复合电解质Ce0.8Gd0.2O2-α-(Li/K)2CO3的中温燃料电池性能

用溶胶凝胶法低温(900℃,通常高温烧结温度为1400℃)制备了Ce_(0.8)Gd_(0.2)O_(2-α),并与(Li/K)_2CO_3共熔体进行复合。XRD结果表明(Li/K)_2CO_3与Ce_(0.8)Gd_(0.2)O_(2-α)复合后没有发生化学反应,SEM结果表明复合电解质致密无孔洞。考察了复合电解质在400~600℃下干燥氮气气氛中的电导率,结果表明,温度为600℃时,复合电解质的电导率达到最大值6.4×10~(-2)S·cm~(-1),高于单一CeO_2材料在相同条件下的电导率。氧分压与电导率关系曲线表明复合电解质具有良好的氧离子导电性。H_2/O_2燃料电池性能测试表明,复合电解质GDC-SG-LK在600℃开路条件下的电解质阻抗、极化阻抗分别为2.7和0.8Ω,最大输出功率密度为267mW·cm~(-2)。     

La0.8Sr0.2Ga0.8Mg0.2O2.8的电化学性质及其在SOFC中的应用

采用凝胶浇注法制备具有较高氧离子电导率的固体电解质La0.8Sr0.2Ga0.8Mg0.2O2.8粉料.X射线衍射结果表明,于1400℃焙烧后即形成了钙钛矿结构,无杂相存在.探讨了粉料压制坯体的致密化和导电性能在1450℃下与烧结时间的关系,发现烧结时间为18h时其相对密度达98.3%,而在24h的情况下,样品具有最佳的氧离子导电性.采用Ni-Ce0.8Gd0.2O1.9作为阳极,La0.8Sr0.2Ga0.6Ni0.4O2.7作为阴极,组装了平板型固体氧化物燃料电池(SOFC).阳极和阴极分别通入含3%H2O的氢气和空气,750℃时的开路电压为1.04V,最大输出功率密度(P)达252mW/cm2(U=0.48V,J=525mA/cm2).     

Ce0.8Sm0.2O1.9的尿素燃烧法合成与性能

采用以尿素为燃料的燃烧合成法制备Ce0.8Sm0.2O1.9(SDC)氧离子导体材料, 对燃烧合成粉体的物相和显微形态进行了表征, 并研究了燃烧法合成SDC的烧结性能以及烧结体的导电性能. 研究结果表明, 采用尿素燃烧法合成SDC具有简便高效和合成粉体烧结活性高的优点. 经过燃烧过程后即可得到立方萤石结构的纯相SDC粉体, 合成粉体的分散性良好, 为50~150 nm的球形颗粒, 具有高的烧结活性, 在1250 ℃的烧结温度下, 陶瓷样品的相对密度可达到95.1%. 在600和800 ℃的测试温度下, 烧结温度为1250 ℃的陶瓷样品的电导率分别达到5.4×10-2和1.0×10-1 Ω-1·cm-1.     

中温固体氧化物燃料电池阴极材料LaBiMn2O6的制备与性能

采用固相法合成了中温固体氧化物燃料电池(IT-SOFCs)阴极材料LaBiMn₂O₆,并利用X射线衍射(XRD)和电化学阻抗谱(EIS)进行表征。结果表明该材料与电解质Ce_0.7Bi_0.3O_1.85(CBO)在1000℃烧结12h不发生反应。交流阻抗和直流极化测试结果发现,阴极极化电阻随测试温度的增加而逐渐减小,700℃空气中的极化电阻为0.71Ω·cm²;氧分压测试结果显示,在600~700℃范围内,电极反应的速率控制步骤为电极上发生的电荷转移反应。电极过电位为85mV时,700℃的阴极电流密度达到216mA·cm^-2,表明LaBiMn₂O₆是一种潜在的中温固体氧化物燃料电池(IT-SOFCs)阴极材料。     

新型固体氧化物燃料电池阴极材料Ca2-xSrxFe2O5的电化学性能研究

采用固相法合成了固体氧化物燃料电池(SOFC)阴极材料2-xSrxFe2O5(x=0.00,0.05,0.10,0.15,0.20),利用XRD和SEM对其结构和微观形貌进行了表征.结果表明该阴极材料与固体电解质Sm0.8Ce0.2O1.9(SDC)在1000℃烧结时不发生化学反应,且烧结4 h后,二者之间可形成良好的接触界面.利用交流阻抗谱技术对阴极材料的电化学性能进行研究,结果显示,阴极上的反应过程主要为电荷的迁移反应,其中Ca1.95Sr0.05Fe2O5电极在空气中700℃下具有最小的极化电阻为0.95Ω·cm2.当测试温度为700℃时,阴极电流密度为74mA·cm-2时,阴极过电位为100mV.     

泡沫镍负载Fe2O3@Ni3S2纳米线网状结构电极的制备及其电催化析氧性能

通过两步水热法制备泡沫镍(NF)负载Fe_2O_3纳米粒子@Ni_3S_2纳米线网状结构电极(Fe_2O_3@Ni_3S_2/NF)。运用X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、N_2吸附-脱附测试等方法对电极材料的物相和微观结构特征等进行了表征。水热条件下原位表面化学刻蚀生成的Ni_3S_2纳米线与三维多孔NF基体间拥有强结合力和低界面电阻,Fe_2O_3粒子均匀分布在纳米线的表面。在1 mol·L~(-1)的KOH溶液中,运用线性扫描伏安测试(LSV)、计时电位法、电化学交流阻抗测试(EIS)等对电极的电催化析氧(OER)性能进行了测试。结果表明:在100 mA·cm~(-2)的超高电流密度下,Fe_2O_3@Ni_3S_2/NF电极的OER过电势仅为223 mV,比Ni_3S_2/NF材料的过电势降低了285 mV;经过10 h计时电位测试,性能保持率高达80%。     

(Pr0.9La0.1)2(Ni0.74Cu0.21Ga0.05)O4+δ纳米纤维阴极的制备及电化学性质

采用静电纺丝法制备了(Pr_(0.9)La_(0.1))_2(Ni_(0.74)Cu_(0.21)Ga_(0.05))O_(4+δ)(PLNCG)氧化物纳米纤维。利用热重-差热分析(TG-DTA)、X射线衍射(XRD)、傅里叶变换红外光谱(FT-IR)和扫描电子显微镜(SEM)对材料的物相及微观形貌进行分析。研究表明950℃煅烧5 h得到平均直径420 nm、形貌均一的PLNCG氧化物纤维;1 000℃烧结2 h得到紧密附着在Ce_(0.9)Gd_(0.1)O_(2-δ)(CGO)电解质上的网状结构纤维阴极。电化学阻抗谱(EIS)测试结果表明纳米纤维阴极具有比粉体阴极更优越的性能。700℃的极化电阻(RP)为0.134Ω·cm~2,比同组分的粉末阴极减少32%(RP=0.197Ω·cm~2)。以纤维阴极构筑的电解质支撑单电池Ni-CGO/CGO/PLNCG在700℃的最大输出功率密度为231 m W·cm-2。氧分压测试结果表明阴极反应的速率控制步骤为电荷转移过程。     

掺F影响LiNi0.8Co0.1Mn0.1O2结构和性能的微观机制

以氟化锂为氟源,通过高温固相法合成了F掺杂的LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2。采用X射线衍射仪(XRD)、扫描电镜(SEM)、X射线光电子能谱(XPS)和电化学测试等手段研究F影响LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2结构和性能的微观机制。结果表明:适量F掺杂可以提高正极材料的放电比容量,改善其倍率性、循环性和热稳定性。当F掺杂量(物质的量分数)为1.5%时,材料的综合电化学性能最优,初始放电比容量(0.2C)和50周循环容量保持率(1C)分别由原始的174.0 mAh·g~(-1)(78.7%)提高到178.6 mAh·g~(-1)(85.7%)。LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2材料性能的改善可归因于F能够增强过渡金属层、锂层与氧层之间的结合力,提高材料的结构稳定性。此外,F掺杂还有利于降低电化学反应中的界面电阻和电荷转移阻抗。     

石墨烯修饰改性制备锂离子电池LiFePO4/LiNi0.8Co0.15Al0.05O2复合正极材料及其性能

采用两步干混-球磨方法制备了石墨烯掺杂改性的锂离子电池LiFePO_4/LiNi_(0.8)Co_(0.15)Al_(0.05)O_2复合正极材料,实现LiNi_(0.8)Co_(0.15)Al_(0.05)O_2材料的高容量和高安全性。借助X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、X射线光电子能谱(XPS)以及电化学测试等表征手段对材料的晶体结构、微观形貌和电化学性能进行了较系统的研究。结果表明,石墨烯的存在实现了Li Fe PO4材料在LiNi_(0.8)Co_(0.15)Al_(0.05)O_2材料表面的完全包覆,形成致密的包覆层,进一步抑制LiNi_(0.8)Co_(0.15)Al_(0.05)O_2与电解液之间的副反应,提高活性材料利用率和循环性能。三者之间构成导电网络,加快电子渗透和传输,提高倍率性能。Li Fe PO4质量分数为20%的Li Fe PO4-Graphene/LiNi_(0.8)Co_(0.15)Al_(0.05)O_2样品具有最佳的容量性能和长循环性能,0.1C时放电容量达到202.5 m Ah·g~(-1),3C时放电容量仍然可保持在160.5 m Ah·g~(-1)。50℃在2.8~4.3 V,0.5C下循环100次后,容量保持率为91.9%,优于LiNi_(0.8)Co_(0.15)Al_(0.05)O_2和LiFePO_4/LiNi_(0.8)Co_(0.15)Al_(0.05)O_2样品的72.9%和82.0%。     

微球LiNi0.8Co0.1Mn0.1O2材料的制备及在改性电解液中的电化学性能

利用共沉淀辅以高温烧结法制备了椭球形三元高镍LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2(LNCM811)正极材料,并用XRD、SEM和TEM对其结构和形貌进行表征。利用CV和恒流充放电测试LNCM811在添加质量含量分别为2%(w/w)DTD(硫酸乙烯酯)、1%(w/w)MMDS(甲烷二磺酸亚甲酯)及其复合添加剂2%DTD+1%MMDS的电解液中的电化学性能,并利用EIS测试其充放电过程中的动力学特性。结果发现相较于1%MMDS,2%DTD能较为显著提高LNCM811在常温的首周放电容量和首周库伦效率;1%MMDS和2%DTD均能提高电极材料的长循环寿命,室温25℃条件下2%DTD比1%MMDS效果更显著,而高温60℃下1%MMDS比2%DTD更为明显;LNCM811正极无论在室温下还是高温下在复合添加剂的电解液中均具有最好循环性能。EIS测试表明2%DTD+1%MMDS复合添加剂能显著降低LNCM811动力学阻抗。     

一维纳米Co_3O_4,Ag/Co_3O_4及CuO/Co_3O_4的合成与电催化性能(英文)

采用水热合成法制备了Co3O4及复合Ag/Co3O4、CuO/Co3O4一维纳米产品。用XRD,FE-SEM和TEM手段对产品进行了表征。采用循环伏安法研究了合成产品修饰的玻碳电极在碱性溶液中对对硝基苯酚的电催化还原性能。与裸玻碳电极相比,1mmol·L-1的对硝基苯酚在用Co3O4、特别是CuO/Co3O4修饰的玻碳电极上还原的峰电流明显增大,用Ag/Co3O4(Ag/Co原子比分别为1∶5和2∶5)修饰的玻碳电极催化还原对硝基苯酚时,尽管还原峰电流增大不是太大,但其峰电位明显降低(分别降低0.265和0.371V)。     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃‐Bi₂O₃‐ZnO‐Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1364,介电损耗低至1.2%。     

Magnetic diphase nanostructure of ZnFe2O4/γ-Fe2O3

Magnetic diphase nanostructures of ZnFe₂O₄/γ-Fe₂O₃ were synthesized by a solvothermal method. The formation reactions were optimized by tuning the initial molar ratios of Fe/Zn. All samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, and Raman spectra. It is found that when the initial molar ratio of Fe/Zn is larger than 2, a diphase magnetic nanostructure of ZnFe₂O₄/γ-Fe₂O₃ was formed, in which the presence of ZnFe₂O₄ enhanced the thermal stability of γ-Fe₂O₃. Further increasing the initial molar ratio of Fe/Zn larger than 6 destabilized the diphase nanostructure and yielded traces of secondary phase α-Fe₂O₃. The grain surfaces of diphase nanostructure exhibited a spin-glass-like structure. At room temperature, all diphase nanostructures are superparamagnetic with saturation magnetization being increased with γ-Fe₂O₃ content.     

MgAl2O4尖晶石对锂离子电池正极材料LiMn2O4的循环性能影响研究

MgAl₂O₄ spinel doping into cathode materials LiMn₂O₄ was used to improve the cyclic performance of the cathode. X-ray analysis results showed, when MgAl₂O₄ precursors were mixed with LiMn₂O₄ and sintered at 770 ℃ for 12 hour, MgAl₂O₄-LiMn₂O₄ mulriple spinel with the same physical characteristics as pure LiMn₂O₄ were synthesized. The electro-chemical performance testing showed, comparing with pure LiMn₂O₄, the first charge-discharge capacity of doping materials somewhat reduced, but the cyclic performance improved. The mechanism for doping material was also discussed.     

A simple conversion of azlactones into indenones via H3PW12O40/Al2O3 catalyzed intramolecular Friedel-Crafts reaction

A rapid and simple procedure for the synthesis of the indenone derivatives, N-(1-oxo-1H-inden-2-yl)benzamides, via intramolecular Friedel-Crafts (IFC) reaction of (Z)-4-arylidene-2-phenyl-5(4)-oxazolones (azlactones) catalyzed by H₃PW₁₂O₄₀ supported on neutral alumina under microwave irradiation has been developed. The reaction is straightforward and allows easy isolation of the product. The catalyst could be re-used up to four times after simple filtration.     

BaO-Al2O3-B2O3系密封玻璃的结构与性质

The BaO-Al₂O₃-B₂O₃ glasses manufactured for solid oxide fuel cell(SOFC) sealing were studied. The effect of different n_BaO/n_B2O3 on crystal, thermal properties, density and infrared spectra of this system has been discussed. The results show that the trends of crystallization, glass transformation temperature, dilatometric softening temperature and density increase with n_BaO/n_B2O3 values. But a typical property deviation occurs when n_BaO/n_B2O3 is 0.875, and its coefficient of thermal expansion has the maximum at this point. The changes of properties can attribute to the conversion of boron from tetrahedral coordination to trigonal, breakage of the local glass network and interaction between the network modifiers. These can be proved by infrared spectra of glasses. Thermal properties of some studied samples are suitable for the sealing of SOFC using Sm doped ceria electrolyte and operating at 400～600 ℃.     

Structure and magnetism of NaRu2O4 and Na2.7Ru4O9

The structures of NaRu₂O₄ and Na_2.7Ru₄O₉ are refined using neutron diffraction. NaRu₂O₄ is a stoichiometric compound consisting of double chains of edge sharing RuO₆ octahedra. Na_2.7Ru₄O₉ is a non-stoichiometric compound with partial occupancy of the Na sublattice. The structure is a mixture of single, double and triple chains of edge-shared RuO₆ octahedra. NaRu₂O₄ displays temperature independent paramagnetism with . Na_2.7Ru₄O₉ is paramagnetic, χ₀= with and a Curie constant of 0.0119 emu/mol Oe K. Specific heat measurements reveal a small upturn at low temperatures, similar to the upturn observed in La₄Ru₆O₁₉. The electronic contribution to the specific heat (γ) for Na_2.7Ru₄O₉ was determined to be15 mJ/mole_Ru K².     

MgFe2O4-Fe2O3纳米粉体的软化学合成及电磁学特性

Nano-MgFe₂O₄-Fe₂O₃ magnetic powders were synthesized by citrate gel under microwave irradiation. The structure，particle size distribution，electromagnetic characteristics of nano-MgFe₂O₄-Fe₂O₃ were characterized by using TG-DTA, X-ray, electronic microscope, nano-size measurement and electromagnetism measurement apparatus。The results show that the product is a mixture of MgFe₂O₄ and Fe₂O₃ with average size of 44 nm, tanδ for the product is 0.265 and 0.610 at frequency of 1.0 GHz and 1.8 GHz respectively.     

The Al2O3-Fe2O3 Mixed Oxidic System, I. Preparation and Characterization

A series of Al₂O₃-Fe₂O₃ mixed oxidic solids with composition ranging from 0 to 100% of Fe₂O₃ were prepared and examined for structural characteristics. XRD diagrams showed the presence of α-Al₂O₃ and hematite phases. The analysis of M?ssbauer spectra revealed the existence of two iron containing phases. The specific surface area of the mixture decreases by the addition of iron and depends on the crystal phases of the mixture. This revised version was published online in June 2006 with corrections to the Cover Date.