分Judd-Oflet (J-O)参数和^5D_0 (Eu³⁺)能级量子效率,以及荧光粉的色坐标, 讨论了样品电荷迁移带相对强度、J-O参数、量子效率与掺杂浓度的依赖关系.对Eu³⁺掺杂的CaWO₄ 发光材料的光致发光性质的研究表明,在CaWO₄: Eu³⁺中⁵D₀→⁷F₂跃迁的616~nm 红色发光能被394.5~nm和465~nm的激发光有效激发,具有近紫外(或蓝光)激发效率高和猝灭浓度大的优点, 有潜力成为高效的近紫外(或蓝光)激发白光发光二极管用红色荧光粉材料.     

Synthesis of Gd2Ti2O7:Eu, V phosphors by sol-gel process and its luminescent properties

A red-emitting phosphor material, Gd₂Ti₂O₇:Eu³⁺, V⁴⁺, by added vanadium ions is synthesized using the sol-gel method. Phosphor characterization by high-resolution transmission electron microscopy shows that the phosphor possesses a good crystalline structure, while scanning electron microscopy reveals a uniform phosphor particle size in the range of 230-270 nm. X-ray photon electron spectrum analysis demonstrates that the V⁴⁺ ion promotes an electron dipole transition of Gd₂Ti₂O₇:Eu³⁺ phosphors, causing a new red-emitting phenomenon, and CIE value shifts to x=0.63, y=0.34 (a purer red region) from x=0.57, y=0.33 (CIE of Gd₂Ti₂O₇:Eu³⁺). The optimal composition of the novel red-emitting phosphor is about 26% of V⁴⁺ ions while the material is calcinated at 800  °C. The results of electroluminescent property of the material by field emission experiment by CNT-contained cathode agreed well with that of photoluminescent analysis.     

Surface characterization and luminescent properties of SrAl2O4:Eu,Dy nano thin films

SrAl₂O₄:Eu²⁺, Dy³⁺ thin films were grown on Si (1 0 0) substrates in different atmospheres using the pulsed laser deposition (PLD) technique. The effects of vacuum, oxygen (O₂) and argon (Ar) deposition atmospheres on the structural, morphological and photoluminescence (PL) properties of the films were investigated. The films were ablated using a 248 nm KrF excimer laser. Improved PL intensities were obtained from the unannealed films prepared in Ar and O₂ atmospheres compared to those prepared in vacuum. A stable green emission peak at 520 nm, attributed to 4f⁶5d¹→4f⁷ Eu²⁺ transitions was obtained. After annealing the films prepared in vacuum at 800 °C for 2 h, the intensity of the green emission (520 nm) of the thin film increased considerably. The amorphous thin film was crystalline after the annealing process. The diffusion of adventitious C into the nanostructured layers deposited in the Ar and O₂ atmospheres was most probably responsible for the quenching of the PL intensity after annealing.     

Effect of Eu,Tb codoping on the luminescent properties of Y2O3 nanorods

Red-emitting Y₂O₃:Eu³⁺ and green-emitting Y₂O₃:Tb³⁺ and Y₂O₃:Eu³⁺, Tb³⁺ nanorods were synthesized by hydrothermal method. Their structure and micromorphology have been analyzed by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The photoluminescence (PL) property of Y₂O₃:Eu³⁺,Tb³⁺ phosphor was investigated. In the same host (Y₂O₃), upon excitation with ultraviolet (UV) irradiation, it is shown that there are strong emissions at around 610 and 545 nm corresponding to the forced electric dipole ⁵D₀-⁷F₂ transition of Eu³⁺ and ⁵D₄-⁷F₅ transition of Tb³⁺, respectively. Different qualities of Eu³⁺and Tb³⁺ ions are induced into the Y₂O₃ lattice. From the excitation spectrum, we speculate that there exists energy transfer from Tb³⁺ to Eu³⁺ ions .The emission color of powders reveals regular change in the separation of light emission. These powders can meet with the request of optical display material for different colors or can be potentially used as labels for biological molecules.     

Preparation and luminescence properties of Tb doped ZrO2 and BaZrO3 phosphors

ZrO₂:Tb³⁺ and BaZrO₃:Tb³⁺ powders are prepared by combustion synthesis method and the samples were further heated to 500, 700 and 1000 °C to improve the crystallinity of the materials. The structure and morphology of materials have been examined by X-ray diffraction, Raman spectra and scanning electron microscopy. It is remarkable that all the samples of ZrO₂:Tb³⁺ and BaZrO₃:Tb³⁺ have similar morphology. These images exhibited homogeneous aggregates of varying shapes and sizes, which are composed of a large number of small cuboids and broken cuboids. The cuboids and broken cuboids size of all the samples are less than 0.5 μm. Photoluminescence for both materials increases with increase of temperature and found maximum for the samples heated to 1000 °C with 5 mole% doping of Tb³⁺ ions. Luminescence is almost double for the zirconia compared to that of barium-zirconate.     

Synthesis,characterization and photoluminescence of Eu3+, Ce3+ co-doped CaLaAl3O7 phosphors

Powder phosphors of CaLa_{1? x} Eu _x Al₃O₇, CaLa_{1? x} Ce _x Al₃O₇ and CaLa_{0.99? x} Eu _x Ce_0.01Al₃O₇, where x = 0.01, 0.03, 0.05 and 0.07, were prepared by a combustion method. The powders were well characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and photoluminescence techniques. Emission spectra of Eu³⁺-doped powder phosphors showed strong red emission at 613 nm (⁵D₀ → ⁷F₂); no concentration quenching was observed. Generally, Ce³⁺ acts as an efficient sensitizer when doped with other trivalent lanthanide ions. However, interestingly, in the CaLaAl₃O₇ powder phosphors, the addition of Ce³⁺ with Eu³⁺ exhibited an adverse effect–decreased photoluminescence intensity. The reasons for this behavior are discussed.     

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu,Dy phosphors prepared by solid state reaction method

Long persistent SrAl₂O₄:Eu²⁺ phosphors co-doped with Dy³⁺ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl₂O₄ were observed in all the samples. The broad band emission spectra at 497 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ were observed and the emission is attributed to the 4f⁶5d¹ to 4f⁷ transition of Eu²⁺ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy³⁺ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.     

Synthesis and luminescent properties of Y6W2O15:Eu phosphors

In this paper, a novel phosphor, Y₆W₂O₁₅:Eu³⁺ was synthesized by thermal decomposition and phase transition of its decatungstate gel precursor. With stepwise increase of temperature to 750 °C, a crystalline phase of Y₆W₂O₁₅:Eu³⁺forms that gives intense red emission when excited at 466 nm, the emission is attributed to the Eu³⁺ ions transitions from ⁵D₀ excited states to ⁷F_J (J=0-4) ground states. The long excitation wavelength proves the Eu³⁺ transition follows the photoexcitation of the oxygen-metal (O→W lmct) charge transfer bands in yttrium tungstate. Some structural information regarding Y₆W₂O₁₅ provided by luminescence is in accord with that characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The long-wavelength excitation properties of this material may find application in the production of red phosphors for white light-emitting diodes (LEDs).     

Photoluminescence characterization of Ce and Dy doped Li2CaGeO4 phosphors

Ce³⁺ and Dy³⁺ activated Li₂CaGeO₄ phosphors were prepared by a solid-state reaction method, and characterized by XRD (X-ray diffraction) and photoluminescence techniques. The characteristic emission bands of Dy³⁺ due to ⁴F_9/2→⁶H_15/2 (blue) and ⁴F_9/2→⁶H_13/2 (yellow) transitions were detected in the emission spectra of Li₂CaGeO₄:Dy³⁺. Ce³⁺ broad band emission was observed in Li₂CaGeO₄:Ce³⁺ phosphors at 372 and 400 nm due to 5d→4f transition when excited at 353 nm. Co-doping of Ce³⁺ enhanced the luminescence of Dy³⁺ significantly and concentration quenching occurs when Dy³⁺ is beyond 0.04 mol%. White-light with different hues can be realized by tuning Dy³⁺ concentration in the phosphors.     

The effect of flux materials on the physical and optical properties of Eu-activated yttrium oxide phosphors

A flux fusion method was used to obtain the various sizes of Eu³⁺-activated Y₂O₃ red phosphors. The flux material was selected as an independent variable to control the physical properties of phosphor particles and their effects on the morphology and size distribution of phosphors were examined by scanning electron microscopy. The concentration of the flux materials and synthetic temperature were optimized for maximal photoluminescence intensity. Fluoride-based flux materials were found to work for the crystal formation of Eu³⁺-activated Y₂O₃. In particular, when a BaF₂ flux was used during the reaction at 1450 °C for 3 h, the photoluminescence (PL) intensity of Eu³⁺-activated Y₂O₃ was 25% higher than that without a flux and spherical phosphors had a mean particle size of 4-5 μm. The morphology and size distribution of the synthesized Eu³⁺-activated Y₂O₃ phosphor were predominantly dependent upon the type and concentration of flux material and synthetic temperature.     

The up-conversion properties of Yb and Er doped Y4Al2O9 phosphors

Er³⁺ doped and Yb³⁺/Er³⁺ co-doped Y₄Al₂O₉ phosphors are prepared by the sol-gel method. The effect of dopant concentration on the structure and up-conversion properties is investigated by X-ray diffraction (XRD) and photoluminescence, respectively. XRD pattern indicates that the sample structure belongs to monoclinic. Under 980 nm excitation, the green and red up-conversion emissions are observed and the emission intensities depended on the Yb³⁺ ion concentration. The green up-conversion emissions decrease with the increase of Yb³⁺ concentration, while red emission increases as Yb³⁺ concentration increases from 0 to 8 at% and then decreases at high Yb³⁺ concentration. The mechanisms of the up-conversion emissions are discussed and results shows that in Er³⁺ and Yb³⁺/Er³⁺ co-doped system, cross-relaxation (CR) and energy transfer (ET) processes play an important role for the green and red up-conversion emissions.     

Synthesis and properties of submicron range CaSO4:Eu particles

CaSO₄:Eu with particle size in submicron range was synthesized. Radiation induced Eu³⁺↔Eu²⁺ conversion as well as thermal conversion was studied. The samples showed thermal conversion above 400 °C. However, no radiation induced conversion in submicron range particles was observed. Particles heated above 400 °C coalesce and when heated at 925 °C bigger particles of 20 μm size were formed. Optical microscopy of these particles reveals red inclusion of about 5 μm inside CaSO₄ particle. It is speculated that the red inclusion is CaS:Eu²⁺.     

Eu,Li doped CaWO4 nanorods: Synthesis,emission-decay curves and effective-refractive index

In the present paper, CaWO₄: Eu³⁺, Li⁺ nanorods have been successfully synthesized via an oleic acid (OA)-assisted solvethermal route. The transmission electron microscope (TEM) photograph shows that the CaWO₄: Eu³⁺, Li⁺ nanorods are monodisperse and uniform nanorods with average diameter of 26 nm. The optical properties of Eu³⁺ in CaWO₄ samples, including photoluminescence (PL) excitation spectra and luminescent decay curves, are investigated in detail. Due to the form of the nanorods, the relative contribution of CTB to the nanorods sample is greater than that to the bulk counterparts. The decay time of the ⁵D₀ level (ranging from 0.94 to 0.65 ms, depending on the filling factor of the nanorods) of the nanorods is longer than that of the bulk counterpart mainly due to the reduction in the size of the nanorods, which introduces an effective-refractive index smaller than the refractive index of CaWO₄.     

Effect of Bi on fluorescence properties of YPO4:Dy phosphors synthesized by a modified chemical co-precipitation method

Y_0.99−xPO₄:0.01Dy³⁺, xBi³⁺ (x=0, 0.01, 0.05, 0.10, 0.15, 0.20 and 0.25) phosphors have been synthesized by a modified chemical co-precipitation method using urea as a pH value regulator. The samples were characterized by X-ray powder diffraction (XRD) and photoluminescence spectroscopy. XRD results show that the samples have only single tetragonal structure when x≤0.15, but extraneous BiPO₄ phase appears besides major tetragonal phase when x≥0.20. The crystallinity of the samples is found to improve with increasing Bi³⁺ ion concentration from 0 to 15 mol%, and then decreased for higher concentrations associated with increasing BiPO₄ phase. Photoluminescence excitation spectra results show that the phosphor can be efficiently excited by ultraviolet light from 250 to 400 nm including four peaks at 294, 326, 352 and 365 nm. Emission spectra exhibit strong blue emission (483 nm) and another strong yellow emission (574 nm). When the Bi³⁺ ion concentration is 1 mol%, the intensity of excitation and emission spectra increased evidently. In addition, the yellow-to-blue emission intensity ratio (I_Y/I_B) is strongly related to the excitation wavelength and not to the Bi³⁺ ion concentration.     

Radiation effects on luminescent and structural properties of YPO4: Pr3+ nanophosphors

ABSTRACT

YPO₄ phosphors doped with trivalent ion Pr³⁺ were prepared by sol–gel method and treated with different doses of gamma radiation, from 0.25 MGy to 4 MGy. Effects of radiation on morphology, structure and luminescent properties were analyzed. Also, the influence of radiation on the change in the color of the samples was examined. The color efficiency of powders was evaluated by colorimetric analysis (CIE and L * a * b system). It has been observed that powders change color under the influence of radiation, i.e. they pass from white to pinkish red. Also, it has been determined that the radiation affects morphology change, as the particle size increases with increasing of the radiation dose. With the increase in the radiation dose, the emission intensity of samples decreases. The structure remains almost unchanged after irradiation, and the intensity constantly decreases with increasing of dose.     

Photophysical properties of highly efficient red-emitting CaTiO3:Eu phosphors under near ultra-violet excitation

The photophysical properties of europium-doped calcium titanate for near ultra-violet excitation were studied in order to investigate whether it is applicable to white light-emitting diodes. CaTiO₃:Eu³⁺ phosphors were synthesized by using the solid-state reaction method. The structures and basic properties of the phosphors were characterized by using X-ray diffractometer, scanning electron microscope, UV-visible spectrophotometer, and X-ray photoelectron spectrometer. The photophysical properties were examined by taking excitation and emission spectra. A strong red luminescence corresponding to ⁵D₀ → ⁷F₂ transition of Eu³⁺ under near ultra-violet excitation was observed. It was found that CaTiO₃:Eu³⁺ was a red-emitting phosphor and had higher efficiency for operation under near ultra-violet excitation.     

Synthesis and luminescent properties of nanoparticles GdCaAl3O7:RE (RE=Eu, Tb) via the sol-gel method

By using metal nitrates as starting materials and citric acid as complexing agent, GdCaAl₃O₇:Eu³⁺ and GdCaAl₃O₇:Tb³⁺ powder phosphors were prepared by a citrate-gel method. Thermal analysis (TG-DTG), X-ray diffraction (XRD), transmission electron microscope (TEM) and scanning electron microscope (SEM), photoluminescence excitation and emission, as well as kinetic decays were employed to characterize the resulting samples. The results of the XRD indicated the precursor samples began to crystallize at 800 °C and the crystallinity increased with elevation the annealing temperature. TEM images showed that the phosphor particles were basically of spherical shape, with good dispersion about a particle size of around 40-70 nm. Upon excitation with UV irradiation, it is shown that there is a strong emission at around 617 nm corresponding to the forced electric dipole ⁵D₀-⁷F₂ transition of Eu³⁺, and at around 543 nm corresponding to the ⁵D₄-⁷F₅ transition of Tb³⁺. The dependence of photoluminescence intensity on Eu³⁺ (or Tb³⁺) concentration and annealing temperature were also studied in detail.     

Synthesis and luminescent properties of nanoparticles LaSrAl3O7:Eu, Tb

Phosphors of nanoparticles LaSrAl₃O₇:RE³⁺(REEu, Tb) have been prepared by a sol–gel method. The structure and luminescent properties of LaSrAl₃O₇:Eu³⁺ and LaSrAl₃O₇:Tb³⁺ phosphors were characterized by X-ray diffraction and atomic force microscopy (AFM), photoluminescence excitation and emission spectra were utilized. From X-ray diffraction (XRD) patterns, it is indicated that the phosphor LaSrAl₃O₇ forms without impurity phase at 900 °C. From atomic force microscopy (AFM) images, it is shown that the crystal size of the phosphores are about 60–80 nm. Upon excitation with UV irradiation, it is shown that there is a strong emission at around 617 nm corresponding to the forced electric dipole ⁵D₀–⁷F₂ transition of Eu³⁺, and at around 545 nm corresponding to the ⁵D₄–⁷F₅ transition of Tb³⁺. The dependence of photoluminescence intensity on Eu³⁺(or Tb³⁺) concentration and annealing temperature were also studied in detail.     

Synthesis, structure and optical properties of Eu/TiO2 nanocrystals at room temperature

The nanocrystal samples of titanium dioxide doped with europium ion (Eu³⁺/TiO₂ nanocrystal) are synthesized by the sol-gel method with hydrothermal treatment. The Eu³⁺ contents (molar ratio) in the samples are 0, 0.5%, 1%, 2%, 3% and 4%. The X-ray diffraction, UV-Vis spectroscopy data and scanning electron microscope image show that crystallite size is reduced by the doping of Eu³⁺ into TiO₂. Comparing the Raman spectra of TiO₂ with Eu³⁺/TiO₂ (molar ratio Eu³⁺/TiO₂=1%, 2% and 4%) nanocrystals at different annealing temperatures indicates that the anatase-to-rutile phase transformation temperatures of Eu³⁺/TiO₂ nanocrystals are higher than that of TiO₂. This is due to the formation of Eu-O-Ti bonds on the surface of the TiO₂ crystallite, as characterized by the X-ray photoelectron spectroscopy. The photoluminescence spectra of TiO₂ in Eu³⁺/TiO₂ nanocrystals are interpreted by the surface self-trapped and defect-trapped exciton relaxation. The photoluminescence of Eu³⁺ in Eu³⁺/TiO₂ nanocrystals has the strongest emission intensity at 2% of Eu³⁺ concentration.     

Synthesis and properties of colloidal ternary ZnGa2O4:Eu nanocrystals

A nonhydrolytic hot solution synthesis technique was used to grow monodisperse ternary oxide nanocrystals of ZnGa₂O₄:Eu³⁺. The shape of ZnGa₂O₄:Eu³⁺ nanocrystals was a function of the type of precursor, and their size was controlled by changing the concentration ratio of Zn precursor to surfactant. The crystal structure of synthesized ZnGa₂O₄ nanocrystals was a cubic spinel with no detectable secondary phases. Photoluminescence of red-emitting ZnGa₂O₄:Eu³⁺ nanocrystals resulted in a high (⁵D₀-⁷F₂)/(⁵D₀-⁷F₁) intensity ratio, suggesting that the Eu³⁺ ions occupy tetrahedral Zn²⁺ sites or distorted octahedral Ga³⁺ sites with no inversion symmetry in ZnGa₂O₄ nanocrystals.