新型半纤维素基磁性水凝胶的制备及性能

采用H₂O₂-Vc氧化还原体系引发半纤维素衍生物,以表面修饰的Fe₃O₄粒子作为磁性组分,利用接枝共聚方法制备了新型半纤维素基磁性水凝胶. 分别用傅里叶变换红外(FTIR)光谱、X射线光电子能谱(XPS)和扫描电子显微镜(SEM)对水凝胶的结构及形貌进行了表征,利用X射线衍射(XRD)和振动样品磁强计(VSM)对水凝胶的晶型结构及磁性能进行了分析,发现Fe₃O₄粒子均匀分散在凝胶网络中,半纤维素基磁性水凝胶表现出良好的顺磁性. 考察了丙烯酸/半纤维素比例、Fe₃O₄粒子含量及交联剂用量对水凝胶溶胀性能的影响,并探讨了该水凝胶的溶胀机理,它在pH 8 缓冲溶液中的溶胀较好符合Fickian 和Schott 动力学模型. 通过SEM和溶胀性能分析表明,随着pH值的升高水凝胶的孔径增大,水凝胶的溶胀率逐渐增大. 制备的水凝胶被用于溶菌酶吸附研究,结果表明磁性凝胶的吸附量大于非磁性水凝胶,水凝胶的吸附行为符合Freundlich 和Temkin 等温模型.     

Preparation of poly(vinylalcohol)/poly(acrylamide‐co‐vinyl imidazole)/γ‐Fe2O3 semi‐IPN nanocomposite and their application for removal of heavy metal ions from water

A series of magnetic semi‐interpenetrating polymer network (semi‐IPN) hydrogels was prepared in one‐stage strategy composed of linear poly(vinyl alcohol) (PVA) chains and magnetic γ‐Fe₂O₃ nanoparticles entrapped within the cross‐linked poly(acrylamide‐co‐vinylimidazole) (poly(AAm‐co‐VI)) network. The influence of PVA, weight ratio of AAm:VI, γ‐Fe₂O₃, and MBA on the swelling properties of the obtained nanocomposite hydrogels was evaluated. The prepared magnetic semi‐IPN hydrogels were fully characterized and used as absorbent for removal of Pb(II) and Cd(II) from water. Factors that influence the metal ion adsorption such as solution pH, contact time, initial metal ion concentration, and temperature were studied in details. The experimental results were reliably described by Langmuir adsorption isotherms. The adsorption capacity of semi‐IPN nanocomposite for Pb(II) and Cd(II) were175.80 and 149.76 mg g^?1, respectively. The kinetic experimental data indicated that the chemical sorption is the rate‐determining step. According to thermodynamic studies, Pb(II) and Cd(II) adsorption on the hydrogels was endothermic and also chemical in nature. The prepared magnetic PVA/poly(AAm‐co‐VI) semi‐IPN hydrogels could be employed as efficient and low‐cost adsorbents of heavy metal ions from water. Copyright © 2016 John Wiley & Sons, Ltd.     

Magnetically assisted removal and separation of cationic dyes from aqueous solution by magnetic nanocomposite hydrogels

Magnetic poly(acrylic acid‐acrylamide‐butyl methacrylate) (P(AAB)) nanocomposite hydrogels were prepared and used as adsorbents for removal and separation of cationic dyes from aqueous solution. These magnetic P(AAB) nanocomposite hydrogels were characterized by scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). It was found that these magnetic P(AAB) nanocomposite hydrogels had magnetic responsive characters. The dynamic swelling, removal, and separation of cationic dye, crystal violet (CV), and basic magenta (BM) by these magnetic nanocomposite hydrogels were studied. The adsorption capacity and isotherm studies of cationic dyes onto magnetic P(AAB) nanocomposite hydrogels have been evaluated. The magnetic P(AAB) nanocomposite hydrogels containing Fe₃O₄ particles can be easily manipulated in magnetic field for removal and separation of cationic dyes from aqueous solution. Adsorption process agreed very well with the Langmuir and Freundlich models. Copyright © 2010 John Wiley & Sons, Ltd.     

Fabrication of 1D Fe3O4/P(NIPAM-MBA) thermosensitive nanochains by magnetic-field-induced precipitation polymerization

One-dimensional (ID) magnetic thermosensitive Fe₃O₄/poly(N-isopropylacrylamide–N,N′-methylenebisacrylamide) (P(NIPAM-MBA)) peapod-like nanochains have been successfully synthesized by magnetic-field-induced precipitation polymerization using Fe₃O₄ as building blocks and P(NIPAM-MBA) as linker. Fe₃O₄ microspheres can be arranged with the direction of an external magnetic field in a line via the dipolar interaction between Fe₃O₄ microspheres and linked permanently via P(NIPAM-MBA) coating during precipitation polymerization. 1D magnetic Fe₃O₄/P(NIPAM-MBA) peapod-like nanochains can be oriented and aligned along the direction of the external magnetic field. More interestingly, Fe₃O₄ microspheres in each peapod were regularly arranged in a line and periodically separated through the P(NIPAM-MBA) layers with a visible interparticle spacing.     

Poly(acrylic acid)‐Modified Fe3O4 Microspheres for Magnetic‐Targeted and pH‐Triggered Anticancer Drug Delivery

Monodisperse poly(acrylic acid)‐modified Fe₃O₄ (PAA@Fe₃O₄) hybrid microspheres with dual responses (magnetic field and pH) were successfully fabricated. The PAA polymer was encapsulated into the inner cavity of Fe₃O₄ hollow spheres by a vacuum‐casting route and photo‐initiated polymerization. TEM images show that the samples consist of monodisperse porous spheres with a diameter around 200 nm. The Fe₃O₄ spheres, after modification with the PAA polymer, still possess enough space to hold guest molecules. We selected doxorubicin (DOX) as a model drug to investigate the drug loading and release behavior of as‐prepared composites. The release of DOX molecules was strongly dependent on the pH value due to the unique property of PAA. The HeLa cell‐uptake process of DOX‐loaded PAA@Fe₃O₄ was observed by confocal laser scanning microscopy (CLSM). After being incubated with HeLa cells under magnet magnetically guided conditions, the cytotoxtic effects of DOX‐loaded PAA@Fe₃O₄ increased. These results indicate that pH‐responsive magnetic PAA@Fe₃O₄ spheres have the potential to be used as anticancer drug carriers.     

Synthesis of Imatinib‐loaded chitosan‐modified magnetic nanoparticles as an anti‐cancer agent for pH responsive targeted drug delivery

Targeted drug delivery is a promising approach to overcome the limitations of classical chemotherapy. In this respect, Imatinib‐loaded chitosan‐modified magnetic nanoparticles were prepared as a pH sensitive system for targeted delivery of drug to tumor sites by applying a magnetic field. The proposed magnetic nanoparticles were prepared through modification of magnetic Fe₃O₄ nanoparticles with chitosan and Imatinib. The structural, morphological and physicochemical properties of the synthesized nanoparticles were determined by different analytical techniques including energy‐dispersive X‐ray spectroscopy (EDS), field emission scanning electron microscopy (FESEM), Fourier‐transform infrared (FTIR) spectroscopy, high resolution transmission electron microscopy (HR‐TEM), vibrating sample magnetometry (VSM), X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS). UV/visible spectrophotometry was used to measure the Imatinib contents. Thermal stability of the prepared particles was investigated and their efficiency of drug loading and release profile were evaluated. The results demonstrated that Fe₃O₄@CS acts as a pH responsive nanocarrier in releasing the loaded Imatinib molecules. Furthermore, the Fe₃O₄@CS/Imatinib nanoparticles displayed cytotoxic effect against MCF‐7 breast cancer cells. Results of this study can provide new insights in the development of pH responsive targeted drug delivery systems to overcome the side effects of conventional chemotherapy.     

Nanosized temperature-responsive Fe3O4-UA-g-P(UA-co-NIPAAm) magnetomicelles for controlled drug release

This paper demonstrated the preparation of temperature-responsive magnetomicelles that consist of a functionalized hexagonal magnetic core, Fe₃O₄-undecylenic acid (Fe₃O₄-UA), and an amphiphilic surface layer of temperature-responsive polymer. The functionalized magnetic Fe₃O₄-UA core was prepared by a suspension-oxidation reaction in an aqueous solution, during which the formation of the Fe₃O₄ and coordination of UA to the Fe₃O₄ occurred simultaneously. Amphiphilic poly(undecylenic acid-co-N-isopropylacrylamide) (P(UA-co-NIPAAm)) was grafted to the Fe₃O₄-UA core as a temperature-responsive micellar surface layer to prepare well dispersed Fe₃O₄-UA-g-P(UA-co-NIPAAm) magnetomicelles with the size of around 8 nm in water. The application of resulted nanosized Fe₃O₄-UA-g-P(UA-co-NIPAAm) magnetomicelles in controlled drug delivery was further investigated and it was found that resulting magnetomicelles exhibited good potential for temperature triggered controlled drug release.     

Tragacanth gum‐based pH‐responsive magnetic hydrogels for “smart” chemo/hyperthermia therapy of solid tumors

The drug delivery performances of pH‐responsive magnetic hydrogels (MHs) composed of tragacanth gum (TG), poly(acrylic acid) (PAA), and Fe₃O₄ nanoparticles (NPs) were investigated in terms of physicochemical as well as biological features. The fabricated drug delivery systems (DDSs) were analyzed using Fourier transform infrared spectroscopy, X‐ray diffraction, vibrating sample magnetometer, scanning electron microscopy, and transmission electron microscopy. The synthesized MHs were loaded with doxorubicin hydrochloride (Dox) as a universal model anti‐cancer drug. The MHs showed excellent Dox loading and encapsulation efficiencies, mainly due to strong hydrogen bonding and electrostatic interaction between the drug and polymeric matrix, as well as porous micro‐structures of the fabricated MHs. The drug‐loaded MHs showed negligible drug release values in physiological condition. In contrast, in cancerous condition (pH 5.0), both MHs exhibited highest drug release values that qualified them as “smart” DDSs. The cytocompatibilities of the MHs as well as the cytotoxicity of the Dox‐loaded MHs were investigated against human epidermoid‐like carcinoma (Hela) cells through MTT assay. In addition, hyperthermia therapy induced by Fe₃O₄ NPs was applied to locally raise temperature inside the Hela cells at 45 ± 3°C to promote cell death. As a result, the Dox‐loaded MHs can be considered as potential DDSs for chemo/hyperthermia therapy of solid tumors.     

The novel composite material MOF-[Mg3(BTC)2]/GO/Fe3O4 and its use in slow-release ibuprofen

This study aimed to synthesize a composite material consisting of metal–organic framework based magnesium(II) and benzene-1,3,5-tricarboxylic acid (H₃BTC) and its modification using graphene oxide (GO) and Fe₃O₄. The obtained material (i.e., [Mg₃(BTC)₂]/GO/Fe₃O₄) was studied as a matrix for the slow release of ibuprofen. [Mg₃(BTC)₂]/GO/Fe₃O₄ matrices were synthesized ex situ with the sonochemical method (material 1) and in situ with the solvothermal method (material 2). The obtained materials were completely characterized by X-ray diffraction and Fourier-transform infrared spectroscopy. Based on scanning electron microscopy imaging, the produced materials were spherical. The presence of GO and Fe₃O₄ in material 1 and material 2 reduced the surface area, but it increased the adsorption capacity of ibuprofen up to 94.12%. The magnetic properties of materials 1 and 2 were observed using a vibrating sample magnetometer. These results demonstrate that modification of Fe₃O₄ nanoparticles induces paramagnetic properties in both materials. The presence of this matrix material was able to release ibuprofen up to seven times slower at pH 5.0 and 12 times slower at pH 7.4. An increase in the pH lead to an increase in the concentration of ibuprofen released to 33.31% more than at pH 5.0.     

Synthesis of multiresponsive β‐cyclodextrin nanocomposite through surface RAFT polymerization for controlled drug delivery

In this study, a unique magnetic, pH, and thermo‐responsive hydrogel nanocomposite was synthesized via surface reversible addition fragmentation chain transfer (RAFT) copolymerization of acrylic acid (AA) and N‐isopropyl acrylamide (NIPAM) in the presence of magnetic β‐cyclodextrin (β‐CD). The nanocomposite demonstrated a pH‐responsiveness behavior at pHs 3 and 9. Moreover, swelling behaviors of nanocomposite were measured in solutions with various temperatures. Furthermore, the nanocomposites exhibited high swelling capacity by applying an external magnetic field because of the presence of Fe₃O₄ nanoparticles in the polymer structure. Besides, the doxorubicin (DOX) loading and releasing behaviors of the hydrogel nanocomposites were studied because of the stimuli‐responsive properties of the synthesized carriers. The adsorption of DOX obeyed a pseudo‐second‐order model and fitted well to the Langmuir isotherm model with the maximum adsorption capacity uptake of 291 mg g^?1. In conclusion, the hydrogel nanocomposites were found to be as potential nanocarriers for use in controlled release applications.     

Fast removal and determination of doxycycline in water samples and honey by Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles

Adsorption characteristics and doxycycline (DC) removal efficiency of Fe₃O₄ magnetic nanoparticles as adsorbents have been determined by investigating the effects of pH, concentration of the DC, amount of adsorbents, contact time, ionic strength and temperature. The mechanism of adsorption was also studied. The adsorption of DC to the Fe₃O₄ magnetic nanoparticles could be described by Langmuir-type adsorption isotherms. Short contact time between the reagents, reusability of Fe₃O₄ for three times after recycling of the nanoparticles, good precision and accuracy, wide working pH range and high breakthrough volume are among the highlights of this procedure. The proposed extraction and determination procedure based on magnetic nanoparticles as adsorbent was successfully applied to the determination of DC spiked in honey and various water samples. The method presented here is fast, simple, cheap and robust, and it does not require the use of organic solvents. Also, the method needs only a magnet and can be performed in any laboratory without sophisticated equipment.     

Fe3O4@SiO2@polymer复合粒子的制备及在药物控制释放中的应用

本文通过多步反应制备了一种新型的、多层结构的、多功能的磁性纳米复合粒子, (Fe₃O₄@SiO₂@polymer). 纳米复合粒子内核是磁性Fe₃O₄纳米粒子, SiO₂包裹在Fe₃O₄上能够使其稳定分散和保护其不被腐蚀氧化; 中间层是生物相容的聚天冬氨酸(PAsp)载药层; 最外层是亲水的聚乙二醇(PEG)稳定层. 磁性纳米复合粒子各层都是生物相容的, 利用静电作用将抗癌药物阿霉素(DOX)负载在磁性纳米复合粒子中, 通过PAsp的pH响应调节了DOX的释放速率.     

Fabrication of liquid crystal Fe3O4 composites and their magnetorheological properties

Some supramolecular polyacrylate-based liquid crystal polymers (PLCPs) were prepared by polyacrylic acid, a liquid crystal monomer and 3,5-pyridinedicarboxylic acid. Series of magnetic liquid crystal particles (Fe₃O₄@PLCPs) with core-shell structure were prepared by modifying surface of magnetic nanoparticles Fe₃O₄ by the PLCPs. The Fe₃O₄@PLCPs showed a saturation magnetization strength above 51.17 emu/g, which is similar to pure magnetic Fe₃O₄, indicating good magnetism and magnetic field dependence. Series of magnetorheological fluids were fabricated by Fe₃O₄@PLCPs (using as dispersed phase) and silicone oil (using as carrier liquid). The effects of mesogen, magnetic particle, and the polymer matrix on magnetorheological performance and settling stability were investigated. The magnetorheological fluid based on 10% Fe₃O₄@PLCP-1 showed the best performance at an applied magnetic field of 100 mT in this study. Furthermore, the magnetorheological fluids showed excellent settling stability because the density of Fe₃O₄@PLCPs was lower than that of Fe₃O₄. The Fe₃O₄@PLCPs-based fluids presented certain application potential in the field of magnetic fluid due to the excellent magnetorheological effect and settling stability.     

Magnetic porous polymer microspheres: Synthesis,characterization and adsorption performance for the removal of phenol

The magnetic poly(ethylene glycol dimethacrylate-n-vinylimidazole) (Fe₃O₄@poly (EGDMA@VIM)) microspheres were prepared by suspension polymerization method using magnetite Fe₃O₄ nano-powder and the porosity, morphology, chemical composition and structure of the magnetic polymer microspheres were characterized. The specific surface area and swelling ratio of the Fe₃O₄@poly(EGDMA@VIM) microspheres were found to be 278.6?m²·g^–1 and 48%, respectively. The Fe₃O₄@poly(EGDMA@VIM) microspheres were used as an adsorbent for phenol removal. The effects of the parameters such as adsorbent dosage, temperature, pH and initial concentration of phenol solutions on the adsorption were investigated. The experimental adsorption equilibrium data obtained were fitted with Langmuir, Freundlich and Dubinin-Radushkevich isotherms and the pseudo-first-order, pseudo-second-order and intra–particle diffusion kinetic models. The adsorption equilibrium data agreed well with the Freundlich isotherm and the pseudo-second-order kinetic model. The maximum capacity of the Fe₃O₄@poly(EGDMA@VIM) microspheres was calculated to be 33.83?mg·g^–1 at 298?K and natural pH from Langmuir isotherm. The Fe₃O₄@poly(EGDMA@VIM) microspheres were found to be reusable for removal of phenol after desorption for several times. The result indicated that the Fe₃O₄@poly(EGDMA@VIM) microspheres are potential candidate for removal of phenol in wastewaters.     

One‐pot synthesis of composite microspheres with core‐shell structure

One‐pot synthesis of thermoresponsive magnetic composite microspheres with a poly(N‐isopropylacrylamide) (PNIPAM) shell and a Fe₃O₄ core is demonstrated. Temperature sensitivity of PNIPAM was adopted to design the novel synthesis pathway. The as‐prepared composite microspheres have an obvious core‐shell structure with a mean size of approximately 250 nm. The Fe₃O₄ core is approximately 5 nm and the thickness of the PNIPAM shell is approximately 10 nm. The content of Fe₃O₄ in the composite microspheres can be controlled by this method. The composite microspheres experience a swelling and shrinking process in water by adjusting the temperature below and above the lower critical solution temperature (LCST) around 32 °C. These microspheres also show fine response to an external magnetic field. This work presents a platform to synthesize organic/inorganic composite microspheres in a facile and efficient approach. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2702–2708     

Synthesis and characterisation of magnetic activated carbon/diopside nanocomposite for removal of reactive dyes from aqueous solutions: experimental design and optimisation

In this work, a series of magnetic activated carbon/nanodiopside (Fe₃O₄/AC/Diop) nanocomposites were synthesised and used for the removal of reactive green KE-4BD dye from the aqueous solution. After preparation of nanodiopside by sol-gel method and activated carbon from coconut husk, first, Fe₃O₄/AC composite was prepared by in situ synthesis of Fe₃O₄ nanoparticles between activated carbon pores, and then, different percentages of Fe₃O₄/AC/Diop nanocomposites were prepared by simple mixing of Fe₃O₄/AC composite and Diop in ethanol. Formation of Fe₃O₄/AC and Fe₃O₄/AC/Diop composites was characterised by FTIR, field emission scanning electron microscopy, BET, XRD and vibrating sample magnetometer analyses. Thermogravimetric analysis was used to show the adsorption capacity of the adsorbent more accurately. Effects of amount of adsorbent, initial pH, contact time and dye concentration on reactive green dye removal were also studied using central composite design. Optimal conditions for maximum reactive green KE-4BD dye adsorption (98.35%) process were as follows: pH= 4.90, adsorbent amount: 0.015 g, dye concentration: 37.17 mg/L and contact time: 10.12 min, respectively. In addition, the adsorption kinetics, thermodynamics and isotherms were examined. Adsorption isotherms (q_max: 344.827 mg/g), kinetics and thermodynamics were demonstrated that the sorption processes were better described by the pseudo-second-order equation and the Langmuir equation.     

Synthesis of Fe3O4@SiO2@polymer nanoparticles for controlled drug release

Novel multifunctional nanoparticles containing a magnetic Fe₃O₄@SiO₂ sphere and a biocompatible block copolymer poly(ethylene glycol)-b-poly(aspartate) (PEG-b-PAsp) were prepared. The silica coated on the superparamagnetic core was able to achieve a magnetic dispersivity, as well as to protect Fe₃O₄ against oxidation and acid corrosion. The PAsp block was grafted to the surface of Fe₃O₄@SiO₂ nanoparticles by amido bonds, and the PEG block formed the outermost shell. The anticancer agent doxorubicin (DOX) was loaded into the hybrid nanoparticles via an electrostatic interaction between DOX and PAsp. The release rate of DOX could be adjusted by the pH value.     

磁性Fe3O4/石墨烯Photo-Fenton催化剂的制备及其催化活性

采用共沉淀法制备磁性Fe3O4/GE(石墨烯)催化剂,实现Fe3O4纳米颗粒生长和氧化石墨烯还原同步进行,采用FTIR、XRD、TEM及低温氮吸附-脱附等对Fe3O4/GE纳米催化剂的物相、颗粒粒径及比表面积进行了表征。在H2O2存在条件下,以亚甲基蓝为目标降解物,考察了在模拟太阳光下Fe3O4/GE的催化活性,当氧化石墨烯与Fe3O4的质量比为1∶10时,经过2 h催化反应,在pH=6条件下,对亚甲基蓝的降解率达到98.7%,经过10次循环使用后对染料溶液的降解率仍保持在95.7%以上,明显优于纯的Fe3O4。     

Thermosensitive and control release behavior of poly(N-isopropylacrylamide-co-acrylic acid)/nano-Fe3O4 magnetic composite latex particle that is synthesized by a novel method

In this study, a novel method was used to synthesize the poly(N-isopropylacrylamide-co-acrylic acid)/Fe₃O₄ (poly(NIPAAm-AA)/Fe₃O₄) magnetic composite latex. The crosslinked poly(NIPAAm-AA) polymer latex particles were first synthesized by the method of soapless emulsion polymerization, then Fe²⁺ and Fe³⁺ ions were introduced to bond with the -COOH groups of AA segments in poly(NIPAAm-AA) polymer latex particles. Further by a reaction with NH₄OH, Fe₃O₄ nanoparticles were generated in situ. The concentrations of acrylic acid (AA), crosslinking agent (N,N′-methylene bisacrylamide (MBA)), and Fe₃O₄ nanoparticles were important factors to influence the morphology and lower critical solution temperature (LCST) of poly(NIPAAm-AA)/Fe₃O₄ magnetic composite latex particles. The poly(NIPAAm-AA)/Fe₃O₄ latex particles were used as a thermosensitive drug carrier to load caffeine. The control release of caffeine was studies. Morphology-based schematic models were proposed to explain the control release behavior of the composite particles with different compositions. Moreover, the protein (albumin, acetylated from bovine serum (BSA)) was bound on the surface of poly(NIPAAm-AA)/Fe₃O₄ composite latex particles. The effects of AA, crosslinking agent and Fe₃O₄ contents on the amount of BSA binding were investigated at different temperatures and pH values. The composition-morphology-BSA conjugation relationship was established.     

Synthesis and characterization of chitosan–polyvinylpyrrolidone–bovine serum albumin-coated magnetic iron oxide nanoparticles as potential carrier for delivery of tamoxifen

The proposed study examined the preparation of chitosan (CS)–polyvinylpyrrolidone (PVP)–bovine serum albumin (BSA)-coated magnetic iron oxide (Fe₃O₄) nanoparticles (Fe₃O₄–CS–PVP–BSA) to use as potential drug delivery carriers for delivery of tamoxifen drug (TAM) . The anticancer drug selected in this study was tamoxifen which can be used for the human breast cancer treatment. These prepared nanoparticles were characterized by FTIR, XRD, SEM, AFM, TEM, CD and VSM techniques. The swelling studies have been measured at different (10, 20, 30, 40, 50%) drug loading. The mean particle size of the tamoxifen-loaded nanoparticles system (Fe₃O₄–CS–TAM, Fe₃O₄–CS–TAM–PVP and Fe₃O₄–CS–TAM–PVP–BSA) as measured by Malvern Zetasizer ranged between 350 ± 2.3 and 601 ± 1.7 nm. As well as these drug-loaded nanoparticles were positively charged. The zeta potential was in the range of 28.9 ± 3.5 and 50.8 ± 3.9 mV. The encapsulation efficiency was between 63.60 ± 2.11 and 96.45 ± 2.12%. Furthermore, in vitro release and drug loading efficiency from the nanoparticles were investigated. The cytotoxicity of prepared nanoparticles was verified by MTT assay. In vitro release studies were executed in 4.0 and 7.4 pH media to simulate the intestinal and gastric conditions and different temperature (37 and 42 °C). Hence, the prepared tamoxifen-loaded nanoparticles system (Fe₃O₄–CS–TAM, Fe₃O₄–CS–TAM–PVP and Fe₃O₄–CS–TAM–PVP–BSA) could be a promising candidate in cancer therapy.