FBG filter with minimal dispersion

An optimal filter for super-fast fiber-optic communication lines should cause minimal phase distortions. The simplest case of Bragg grating with a symmetric profile is considered. A distortion functional is presented, which is the mean square group delay over the Bragg reflection band at a fixed integral reflectivity. The functional is minimized analytically in the simplest limiting case. Numerical calculations confirm that the optimal reflection spectrum is realizable.     

Measuring the group delay of fiber Bragg gratings by use of end-reflection interference

A new, simple method for characterization of fiber Bragg gratings is proposed. The group delay of the grating is obtained from measurement of the spectral reflectivity response of a grating that is interfering with a bare-fiber end reflection.     

非对称切趾对啁啾光纤光栅特性优化的分析

基于对啁啾光纤布拉格光栅反射谱和时延曲线的分析,引入非对称切趾技术。综合时延曲线纹波和反射谱纹波平滑两方面考虑,将对称切趾技术的最佳切趾比例、左移和右移两种非对称切趾技术以及采用不同切趾函数对光纤光栅特性参量的优化效果进行了分析和比较。结果表明,与对称切趾相比,左移非对称切趾可避免对称切趾中为增大反射谱带宽而减小切趾比例使时延纹波增大的缺点,在保持反射谱纹波基本不变的前提下将时延曲线纹波降低了43.5%(与实验结果39.9%相吻合)。此外,与仅用汉明函数切趾相比,光纤光栅左端采用超高斯函数、右端采用汉明函数的非对称切趾方式使反射谱平坦部分纹波减小了89.3%,对应的时延曲线拟合误差减小了16.7%,获得了更好的优化效果。     

Design of a flat-top fiber Bragg filter via quasi-random modulation of the refractive index

The statistics of the reflection spectrum of a short-correlated disordered fiber Bragg grating are studied. The averaged spectrum appears to be flat inside the bandgap and has significantly suppressed sidelobes compared to the uniform grating of the same bandwidth. This is due to the Anderson localization of the modes of a disordered grating. This observation prompts a new algorithm for designing passband reflection gratings. Using the stochastic invariant imbedding approach it is possible to obtain the probability distribution function for the random reflection coefficient inside the bandgap and obtain both the variance of the averaged reflectivity as well as the distribution of the time delay of the grating.     

低纹波系数色散补偿光纤光栅的研究

介绍用扫描法研制成功的长13．5cm、带宽0．447nm、反射谱平坦的切趾啁啾光纤光栅，功率波动小于1dB，用色散分析仪测试得到时延曲线上的纹波系数小于20ps，用该光纤光栅对200km的G．652光行色散补偿，补偿量大于98％（原始脉冲宽度为36．78ps，色散补偿后的脉冲宽度为37．23ps）。     

Improving the performance of chirped fiber grating with cladding being etched as sinusoidal function

A new grating structure of cladding being etched as sinusoidal function along the grating length is introduced to improve their performance. When a tension is applied to it, the fiber grating not only exhibits a flattop spectrum with steep edges and high reflectivity, but also has a smoothly time delay curve. The bandwidth utilization defined as the ratio of −1:−30 could be achieved a larger value (>0.90). The −3 dB bandwidth and the bandwidth utilization could be tunable with the increment of tension applied to the grating and the linearly chirped modulus.     

Analytical performance evaluation of an adjustable PMD compensator using high-birefringence linearly chirped FBG

System performance of a high-speed WDM transmission system in the presence of PMD can be improved significantly by using an adjustable PMD compensator. We have analytically evaluated the performance of a tunable PMD compensator based on high-birefringence linearly chirped fiber Bragg grating. The device can adjust differential group delay in a linearly continuous way without affecting the wavelength outside the bandwidth. Various properties of the device such as relative group delay, differential group delay, reflectivity, etc. are investigated in terms of wavelength and grating length. Results show that under stretched condition the device generates a time delay between fast and slow polarization axes, which is adjustable from 0 to 55 ps and is tunable within 2.4 nm wavelength range.     

Distributed Bragg grating sensing with a direct group-delay measurement technique

A new method of distributed in-fiber Bragg grating sensing is proposed. A method is outlined by which the strain field imposed upon a Bragg grating sensor is obtained by measurement of the sensor's reflectivity and delay characteristics. The proposal is demonstrated by interrogation of two loaded samples. Strain distributions from these experiments are compared against a theoretical estimate. The data treatment is also discussed. Strain resolution is found to be +/-24 microepsilon, with a spatial resolution defined by a minimum spatial wavelength component of the coupling distribution of 1.65 mm.     

基于亚波长光栅的VCSEL偏振控制研究

为了确定亚波长光栅在微电机械系统(MEMS)波长可调谐VCSEL不同位置(上DBR上表面、上DBR下表面以及内腔)中实现TE和TM偏振控制的光栅参数范围以及光栅在哪个位置时实现偏振控制最稳定,通过MATLAB建立MEMS波长可调VCSEL的模型,然后计算光栅在3种位置时上反射镜(包括空气隙和光栅)随光栅参数变化的反射率,以此来确定它们实现TE/TM稳定偏振的光栅参数范围(即高反射范围内的参数)。将各自的高反射所对应反射率减去相同光栅参数范围内TM/TE低反射对应的反射率,通过反射率差值确定光栅在哪种位置时MEMS波长可调谐VCSEL实现偏振是最稳定的。最后得出的结论是光栅在上DBR下表面几乎无法控制TM偏振,而将光栅放置于内腔中,无论是在TE偏振控制上还是TM偏振上都是最稳定的。在实现TE偏振稳定的参数范围内,TE的阈值增益比TM最小少10 cm~(-1);而在实现TM偏振稳定时,在TE偏振稳定的参数范围内,TE的阈值增益比TM最小少5 cm~(-1)。     

Frequency Downconverting Fiber Grating-Based Beamformers for High-Capacity Phased Arrays

A technique is presented to remove the beat noise limitation in multibeam beam formers using a simple all-optical microwave frequency downconversion technique prior to performing the true-time delay equalization in the optical domain. The frequency conversion concept enables a significant increase in beam-number capac ity to be achieved due to the elimination of beat noise limits, and also effectively removes the power penalty due to chromatic dispersion limitations of the chirped grating units in the beamformer. The Bragg grating requirements for the frequency converting beamforming network are analyzed and show that tanh-profile apodized gratings can meet the isolation, reflectivity, and narrow bandwidth requirements. For an X-band phased array, more than a twofold increase in beam capacity is shown through the use of the frequency conversion technique with the grating-based beamformer, and the resulting beamformer has the minimum number of optical interconnects with true-time delay operation.     

Frequency Downconverting Fiber Grating-Based Beamformers for High-Capacity Phased Arrays

A technique is presented to remove the beat noise limitation in multibeam beam formers using a simple all-optical microwave frequency downconversion technique prior to performing the true-time delay equalization in the optical domain. The frequency conversion concept enables a significant increase in beam-number capac ity to be achieved due to the elimination of beat noise limits, and also effectively removes the power penalty due to chromatic dispersion limitations of the chirped grating units in the beamformer. The Bragg grating requirements for the frequency converting beamforming network are analyzed and show that tanh-profile apodized gratings can meet the isolation, reflectivity, and narrow bandwidth requirements. For an X-band phased array, more than a twofold increase in beam capacity is shown through the use of the frequency conversion technique with the grating-based beamformer, and the resulting beamformer has the minimum number of optical interconnects with true-time delay operation.     

Tunable photonic delay lines in optical fibers

A comprehensive overview is presented about optical fiber‐based tunable photonic delay lines, which have been steadily developed over the last decade for the realization of all‐optically controlled timing functions. The most widely used techniques, such as those based on slow & fast light and wavelength conversion associated to dispersion, are described and their physical limitations are discussed in terms of the maximal achievable delay, the associated signal distortion and signal bandwidth. Besides, an entirely different approach for all‐optical signal delaying is introduced. This technique is based on movable grating reflectors dynamically generated in highly birefringent optical fibers. This type of delay line has experimentally demonstrated large tunable delaying with a moderate signal distortion for high capacity optical data streams and even for wideband analog signals.     

极窄带宽的布拉格光纤光栅光谱特性研究

根据理想模展开下的耦合模方程，对光纤布拉格光栅的峰值反射率公式进行了数学推导，得到了布拉格光纤光栅的光谱反射率表达式。全面讨论了光栅周期、光纤栅长、光致折射率微扰最大值等参数与光纤光栅反射光谱的关系。仿真结果显示了固定参数下布拉格光栅的极限窄带宽，得到的反射率为1、带宽为0.02nm的窄带宽布拉格光栅，比现今分布式传感系统中使用的布拉格光栅的带宽窄1个数量级。这种布拉格光纤光栅用于分布式传感系统，可大大提高分布式传感系统中光源的带宽利用率，消除各信号间的相互串扰，提高传感光栅复用数目，降低解调系统成本。     

倾斜光纤光栅谱特性

基于倾斜光纤光栅耦合模理论,采用数值分析法研究了前后向导模耦合时倾斜角度和调制深度对倾斜光纤光栅反射谱的影响,以及导模和辐射模耦合时针对不同的入射光偏振态在倾斜角度、调制深度、光栅长度等不同时倾斜光纤光栅透射谱(或反射谱)的特性.研究结果表明,在前后向导模耦合时,不同偏振态入射光的光谱几乎相同;而对于辐射模耦合,由于反射谱的包络受消光系数的调制,而不同偏振态入射光的消光系数不同,并且倾斜角度越大不同偏振态的入射光的消光系数差别越大,故在研究辐射模耦合时需要将偏振态予以考虑.     

倾斜光纤光栅谱特性

基于倾斜光纤光栅耦合模理论,采用数值分析法研究了前后向导模耦合时倾斜角度和调制深度对倾斜光纤光栅反射谱的影响,以及导模和辐射模耦合时针对不同的入射光偏振态在倾斜角度、调制深度、光栅长度等不同时倾斜光纤光栅透射谱(或反射谱)的特性.研究结果表明,在前后向导模耦合时,不同偏振态入射光的光谱几乎相同;而对于辐射模耦合,由于反射谱的包络受消光系数的调制,而不同偏振态入射光的消光系数不同,并且倾斜角度越大不同偏振态的入射光的消光系数差别越大,故在研究辐射模耦合时需要将偏振态予以考虑.     

Fabrication of high quality chirped fiber Bragg grating by establishing strain gradient

To fabricate chirped fiber Bragg grating (CFBG) with high reflectivity and accurately controlled chirp profile with low cost, we develop the CFBG fabrication technique based on strain gradient: fabricating CFBG using fabricated fiber Bragg grating (FBG) by establishing strain gradient along the length of grating. We theoretically analyze the form of such CFBGs, and study the characteristics of gratings using piecewise-uniform approach. It is shown that increasing UV-induced index change or the length of the grating or both are the efficient ways to obtain high quality CFBG with high reflectivity and good reflection spectrum. The dispersion of this grating is decided by and varies inversely with the slope of the strain gradient along the length of the grating, not decided by UV-induced index change or by the length of grating. One can control the dispersion and the chirp profile by adjusting the slope of the strain gradient. Based on the theoretical analysis, we have fabricated CFBG whose reflectivity is maintained at 100% in a large range of strain gradients.     

Tunable Bragg gratings for fiber lasers

A tuning method of a fiber Bragg grating by the bending compression-tension is considered. With this method, a relative tuning range of the resonance wavelength of the grating of about 5% has been obtained. The changes in the shape of the spectrum and in the grating reflectivity during the tuning process are studied. The reflectivity of the fiber Bragg grating has been found to considerably increase with increasing degree of compression. It is shown that such an increase is caused by compression-induced changes in the refractive index modulation amplitude in the grating. The fiber Bragg grating developed has been applied for tuning the radiation wavelength of an ytterbium fiber laser. The tuning range of the laser has been found to be 45 nm around the central wavelength 1080 nm.     

Forming of ultrafast light pulses with predetermined temporal shape

The reflectivity function of a grating was modified by diaphragmas near the surface. The temporal shape of an ultrashort laser pulse has been measured after passing the grating spectrograph using a streak camera. This shape exactly mirrors the spatial shape of the reflectivity function of the grating if the laser pulse length is sufficiently small.     

间插取样光纤光栅多通道色散补偿器

对间插取样光纤光栅（ISFBG）进行了理论分析和仿真,给出了ISFBG的折射率表达式,提出了一种在较低的折射率调制深度条件下实现通道间平坦度较好的色散补偿器的制作方法.实验制作了由两个取样光纤光栅间插而成的10通道色散补偿器,其时延抖动大都小于20 ps,通道间平坦度小于1 dB.     

非线性二次曝光法制作三角形光纤Bragg光栅

提出了一种利用非线性二次曝光技术制作三角形光纤Bragg光栅的新方法.该方法只使用普通Bragg位相模板,采用两次曝光技术,通过控制光纤光栅的本地谐振波长和反射率,达到控制光纤光栅谱形的目的.第一次直接对光纤曝光,用来控制光纤光栅谐振波长;第二次通过位相模板曝光,用来控制光纤光栅的反射率.考虑到光敏光纤感光特性曲线的多项e负指数变化规律,按照"分步写入光纤光栅设计软件"进行曝光分布设计,利用"分步曝光光纤光栅写入系统"进行曝光控制,使用信息产业部第46研究所生产的DCS-01型光敏光纤,得到了线性范围1.24 nm、反射率为0～64%的三角形光纤Bragg光栅.三角形光纤Bragg光栅作为光纤光栅传感解调器件,在光纤传感领域具有重要应用价值.