Langmuir-Blodgett assembly of graphite oxide single layers

Single-layer graphite oxide can be viewed as an unconventional type of soft material and has recently been recognized as a promising material for composite and electronics applications. It is of both scientific curiosity and technical importance to know how these atomically thin sheets assemble. There are two fundamental geometries of interacting single layers: edge-to-edge and face-to-face. Such interactions were studied at the air-water interface by Langmuir-Blodgett assembly. Stable monolayers of graphite oxide single layers were obtained without the need for any surfactant or stabilizing agent, due to the strong electrostatic repulsion between the 2D confined layers. Such repulsion also prevented the single layers from overlapping during compression, leading to excellent reversibility of the monolayers. In contrast to molecular and hard colloidal particle monolayers, the single layers tend to fold and wrinkle at edges to resist collapsing into multilayers. The monolayers can be transferred to a substrate, readily creating a large area of flat graphite oxide single layers. The density of such films can be continuously tuned from dilute, close-packed to overpacked monolayers of interlocking single layers. For size-mismatched single layers, face-to-face interaction caused irreversible stacking, leading to double layers. The graphite oxide monolayers can be chemically reduced to graphene for electronic applications such as transparent conducting thin films.     

Stability of emulsions of water in mineral oils containing asphaltenes

Emulsions of water in mineral oils are stable if the oil phase contains asphaltenes which are near the condition of incipient flocculation. This condition is determined by the composition of the oil phase and by the nature of the asphaltenes. High aromaticity of the oil phase and the presence of deflocculants prevent flocculation of asphaltenes; the deflocculants may be interfacially active agents or asphaltene-like compounds with better solubility in the oil phase. Conditions of incipient flocculation of asphaltenes correlate very well with a considerable increase of rheological resistance of the interface between the oil phase and distilled water, determined according to the torsion oscillation method. Stabilization of the water-in-oil emulsions is therefore caused by the build-up of a coherent layer of asphaltenes in the water-oil interface in these cases. Deflocculants of asphaltenes in the oil phase destroy their stabilizing effect; however, the deflocculants themselves may stabilize the water-in-oil emulsions by adsorption on the water-oil interface and then the correlation between the condition of asphaltenes and emulsion stability does not hold, nor is the interfacial viscosity perceptibly increased. Under borderline conditions of emulsion stability a few percent of sodium chloride in the water phase counteracts the build-up of a stabilizing layer of asphaltenes in the water-oil interface and so do higher p_H values of a buffered water phase. At low p_H-values emulsion stability does not correlate with interfacial resistance. It can be concluded that asphaltenes stabilize water-in-oil emulsions if they accumulate on the water-oil interface. This interfacial layer may show a coherence, which is an indication of the presence of asphaltenes rather than a condition for stability of the emulsions.     

Interfacial behaviors of PMMA-PEO block copolymers at the air/water interface

Amphiphilic block copolymers are attracting con-siderable attention because they exhibit unique self- assembly properties in selective organic solvents[1―4]. Semicrystalline poly(ethylene oxide) (PEO), having many interesting physicochemical properties s…     

Probing the Structure and Chemistry of Perylenetetracarboxylic Dianhydride on Graphene Before and After Atomic Layer Deposition of Alumina

The superlative electronic properties of graphene suggest its use as the foundation of next generation integrated circuits. However, this application requires precise control of the interface between graphene and other materials, especially the metal oxides that are commonly used as gate dielectrics. Towards that end, organic seeding layers have been empirically shown to seed ultrathin dielectric growth on graphene via atomic layer deposition (ALD), although the underlying chemical mechanisms and structural details of the molecule/dielectric interface remain unknown. Here, confocal resonance Raman spectroscopy is employed to quantify the structure and chemistry of monolayers of 3,4,9,10-perylenetetracarboxylic dianhydride (PTCDA) on graphene before and after deposition of alumina with the ALD precursors trimethyl aluminum (TMA) and water. Photoluminescence measurements provide further insight into the details of the growth mechanism, including the transition between layer-by-layer growth and island formation. Overall, these results reveal that PTCDA is not consumed during ALD, thereby preserving a well-defined and passivating organic interface between graphene and deposited dielectric thin films.     

Structures and rheological properties of hen egg yolk low density lipoprotein layers spread at the air-water interface at pH 3 and 7

Low density lipoproteins (LDL) from egg yolk have a classical structure of lipoprotein with a core of neutral lipids surrounded by a monolayer of apoproteins and phospholipids. This structure collapses during adsorption and all constituents spread at the interface. To understand better the nature of the interactions between apoproteins and lipids at the interface, we have deposited LDL at an air-water interface and analysed the isotherms during their compression on a Langmuir trough. Then, these LDL films were studied by atomic force microscopy (AFM) imaging. To identify the protein and lipid structures, we imaged films before and after lipid solubilisation by butanol. To study the interactions in the LDL films, we have varied the pH, ionic strength and used simplified model systems. We also studied the correlation between observed structures and interfacial rheology of the film. The isotherms of interfacial LDL films were similar for pH 3 and 7, but their structures observed in AFM were different. At surface pressures below the transition corresponding to the demixion of apoprotein-neutral lipid complexes, the LDL film structure was not governed by electrostatic interactions. However, above this surface pressure transition (45mN/m), there was an effect of charge on this structure. Around the transition zone, the rheological properties of LDL films at pH 3 were different as a function of pH (viscous at pH 3 and visco-elastic at pH 7). So, the rheological properties of LDL films could be linked to the structures formed by apoproteins and observed in AFM.     

Effect of the conditions of transfer on the structure and optical properties of Langmuir graphene oxide films during deposition on a substrate

The effect the solvent and transfer pressure of graphene oxide (SLGO) Langmuir–Blodgett films on the physicochemical properties of monolayers, and on their structural and optical properties, is studied. Examination of the physicochemical properties of SLGO monolayers on subphase surfaces that are formed from SLGO dispersions in different organic solvents reveals that monolayer behavior is virtually independent of the solvent. Electron microscope and optical studies show that the monolayers formed from SLGO dispersions in DMF and acetone have the highest transfer coefficients. It is concluded that the structural heterogeneity of the surfaces of graphene oxide films results from simultaneous effect of electrostatic interactions between graphene oxide particles and Van der Waals interactions with the solvation shell of the particles. Studies focusing on the effect the pressure of transferring a graphene oxide monolayer onto the surface of a solid substrate has on structural features of LB films show that films produced at low surface pressures have more homogeneous structures.     

Surfactant-free water-processable photoconductive all-carbon composite

Heterojunctions between different graphitic nanostructures, including fullerenes, carbon nanotubes and graphene-based sheets, have attracted significant interest for light to electrical energy conversion. Because of their poor solubility, fabrication of such all-carbon nanocomposites typically involves covalently linking the individual constituents or the extensive surface functionalization to improve their solvent processability for mixing. However, such strategies often deteriorate or contaminate the functional carbon surfaces. Here we report that fullerenes, pristine single walled carbon nanotubes, and graphene oxide sheets can be conveniently coassembled in water to yield a stable colloidal dispersion for thin film processing. After thermal reduction of graphene oxide, a solvent-resistant photoconductive hybrid of fullerene-nanotube-graphene was obtained with on-off ratio of nearly 6 orders of magnitude. Photovoltaic devices made with the all-carbon hybrid as the active layer and an additional fullerene block layer showed unprecedented photovoltaic responses among all known all-carbon-based materials with an open circuit voltage of 0.59 V and a power conversion efficiency of 0.21%. The ease of making such surfactant-free, water-processed, carbon thin films could lead to their wide applications in organic optoelectronic devices.     

The Role of Oxidative Debris on Graphene Oxide Films

We study the effect of oxidative impurities on the properties of graphene oxide and on the graphene oxide Langmuir–Blodgett films (LB). The starting material was grupo Antolín nanofibers (GANF) and the oxidation process was a modified Hummers method to obtain highly oxidized graphene oxide. The purification procedure reported in this work eliminated oxidative impurities decreasing the thickness of the nanoplatelets. The purified material thus obtained presents an oxidation degree similar to that achieved by chemical reduction of the graphite oxide. The purified and non‐purified graphene oxides were deposited onto silicon by means of a Langmuir–Blodgett (LB) methodology. The morphology of the LB films was analyzed by field emission scanning microscopy (FE‐SEM) and micro‐Raman spectroscopy. Our results show that the LB films built by transferring Langmuir monolayers at the liquid‐expanded state of the purified material are constituted by close‐packed and non‐overlapped nanoplatelets. The isotherms of the Langmuir monolayer precursor of the LB films were interpreted according to the Volmer’s model.     

Interfacial rheology of stable and weakly aggregated two-dimensional suspensions

The interfacial rheological properties of stable and weakly aggregated two-dimensional suspensions are studied experimentally using a magnetic rod interfacial rheometer. Particle monolayers with well controlled structures were prepared. Charged polystyrene particles create two-dimensional colloidal crystals at the water-decane interface over a wide range of concentrations. Under similar conditions a predominantly liquid structure is obtained at the water-air interface for the same particles. The addition of appropriate combinations of the anionic surfactant sodiumdodecylsulfate (SDS) and sodium chloride (NaCl) to the aqueous subphase leads to a destabilization of these monolayers with the formation of fractal aggregates at low concentrations and a heterogeneous gel forming as the surface coverage is increased. After the structures have been built up a reproducible structure can be obtained, of which the interfacial rheological properties can be investigated using a magnetic rod stress rheometer. In all cases, numerical calculations were used to assess the importance of instrumental artifacts and the effect of the coupling between surface and subphase flows. The rheology of aggregated suspensions was compared to the reference case of a colloidal crystal. The two-dimensional aggregated suspensions display rheological features which are similar to their three-dimensional counterparts. These include an elastic response with small linearity limits, a power law dependence on surface coverage and a dependence on the strength of attraction. The results shed some light on the possible role of interfacial rheology on the stability of particle laden high interface systems. Additionally, the 2D suspensions could present fundamental insights in the rheological properties of dense colloidal suspensions.     

Attenuated total reflection infrared studies of oleate and trioctylphosphine oxide ligand adsorption and exchange reactions on CdS quantum dot films

Ligand exchange reactions at the surface of oleate- and trioctylphosphine oxide (TOPO)-capped CdS quantum dots have been studied with attenuated total reflection infrared (ATR-IR) spectroscopy, using thin films deposited from organic solvent suspensions. The oleate and trioctylphosphine capping ligands were found to form highly ordered and densely packed monolayers on the CdS surface. Adsorbed oleate is coordinated to CdS in a chelating bidentate manner through the carboxylate functional group, while adsorbed trioctylphosphine oxide is coordinated though the P=O functional group and appears to have numerous adsorption environments on the CdS surface. Exposure of such films to aqueous solution was found to cause partial delamination of the films from the ATR prism interface which was reversible upon redrying. Ligand exchange reactions on the oleate- and trioctylphosphine-capped CdS films were studied in situ at room temperature by allowing the films to be exposed to dilute aqueous solutions of thiol-containing ligands. Oleate and trioctylphosphine oxide are both strongly adsorbed to the CdS surface, and ligand exchange with monothiol-containing ligands has been found to be highly dependent upon experimental conditions, in particular pH, where exchange is only observed at solution pH where the exchanging ligand is uncharged. This is attributed to the inability of a charged ligand to penetrate the hydrophobic polymethylene layer on the CdS surface.     

Mechanical properties of hexadecane-water interfaces with adsorbed hydrophobic bacteria

This study focuses on how intact, hydrophobic bacteria in their stationary (i.e., non-dividing) phase could adsorb onto the hexadecane–water interface and alter its mechanical properties. The two strains of bacteria used in forming the interfacial films were Acinetobacter venetianus RAG-1 and Rhodococcus erythropolis 20S-E1-c. Using the dynamic pendant drop technique, the film interfacial tension was monitored as the surface area was made to undergo transient changes. Under static conditions, both types of bacteria had no effect on the interfacial tension. When subjected to transient excitations, however, the two bacterial films exhibited clear and qualitatively similar rheological properties: they responded as two-dimensional Maxwellian materials when the interfacial areas were dilated suddenly, but appeared to be purely elastic upon rapid area compression. Such rheological behaviours are “non-linear” in that the responses of the tension to area dilation and contraction are not mirror images of one another. Despite their qualitative similarities, the two types of film had very distinct film elasticities and relaxation times. The most striking difference between the two bacterial films was revealed under continuous reduction of area, when the A. venetianus RAG-1 system displayed a “paper-like” interface, whereas the interface of the R. erythropolis 20S-E1-c system was “soap film-like”. These macroscopic observations could be explained by the surface ultrastructures of the two cell strains determined using transmission electron microscopy.     

Structure and orientation changes of omega- and gamma-gliadins at the air-water interface: a PM-IRRAS spectroscopy and Brewster angle microscopy study

Microscopic and molecular structures of omega- and gamma-gliadin monolayers at the air-water interface were studied under compression by three complementary techniques: compression isotherms, polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS), and Brewster angle microscopy (BAM). For high molecular areas, gliadin films are homogeneous, and a flat orientation of secondary structures relative to the interface is observed. With increasing compression, the nature and orientation of secondary structures changed to minimize the interfacial area. The gamma-gliadin film is the most stable at the air-water interface; its interfacial volume is constant with increasing compression, contrary to omega-gliadin films whose molecules are forced out of the interface. gamma-Gliadin stability at a high level of compression is interpreted by a stacking model.     

Interfacial rheology of polyelectrolytes and polymer monolayers at the air–water interface

In this review, we describe interfacial rheology studies of polymer monolayers at the air–water interface. Since polyelectrolytes are usually soluble in water, the formation of surface monolayers requires the presence of a surfactant of opposite charge. The first part of the review is dedicated to these mixed monolayers. The second part is related to neutral monolayers that can be either adsorbed or deposited at the interface. Interfacial rheology studies of these systems are still scarce, despite a considerable interest: insoluble polymer monolayers in two dimensions are suitable model systems for the tests of polymer theories in two dimensions, such as and glass transition. The rheology of soluble polymer monolayers has important connections with the dynamic properties of dispersions stabilized with these polymers.     

Surface rheology of PEO-PPO-PEO triblock copolymers at the air-water interface: comparison of spread and adsorbed layers

The dilatational rheological properties of monolayers of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide)-type block copolymers at the air-water interface have been investigated by employing an oscillating ring trough method. The properties of adsorbed monolayers were compared to spread layers over a range of surface concentrations. The studied polymers were PEO26-PPO39-PEO26 (P85), PEO103-PPO40-PEO103 (F88), and PEO99-PPO65-PEO99 (F127). Thus, two of the polymers have similar PPO block size and two of them have similar PEO block size, which allows us to draw conclusions about the relationship between molecular structure and surface dilatational rheology. The dilatational properties of adsorbed monolayers were investigated as a function of time and bulk solution concentration. The time dependence was found to be rather complex, reflecting structural changes in the layer. When the dilatational modulus measured at different concentrations was replotted as a function of surface pressure, one unique master curve was obtained for each polymer. It was found that the dilatational behavior of spread (Langmuir) and adsorbed (Gibbs) monolayers of the same polymer is close to identical up to surface concentrations of approximately 0.7 mg/m2. At higher coverage, the properties are qualitatively alike with respect to dilatational modulus, although some differences are noticeable. Relaxation processes take place mainly within the interfacial layers by a redistribution of polymer segments. Several conformational transitions were shown to occur as the area per molecule decreased. PEO desorbs significantly from the interface at segmental areas below 20 A(2), while at higher surface coverage, we propose that segments of PPO are forced to leave the interface to form a mixed sublayer in the aqueous region.     

Efficient reduction of graphene oxide catalyzed by copper

We report that copper thin films deposited on top of graphene oxide (GO) serve as an effective catalyst to reduce GO sheets in a diluted hydrogen environment at high temperature. The reduced GO (rGO) sheets exhibit higher effective field-effect hole mobility, up to 80 cm(2) V(-1) s(-1), and lower sheet resistance (13 kΩ □(-1)) compared with those reduced by reported methods such as hydrazine and thermal annealing. Raman and XPS characterizations are addressed to study the reduction mechanism on graphene oxide underneath copper thin films. The level of reduction in rGO sheets is examined by Raman spectroscopy and it is well correlated with hole mobility values. The conductivity enhancement is attributed to the growth of the graphitic domain size. This method is not only suitable for reduction of single GO sheets but also applicable to lower the sheet resistance of Langmuir-Blodgett assembled GO films.     

Artemisia herba-alba Asso eco-friendly reduced few-layered graphene oxide nanosheets: structural investigations and physical properties

Nowadays graphene is universally known as a promising material. Hence, the development of eco-friendly synthesis methods for this material is of great importance. This study reports on the bio-synthesis of graphene by a green chemistry process using Artemisia herba-alba Asso (AHAA) natural extract. Moreover, this work reports on the physical properties, including surface/interface and optical and electrical properties of the obtained graphene sheets. UV–VIS, Raman, XPS spectroscopies and TEM microscopy investigations confirmed the reduction, and the conversion of graphene oxide to few-layered reduced graphene oxide as well as the efficiency of this plant extract compared with several natural extracts and chemical agents. Furthermore, it was found that the optical and electrical properties of graphene can be modulated and controlled via this eco-friendly cost-effective process. Hence, AHAA can be an effective chelating agent to produce graphene sheets.     

Photo-Induced Hydrophilicity of TiO<Subscript>2</Subscript> Films Deposited on Stainless Steel via Sol-Gel Technique

The photo-induced hydrophilicity of TiO₂ films deposited on stainless steel substrates and silicon wafers using two different sol-gel routes has been investigated. The results indicate that crystalline titanium oxide films with excellent hydrophilic properties can be obtained on silicon wafer with both routes. XPS and XRD data reveal that films deposited on stainless steel exhibit crystallization features similar to those of films deposited on silicon wafers, and only differ by their oxidation degree owing to a TiO₂ reduction process associated to a diffusion of iron ions during deposition of the acidic sol and/or high temperature post-treatment. Consequently, hydrophilic properties of films deposited on stainless steel are inhibited. The deposition of a SiO_x barrier layer at the film/substrate interface allows preventing such a detrimental substrate influence. A low temperature deposition route of the TiO₂ film associated to the presence of a barrier layer yields best results in preventing iron contamination of the films.     

Mechanical properties of protein adsorption layers at the air/water and oil/water interface: A comparison in light of the thermodynamical stability of proteins

Over the last decades numerous studies on the interfacial rheological response of protein adsorption layers have been published. The comparison of these studies and the retrieval of a common parameter to compare protein interfacial activity are hampered by the fact that different boundary conditions (e.g. physico-chemical, instrumental, interfacial) were used. In the present work we review previous studies and attempt a unifying approach for the comparison between bulk protein properties and their adsorption films. Among many common food grade proteins we chose bovine serum albumin, β-lactoglobulin and lysozyme for their difference in thermodynamic stability and studied their adsorption at the air/water and limonene/water interface. In order to achieve this we have i) systematically analyzed protein adsorption kinetics in terms of surface pressure rise using a drop profile analysis tensiometer and ii) we addressed the interfacial layer properties under shear stress using an interfacial shear rheometer under the same experimental conditions. We could show that thermodynamically less stable proteins adsorb generally faster and yield films with higher shear rheological properties at air/water interface. The same proteins showed an analog behavior when adsorbing at the limonene/water interface but at slower rates.     

Local current mapping and patterning of reduced graphene oxide

Conductive atomic force microscopy (C-AFM) has been used to correlate the detailed structural and electrical characteristics of graphene derived from graphene oxide. Uniform large currents were measured over areas exceeding tens of micrometers in few-layer films, supporting the use of graphene as a transparent electrode material. Moreover, defects such as electrical discontinuities were easily detected. Multilayer films were found to have a higher conductivity per layer than single layers. It is also shown that a local AFM-tip-induced electrochemical reduction process can be used to pattern conductive pathways on otherwise-insulating graphene oxide. Transistors with micrometer-scale tip-reduced graphene channels that featured ambipolar transport and an 8 order of magnitude increase in current density upon reduction were successfully fabricated.     

Understanding Self-assembly,Colloidal Behavior and Rheological Properties of Graphene Derivatives for High-performance Supercapacitor Fabrication

Graphene derivatives, such as graphene oxide(GO) and reduced graphene oxide(RGO), have been widely used as promising twodimensional nanoscale building blocks due to their fascinating properties, cost-effective production, and good processability. Understanding the intrinsic self-assembling, colloidal, and rheological features of graphene derivatives is of critical importance to establish the formation-structureproperty relationship of graphene-based materials. This article reviews recent progresses in our studies of these interesting properties of graphene derivatives for developing high performance supercapacitors. The content is organized to include characteristics of the dispersions of graphene derivatives, self-assembly of nanosheets from liquid medium, colloidal behavior, rheological properties of the dispersions, processing methods based on the properties, and performance of the fabricated supercapacitors. GO and RGO nanosheets are proved to form different types of assembled structures with unique morphologies, such as ultrathin layer-by-layer films, porous aggregates, and nanoscrolls. The unique rheological properties of GO dispersions and hydrogels, feasible for both the traditional wet-processing and newly-developed technology like three-dimensional printing, are highlighted for their potential in structural manipulation and scalable fabrication of graphene-based devices. The research devoted to up-grading the performance of supercapacitors is presented in some details, which could be applicable for fabricating other graphene-based energy storage devices. Some challenges and perspectives in our point of view are given in the last part of this feature article.