基于包层模的光纤布拉格光栅折射率传感特性

提出了基于光纤布拉格光栅(FBG)包层模式的折射率传感方案。实验中,利用不同浓度的丙三醇水溶液作为外界折射率传感溶液,采用氢氟酸溶液化学腐蚀的方法来减小光纤包层的直径以增大包层模式对外界折射率的敏感度,研究了腐蚀后光纤布拉格光栅包层模式的耦合波长对外部折射率的变化关系。实验结果表明在1.3300~1.4584的折射率范围内,包层模式耦合波长随外界折射率增大而增大,在接近光纤包层折射率处具有很高的折射率灵敏度,最大达到了172 nm/riu(refractive index unit)。而且,包层模谐振的光谱半峰全宽(约0.07 nm)仅为布拉格纤芯模谐振光谱半峰全宽的1/4,能够获得更好的传感精度。     

一种基于结构性改变的光子晶体光纤光栅理论研究

对一种新型基于结构性改变的光子晶体光纤光栅原理进行了研究.采用多极法分析了结构性改变对折射率的影响,得到有效折射率与包层气孔塌缩之间的关系,建立了结构性改变光子晶体光纤光栅模型.利用耦合模理论对所成光栅性能进行了分析,重点研究了包层空气孔层数、空气孔占空比、气孔塌缩程度对光栅谐振波长、带宽的影响.研究结果表明,光子晶体...     

Widely tunable long-period fiber grating with nm-thick higher refractive index film overlay

By introducing a four-layer step-index waveguide modeling, the characteristics of long-period fiber grating (LPFG) with an nm-thick film overlay, which has higher refractive index than that of fiber cladding are investigated in detail. The influence of both the overlay thickness and refractive index on the tuning ability of LPFG is analyzed. The numerical results demonstrate that spectral response of LPFG is divided into three distinct regions as the overlay deposition increases and the shift of resonant wavelength is drastic in some special thickness range. In conjunction with higher-order cladding mode coupling and fiber cladding etching, the sensitivity of LPFG to the overlay refractive index is enhanced significantly and over 120 nm resonant wavelength tunable range is achieved.     

Enhancement of sensitivity in long-period fiber gratings with deposition of low-refractive-index materials

It was proved [Opt. Lett. 30, 720 (2005)] that the deposition of an overlay of higher refractive index than that of the cladding on a long-period fiber grating (LPFG) causes large shifts in the attenuation bands induced by the grating. The result is an enhancement of the sensitivity of the LPFG to variations in the ambient and overlay refractive indices or the overlay thickness. The limitation of the previous design to materials with higher refractive indices than that of the cladding of the LPFG is overcome with a five-layer model. To this purpose, a first overlay of higher refractive index than that of the cladding of the LPFG will enhance the sensitivity of the device to variations in the refractive index of a second overlay of lower refractive index than that of the cladding of the LPFG. Moreover, it is proved that, if the second overlay is thick enough, its behavior resembles that of an infinite layer.     

有限包层半径光纤Bragg光栅的理论研究

采用光纤波导三层模型,对有限包层半径光纤Bragg光栅导模有效折射率的改变进行了理论分析,结果表明:当包层直径小于16μm时,单模光纤Bragg光栅(纤芯直径为8.3μm)的导模有效折射率才开始发生明显变化.在包层外添加外包层,通过改变外包层的折射率可以实现对光栅Bragg反射波长的调谐,同时对不同芯子直径的光栅Bragg波长移动进行了数值计算.在保证光纤归一化频率不变的前提下,芯径越小Bragg波长调谐范围越大,当包层厚度为1μm时,芯径为a＝2.2μm的光栅Bragg波长调谐范围约为3.9μm.     

不同包层直径的倾斜光纤光栅折射率传感特性

倾斜光纤光栅的透射谱中有纤芯模和大量的包层模,它们具有与布拉格光栅相同的温度特性.利用HF酸腐蚀的方法得到具有不同包层直径的倾斜光纤光栅,研究了其对外界折射率的传感特性.结果表明,外界环境折射率在1.333～1.4532之间变化时,同一直径倾斜光纤光栅的高阶包层模的敏感性要比低阶包层模强;随着包层直径的减小,包层模的敏感性增强,且在折射率比较高的环境中有更高的敏感性.因此,利用倾斜光纤光栅的温度特性不仅可以解决温度交叉敏感问题,而且通过小同的腐蚀程度能定制所需要的灵敏度,以实现对环境折射率的高灵敏度测量.该办法可应用于对生物和化学等高灵敏度传感领域的各种溶液进行实时监控.     

Theoretical analysis of novel fiber grating pair

A novel fiber grating pair that consists of a conventional long-period fiber grating and a fiber Bragg cladding grating (FBCG) is proposed. The FBCG is a new type of fiber grating in which refractive index modulation is formed in the cladding. Through the coupled-mode theory, we accurately calculate the coupling coefficients between modes supported in the fibers. And some other mode coupling features in the fiber cladding gratings are analyzed in detail. The calculation of the modes involved in this paper is based on a model of three-layer step-index fiber geometry. Then, we have investigated the sensitivity characteristics for variation of the modulation strengths of the fiber Bragg cladding gratings’ resonance peaks and the long-period cladding gratings’ (LPCGs) dual resonant peaks. Finally, the modulation strength sensitivity of the grating pair’s three resonant peaks is demonstrated, and the results indicate that these grating pairs may find potential applications in optical fiber sensing.     

基于模式转换及双峰谐振效应的薄包层镀膜长周期光纤光栅特性研究

基于耦合模理论,首先研究了镀膜长周期光纤光栅(LPFG)高阶包层模的模式转换,划分了高阶包层模的非模式转换区及模式转换区。分析了高阶包层模有效折射率随薄膜厚度增加的响应特性,包层模谐振波长在模式转换区的偏移量要大于非模式转换区。在此基础上,研究了不同包层半径下高阶包层模谐振波长随光栅周期的变化情况,结果表明,相同包层半径下模式转换区内双峰间距的偏移量大于非模式转换区;无论在模式转换区还是非模式转换区,包层半径的减小将增加双峰间距的偏移量。最后分析了不同包层半径下的高阶包层模双峰透射谱在模式转换区及非模式转换区内的折射率响应,进而提出了薄包层镀膜LPFG的优化设计方案,当选定敏感膜层厚度及折射率处于镀膜LPFG的模式转换区内,光栅周期靠近相位匹配转折点时,将得到灵敏度高于传统LPFG双峰传感器的镀膜LPFG折射率型双峰传感器;而减小包层半径,将进一步提高传感器的分辨本领。     

Optimization of photonic bandgap fiber long period grating refractive-index sensors

Long period gratings in low-index contrast solid-core photonic bandgap fibers are a promising platform for fiber-based fluid refractive index sensing with very low detection limits. We provide a comprehensive investigation of the possibilities for refractive index sensing using that principle in a commercial photonic crystal fiber filled with a fluid: using an acoustic grating, we map out the cladding bands, and use this data to optimize a long period grating’s sensitivity. We then implement the optimized long period grating, again using an acoustic grating, and directly measure its sensitivity to refractive index. We demonstrate a sensitivity of 17,900 nm/RIU (6.94 nm/°C) which corresponds to a smallest detectable index change of the fluid of 8.4 × 10⁻⁶.     

长周期光纤光栅的折射率敏感特性

利用光波导的耦合模理论分析了长周期光纤光栅(LPFG)的折射率传感特性,给出了LPFG 的谐振波长相对于环境折射率变化时的漂移量解析表达式.对 LPFG 的折射率传感特性进行了数值模拟.结果表明:在光栅周期不变的情况下,当包层折射率小于且接近外界环境折射率时,波长的漂移量增大,且对应的模次越高、包层半径越小、包层折射率越小,波长漂移量越大,即 LPFG 对应于外界折射率传感灵敏度得到显著提高;当外界环境折射率大于包层折射率时,光栅的谐振波长将近似不变.     

长周期光纤光栅检测混合油的折射率

为了检测柴油煤油混合油的折射率特性,利用耦合模理论分析长周期光纤光栅折射率传感特性,建立长周期光纤光栅中心波长、透射谱峰值损耗与混合油品中柴油含量的关系.结果表明:在混合油中,随着柴油含量的增加,长周期光纤光栅波长发生蓝移,当柴油含量达到使混合油折射率等于包层折射率时,中心波长漂移最大,柴油含量每改变1%,中心波长平均漂移0.622 7nm;柴油含量继续增加,混合油折射率大于包层折射率时,光栅中心波长基本保持不变,但是峰值损耗逐渐增大,带宽减小,之后柴油含量每增加1%,峰值损耗线性增加0.154 6dB.该方法在检测混合燃料各组分含量具有潜在的应用前景.     

CO2激光脉冲边缘写入的长周期光栅折射率特性研究

报道了一种用高频CO2激光脉冲在普通通信光纤包层边缘单侧写入的新型长周期光纤光栅。研究发现,这种长周期光纤光栅的折射率变化主要发生在光纤包层区域,而纤芯的折射率变化较小;同时该光栅的附加损耗低于0.5 dB。进一步折射率特性实验研究表明,由于其特殊的折变结构,这种光栅具有较高的外界环境灵敏度,当外界折射率在1.41~1.45范围内变化时,其谐振波长漂移量高达15.52 nm,比实验测得的用传统方法写入的长周期光纤光栅谐振波长漂移量高出近3倍,这种光栅结构在光纤传感中将具有重要的应用。     

长周期光纤光栅气敏薄膜传感器结构优化

基于三包层长周期光纤光栅模型,研究了包层表面涂覆一层溶胶凝胶气敏薄膜的长周期光纤光栅化学传感器的灵敏度Sn与薄膜光学参量(折射率n3和厚度h3)和光纤光栅结构参量(光栅周期、折变量和光栅长度)之间的关系。采用最优化数值方法,找到了获得高灵敏度所需的最佳膜层光学参量和光栅结构参量。理论计算表明,该类型传感器对膜层折射率的测量分辨率高达10-8。实验上制作了对乙醇气体敏感的传感器,并证实了传感器结构优化的必要性。     

Investigation of Long Period Grating as refractive index sensor

In this paper, we have theoretically and experimentally investigated the response of Long Period Grating (LPG) as refractive index sensor. The response has been checked for the refractive index ranging from 1 to 1.458. It was found that the experimental results are very close to the theoretically simulated results. The ambient refractive index response of an LPG over a much wider index range has been modeled for values both less and more than the cladding refractive index.     

光纤纤芯及包层模有效折射率计算及仿真

光纤结构设计、模间色散求解、光纤光栅模式耦合等问题的研究, 都需要对光纤纤芯及包层模的有效折射率进行精确计算. 本文以光纤三层结构模型为基础, 结合该模型下的模式本征方程, 使用截弦法求解了纤芯模有效折射率, 并将计算结果与COMSOL软件模拟的对应纤芯模的传输光场进行对比, 验证了计算结果正确.使用区间遍历算法对包层模有效折射率进行了求解, 与已有的传统方法相比, 该方法可以有效防止求解过程中根的遗漏、避免特征方程产生的奇点, 并能保证模式的正规性.本文采用Mathematica软件对求解过程进行仿真, 获得了纤芯模和包层模有效折射率与波长关系曲线. 关键词： 光纤传输模式 有效折射率 截弦法 区间遍历算法     

Optimal design of temperature-insensitive long period fiber gratings for athermal refractive-index sensor

Based on coupled-mode theory of long-period fiber grating (LPFG), a theoretical analysis and simulations for the optimal design of a temperature-insensitive LPFG is presented in order to achieve an athermal condition for sensing the refractive index of the external medium. Effects of the variation of the cladding radius and grating period on the temperature sensitivity of the LPFG are discussed. Both of these parameters are found to be important to control the temperature sensitivity when the thermo-optic coefficients of core and cladding materials are of the same order. Other grating parameters are also optimized in order to achieve a good contrast of the grating period with resonance wavelength in the 1.5 μm region and to sense the external medium refractive index over a wide range. Variation of external medium refractive index from 1.0 to 1.45 results a red-shift in the LPFG resonance wavelength by 86 nm with its temperature sensitivity as low as 0.008 nm/°C over a temperature range of 0–80 °C for this optimally designed LPFG.     

侧面研磨光纤Bragg光栅的外部折射率敏感特性研究

光纤Bragg光栅对外界折射率的变化不灵敏,无法直接作为气体、液体等的敏感元件.侧面研磨的光纤Bragg光栅,一侧包层减小至几微米,其辐射场可通过包层透射到被传感物质,因而被传感物质的折射率的变化可以改变光纤的有效折射率,从而使光栅的Bragg波长产生位移.实验中利用不同浓度的NaCl溶液来改变光纤光栅的外部折射率,Bragg中心波长的偏移量和浓度近似为线性关系.同时,透射功率的变化量和浓度也近似为线性关系.     

Bragg gratings photoinduced in ZBLAN fibers by femtosecond pulses at 800 nm

Fiber Bragg gratings were written in thulium-doped and undoped single-mode ZBLAN fibers by focusing femtosecond laser pulses on the fiber core through a phase mask. Maximum index modulation of the order of 1 x 10(-3) was induced in both types of fibers. Measurements of the transverse refractive index changes across the core and cladding regions indicate that the grating formation originates from a negative index change.     

Design of novel DS-OCDMA encoders/decoders using phase sampled long period grating

A novel long period grating structure with phase sampled technique is proposed to act as encoders/decoders in the direct sequence optical code division multiple access (DS-OCDMA) system. The structure with address code of 31 chips is designed and the relation between the sample period, the input pulse width and the refractive index difference is given. The encoded and decoded results are demonstrated to verify the feasibility of utilizing the coupling ratio to the cladding mode. The whole structure is expected to move on the photonic crystal fiber, for it can support the large refractive index difference between the core mode and cladding mode, as well as minimize the wavelength shift caused by the temperature change.     

Theoretical and Experimental Study of Long-Period Grating Refractive Index Sensor

Abstract

This article presents the theoretical and experimental investigation of the response of long-period gratings as a refractive index sensor. Cladding modes are calculated, and results are compared with Optigrating 4.2.2 (Optiwave Systems Inc., Ottawa, Canada). The response has been checked for refractive indices ranging from 1 to 1.458. Theoretically simulated results are in accordance with the experimental results. It was found that the software package calculated values correctly up to the seventh decimal point. The ambient refractive index response of a long-period grating over a much wider index range has been modeled for values both less and more than the cladding refractive index.