Numerical investigation and optimization of a photonic crystal fiber for simultaneous dispersion compensation over S + C + L wavelength bands

In this paper, we numerically investigate and optimize the profile of a photonic crystal fiber (PCF) that can eliminate the residual dispersion from the telecom link as well as can provide identical dispersion compensation over S + C + L bands. A full-vectorial finite element method combined with genetic algorithm is used to optimize the fiber’s profile as well as to accurately determine its modal properties. The optimized PCF exhibits a dispersion of −98.3 ps/nm/km with a variance of ±0.55 ps/nm/km from 1.48 μm to 1.63 μm (i.e., over 150 nm bandwidth) and a zero dispersion slope. Macro-bending loss performance of the designed PCF is also studied and it is found that the fiber shows low bending losses for the smallest feasible bending radius of 5 mm. Further, sensitivity analysis has been carried out for the proposed fiber design and it has been found that a ±2% change in the fiber parameters may lead to a ±8% shift of the dispersion from its nominal value.     

Transmission performance of 20 × 10 Gb/s WDM signals using cascaded optimized SOAs with OOK and DPSK modulation formats

We investigated 20 channels at 10 Gb/s wavelength division multiplexing (WDM) transmission over 1190 km single mode fiber and dispersion compensating fiber using cascaded inline semiconductor optical amplifier at a span of 70 km for RZ-DPSK (return zero differential phase-shift keying) modulation format by using same channel spacing, i.e. 100 GHz. We show for RZ-OOK (return zero on-off keying) format a transmission distance of up to 1050 km with Q factor more than 15 dB, without any power drops. We developed the SOA model for inline amplifier having minimum cross-talks and ASE (amplified spontaneous emission) noise power with sufficient gain. At optimal bias current of 400 mA, a high constant gain of 36.5 dB is obtained up to a saturation power of 21.36 mW. So reduction of cross-talk and distortion is possible by decreasing the bias current at appropriate amplification factor.The DPSK modulation format has less cross-talk as compared to OOK format for nonlinearities and saturation case. The impact of optical power received and Q factor at different distance for both RZ-OOK and RZ-DPSK modulation format has been illustrated. We have shown the optical spectrum and clear Eye diagram at the transmission distance of 1190 km in RZ-DPSK system and 1050 km in RZ-OOK systems.The bit error rate (BER) for all channels observed is less than 10⁻¹⁰ up to gain saturation for both DPSK and OOK systems. Finally, we investigated that the transmission distance decreases with a decrease in channel spacing of up to 20 GHz.     

Polarization maintaining holey fibers for residual dispersion compensation over S + C + L wavelength bands

We report on a highly birefringent holey fiber for broadband dispersion compensation covering the S, C, and L telecommunication bands i.e. wavelength ranging from 1460 to 1625 nm. The finite element method with circular perfectly matched layer boundary condition is used to investigate the guiding properties. Numerical analysis demonstrates that it is possible to obtain negative dispersion coefficient of about −470 to −850 ps/nm/km over S to L-bands and a relative dispersion slope perfectly matched with single mode fiber (SMF) of about 0.0036 nm⁻¹ at 1550 nm. At the same time birefringence of the order 2.53 × 10⁻² is realized at 1550 nm wavelength. Owing to superior optical properties of the proposed holey fiber, this can be a promising candidate for broadband dispersion compensation and sensing applications.     

Limitation in the intrinsic method of EDFA gain optimization for 32 × 40 Gbit/s WDM systems

The gain flattening of the erbium doped fiber amplifier (EDFA) is one of the most important aspects in the EDFA which the gain is wavelength dependent. For the first time the limitation of EDFA gain optimizing for a 32-channel wavelength division multiplexing (WDM) systems is investigated and reported in this paper. In a 32-channel WDM system the most favorable flatness gain achieved was 23.16 ± 1.51 dB with an average noise figure of 5.70 dB. This outcome proposes that the method does not achieve a uniform spectral gain in a 32-channel WDM system that incorporates a bandwidth of around 25 nm. Based on the simulation results the intrinsic optimization of EDFA causes the poor SNR and peak signal power with great variation over a transmission distance of 480 km single mode fiber.     

Performance comparison of pre-, post- and symmetrical-dispersion compensation techniques using DCF on 40 Gbps OTDM system for different fibre standards

Various factors like polarization mode dispersion, non-linear effects, Kerr effect, second and third order dispersion impose limit on the performance (transmission distance, pulse broadening) of Optical Time Division Multiplexed (OTDM) transmission system. In this paper, the performance comparison of 40 Gbps OTDM transmission system with pre-, post-, and symmetrical-dispersion compensation techniques for different fibre standards has been carried out. It has been observed that for pre compensation, ITU 655 [D = 3.78 ps/nm/km] came to be best suitable fibre with the dispersion compensating fibre length of 2.36 km for maximum reach of 3000 km. For post- and symmetrical-compensation, the behaviour of alcatel [D = 8 ps/nm/km] is almost similar with maximum transmission distance of 3200 and 3050 km respectively.     

Transmission system over 3000 km with dispersion compensated by chirped fiber Bragg gratings

The limitation of the system with dispersion compensation by chirped fiber Bragg gratings is investigated in this paper. The transmission distance of the system based on chirped fiber Bragg gratings surpasses 3000 km. The bit error rate (BER) of the system is below 10⁻⁹ for as long as 2000 km. The BER is about 10⁻⁷ at 3000 km and, when forward error correction (FEC) is added, zero BER can be achieved. It is the longest transmission system with dispersion compensation by chirped fiber Bragg gratings.     

Performance comparison between digital back propagation (DBP) and pilot-aided method for fiber nonlinearity compensation in different fiber links

We numerically investigate and compare the performance of fiber nonlinearity compensation using digital back propagation (DBP) method and pilot-aided method in coherent optical transmission systems using different fiber links. Simulations for wavelength division multiplexed (WDM) 112 Gb/s polarization division multiplexed quadrature phase shift keying (PDM-QPSK) systems with dispersion unmanaged (no DM) and dispersion managed (DM) fiber links are implemented. System Q-factor and maximum transmission distance at bit error rate (BER) of 3.8 ÿ 10^?3 are calculated for performance comparison. The results show that, for system with no DM fiber link, DBP method outperforms pilot-aided method, because DBP method has better performance for intra-channel fiber nonlinearity compensation. However, for system with DM fiber link where inter-channel fiber nonlinearity plays an important role, pilot-aided method performs better than DBP method, because of its ability for inter-channel fiber nonlinearity compensation.     

On duty cycle selection of RZ optical pulse to optimize the performance of dispersion compensated 10 Gbps single channel optical communication system using dispersion compensating fibers

We present results for duty cycle selection of optical RZ pulse to optimize the performance in 10 Gbps single channel dispersion compensated optical communication system. The system has link length of 240 km with two spans. Each of the spans consists of 120 km standard single mode fiber (SSMF) of 16 ps/nm/km, whose chromatic dispersion is compensated using pre-, post- and symmetrical-dispersion compensation schemes by 24 km dispersion compensating fiber (DCF) of −80 ps/nm/km. The performance of the three compensation schemes is compared by taking 8, 10, 12 and 14 dBm Er-doped fiber amplifier (EDFA) power levels in the link with a duty cycle range (0.1-0.9) of RZ optical pulse. The graphical results obtained show a relationship among the duty cycle, EDFA power and dispersion compensation scheme which predicts the best performing duty cycle case. To optimize performance of the system, we recommend in general, duty cycle less than 0.3 and EDFA power below 8 dB irrespective of compensation scheme. However, with post compensation duty cycle less than 0.7 and EDFA power below 12 dBm give optimum performance. The results conclude that for the high value of duty cycle, post dispersion compensation scheme should be used.     

The analysis of the error statistics in a 5 × 40 Gbit/s fibre link with hybrid amplification

We quantify the error statistics and patterning effects in a 5 × 40 Gbit/s WDM RZ-OOK SMF/DCF fibre link using hybrid Raman/EDFA amplification. By extensive use of a numerical model, we determine how the error statistics change with the transmission distance. This knowledge is used as a basis for a constrained coding technique in order to improve the transmission error rate. We propose an adaptive constrained code for mitigation of the patterning effects and demonstrate that this approach can substantially reduce the bit error rate (BER) even for very large values of the channel BER (BER > 10^− 1). The proposed technique can be used in combination with forward error correction schemes (FEC) to extend the range of channel BERs that an FEC scheme is effective over.     

Ultra-short pulse compression at 1065 nm in nonlinear photonic crystal fiber

A pulse compressor has been designed using a 13 mm highly nonlinear photonic crystal fiber to compress pulses centered at 1065 nm from 28 fs to 1.8 fs with a compression factor of 16.2. This compression is achieved by using a high level of energy and generating different orders of solitons without resorting to large values of fiber's dispersion.     

Enhanced performance for 10 Gb/s long reach RSOA based WDM-PON by using power pre-emphasized OFDM signal

An extended reach 10 Gb/s wavelength division multiplexing passive optical networks (WDM-PONs) system based on reflective semiconductor optical amplifier (RSOA) is proposed by using power pre-emphasized orthogonal frequency division multiplexing (OFDM) signal. Experimental results show that the proposed technique can effectively enhance the system performance against the limited bandwidth and chirp induced fading effect from direct modulation of RSOA. The receiver sensitivity is improved by 5 dB at the limit of BER for forward error correction (FEC) code over the 60 km and 85 km fiber transmission without any dispersion compensation module.     

Simulation of high capacity 40 Gb/s long haul DWDM system using different modulation formats and dispersion compensation schemes in the presence of Kerr's effect

In this paper, simulative analysis of 40 Gb/s long haul (500-2000 km) DWDM system with ultra high capacity upto 1.28 Tb/s has been carried out for carrier-suppressed return-to-zero (CSRZ), duobinary return-to-zero (DRZ) and modified duobinary return-to-zero (MDRZ) modulation formats. The DWDM system has been analyzed for the pre, post and symmetrical dispersion compensation schemes for 16 Channels with 25 GHz channel spacing in order to find the optimum modulation format for a high bit rate optical transmission system. The effect of variation in input power and transmission distances is observed in terms of Q value and eye opening for various formats. It is found that symmetrical compensation is superior to pre and post dispersion compensation schemes. It has also been observed that the performance of DWDM system is severely limited by the four-wave mixing (FWM) effect and is determined that MDRZ format seems to be the best choice for the transmission distance beyond 1550 km despite slightly more complex transmitter and receiver configuration. Further, symmetrical compensation scheme has been investigated for 32×40 Gb/s MDRZ format for faithful transmission over 1450 km.     

Reduction of the fiber nonlinearity impairment using optical phase conjugation in 40 Gb/s CO-OFDM systems

In this paper, optical phase conjugation (OPC) located in the transmitter based on four wave mixing (FWM) in a semiconductor optical amplifier (SOA) is first simulated in 40 Gb/s CO-OFDM systems, and the fiber nonlinearity impairment of the transmission link is precompensated before OPC by transmission through a fiber with large nonlinearity coefficient. Simulation results show that the nonlinear threshold (NLT) can be increased by about > 3 dB and maximum Q factor can be increased by about 2 dB for the single-channel system. For 50-GHz-Spacing WDM systems, the maximum Q and NLT are increased by about 1 dB, even in the presence of cross phase modulation (XPM) from neighbouring WDM channels. It is found that this OPC subsystem located in the transmitter, not necessary to be inserted into the middle of link, can mitigate the fiber nonlinearity impairment for both single-channel and WDM systems.     

Optimizing amplifier spacing to improve performance in RZ-rectangular pulse based 10 Gb/s single channel dispersion managed optical communication system

In this paper, we optimize the inter-amplifier spacing in combination with duty cycle of RZ data format and EDFAs power so that link length of system can be maximized. The results for EDFA amplifier placement in 10 Gbps single channel dispersion managed optical communication system have been presented. By increasing the length of standard single mode fiber of dispersion 16 ps/nm/km in proportion to the increase in length of compensating fiber of dispersion −80 ps/nm/km, the pre-, post- and symmetrical-dispersion compensation schemes of the system have been compared. Further, schemes are observed at 8, 10 and 12 dBm values of EDFA power in the link with different duty cycle values of RZ optical pulse in the range of 0.2-0.8 with step size of 0.2 in relation to amplifier spacing to get lower value of bit error rate and timing jitter. The graphical results obtained show strong relationship among duty cycle of RZ optical pulse, EDFA power and, dispersion compensation scheme.     

Investigations on order and width of RZ super Gaussian pulse in pre-, post- and symmetrical-dispersion compensated 10 Gb/s optical communication system using standard and dispersion compensating fibers

We show the effect of varied order and width of super Gaussian pulse at 10 Gb/s in dispersion compensated optical communication system. The optical communication system consists of standard single-mode fiber of 16 ps/nm/km of a certain length, whose dispersion is compensated using pre-, post- and symmetrical-dispersion compensation schemes with proportionate length dispersion compensating fiber of −80 ps/nm/km. Performance of these three compensation schemes is compared at 14 dBm values of Er-doped fiber amplifiers (EDFA) power at 1st, 2nd and 3rd order RZ super Gaussian optical pulse. The pulse width, full width at half maximum (FWHM) is also varied from 5 to 30 ps to highlight the optimum performance. The graphical results obtained show a relationship among the attributes pulse width, order of RZ super Gaussian optical pulse and dispersion compensation scheme implemented. It shows that to decrease BER and timing jitter in the system, smaller width and 3rd order super Gaussian pulse should be used. It is recommended that to decrease dependency of BER and timing jitter in the communication system on the pulse width i.e. FWHM, the symmetrical compensation scheme should be implemented.     

Tunable 12×10 GHz mode-locked semiconductor fiber laser incorporating a Mach-Zehnder interferometer filter

A stable multiwavelength mode-locked semiconductor fiber ring laser incorporating a fiber Mach-Zehnder interferometer (MZI) filter was proposed and experimentally demonstrated. A semiconductor optical amplifier (SOA) serves as an optically controlled mode-locking element due to gain exhaustion caused by external injected optical pulses. Another SOA severs as a constant-gain medium. A fiber MZI filter with a temperature control is incorporated into the fiber ring cavity to acquire a stable and tunable multiwavelength oscillation. Twelve wavelengths are synchronously mode-locked at 10 GHz, pulse width of mode-locked pulse are about 30 ps. Proposed multiwavelength mode-locked semiconductor fiber ring laser has some distinct advantages, such as simple and compact structure, easy integration, convenient tuning, good stability, potential high repetition rate operating, which has potential application in the future WDM communication system.     

Reduction in timing jitter by chirp selection for externally modulated return to zero optical soliton pulse at 10 Gb/s

We investigate the chirp selection of externally modulated RZ soliton pulse at 10 Gb/s for fiber optical communication systems for the reduction in timing jitter. We have chosen single arm Mach-Zehnder amplitude modulator with sin² electrical shaped input-output (P-V) characteristic and its chirp range has been varied in the range of −5 to 5. The timing jitter, Q factor and bit error rate (BER) generated for the chirp range has been studied for various fiber lengths and post compensation has been demonstrated to reduce the timing jitter. The number of fixed output amplifiers after every 60 km span is varied from 2 to 10 and corresponding accumulated ASE noise has been studied to manage timing jitter and BER in permissible range, i.e. 5 ps and 10⁻⁹, respectively. It is observed that when two fiber spans are taken then the compensating fiber length for the system is less than 20 km for each case of the chirp considered. For 10 fiber spans, the compensating fiber length increases in the range 60-90 km depending upon the value of chirp taken. Finally it is shown that the chirp value of external modulator should be set to either 0 or −1 for externally modulated RZ soliton pulse in 10 Gb/s optical communication system which makes the system more insensitive to the timing jitter and the selection of dispersion compensating fiber length.     

400 Gbps WDM transmission over short range with discrete multi-tone

We simulate 400 Gbps WDM transmission system with DMT modulation. The system reaches 5 km SSMF with 100 Gbps per wavelength when the BER is 1e−3. From our analyses, we can see that DMT can be a promising solution for high capacity optical transmission system over short distance.     

Impact of extinction ratio of single arm sin LiNbO3 Mach-Zehnder modulator on the performance of 10 and 20 Gb/s NRZ optical communication system

We investigate the impact of extinction ratio of single arm sin² LiNbO₃ Mach-Zehnder (MZ) amplitude modulator on the performance of 10 and 20 Gb/s single-channel optical communication system. For different fiber lengths, the system performance has been analyzed with the increase in the extinction ratio. The effect of variation in dispersion parameter has also been illustrated. The impact of extinction ratio (ζ), dispersion parameter and length of the fiber has been further optimized with minimum bit error rate (BER) at optimal decision threshold (10⁻⁹) for 10 and 20 Gb/s bit rate. It is found that the system gives optimum performance at extinction ratio (ζ) value 20 dB. The increase in the transmission distance from 468 km for 10 Gb/s to 532 km for 20 Gb/s has been reported, and 8 dB improvement in the Q value has been observed as the value of ζ is increased from 10 to 20 dB. At 20 Gb/s, the system gives optimum performance for dispersion parameter value only up to 4 ps/nm km; however, at 10 Gb/s the system can operate for dispersion values up to 14.3 ps/nm km. Further we investigate the self-phase modulation (SPM) effect for the increase in the input power. It is observed that the SPM effect is negligible below 3 dB m input power and it increases at higher power levels.