ZnO/MgO nanocomposites generated from alcoholic solutions

A process was proposed for the synthesis of ZnO/MgO nanocomposites from alcoholic solutions by means or the consecutive precipitation of coprecipitation of alcoholic solutions of zinc acetate and magnesium with an alkali solution followed by annealing in the range 400–500°C. X-ray powder diffraction showed crystalline ZnO and MgO phases in the resulting composite. Zinc oxide particle sizes in the composite with magnesium oxide were determined by transmission electron microscopy and from X-ray diffraction peak broadening. The zinc oxide nanoparticle size was weakly affected by the molar ratio of zinc to magnesium and the concentration of the precipitated component. The ZnO exciton peak in cathodoluminescence spectra for nanocomposites synthesized at low temperatures (400 and 500°C) shifted toward the UV. At ≥600°C or higher, Mg_{1 ? x} Zn _x O solid solution was generated, as evidenced by X-ray diffraction and cathodoluminescence data.     

Facile synthesis of spray pyrolyzed ZnO/NiO nanocomposites thin films

Abstract

This study reviews ZnO, NiO, and ZnO/NiO nanocomposites thin films deposition using the Spray Pyrolysis Technique (S.P.T). The thin films were deposited onto ordinary glass substrates heated at 500?°C from aqueous solutions of zinc chloride and nickel chloride precursors dissolved in distilled water. The structural, morphological, and optical properties of the ZnO, NiO, and ZnO/NiO thin films have been studied by X-ray diffraction, scanning electron microscopy, Raman spectroscopies, and so on. The optical band gaps are 3.3 and 3.5?eV for ZnO and NiO thin films, respectively obtained by UV–Vis spectroscopy. However, the optical band gaps of ZnO/NiO nanocomposites thin films, are noticeable out of the range (3.4–3.64?eV).     

Evolution of surface topography and optical band gap of ZnO film deposited on NiO/Si(100)

Evolution of surface features and optical band gap of ZnO thin films deposited on different NiO/Si(100) are reported. In order to create different initial microstructure, we first deposited NiO film on Si(100) at 3 different temperatures (400°C, 650°C, and 700°C) by pulsed laser deposition. These NiO/Si(100) films are used as substrate for the deposition of ZnO films. Combining the results obtained from grazing incidence X‐ray diffraction, atomic force microscope, and UV‐Visible characterization, our study indicated that the microstructure of the substrate takes the important role in dictating properties of the film. Our study also indicated that one needs to choose appropriate synthesis condition to achieve good quality ZnO films.     

New Synthesis and Magnetic Properties of NiFe2O4/SiO2 and Co0.5Zn0.5Fe2O4/SiO2 Nanocomposites Using Tetraglycolatosilane as Precursor

In this work the new synthesis and magnetic properties of NiFe₂O₄/SiO₂ and Co_0.5Zn_0.5Fe₂O₄/SiO₂ nanocomposites using a water‐soluble silica precursor, tetraglycolatosilane (THEOS), by the sol‐gel method were reported. Nanocomposite were obtained by the thermal decomposition of the organic part at different annealing temperatures varying from 400 to 900 °C. Studies carried out using XRD, FT‐IR, TEM, STA (TG‐DTG‐DTA) and VSM techniques. XRD patterns show that NiFe₂O₄ and Co_0.5Zn_0.5Fe₂O₄ have been formed in an amorphous silica matrix at annealing temperatures above 600 and 400 °C, respectively. It is found that when the annealing temperature is up to 900 °C NiFe₂O₄/SiO₂ and Co_0.5Zn_0.5Fe₂O₄/SiO₂ samples show almost superparamagnetic behavior with a magnetization 4.66 emu/g and ferromagnetic behavior with a magnetization 10.11 emu/g, respectively. The magnetization and coercivity values of nanocomposites using THEOS were considerably less than previous reports using TEOS. THEOS as a silica matrix network provides an ideal nucleation environment to disperse ferrite nanoparticles and thus to confine them to aggregate and coarsen. By using THEOS over the currently used TEOS and TMOS, organic solvents are not needed due to the entire solubility of THEOS in water. Synthesized nanocomposites with adjustable particle sizes and controllable magnetic properties make the applicability of ferrites even more versatile.     

Effects of doping with CeO2 and calcination temperature on physicochemical properties of the NiO/Al2O3 system

The effects of doping with CeO₂ and calcination temperature on the physicochemical properties of the NiO/Al₂O₃ system have been investigated using DTA, XRD, nitrogen adsorption measurements at −196°C and decomposition of H₂O₂ at 30–50°C. The pure and variously doped solids were subjected to heat treatment at 300, 400, 700, 900 and 1000°C. The results revealed that the specific surface areas increased with increasing calcination temperature from 300 to 400°C and with doping of the system with CeO₂. The pure and variously doped solids calcined at 300 and 400°C consisted of poorly crystalline NiO dispersed on γ-Al₂O₃. Heating at 700°C resulted in formation of well crystalline NiO and γ-Al₂O₃ phases beside CeO₂ for the doped solids. Crystalline NiAl₂O₄ phase was formed starting from 900°C. The degree of crystallinity of NiAl₂O₄ increased with increasing the calcination temperature from 900 to 1000°C. An opposite effect was observed upon doping with CeO₂. The NiO/Al₂O₃ system calcined at 300 and 400°C has catalytic activity higher than individual NiO obtained at the same calcination temperatures. The catalytic activity of NiO/Al₂O₃ system increased, progressively, with increasing the amount of CeO₂ dopant and decreased with increasing the calcination temperature.     

SiO2/ZnO复合纳米粒子的制备及表征

采用双注控制沉积法(Controlled Double-Jet Precipitation,CDJP)将反应物添加到含有SiO₂的溶液中,通过直接的表面反应来制备单分散的SiO₂/ZnO复合纳米粒子,并对其进行了表征。透射电镜(TEM)观察表明,SiO₂表面有一层ZnO纳米颗粒或薄层。对复合纳米粒子SiO₂/ZnO进行X射线衍射(XRD)分析,复合颗粒的衍射峰与单独的氧化锌的衍射峰完全一致。能量弥散X射线法(EDX)分析表明,复合颗粒中含有Zn、Si、O元素。荧光光谱表明有ZnO的吸收峰。     

Enhancing the Photo and Biomedical Activity of ZnO by Incorporation with Zinc Silicate Nanocomposites

Highly active and non-toxic ZnO incorporated with zinc silicate (zinc silicate/ZnO) nanocomposites are synthesized via a simple and low-cost hydrothermal method followed by heat treatment. Different molar ratios from Si to Zn [1:20], [1:10], [1:8] and [1:6] are used to prepare different zinc silicate/ZnO nano composite materials which are assigned to ZS1, ZS2, ZS3 and ZS4 samples, respectively. The effect of calcination times and temperatures have been investigated on the crystallographic and morphological properties of the synthesized nano composite materials. The XRD analysis show that at very low molar ratios, zincite (ZnO) is the most predominant phase. However, at higher molar ratios, there are two phases coexist; hemimorphite (Zn₄Si₄O₇) and zincite. The TEM images show a uniform nanoplate-like shaped morphology from ZnO with well dispersed Zn₂SiO₄ nanoparticles. The S_BET is remarkably increased from 18.14 to 176.5 m².g⁻¹ by calcination up to 400 °C and then decreased to 72.2 m². g⁻¹ by further increasing in the calcinations temp up to 1,000 °C. The bio and photocatalytic activities of the composite nanomaterials have been investigated. Compared with the pure ZnO, the nano composites have been demonstrated as better photocatalysts for the degradation of Levafex golden yellow (LGY) dye as a model of organic dye pollutant under simulated sunlight irradiation. Moreover, the nano composites were evidenced to possess better and non-toxic antitumor activity towards hepatocellular carcinoma cell lines with (IC₅₀ = 11.2 μg.ml⁻¹ and LD₅₀ ˃ 50 mg. Kg⁻¹).     

Synthesis,magnetic properties and X-ray analysis of Zn0.97X0.03O nanoparticles (X = Mn,Ni, and Co) using Scherrer and size–strain plot methods

Un-doped and doped ZnO nanoparticles (Zn_0.97X_0.03O-NPs, X = Mn, Co, and Ni) were synthesized from a metal acetate precursor and acetic acid by a modified sol–gel combustion method. The compounds were synthesized at calcination temperatures of 650 °C for 1 h. The synthesized un-doped/doped ZnO-NPs were characterized by X-ray diffraction analysis (XRD) and high-magnification transmission electron microscopy (TEM). The XRD results revealed that the sample product was crystalline with a hexagonal wurtzite phase. The TEM showed ZnO-NPs nearly spherical shapes and a non-uniform shape for doped ZnO-NPs. The crystalline development in the ZnO-NPs was investigated by X-ray peak broadening. The size–strain plot (SSP) method was used to study the individual contributions of crystallite sizes and lattice strain on the peak broadening of the un-doped and doped ZnO-NPs. Physical parameters such as strain, stress and energy density values were calculated more precisely for all reflection peaks of XRD corresponding to the wurtzite hexagonal phase of ZnO lying in the range of 20–80° from the SSP results. The vibrating sample magnetometer (VSM) was also used to study the magnetic behavior of the samples in the ceramic form. The obtained results showed that strain play an important role in peak broadening; moreover, the mean crystalline size of the un-doped and doped ZnO-NPs estimated from the TEM and the SSP method were highly inter-correlated.     

A highly sensitive nonenzymatic glucose sensor based on nickel oxide–carbon nanotube hybrid nanobelts

In this study, we demonstrated a highly sensitive electrochemical sensor for the determination of glucose in alkaline aqueous solution by using nickel oxide single-walled carbon nanotube hybrid nanobelts (NiO–SWCNTs) modified glassy carbon electrode (GCE). The hybrid nanobelts were prepared by the deposition of SWCNTs onto the Ni(SO₄)_0.3(OH)_1.4 nanobelt surface, followed by heat treatment at different temperatures ranging from 400 °C to 600 °C. The NiO–SWCNTs hybrid nanobelts modified electrode prepared at 500 °C displays enhanced electrocatalytic activity towards glucose oxidation, revealing a synergistic effect between the NiO and the deposited SWCNTs. The as-fabricated nonenzymatic glucose sensor exhibits excellent glucose sensitivity (2,980 μA cm^?2 mM^?1), lower detection limit (0.056 μM, signal/noise [S/N] ratio?=?3), and wider linear range (0.5–1,300 μM). Moreover, the sensor has been successfully used for the assay of glucose in serum samples with good recovery, ranging from 96.4 % to 102.4 %.     

Carbonization and graphitization of pitch applied for anode materials of high power lithium ion batteries

The artificial graphite materials were prepared by carbonizing coal tar pitch using two methods, namely, one- and two-step processes, and all sintered samples were graphitized at 2800 °C. Effects of different heat treatments on the performance of the samples were characterized by scanning electron microscopy, transmission electron microscopy (TEM), X-ray diffraction, Brunauer–Emmett–Teller, electrochemical impedance spectroscopy (EIS), particle size analysis, polarized light microscopy, and charge–discharge measurements. All samples show a typical graphite crystalline structure; moreover, the degree of graphitization (g factor) and crystallite size along the c-axis (L _c ) were calculated from (002) peak. The polarized light microscopy indicates that the coke with carbonization at 700 °C has an obvious wide domain (D) optical structure, while that with two-step sintering at 400 and 700 °C has a mixed optical structures of wide D, flow domains, and mosaics. TEM analysis revealed a number of irregular graphene layer images which are caused by the defects of graphite. EIS shows that the sample carbonized by two-step has a larger diffusion coefficient than the sample carbonized at 700 °C by one step. Higher carbonization temperature leads to better cycle performance as the temperature increasing from 500 to 700 °C in the one-step route. Specifically, the charge (Li⁺ extraction) capacity at the 50th cycle increases from 318 mA?h?g^?1 to 357 mA?h?g^?1. The results show that the rate performance of the artificial graphite is improved with the addition of the presintering at 400 °C.     

Net-structured NiO–C nanocomposite as Li-intercalation electrode material

Net-structured NiO was prepared by urea-mediated homogeneous hydrolysis of Ni(CH₃COO)₂ under microwave radiation followed by a calcination at 500 °C. NiO–C nanocomposite was prepared by dispersing the as-prepared net-structured NiO in glucose solution and subsequent carbonization under hydrothermal conditions at 180 °C. The carbon in the composite was amorphous by the X-ray diffraction (XRD) analysis, and its content was 15.05 wt% calculated according to the energy dispersive X-ray spectroscopy (EDX) result. Transmission electron microscopy (TEM) image of the NiO–C nanocomposite showed that the NiO network was homogeneously filled by amorphous carbon. The reversible capacity of NiO–C nanocomposite after 40 cycles is 429 mAh g⁻¹, much higher than that of NiO (178 mAh g⁻¹). These improvements are attributed to the carbon, which can enhance the conductivity of NiO, suppress the aggregation of active particles, and increase their structure stability during cycling.     

Preparation and characterization of novel polyimide/functionalized ZnO bionanocomposite for gas separation and study of their antibacterial activity

In the present investigation novel Polyimide/functionalized ZnO (PI/ZnO) bionanocomposites containing amino acid (Methionine) and benzimidazole pendent groups with different amounts of modified ZnO nanoparticles (ZnO NPs) were successfully prepared through ultrasonic irradiation technique. Due to the high surface energy and tendency for agglomeration, the surface ZnO NPs was modified by a coupling agent as 3- methacryloxypropyl-trimethoxysilane (MPS) to form MPS-ZnO nanoparticles. The ultrasonic irradiation effectively changes the rheology and the glass transition temperature and the crystallinity of the composite polymer. PI/ZnO nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscope (TEM). TEM analysis showed that the modified ZnO nanoparticles were homogeneously dispersed in polymer matrix. The TGA results of PI/ZnO nanocomposites showed that the thermal stability is obviously improved the presence of MPS-ZnO NPs in comparison with the pure PI and that this increase is higher when the NP content increases. The permeabilities of pure H₂, CH₄, O₂, and N₂ gases through prepared membranes were determined at room temperature (25 °C) and 20 bar feed pressure. The membranes having 20% ZnO showed higher values of H₂ permeability, and H₂/CH₄ and H₂/N₂ ideal selectivities (the ratio of pair gas permeabilities) compared with other membranes. The antibacterial activity of bionanocomposite films was tested against gram-positive bacteria (Staphylococcus aureus and Bacillus subtilis) and gram-negative bacteria (Escherichia coli and Pseudomonas aeruginosa). Further, it was observed that antibacterial activity of the resulting hybrid biofilms showed somewhat higher for gram-positive bacteria compared to gram-negative bacteria.     

Fabrication of Porous Metal Oxide Semiconductor Films by a Self-Template Method Using Layered Hydroxide Metal Acetates

Porous metal oxide (Co₃O₄, NiO, or ZnO) films were fabricated by a self-template method using layered hydroxide metal acetates (LHMA; metal = Co, Ni, or Zn) as templates. LHMAs were initially grown on glass substrates through a chemical bath deposition in methanolic-aqueous solutions of metal acetates at 60°C. The template films had a unique, nest-like morphology consisting of interlaced flake-like particles as a result of two-dimensional crystal growth of LHMAs in supersaturated solutions. The templates were successfully converted into porous Co₃O₄, NiO, or ZnO films by heating at 500°C for 10 min in air without microstructural deformation.     

Preparation,characterization and activity evaluation of p–n junction photocatalyst p-NiO/n-ZnO

In this paper, p–n junction photocatalyst NiO/ZnO was prepared by the sol–gel method using Ni (NO₃)₂ and zinc acetate as the raw materials. The structural and optical properties of the p–n junction photocatalyst NiO/ZnO were characterized by X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET) analysis, UV–Vis diffuse reflection spectrum (DRS) and the fluorescence emission spectra. The photocatalytic activity of the photocatalyst was evaluated by photocatalytic reduction of Cr₂O₇ ²⁻ and photocatalytic oxidation of methyl orange (MO). The results showed that the photocatalytic activity of the p–n junction photocatalyst NiO/ZnO is much higher than that of ZnO on the photocatalytic reduction of Cr₂O₇ ²⁻. However, the photocatalytic activity of the photocatalyst is much lower than that of ZnO on the photocatalytic oxidation of methyl orange. Namely, the p–n junction photocatalyst NiO/ZnO has higher photocatalytic reduction activity, but lower photocatalytic oxidation activity. The heat treatment condition also influences the photocatalytic activity strongly, and the best preparation condition is about 400 °C for 2 h. Effect of the heat treatment condition on the photocatalytic activity of the photocatalyst was also investigated. The mechanisms of influence on the photocatalytic activity were discussed by the p–n junction principle.     

ZnO/Co3O4 Porous Nanocomposites Derived from MOFs: Room‐Temperature Ferromagnetism and High Catalytic Oxidation of CO

ZnO/Co₃O₄ porous nanocomposites were successfully fabricated by the thermal decomposition of Prussian Blue analogue (PBA) Zn₃[Co(CN)₆]₂ nanospheres obtained at room temperature. Interestingly, ZnO/Co₃O₄ porous nanocomposites exhibit room‐temperature ferromagnetism. Moreover, the ZnO/Co₃O₄ porous nanocomposites show good catalytic activity for CO oxidation, and the CO conversion rate reaches 100 % at 250 °C. It is suggested that the synergistic effect of each component, relative high surface area (32 m² g^?1) and porous structure lead to the promising catalytic properties.     

Glass formation and confined melting in sol–gel derived nano-ZnO aggregates

Sol–gel processing of ZnO nanocolloids has been revisited to prepare various alkaline metal acetate (MAc: K, Na, Li-acetates) containing ZnO nanopowders. Using differential scanning calorimetry and X-ray diffraction investigations, several new relationships between the morphology and the thermodynamic behavior in the aforementioned particulate ZnO/MAc nanocomposites were noticed: (1) large MAc melting depression shifts ?ΔT_m ~ 80 °C due to salt confinement within porous ZnO aggregates, (2) corresponding MAc crystallization and re-crystallization temperature depression shifts, (3) presence of multimodal pore size distributions within nanoaggregates and (4) glass formation at temperatures T_g between ?40 and 130 °C. We also note that the T_g value drops with rising alkaline metal size, increasing water content and decreasing ZnO particle size. In contrast, T_g rises in the case of co-doped Fe–LiAc/ZnO compositions.     

Calcination temperature-dependent morphology of photocatalytic ZnO nanoparticles prepared by an electrochemical–thermal method

ZnO nanoparticles (NPs) with tunable morphologies were synthesized by a hybrid electrochemical–thermal method at different calcination temperatures without the use of any surfactant or template. The NPs were characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction, dynamic light scattering, thermogravimetry–differential thermal analysis, scanning electron microscope and N₂ gas adsorption–desorption studies. The FT-IR spectra of ZnO NPs showed a band at 450 cm^?1, a characteristic of ZnO, which remained fairly unchanged at calcination temperatures even above 300 °C, indicating complete conversion of the precursor to ZnO. The products were thermally stable above 300 °C. The ZnO NPs were present in a hexagonal wurtzite phase and the crystallinity of ZnO increased with an increasing calcination temperature. The ZnO NPs calcined at lower temperature were mesoporous in nature. The surface areas of ZnO NPs calcined at 300 and 400 °C were 51.10 and 40.60 m² g^?1, respectively, which are significantly larger than commercial ZnO nanopowder. Surface diffusion has been found to be the key mechanism of sintering during heating from 300 to 700 °C with the activation energy of sintering as 8.33 kJ mol^?1. The photocatalytic activity of ZnO NPs calcined at different temperatures evaluated by photocatalytic degradation of methylene blue under sunlight showed strong dependence on the surface area of ZnO NPs. The ZnO NPs with high surface area showed enhanced photocatalytic activity.     

Synthesis,characterization, and thermal stability of poly (lactic acid)/zinc oxide pillared organic saponite nanocomposites via ring‐opening polymerization of d,l‐lactide

Poly (lactic acid) (PLA) was synthesized using d , l ‐lactide monomer and zinc oxide (ZnO) pillared organic saponite as the green catalyst, through ring‐opening polymerization. The effects of stoichiometry of catalyst and polymerization conditions on molecular weight of PLA were evaluated by orthogonal experiment. The optimum polymerization parameters were: 0.5 wt% ZnO pillared organic saponite and reaction conditions of 170°C for 20 hr. Fourier transform infrared spectroscopy and ¹H nuclear magnetic resonance spectroscopy confirmed the PLA structure. Gel permeation chromatography showed that the average molecular weight of PLA was 48,442 g/mol, and its polydispersity index was 1.875. Differential scanning calorimetry, X‐ray diffraction, and polarized optical microscopy showed that ZnO pillared organic saponite improved the crystallinity of PLA. Thermal gravimetric analysis showed improved thermal stability of PLA because of ZnO pillared organic saponite. Thermal decomposition kinetics of PLA/ZnO pillared organic saponite nanocomposites was also studied. The activation energies (E_a) for thermal degradation of PLA and PLA/ZnO pillared organic saponite nanocomposites were evaluated by the Kissinger and Ozawa methods, which demonstrated that ZnO pillared organic saponite enhanced E_a of thermal degradation of PLA and significantly improved its thermal stability. Copyright © 2015 John Wiley & Sons, Ltd.     

Effect of gamma-irradiation on some structural characteristics of NiO

Pure NiO specimens were prepared by the thermal decomposition of pure basic nickel carbonate in air at 400 and 600°C. The obtained solids were exposed to different doses of γ-irradiation ranging between 10–80 Mrad. The change in residual microstrain, lattice parameter and crystallite size due to the irradiation process were investigated by X-ray diffraction analyses.The results revealed that γ-irradiation effected important changes in the structural characteristics of NiO lattice. No detectable change was observed for the crystalline size of NiO-400°C; however, the crystallite size of NiO-600°C decreased by increasing the dose up to 20 Mrad and increased at higher doses but still remaining smaller than that measured for the unirradiated specimen.The lattice parameters of NiO preheated at 400 or 600°C were found to increase as a function of the dose. These results were attributed to progressive removal of Ni³⁺ ions acting as lattice defects in NiO solid.The microstrains in NiO specimens precalcined either at 400 or 600°C were found to decrease progressively by increasing the dose falling to minimum values at doses of 40 and 80 Mrad for the solids preheated at 600 and 400°C, respectively. The augmentation of the exposure dose above 40 Mrad for NiO-600°C resulted in an increase in microstrain which, however, remained always smaller than those found for the unirradiated solid. The strain-relief in NiO-600°C due to γ-irradiation took place, mainly, via splitting of its crystallites. On the other hand, the progressive removal of lattice defects (Ni³⁺ ions) due to the irradiation process might account for the observed strain-relief in NiO-400°C.     

Structural,optical and magnetic characterization of ZnO nanorods synthesized using hydrothermal technique at low temperature

Pure ZnO nanorods were grown from aqueous solutions at low temperature (90 °C) by hydrothermal growth technique on sapphire (0001) substrate coated with ZnO thin film. X-ray diffraction results show that these nanorods crystallize in the wurtzite structure having space group P6₃mc and that they are oriented along the c-axis. Raman and photo-luminescence studies show the presence of oxygen vacancies in the ZnO nanorods. The ZnO nanorods show room temperature ferromagnetism.