光子晶体中缺陷的色散导致的群速度降低

利用传输矩阵方法计算了包含色散媒质缺陷的一维光子晶体的复透射系数，其中色散媒质用洛仑兹振子模型描述。计算了由复透射系数定义的等效复折射率并由此研究了频谱位于缺陷模频率附近的光脉冲的群速度。结果发现，由于缺陷模附近的透射谱敏感地依赖于缺陷层的光学厚度，而缺陷层的色散使缺陷层光学厚度随频率变化而改变，从而使包含缺陷的光子晶体的等效色散性质明显地依赖于缺陷的色散行为。由于光脉冲是由多种频率成分的单色场迭加构成的，透射脉冲由各单色场透射后重新迭加构成，因此波包的传播由介质的等效色散性质决定。与包含无色散缺陷的光子晶体相比，缺陷的色散可导致极慢的群速度。通过改变振子强度，群速度可从极慢光速转变为超光速(superluminal)。     

含具有双增益线原子的光子晶体中的光传播

讨论了缺陷层包含具有双增益线的原子的一维光子晶体中的色散效应及透射谱，双增益线间出现了反常色散区，由于入射光与双增益线的相互作用使得光子带隙中出现了两个透射率远大于1的透射峰；透射峰随着缺陷位置和体系结构参数的变化而产生变化；左透射峰和右透射峰很窄的频率范围内分别出现了斜率极大的反常色散和正常色散，产生了负的群速度和极慢光速的光传播行为。     

一维对称光子晶体的简正耦合模

对一维对称光子晶体中的色散介质采用洛仑兹振子模型,通过考虑色散介质层两侧的边界条件,得到了表征色散介质层的转移矩阵.对线性层及色散δ层均采用传输矩阵的方法,研究了一维含色散介质的光子晶体微腔中的简正耦合模.由于光与色散介质的相互作用,纵腔模将分裂成简正耦合模.通过改变色散介质的相关参数,详细研究了简正耦合模频率的移动、均匀展宽效应和失谐效应.发现两个简正的耦合模的频率间距主要依赖于振子的耦合强度,与约化的振子的HWHM线宽无关.失谐效应则会使其中的一个峰降低,而另一个峰相对拉高,这一现象可以通过Fabry-Pérot腔得到很好的解释.     

带有增益的单微环谐振器的光速控制行为

带有损耗的光波导微环谐振器在实现光速控制时存在输出脉冲能量损耗大、脉冲形状畸变严重等问题。基于带有增益和带有损耗的微环谐振器的传输特性之间的对称性,计算分析了单微环谐振器的透射率、群折射率和群速度色散等特性,分析了增益和损耗对微环谐振器输出特性影响的机制。计算了带有增益的微环谐振器的光速控制行为,并与带有损耗的微环谐振器进行对比。结果显示,带有增益的微环谐振器输出脉冲不分裂且有较大的输出强度。脉冲延迟量和超前量比损耗系统大,可用于光速控制,克服了微环带有损耗时产生的光强损耗和脉冲畸变。     

光脉冲在一维负折射材料光子晶体中的传播

讨论了一维负折射光子晶体对光脉冲传播的影响.通过对光脉冲的透射场强的数值计算发现,频谱处于一维负折射率材料光子晶体禁带中的短脉冲通过光子晶体后基本保持形状不变,而对同样的短脉冲通过传统的一维光子晶体的透射脉冲则出现严重畸变.当考虑负折射率材料的色散时,讨论了位相时间随光脉冲载波频率的变化情况.     

双折射光子晶体光纤中基于孤子分裂的超连续光谱产生

利用亚纳焦量级、脉冲宽度为100 fs的激光脉冲在双折射光子晶体光纤中获得了450—1050 nm 的超连续光谱,且超连续光谱具有明显的分立峰状结构.分析了光谱中分立峰状结构产生的物理机制,抽运光波长处于接近零色散波长的反常色散区,形成高阶光孤子,由于高阶非线性和高阶色散的影响,高阶孤子分裂成多个基孤子,使初始光谱上演化出红移的光孤子成分和蓝移的色散波成分.理论模拟了飞秒激光脉冲在光纤中的色散特性和传输特性,较好地解释了实验结果. 关键词： 光子晶体光纤 超连续光谱产生 孤子分裂 脉冲俘获     

含色散介质的一维光子晶体微腔中简正耦合模的物理图像

对一维光子晶体中的色散介质采用洛伦兹振子模型,对线性层及色散δ层均采用传输矩阵的方法,研究了一维含色散介质的光子晶体微腔中的简正耦合模.通过改变洛伦兹振子和微腔之间的失谐频率,分析了简正耦合模频率的变化情况.在失谐频率比较大时,光与洛仑兹振子间的耦合作用较小,简正耦合模中的一个接近腔模频率,而另一个则接近洛仑兹振子的共振频率;在失谐频率比较小时,光与洛仑兹振子间的耦合作用较大,简正耦合模与未耦合的腔模频率和洛仑兹振子的共振频率之间的差别较为明显.最后通过引进该结构的复有效折射率,对含色散介质的系统,由于带隙中间的共振模被湮灭并分裂为左右两个耦合模,其复有效折射率虚部在原共振峰处跃变为一较大值,而在新生成的两个耦合模附近趋近于零,光与色散介质相互耦合而形成的腔极化激元的物理图像十分清晰.     

电子学领域的群速超光速实验

研究了电信号在阻抗周期失配的光子晶体结构中的群速超光速传播问题,构建了一种具有周期失配性的结构,此种阻抗失配引起非正常色散以及在8 MHz附近出现禁带.正弦调幅信号和窄脉冲信号分别被送入两种超光速实验装置. 实验结果表明,正弦调幅信号在禁带出现群速超光速,群速最大可达到3.52倍光速,而窄脉冲信号始终以正常速度传播.     

超光速群速度与信息传输的有效速度

研究了反常色散介质中脉冲形变对超光速群速度的影响,发现即使光脉冲完全不产生形变群速度仍会超过真空中的光速。但波包的群速度并不等同于信号的传输速度,采用信息论方法,定义了信号的有效传输速度,并用于解释WKD(Wang,Kuzmich,Dogariu)实验。通过计算入射光与出射光信号所携带的信息量,发现由于光的波动衍射及光子散粒噪声的影响,出射光所携带的信息量会损失,使得光信号的有效传播速度不会超过真空中的光速。     

一维缺陷光子晶体温度的测量

采用Si和SiO₂两种介质材料构造一维缺陷光子晶体，缺陷层介质为Si，利用传输矩阵法对带有缺陷的一维光子晶体的传光特性进行了理论分析，并得到其带隙特性.由于缺陷的存在，使得光子晶体的透射谱中产生缺陷峰.当被测温度变化时，根据两种介质的热光效应和热膨胀效应，光子晶体介质和缺陷层的光学厚度和折射率发生变化，透射谱缺陷峰产生漂移，由缺陷峰的中心波长漂移量得到被测温度的大小.构建了一维缺陷光子晶体测量温度的实验系统，实验结果表明缺陷峰中心波长与光子晶体所受的温度呈线性关系，测量灵敏度为0—2     

47 W, 6 ns constant pulse duration, high-repetition-rate cavity-dumped Q-switched TEM(00) Nd:YVO(4) oscillator

We report on a cavity-dumped Q-switched TEM(00) Nd:YVO(4) oscillator offering a unique combination of high power, constant short pulse duration, and high repetition rate, suppressing the gain dependence of pulse duration in classical Q-switched oscillators. Its performance is compared with that of the same oscillator operated in a classical Q-switched regime, demonstrating the much higher peak powers achievable with this technique, especially at high repetition rates. Up to 31 W of 532 nm green light was generated by frequency doubling in a noncritical phase matched LBO crystal, corresponding to 70% conversion efficiency.     

High power all-fibered femtosecond master oscillator power amplifier at 1.56 μm

Direct amplification of output from chirped pulse oscillator (CPO) to 3.3?W of average power (pulse energy of 118?nJ in 20?ps pulse duration before compression) was achieved in a properly designed cladding pumped large mode area Er-doped fiber. Various configurations of CPO cavity with different FWHM of output spectrum and pulse duration were investigated. Fourier limit compression with 480?fs pulse duration and 32?kW peak power has been obtained for pulses with 14.8?nm FWHM spectrum. Subsequent nonlinear compression in a standard SMF-28 fiber yielded pulses as short as 145?fs.     

Experimental and Theoretical Study of the Generation and Non-Linear Conversion of Picosecond Bursts from an Amplified Ytterbium-Doped Fiber Laser System

Abstract

This article presents an experimental and theoretical study of the generation of picosecond bursts by a non-polarization-maintaining ytterbium-doped fiber master oscillator fiber amplifier system. The peak power and pulse energy of the burst are higher than 45 kW and 350 nJ at 700 kHz, respectively. The master oscillator fiber amplifier was used to generate 3 W of green and 200 mW of UV light with conversion efficiencies of 16% and 8%, respectively. The enhancement of conversion efficiency by the pulse burst compared with regular pulses was analyzed and attributed to dynamically saturated gain of the pump-power-limited fiber amplifier.     

Separation of label and payload using FP-SOA

A novel scheme of separating the label and payload with different pulse width by using FP-SOA is proposed in this paper. Due to the facet reflectivity of FP-SOA, the gain is rippled with the variation of carrier density and the opposite characteristics of gain and carrier density appear at either side of the gain peak. Since the different pulse widths deplete different number of carriers, the working region in carrier density shifts adaptively with the pulse width. The wide pulse label extraction can be performed in the region where the gain decreases with the increment of carrier density. The label suppression can be realized in another region where the gain increases with increment of carrier density. The numerical simulation shows that the label extraction with 10.5 dB contrast ratio and the label suppression with 7 dB. The application in 10 Gb/s optical packet switching is discussed. The relationship of the pulse peak gain and pulse width is investigated on considering the impact of the pulse peak power and pulse period.     

脉冲形状对脉冲经光纤放大器传输后功率增益的影响

基于描述脉冲放大过程的时间相关非线性辐射迁移方程,对不同形状脉冲经掺镱光纤放大器传输后的功率特性进行了分析,该方程同时考虑了光与介质的相互作用.数值结果表明,在相同的脉冲能量下,不同形状脉冲经放大器放大后的功率增益随入射脉冲形状不同而不同,并且功率增益的差异在脉冲前沿比较大.这使得放大器输出脉冲峰值向前沿的偏移量以及峰值功率的放大倍数都与脉冲形状有关.尤其是当入射脉冲的能量较大时,不同形状脉冲的峰值功率的放大倍数明显不同,以超高斯脉冲为最大,高斯脉冲、双曲正割脉冲次之,洛伦兹脉冲最小.     

Injection-Seeded 500 Hz Repetition Rate High Peak Power Single-Frequency Nd:YAG Laser for Mid-Infrared Generation

We develop an injection-seeded single-frequency neodymium-doped yttrium aluminum garnet (Nd:YAG) laser with 500 Hz repetition rate and high peak power. The laser construction is designed as seed injection and master oscillator power amplifier (MOPA) including single-frequency master oscillator, extra-cavity frequency doubling crystal, and round-trip power amplifier. The master oscillator can emit 1,064 nm laser of 8.4 mJ with 6.8 ns pulse width at the pump energy equal to 23 mJ. A green laser energy of 1.1 mJ is obtained by setting the proper temperature of the LBO crystal. The pulse energy of 1,064 nm laser decreases to 6.5 mJ after passing through the LBO crystal and rises to 25.3 mJ after a round-trip power amplifier corresponding to the extraction efficiency of 29%. The final output pulse width is 6.5 ns, representing a peak power of 3.9 MW. The 1,064 nm laser beam quality factor M² of the master oscillator and the amplified one are 1.3 and 1.5, respectively. The laser will be used to generate mid-infrared where the 532 nm laser with narrow pulse width is to pump sheet optical parametric oscillator (OPO) and the 1,064 nm laser with high peak power to pump the OPO.     

High-power ultrafast thin disk laser oscillators and their potential for sub-100-femtosecond pulse generation

Ultrafast thin disk laser oscillators achieve the highest average output powers and pulse energies of any mode-locked laser oscillator technology. The thin disk concept avoids thermal problems occurring in conventional high-power rod or slab lasers and enables high-power TEM₀₀ operation with broadband gain materials. Stable and self-starting passive pulse formation is achieved with semiconductor saturable absorber mirrors (SESAMs). The key components of ultrafast thin disk lasers, such as gain material, SESAM, and dispersive cavity mirrors, are all used in reflection. This is an advantage for the generation of ultrashort pulses with excellent temporal, spectral, and spatial properties because the pulses are not affected by large nonlinearities in the oscillator. Output powers close to 100 W and pulse energies above 10 μJ are directly obtained without any additional amplification, which makes these lasers interesting for a growing number of industrial and scientific applications such as material processing or driving experiments in high-field science. Ultrafast thin disk lasers are based on a power-scalable concept, and substantially higher power levels appear feasible. However, both the highest power levels and pulse energies are currently only achieved with Yb:YAG as the gain material, which limits the gain bandwidth and therefore the achievable pulse duration to 700 to 800 fs in efficient thin disk operation. Other Yb-doped gain materials exhibit a larger gain bandwidth and support shorter pulse durations. It is important to evaluate their suitability for power scaling in the thin disk laser geometry. In this paper, we review the development of ultrafast thin disk lasers with shorter pulse durations. We discuss the requirements on the gain materials and compare different Yb-doped host materials. The recently developed sesquioxide materials are particularly promising as they enabled the highest optical-to-optical efficiency (43%) and shortest pulse duration (227 fs) ever achieved with a mode-locked thin disk laser.     

基于超辐射机理产生X波段高功率亚纳秒脉冲研究

设计了一种基于超辐射机理的X波段相对论返波管结构, 利用全电磁2.5维粒子模拟程序对返波管中的超辐射机理进行了粒子模拟研究. 模拟表明: 在束430kV、束流4kA, 脉宽3.1ns的电子束驱动下,实现了峰值功率1.5GW、频率10GHz、脉宽500ps的亚纳秒微波脉冲输出, 峰值功率转换效率达到87.2%;在超辐射机理作用下, 微波峰值功率与电子束脉宽在一定的范围内成平方关系.     

Doping management for high-power fiber lasers: 100 W, few-picosecond pulse generation from an all-fiber-integrated amplifier

Thermal effects, which limit the average power, can be minimized by using low-doped, longer gain fibers, whereas the presence of nonlinear effects requires use of high-doped, shorter fibers to maximize the peak power. We propose the use of varying doping levels along the gain fiber to circumvent these opposing requirements. By analogy to dispersion management and nonlinearity management, we refer to this scheme as doping management. As a practical first implementation, we report on the development of a fiber laser-amplifier system, the last stage of which has a hybrid gain fiber composed of high-doped and low-doped Yb fibers. The amplifier generates 100?W at 100?MHz with pulse energy of 1 μJ. The seed source is a passively mode-locked fiber oscillator operating in the all-normal-dispersion regime. The amplifier comprises three stages, which are all-fiber-integrated, delivering 13?ps pulses at full power. By optionally placing a grating compressor after the first stage amplifier, chirp of the seed pulses can be controlled, which allows an extra degree of freedom in the interplay between dispersion and self-phase modulation. This way, the laser delivers 4.5?ps pulses with ～200 kW peak power directly from fiber, without using external pulse compression.