Calcined Mg-Al Layered Double Hydroxide as a Heterogeneous Catalyst for the Synthesis of Urea Derivatives from Amines and CO2

The calcined Mg‐Al layered double hydroxides (LDHs) with a Mg/Al molar ratio of 3:1 were synthesized and characterized thoroughly by X‐ray diffraction (XRD), temperature‐programmed desorption (TPD) of CO₂, and thermogravimetric analysis (TGA). Thus the calcined Mg‐Al LDHs were used as catalyst for the catalytic synthesis of disubstituted ureas from amines and CO₂. The effects of reaction time, reaction temperature, pressure, solvent and calcined temperature on activity have been investigated. The results indicated that aliphatic amines, cyclohexylamine and benzylamine can be converted to the corresponding ureas selectively over the calcined Mg‐Al LDHs catalysts with N‐methyl‐2‐pyrrolidone (NMP) as solvent without using any dehydrating regent. The catalyst can be recycled several times with only slight loss of activity.     

Cu functionalized nano crystalline ZSM-5 as efficient catalyst for selective oxidation of toluene

Nano crystalline ZSM-5 (NZ) functionalized with Cu has been explored for the selective oxidation of toluene to benzoic acid for the first time, where a comparison is made with the traditional microcrystalline ZSM-5 (MZ) based catalyst having similar framework Si/Al ratios at organic solvent-less reaction conditions in presence of H₂O₂ as a green oxidant. The ZSM-5 catalysts exhibited oxidation property even in the absence of any Cu species, but with low toluene conversions and benzoic acid yields. Functionalization with Cu greatly enhanced the benzoic acid formation, especially on NZ loaded with 0.4 wt% of Cu (Cu-NZ) to produce 92 wt% of benzoic acid, by virtue of the presence of highly dispersed nano particles of CuO along with Cu⁺² ions on the high surface area, mesopore possessing NZ support, revealed from XRD, N₂ adsorption-desorption, XPS, SEM, TEM, FITR, TPR and TPD analysis.     

5-磺基水杨酸辅助水热法制备Co-Ni层状双氢氧化物及其超电容性能

采用5-磺基水杨酸(SSA)辅助水热法制备了Co-Ni层状双氢氧化物(CoxNi1-xLDHs),通过X射线衍射(XRD)、傅里叶变换红外(FT-IR)光谱、场发射扫描电镜(FE-SEM)和透射电镜(TEM)研究其结构与形貌.结果表明,通过调控反应体系中Co、Ni的配比,可以得到不同形貌的CoxNi1-xLDHs.在Co的摩尔分数为0.24时,形成了由纳米片组装的花瓣状纳米球.循环伏安和恒流充放电测试表明,这种花瓣状结构的双氢氧化物在1A·g-1电流密度下,比电容值达到1735F·g-1.     

Hydrogen production by methanol steam reforming on a cordierite monolith reactor coated with Cu–Ni/LaZnAlO<Subscript>4</Subscript> and Cu–Ni/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

The performance of Cu–Ni/LaZnAlO₄ and Cu–Ni/γ-Al₂O₃ catalysts in the methanol reforming process in a monolith reactor in the temperature range of 200–350 °C, feed flow rate of WHSV = 20.8 h^?1 and atmospheric pressure has been investigated. In order to perform a more thorough investigation, surface area, morphology and crystalline structure of the synthetic catalysts have been studied using BET, FE-SEM, TPR, FT-IR, TEM, TGA and XRD analyses. The results have shown that Cu–Ni/LaZnAlO₄ catalyst synthesized by combustion reaction method under ultrasound irradiation has a very high efficiency and catalytic activity, low reduction temperature, high mechanical resistance and large pore sizes. The latter causes a higher percentage of active metal impregnation and better distribution on the support, greater resistance against sintering and maintenance of catalyst inertness at temperatures over 1000 °C, in comparison with conventional catalysts such as Cu–Ni/γ-Al₂O₃. This make its substitution for currently used catalysts affordable.     

Production of hydrogen by oxidative steam reforming of methanol over Cu/SiO2 catalysts

Selective production of hydrogen by oxidative steam reforming of methanol (OSRM) was studied over Cu/SiO₂ catalyst using fixed bed flow reactor. Textural and structural properties of the catalyst were analyzed by various instrumental methods. TPR analysis illustrates that the reduction temperature peak was observed between 510?K and 532?K at various copper loadings and calcination temperatures and the peaks shifted to higher temperature with increasing copper loading and calcination temperature. The XRD and XPS analysis demonstrates that the copper existed in different oxidation states at different conditions: Cu₂O, Cu⁰, CuO and Cu(OH)₂ in uncalcined sample; CuO in calcined sample: Cu₂O and metallic Cu after reduction at 600?K and Cu⁰ and CuO after catalytic test. TEM analysis reveals that at various copper loadings, the copper particle size is in the range between 3.0?nm and 3.8?nm. The Cu particle size after catalytic test increased from 3.6 to 4.8?nm, which is due to the formation of oxides of copper as evidenced from XRD and XPS analysis. The catalytic performance at various Cu loadings shows that with increasing Cu loading from 4.7 to 17.3?wt%, the activity increases and thereafter it decreases. Effect of calcination shows that the sample calcined at 673?K exhibited high activity. The O₂/CH₃OH and H₂O/CH₃OH molar ratios play important role in reaction rate and product distribution. The optimum molar ratios of O₂/CH₃OH and H₂O/CH₃OH are 0.25 and 0.1, respectively. When the reaction temperature varied from 473 to 548?K, the methanol conversion and H₂ production rate are in the range of 21.9–97.5% and 1.2–300.9?mmol?kg^?1?s^?1, respectively. The CO selectivity is negligible at these temperatures. Under the optimum conditions (17.3?wt%, Cu/SiO₂; calcination temperature 673?K; 0.25 O₂/CH₃OH molar ratio, 0.5 H₂O/CH₃OH molar ratio and reaction temperature 548?K), the maximum hydrogen yield obtained was 2.45?mol of hydrogen per mole of methanol. The time on stream stability test showed that the Cu/SiO₂ catalyst is quite stable for 48?h.     

Selective oxidation of alcohols with hydrogen peroxide catalyzed by tungstate ions (WO4) supported on periodic mesoporous organosilica with imidazolium frameworks (PMO-IL)

Tungstate ions supported on the periodic mesoporous organosilica with ionic liquid frameworks (WO₄⁼@PMO-IL) were found to be a recoverable catalyst system for the highly selective oxidation of various primary or secondary alcohols to the corresponding aldehydes or ketones by 30% H₂O₂ as green oxidant under neutral aqueous reaction conditions. The catalyst can be also recovered and efficiently reused in seven subsequent reaction cycles without any remarkable decreasing in the catalyst activity and selectivity. Moreover, N₂ sorption analysis, transmission electron microscopy (TEM) images, and thermal gravimetric analysis (TGA) showed that the structure regularity and functional groups loaded of the catalyst were not affected during the reaction process.     

Hydrodechlorination of 4-Chlorophenol on Pd-Fe Catalysts on Mesoporous ZrO2SiO2 Support

A mesoporous support based on silica and zirconia (ZS) was used to prepare monometallic 1 wt% Pd/ZS, 10 wt% Fe/ZS, and bimetallic FePd/ZS catalysts. The catalysts were characterized by TPR-H₂, XRD, SEM-EDS, TEM, AAS, and DRIFT spectroscopy of adsorbed CO after H₂ reduction in situ and tested in hydrodechlorination of environmental pollutant 4-chlorophelol in aqueous solution at 30 °C. The bimetallic catalyst demonstrated an excellent activity, selectivity to phenol and stability in 10 consecutive runs. FePd/ZS has exceptional reducibility due to the high dispersion of palladium and strong interaction between FeOx and palladium, confirmed by TPR-H₂, DRIFT spectroscopy, XRD, and TEM. Its reduction occurs during short-time treatment with hydrogen in an aqueous solution at RT. The Pd/ZS was more resistant to reduction but can be activated by aqueous phenol solution and H₂. The study by DRIFT spectroscopy of CO adsorbed on Pd/ZS reduced in harsh (H₂, 330 °C), medium (H₂, 200 °C) and mild conditions (H₂ + aqueous solution of phenol) helped to identify the reasons of the reducing action of phenol solution. It was found that phenol provided fast transformation of Pd⁺ to Pd⁰. Pd/ZS also can serve as an active and stable catalyst for 4-PhCl transformation to phenol after proper reduction.     

Cu(II) immobilized on mesoporous organosilica as an efficient and reusable nanocatalyst for one‐pot Biginelli reaction under solvent‐free conditions

Cu(II) immobilized on mesoporous organosilica nanoparticles (Cu²⁺@MSNs‐(CO₂^?)₂) has been synthesized, as a inorganic–organic nanohybrid catalyst, through a post‐grafting approach. Its characterization is carried out by Fourier transform infrared spectroscopy (FT‐IR), X‐ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Energy dispersive X‐ray (EDX), Thermogravimetric/differential thermal analyses (TGA‐DTA), and Nitrogen adsorption–desorption analysis. Cu²⁺@MSNs‐(CO₂^?)₂ exhibits high catalytic activity in the Biginelli reaction for the synthesis of a diverse range of 3, 4‐dihydropyrimidin‐2(1H)‐ones, under mild conditions. The anchored Cu(II) could not leach out from the surface of the mesoporous catalyst during the reaction and it has been reused several times without appreciable loss in its catalytic activity.     

Pure CuCr2O4 nanoparticles: Synthesis,characterization and their morphological and size effects on the catalytic thermal decomposition of ammonium perchlorate

In the present paper a pure phase of the copper chromite spinel nanoparticles (CuCr₂O₄ SNPs) were synthesized via the sol–gel route using citric acid as a complexing agent. Then, the CuCr₂O₄ SNPs has been characterized by field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). In the next step, with the addition of Cu–Cr–O nanoparticles (NPs), the effects of different parameters such as Cu–Cr–O particle size and the Cu/Cr molar ratios on the thermal behavior of Cu–Cr–O NPs + AP (ammonium perchlorate) mixtures were investigated. As such, the catalytic effect of the Cu–Cr–O NPs for thermal decomposition of AP was evaluated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA/DSC results showed that the samples with different morphologies exhibited different catalytic activity in different stages of thermal decomposition of AP. Also, in the presence of Cu–Cr–O nanocatalysts, all of the exothermic peaks of AP shifted to a lower temperature, indicating the thermal decomposition of AP was enhanced. Moreover, the heat released (ΔH) in the presence of Cu–Cr–O nanocatalysts was increased to 1490 J g⁻¹.     

Synthesis of Mono-Dispersed Mg(OH)2 Nanoflakelets

Mono-dispersed Mg(OH)₂ nanoflakelets have been prepared with the assistant of 4-(p-nitrophenylazo)resorcinol. The samples were characterized using XRD, TEM, and ED. Electron diffraction analysis showed that single crystalline nanoflakelets were obtained in hydrothermal process, and porous Mg(OH)₂ nanosheets were prepared at lower temperature. Nitrogen adsorption isotherms show that the surface area of Mg(OH)₂ nanosheets is 129 m²/g. Possible growth mechanism of the nanoflakelets is discussed.     

Removal of sulfate from wastewater via synthetic Mg–Al layered double hydroxide: An adsorption,kinetics, and thermodynamic study

Sulfate-contaminated water is a major environmental problem that alters the taste of water, disturbs the digestive systems of animals and humans, and erodes both soil and metals. In this study, the layered double hydroxide LDH 4Mg2Al·NO₃ and LDH 8Mg2Al·NO₃ were prepared using a co-precipitation technique, and applied in the adsorption of SO₄^2- from an aqueous solution. The reaction is well described by the Langmuir adsorption model. LDH 4Mg2Al·NO₃ and LDH 8Mg2Al·NO₃ afforded maximum SO₄^2- adsorption values of 135.14 and 92.59 ​mg/g, respectively. The reaction is best explained by a pseudo-second-order mechanism, which suggests that chemisorption is the rate-determining step. The activation energies of LDH 4Mg2Al·NO₃ and LDH 8Mg2Al·NO₃ indicate that the adsorption of SO₄^2- on synthetic LDHs predominantly follows an anion-exchange mechanism, wherein SO₄^2- ions in the aqueous medium replaces intercalated NO₃^- ions in the synthetic LDHs. The thermodynamic parameters (ΔH̊, ΔS̊, and ΔG̊) were also calculated. The reaction was endothermic, and the synthetic LDHs afforded feasible and spontaneous adsorption of SO₄^2-.     

载体对浸渍型Cu/Mn/Mg/K甲醇裂解催化剂的影响

载体对浸渍型Cu/Mn/Mg/K甲醇裂解催化剂的影响;     

Eco‐friendly magnetic clinoptilolite containing Cu(0) nanoparticles (CuNPs/MZN): as a new efficient catalyst for the synthesis of propargylamines via A3 and KA2 coupling reactions

In this reaserch a new and eco‐friendly magnetic catalyst for the synthesis of propargylamines is reported. Initial incorporation of Fe₃O₄ magnetic nanoparticles (MNPs) into the pores of the natural clinoptilolite zeolite followed by modification with epichlorohydrine and ethylenediamine and then immobilization of CuNPs on the surface of functionalized zeolite gave the desired catalyst (CuNPs/MZN). The CuNPs/MZN was fully characterized by various techniques such as FT‐IR, CHN, TGA, ICP, XRD, SEM, TEM and BET. A host of propargylamines were readily synthesized through using the catalyst in high yields and short reaction times via A³ and KA² coupling reactions of aldehydes/ketones, amines, and phenylacetylene. The CuNPs/MZN was easily separated from the reaction mixture by an external magnet and reused several times successfully. The catalyst has the potential for catalysis of various organic transformations.     

Racemization of chiral amino alcohols III: Effect of Mg or Ca addition on the activity and stability of the Co/γ-Al2O3 catalyst

The racemization of R-(-)-2-amino-1-butanol in a reaction using Co/γ-Al₂O₃ catalysts and catalysts modified by Mg or Ca was investigated in this paper. Complete racemization was achieved with a yield of over 83% at using the Mg modified Co/γ-Al₂O₃ catalyst under optimized reaction conditions of 170°C and 2.5 MPa of H₂. The catalysts were thoroughly characterized by XRD, XPS, TPR, SEM and TEM. The addition of Mg and Ca may be advantageous for dispersing and stabilizing the active species of the Co/γ-Al₂O₃ catalyst, protecting from sintering, significantly improving its catalytic activity and stability.     

Scaled‐up,selective and green synthesis of sulfoxides under mild conditions using (CeIII‐MoVI)Ox/aniline hybrid rods as an efficient catalyst

A novel hybrid material, (Ce^III‐Mo^VI)O_x/aniline, with rod‐like morphology is synthesized through a wet chemical method using Mo₃O₁₀(C₆H₅NH₃)₂.2H₂O nanowires as precursor. The synthesized materials are characterized by XRD, XPS, SEM, TEM, FTIR, Raman, UV–Vis, TGA, and elemental analysis. Also, their catalytic activities as a hybrid catalyst are tested in the selective oxidation of sulfides using hydrogen peroxide as a green oxidant. The proposed novel hybrid catalyst shows an excellent performance under green conditions at mild temperature. Furthermore, the scalability of the oxidation reaction is shown by making multi‐gram quantities at optimized conditions.     

Magnetic Fe3O4/SiO2/NH2 As the Recyclable Heterogeneous Nanocatalyst on Bisphenol-A Recovery from Polycarbonate Wastes

Polycarbonate (PC) wastes received from optical (CDs) and digital optical discs (DVDs) were chemical recycled by using diethylene glycol (DEG) and water as an alternative green solvents and magnetite nanomaterials coated with amine modified silica nanoshell (Fe₃O₄/SiO₂/NH₂) as the recyclable heterogeneous catalyst to recover bisphenol-A (BPA) as a valuable material in 100% yield and without using harmful reagent and environmental problems. The nano-magnetic heterogeneous catalyst can be recycled for four cycles and used next reaction. The recovered BPA and nanomaterials were examined with transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray powder diffraction (XRD), and spectroscopic methods (¹H NMR, ¹³C NMR, FTIR).

     

A practical highly selective oxybromination of phenols with dioxygen

A simple, low cost and highly selective method for the synthesis of mono-bromophenols from phenol and electron-rich phenolic compounds has been developed. Bromide ions are used as halogenating agents, dioxygen as a final oxidant, and Cu(OAc)₂ as a catalyst.     

Preparation of magnetic Fe3O4/P (GMA‐DVB)‐PEI/Pd highly efficient catalyst with core‐shell structure

In this paper, a simple route for palladium (Pd) nanoparticles attached to the surface of hollow magnetic Fe₃O₄/P (GMA‐DVB)‐polyethyleneimine (PEI) microspheres was established. Due to the large amount of imidogen groups and tertiary amine groups presenting in the PEI, Pd²⁺ ions could be anchored to the support by complexation with a polyfunctional organic ligand. Thereafter, a magnetic Pd catalyst having a high loading amount and good dispersibility was obtained by reducing Pd²⁺ ions. Afterwards, the prepared catalyst was characterized by TEM, SEM, FTIR, XRD, TGA, VSM, and UV–vis in detail. Ultimately, their catalytic activity was evaluated using the reduction of 4‐nitrophenol (4‐NP). Research showed that the Fe₃O₄/P (GMA‐DVB)‐PEI/Pd catalyst possessed high catalytic performances for the reduction of 4‐NP with a conversion rate of 98.43% within 540 s. Furthermore, the catalyst could be easily recovered and reused at least for nine successive cycles.     

Synthesis and characterization of <Emphasis Type="Italic">N</Emphasis>-hydroxyphthalimide immobilized on SiO<Subscript>2</Subscript>-coated Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles as magnetic catalyst for oxidation of benzyl alcohols and hydrocarbons

In this study, N-hydroxyphthalimide (NHPI) was successfully attached on functionalized SiO₂-coated Fe₃O₄ nanoparticles through amid bond. The sustained nanomagnetite-immobilized NHPI as a new magnetically recoverable catalyst was characterized by FT-IR, XRD, TGA, VSM, TEM and SEM techniques. The prepared catalyst exhibited high selectivity for oxidation of various benzyl alcohols and hydrocarbons in the presence of hydrogen peroxide as oxidant. The catalyst can be readily separated from the reaction mixture using an external magnet and reused several times without significant loss of its catalytic activity.     

The role of the trivalent metal in an LDH: Synthesis, characterization and fire properties of thermally stable PMMA/LDH systems

Two layered double hydroxides (LDHs), calcium aluminum undecenoate (Ca₃Al) and calcium iron undecenoate (Ca₃Fe), have been prepared by the co-precipitation method. XRD analysis of these LDHs reveals that they are layered materials and FT-IR and TGA confirmed the presence of the undecenoate anions in the material produced. The PMMA composites were prepared by bulk polymerization and the samples were characterized by XRD, TEM, TGA and cone calorimetry. Both additives greatly enhance the thermal stability of PMMA, while the calcium aluminum LDH gives better results when the fire properties were examined using the cone calorimeter.