Solid electrolyte of fully conjugated,water–soluble rigid-rod polymer with articulated backbone for isotropic ionic conductivity

An intractable and fully conjugated, aromatic, heterocyclic rigid-rod polymer poly[1,7-dihydrobenzo[1,2-d:4,5-d′]diimidazo-2,6-diyl-(2-sulfo)-p-phenylene] (sPBI) was derivatized with isophthalic acid for an articulated rigid-rod polymer asPBI. This molecular backbone alternation significantly changed the intrinsic viscosity [η] of sPBI from 9.4 dL/g to 1.1 dL/g for asPBI containing minute (1/50 molar ratio) articulation moiety indicating more a coil-like polymer for asPBI. Both sPBI and asPBI were reacted with 1,3-propanesultone in dimethylsulfoxide containing lithium hydroxide for water–soluble polyelectrolytes sPBI-Li⁺ and asPBI-Li⁺, respectively. The polyelectrolytes were dissolved in aqueous solution with up to 5 wt.% of LiI dopant and cast into films. Direct-current conductivity (σ) was measured at room-temperature parallel to the film surface yielding σ_∥=3.2 × 10⁻³ S/cm and 2.8 × 10⁻³ S/cm for sPBI-Li⁺ and asPBI-Li⁺ (1/15), respectively. X-ray scattering and electron microscopy suggested that the cast films of sPBI-Li⁺ was in-plane isotropic but out-of-the plane anisotropic, and of asPBI-Li⁺ was three-dimensionally isotropic. It suggested that cast films of asPBI-Li⁺ having articulated backbone acquired an isotropic microstructure as well as an isotropic room-temperature σ superior to those of other solid polyelectrolytes.     

Fibriform polyaniline/nano-TiO2 composite as an electrode material for aqueous redox supercapacitors

Fibriform polyaniline/nano-TiO₂ composite is prepared by one-step in situ oxidation polymerization of aniline in the presence of nano-TiO₂ particles, which contains 80% conducting polyaniline by mass, with a conductivity of 2.45 S/cm at 25 °C. Its maximum specific capacitance is 330 F g^?1 at a constant current density of 1.5 A g^?1, and can be subjected to charge/discharge over 10,000 cycles in the voltage range of 0.05–0.55 V.     

Emission color tuning of copolymers containing polyfluorene,benzothiadiazole, porphyrin derivatives

Copolymer containing benzothiadiazole (BT) and porphyrin (POR) derivatives as dopants (<0.3 mol%) was synthesized to polyfluorene (PF) backbone using Suzuki coupling reaction. The synthesized polymer was thermally stable and soluble in general organic solvents. UV–vis spectra of the polymer showed the similar behaviors in solution and on film. However, PL spectra was similar to PF in solution, but its peak increased around 520 and 612 nm as BT and POR, the dopants, went up in casting film. The more POR increased, the more effective Forster energy transfer was observed by POR than BT in PF. The device was made in ITO/PEDOT:PSS/polymer/BaF₂/Ba/Al structure. For PFB02P05 polymer, the luminous efficiency was 0.66 cd/A, the power efficiency 0.29 lm/W and the maximum brightness 936 cd/m². CIE coordinate (0.36, 0.34) was closer to pure white. For PFB15P20, the luminous efficiency was 1.40 cd/A, the power efficiency 0.32 lm/W, the maximum brightness 5997 cd/m². PFB15P20 demonstrated the best performance as green emission.     

Carbazole-modified blue light-emitting copolymers with the backbones integrated by diphenyloxadiazole,fluorene, and triphenylamine

Two new blue light-emitting polymers, poly{[2,5-bis(4-phenylene)-1,3,4-oxadiazole]-[9,9-dihexylfluorene-2,7-diyl]-[N-(4-(9H-carbazol-9-yl)phenyl)-N,N-bis(p-phenylene)aniline]} (POFPA) and poly{[2,5-bis(4-phenylene)-1,3,4-oxadiazole]-[9,9-dihexylfluorene-2,7-diyl]-[4-(3,6-(di-9H-carbazol-9-yl)-9H-carbazol-9-yl)-N,N-bis(p-phenylene)-aniline]} (POFCPA), were synthesized by Suzuki coupling reactions. By GPC analysis against a linear polystyrene standard POFPA and POFCPA were found to have M_n of 1.68 × 10⁴ and 3.70 × 10³, respectively. In contrast to POFPA, the main absorption peak of POFCPA in dilute toluene solution was blue-shifted by Δλ = 26 nm owing to its backbone of relatively shorter π-conjugation length and more carbazole units in side chain. The absolute fluorescence quantum yield (Φ_f) of POFCPA in dilute toluene solution was determined as 73%, much higher than that of POFPA (Φ_f ≈ 58.9%) measured under the same conditions. An electroluminescence device based on POFCPA displays a stable blue emission having color coordinates of (0.15, 0.20), a maximum brightness of 4762 cd/m², and a maximum current efficiency of 1.79 cd/A. By using this polymer as the host material doped with 1 wt.% 4,4′-bis[2-(4-(N,N-diphenylamino)phenyl)vinyl]biphenyl, the achieved highest brightness, maximum current efficiency and maximum power efficiency are 13,613 cd/m², 3.38 cd/A, and1.84 lm/W, respectively.     

A disposable impedance sensor for electrochemical study and monitoring of adhesion and proliferation of K562 leukaemia cells

A polyaniline-modified screen-printed carbon electrode (PANI/SPCE) was prepared by electropolymerization for the construction of a novel disposable cell impedance sensor. The conductive polymer improved greatly the electron transfer of SPCE and was very effective for cell immobilization. The adhesion of cells increased the electron transfer resistance (R_et) of redox probe on the PANI/SPCE surface, producing an impedance sensor for K562 leukaemia cells with a semilogarithm linear range from 10⁴ to 10⁷ cells ml⁻¹ and a limit of detection of 8.32 × 10³ cells ml⁻¹ at 10σ. The proliferation of cells on the conductive polymer increased the R_et, leading to a novel way to monitor the growth process of cells on the PANI/SPCE. The electrochemical monitoring indicated K562 leukaemia cells cultured in vitro on the PANI surface were viable for 60 h, consistent with the analysis from microscopic imaging and MTT assay. This method for monitoring the surface proliferation and detecting the number of viable cells was simple, low-cost and disposable, thus providing a convenient avenue for electrochemical study of cell immobilization, adhesion, proliferation and apoptosis.     

New approaches to improve cycle life characteristics of lithium–sulfur cells

Two different approaches were tried for an improvement of the cycle performance of Li–S cells: (1) A mixed polymer binder system of polyvinyl pyrrolidone (PVP) and polyethyleneimine (PEI) was developed to maintain the initial morphology of the carbon electrodes, the positive electrode of the Li–S cells, during charge–discharge cycles; (2) a tetrabutylammonium (TBA)-based mixed salt system was applied to an organic liquid electrolyte of the Li–S cells to change certain chemical reactions of polysulfides in the electrolyte solutions. The Li–S cells with PEI showed a significant improvement in cycle performance as well as in discharge capacity, compared with the Li–S cells using PVP only. The discharge capacity at the 50th cycle was found to be ∼580 mAh/g-sulfur, 83% of an initial capacity (∼720 mAh/g-sulfur), at a high current density of 2.0 mA cm⁻². It was observed that the Li–S cells with a mixed electrolyte of 0.5 M LiCF₃SO₃/0.5 M TBAPF₆ did not show a distinct improvement in the aspect of discharge capacity. The Li–S cells, however, showed a significant enhancement in the cycle life characteristics much better than that of Li–S cells with 1.0 M LiCF₃SO₃.     

A new solid electrolyte to fill the gap between low temperatures and high temperatures SOFC materials?

According to TG/DTA analysis, the new pyrochlore-type compound K_0.88H_1.12Nb₂O₆·1.58H₂O (Fd-3 m, a = 10.645(4) Å at 300 K) loses crystallization water on heating up to 773 K, but retains –OH hydrogen. Impedance spectroscopy in non-humidified air suggests the material is promising for SOFC applications at intermediate temperatures because the bulk conductivity values reach 10⁻² S/cm at 623 K.     

Using flowerlike polymer–copper nanostructure composite and novel organic–inorganic hybrid material to construct an amperometric biosensor for hydrogen peroxide

A new type of amperometric hydrogen peroxide biosensor was fabricated by entrapping horseradish peroxidase (HRP) in the organic–inorganic hybrid material composed of zirconia–chitosan sol–gel and Au nanoparticles (ZrO₂–CS–AuNPs). The sensitivity of the biosensor was enhanced by a flowerlike polymer–copper nanostructure composite (pPA–FCu) which was prepared from co-electrodeposition of CuSO₄ solution and 2,6-pyridinediamine solution. Several techniques, including UV–vis absorption spectroscopy, scanning electron microscopy, cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy were employed to characterize the assembly process and performance of the biosensor. The results showed that this pPA–FCu nanostructure not only had excellent redox electrochemical activity, but also had good catalytic efficiency for hydrogen peroxide. Also the ZrO₂–CS–AuNPs had good film forming ability, high stability and good retention of bioactivity of the immobilized enzyme. The resulting biosensors showed a linear range from 7.80 × 10^?7 to 3.7 × 10^?3 mol L^?1, with a detection limit of 3.2 × 10^?7 mol L^?1 (S/N = 3) under optimized experimental conditions. The apparent Michaelis–Menten constant was determined to be 0.32 mM, showing good affinity. In addition, the biosensor which exhibits good analytical performance, acceptable stability and good selectivity, has potential for practical applications.     

Anhydrous solid proton conductors based on perfluorosulfonic ionomer with polymeric solvent for polymer electrolyte fuel cell

Novel anhydrous polymeric proton conductors have been prepared from perfluorosulfonic acid ionomer with polymer solvent as supplying proton pathway through the segmental motion of polymer chains for polymer electrolyte fuel cell (PEFC) application. Since the membranes do not contain liquid-state acid or solvent, the membranes may promise more stable performances during the operation of PEFC. The Nafion-based anhydrous proton conductors showed maximum proton conductivity of about 4.0 × 10^?3 S cm^?1 at 130 °C under anhydrous condition. The mechanical properties of the membranes were enhanced by introducing H⁺-doped TiO₂ nanoparticles without the conductivity degradation. In addition, the electrochemical properties of the membrane electrode assembly (MEA) employing the anhydrous membrane as ionomer have been investigated, showing stable open circuit voltages (OCVs) over 0.9 V under non-humidified condition.     

Fabrication of highly conductive Ru/a-CNx:H composite films by anode deposit

Ruthenium(0) composite hydrogenated amorphous carbon nitride (Ru/a-CN_x:H) films were deposition on single crystal silicon (1 0 0) substrate by electrochemical deposition technique with acetonitrile as carbon source, and Ru₃(CO)₁₂ as dopant. In the deposited progress, the Si (1 0 0) acted as anode. The relative atomic ratio of Ru/N/C was about 0.28/0.33/1, and Ru nanocrystalline particles about 8 nm were homogeneously dispersed into the amorphous carbon matrix. After doping Ru into a-CN_x:H films, the conductivity of the films were evidently improved and the resistivity drastically decrease from 10⁸ Ω cm to about 100 Ω cm.     

Molecular spin ladders self-assembly from [Ni(dmit)2]− building blocks: Syntheses,structures and magnetic properties

Two ion-pair compounds, consisting of 1-(4′-R-benzyl)pyridinium ([RBzPy]⁺, R = NO₂ (1) and Br (2)) and [Ni(dmit)₂]⁻ (dmit²⁻ = 2-thioxo-1,3-dithion-4,5-dithiolato), have been synthesized and structurally characterized. The anions of [Ni(dmit)₂]⁻ stack into dimers, which further construct into two-leg ladder through terminal S⋯S interactions in 1, lateral S⋯S interactions in 2. The weak H-bonding interactions of C–H⋯S were observed in 2, while only weak van de Waals interactions between anion and cations in 1. The magnetic susceptibilities measured in 2–300 K indicate AFM exchange interaction domination both two compounds. A peculiar magnetic transition at ∼100 K was observed in 1. An AFM ordering below ∼11 K was found in 2, and the best fit to magnetic susceptibility above 45 K in this compound, using a dimer model with s = 1/2, give rise to Δ/k_B = 36.1 K, zJ = −0.91 K, C = 3.2 × 10⁻³ emu K mol⁻¹ and χ₀ = −4.0 × 10⁻⁶ emu mol⁻¹ with g of 2.0 fixed.     

Stereospecific polymerization of propylene with group 4 ansa-fluorenylamidodimethyl complexes

Group 4 [η¹:η³-tert-butyl(dimethylfluorenylsilyl)amido]dimethyl complexes [t-BuNSiMe₂Flu]MMe₂ (M = Ti, 1; Zr, 2; Hf, 3) were synthesized in a one-pot synthesis starting from the ligand, MeLi and MCl₄ (M = Ti, Zr, Hf), respectively. The structures of these complexes were determined by X-ray crystallography and the results obtained revealed that the fluorenyl ligand coordinates to center metal in a η³-manner irrespective of center metal employed. Propylene polymerization was conducted at 0 or 20 °C in toluene by 1–3 combined with dried methylaluminoxane (MAO), which was prepared from the toluene solutions of MAO by removing free trialkylaluminiums, and HNMe₂PhB(C₆F₅)₄ in the presence of triisobutylaluminium. The 1–dried MAO system gave the polymer with syndiotactic triad (rr) of 63% at 0 °C, whereas 2 and 3 did not give any polymer in the same conditions. The 2–dried MAO system gave the polymer with the highest syndiotacticity (rr = 97%) at 20 °C, although the activity was low. The 3–dried MAO system did not give any polymer even at 20 °C. When HNMe₂PhB(C₆F₅)₄ was used in place of dried MAO at 20 °C, 1 gave almost atactic polymer, while 2 and 3 gave highly syndiotactic one (rr > 90%). These results indicate that the catalytic performance strongly depended on the center metal of the ansa-fluorenylamidodimethyl complexes as well as cocatalysts employed.     

A novel polymeric electrolyte based on a copolymer containing self-assembled stearylate moiety for lithium-ion batteries

A novel polymeric electrolyte based on a self-assembled copolymer moiety has been prepared by a simple method of photo-induced radical polymerization of a mixture consisting of stearylmethacrylate (SMA) and poly(ethylene glycol)-monomethacrylate (PEM) that dissolves LiBF₄ as the electrolytic salt. The SMA moiety work as mechanically stable backbone and the PEM unit dissolving the salts serves as ion-conducting path in the polymeric composite. Solid-state NMR measurements indicated that the resulting polymer composite consists of PEM-rich and SMA-rich phases, each of which exists within several nanometers apart. The ionic conductivity of the polymer electrolyte with the composition of PEM/SMA = 7/3 (by mass ratio) was 2.8 × 10^?5 S cm^?1 at 50 °C, which was significantly higher than that of the polymer electrolyte based on cross-linked PEM copolymer without SMA.     

One-step synthesis of poly(thionine)-Au nano-network and nanowires and its application for non-enzyme biosensing of hydrogen peroxide

We describe the preparation of novel poly(thionine)-Au materials, where the poly(thionine)-Au nano-network and nanowires have been synthesized in aqueous solution via the polymerization of thionine using HAuCl₄ as the oxidant in a single reaction setup. The synthesis process does not require templates, nor does it require large amounts of organic solvents or electrochemical methods. The morphology of the nanocomposites can be controlled by varying the thionine/HAuCl₄ ratio. The resulting poly(thionine)-Au network was used to fabricate a novel non-enzyme hydrogen peroxide (H₂O₂) biosensor. In pH 7.0 phosphate buffer, almost interference-free determination of H₂O₂ was realized at − 0.1 V versus Ag/AgCl with a linear of 1 × 10^− 4 to 5 × 10^− 2 M, a correlation coefficient of 0.998 and a response time of < 2 s. The developed biosensor showed a detection limit of 0.2 μM (S/N = 3) with very good stability, reproducibility and high selectivity.     

Photocurrent generated on a carotenoid-sensitized TiO2 nanocrystalline mesoporous electrode

Photocurrent was observed upon monochromatic illumination of an ITO electrode coated with a TiO₂ nanocrystalline mesoporous membrane with carotenoid 8′-apo-β-caroten-8′-oic acid (ACOA) deposited as a sensitizer (illuminated area 0.25 cm²) and immersed in an aqueous 10 mM hydroquinone (H₂Q), 0.1 M NaH₂PO₄ solution (pH = 7.4) purged with argon, using a platinum flag counter electrode (area 3.3 cm²) and a SCE reference electrode. The carotenoid-sensitized short-circuit photocurrent reached 4.6 μA/cm² upon a 40 μW/cm² incident light beam at 426 nm, with an IPCE (%, incident monochromatic photon-to-photocurrent conversion efficiency) as high as 34%. The short-circuit photocurrent was stable during 1 h of continuous illumination with only a 10% decrease. An open-circuit voltage of 0.15 V was obtained (upon 426 nm, 40 μW/cm² illumination) which remained at a constant value for hours. The observed open-circuit voltage is close to the theoretical value (0.22 V) expected in such a system. The action spectrum resembled the absorption spectrum of ACOA bound on the TiO₂ membrane with a maximum near 426 nm. No decay of the ACOA on the TiO₂ surface was observed after 12 h, presumably because of rapid regeneration of ACOA from ACOA⁺ at the surface by electron transfer from H₂Q.     

Electrospun zirconia-embedded carbon nanofibre for high-sensitive determination of methyl parathion

Carbon nanofibers embedded with ultrafine zirconia nanoparticles (ZrO₂-CNFs) are fabricated via a new methodology. Polyvinylpyrrolidone (PVP) and polymethylmethacrylate (PMMA) binary polymers containing zirconium n-butoxide are first dissolved in dimethylformamide, and the resulting solution is electrospun and heat-treated. The tetragonal zirconia nanoparticles formed, with a size of 5 ± 2 nm in diameter, are uniformly distributed in the carbon nanofibres. Using Nafion as an additive, ZrO₂-CNFs are drop-cast onto the glassy carbon electrode (ZrO₂-CNF/GCE) and the modified electrode is then applied to detect methyl parathion (MP) using differential pulse voltammetry. Two linear relationships are found at the concentration ranges of 1 × 10^− 9–2 × 10^− 8 g/L and 2 × 10^− 8–2 × 10^− 7 g/L, with a detection limit of 3.4 × 10^− 10 g/L (S/N > 3). The electrospun-based ZrO₂-CNF is a very promising coating material for electrochemical sensing of organophosphorus compounds.     

A novel process to prepare porous membranes comprising SnO2 nanoparticles and P(MMA-AN) as polymer electrolyte

We have successfully developed a new process to prepare porous poly(methyl methacrylate-co-acrylonitrile) (P(MMA-AN)) copolymer based gel electrolyte. The porous structure in the polymer matrix is achieved by adding SnO₂ nanoparticles which are mostly used as gas sensor materials. The quasi-aromatic solvent, NMP, has an electron-repulsion effect with the space charge layer on the surface of SnO₂ nanoparticles and forms a special gas–liquid phase interface. Once the cast polymer solution is stored at an elevated temperature to evaporate the solvent, gas–liquid phase separation happens and spherical pores are obtained. The ionic conductivity at room temperature of the prepared gel polymer electrolyte based on the porous membrane is as high as 1.54 × 10⁻³ S cm⁻¹ with the electrochemical stability up to 5.10 V (vs. Li/Li⁺). This method presents another promising way to prepare porous polymer electrolyte for practical use.     

TEMPO addition into pre-irradiated fluoropolymers and living-radical graft polymerization of styrene for preparation of polymer electrolyte membranes

We prepared proton exchange membranes (PEMs) by 2,2,6,6-tetramethylpiperidinyl-1-oxy (TEMPO)-mediated living-radical graft polymerization (LRGP) of styrene into fluoropolymer films and subsequent sulfonation. Poly(vinylidene fluoride) (PVDF) and poly(ethylene-co-tetrafluoroethylene) (ETFE) films were first irradiated and then treated with TEMPO solutions in various solvents. TEMPO addition was confirmed by the test of styrene grafting into TEMPO-treated films at 60 °C, at which the LRGP never proceeds. This test enabled us to differentiate the LRGP from the conventional graft polymerization. In order to gain a deep insight about TEMPO-addition reaction, the TEMPO-penetration behavior into the base polymer films was examined by a permeation experiment and computer simulation. Xylene and dioxane were appropriate solvents for the complete introduction of TEMPO into PVDF and ETFE films, respectively. Then, the LRGP of styrene was performed based on the fully TEMPO-capped films at 125 °C with various solvents. By using an alcoholic solvent, the degree of grafting was enhanced and it reached a maximum of 38%. This grafted film was sulfonated to prepare a PEM showing an ion exchange capacity of 2.2 meq/g and proton conductivity of 1.6×10^?1 S/cm.     

Synthesis of an optically active helical poly(1,3-phenyleneethynylene) bearing stable radicals and its chiroptical and magnetic properties

We synthesized an optically active helical poly(1,3-phenyleneethynylene) with pendant galvinoxyl residues and dimethyl(10-(1S)-pinanyl)silyl groups. The hydrogalvinoxyl precursor polymer was given by polymerization of (1,3-diiodophenyl)hydrogalvinoxyl and 1,3-diethynyl-5-[dimethyl(10-(1S)-pinanyl)silyl]benzene using Pd(PPh₃)₄ catalyst (M_w = 1.7 × 10⁵, M_w/M_n = 3.7). In the CD spectrum taken in ethyl acetate solution, clear Cotton effects were observed in the absorption region of the backbone and hydrogalvinoxyl chromophore, indicating an excess of one-handed helical foldamer conformation. The polymer yielded the corresponding polyradical with high spin concentration by treatment of the polymer solution with PbO₂. The Cotton effects appeared in CD spectra of the polymer and polyradical by addition of methanol to the chloroform solution, although the Cotton effects were hardly observed in chloroform. On the other hand, in the MCD spectra of the polymer and polyradical taken in chloroform solution, Faraday effects were observed in the absorption region of the backbone and galvinoxyl chromophore. The static magnetic susceptibility of the chiral polyradical was measured using a SQUID magnetometer, and showed the antiferromagnetic interaction.