Gas transport properties in thermally cured aromatic polyimide membranes

Aromatic polyimide derived from 2,2′-bis(3,4-dicarboxyphenyl)hexafluoropropane dianhydride (6FDA) and 3,3′-diaminodiphenylsulfone (m-DDS) has been synthesized to facilitate the study of relationships between the polymer structure and the gas transport properties (permeability and selectivity). The gas permeability and selectivity of CO₂, O₂, N₂, and CH₄ for the 6FDA-m-DDS membranes cured at 150, 200, and 250°C have been determined at 35°C and at pressures up to 760 cmHg. The packing density and the fluorescence intensity of the 6FDA-m-DDS polyimide increased sharply with the increasing curing temperature. We propose that this behavior is associated with an increase in intermolecular and/or intramolecular interactions by a charge transfer complex formed in 6FDA-m-DDS containing an alternating sequence of electron donor and electron aceptor molecules. The effect of the microstructure of the thermally cured 6FDA-m-DDS membranes on their gas transport properties is discussed.     

Gas transport properties of annealed polyimide films

Sorption and permeation of CO₂ in various annealed polyimide (PI) films were investigated. Dual-mode sorption and partial immobilization models were used to analyze the data. Sorption of CO₂ in PI film quenched from above the glass transition temperature (T_g) is greater than in film as received. In fact, sorption is decreased over the entire pressure range by cooling the film slowly. These changes in sorption of CO₂ can be attributed to a change in the Langmuir sorption capacity C′_H by annealing, since the other dual-mode sorption parameters, k_D and b, are almost independent of annealing. The value of C′_H is increased by quenching, and decreased by slow cooling from above T_g. The two diffusion coefficients D_D and D_H according to the Henry and Langmuir modes, respectively, for CO₂ also depend markedly on annealing. Diffusion coefficients of quenched PI films are increased and those of film cooled slowly are decreased compared with values for PI film as received. The change in D_H is larger than that in D_D. The permeability coefficient of quenched PI films at 100 cmH_g is about 1.7 times that of PI film as received. The film structure formed by quenching can enhance permselectivity.     

Gas transport properties of asymmetric polyimide membranes prepared by ion‐beam irradiation

Ion beam irradiation has been widely used to modify the structure and properties of membrane surface layers. In this study, the gas permeability and selectivity of an asymmetric polyimide membrane modified by He ion irradiation were investigated using a high vacuum apparatus equipped with a Baratron absolute pressure gauge at 76 cmHg and 35 °C. Specifically, we estimated the effects of the gas diffusion and solubility on the gas permeation properties of the asymmetric membranes with the carbonized skin layer prepared by ion irradiation. The asymmetric polyimide membranes were prepared by a dry–wet phase inversion process, and the surface skin layer on the membrane was irradiated by He ions at fluences of 1 × 10¹⁵ to 5 × 10¹⁵ ions/cm² at 50 keV. The increase in the gas permeability of the He⁺‐irradiated asymmetric polyimide membrane is entirely due to an increase in the gas diffusion, and the gas selectivity increases of the membranes were responsible for the high gas diffusion selectivities. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 262–269, 2007.     

Gas transport properties of polypropylene/clay composite membranes

Polypropylene membranes modified with natural and organically modified montmorillonite clays were prepared. The permeability, diffusivity and solubility of helium, oxygen and nitrogen were determined for the unfilled and filled membranes over the temperature range 25-65 °C. Physical properties of polypropylene membranes were investigated using X-ray diffraction, thermogravimetric analyser, tensile testing and differential scanning calorimetry. The results showed that the filled membranes exhibit lower gas permeability compared to the unfilled polypropylene membrane. For helium, a reduced diffusivity is mainly responsible for the reduction in the permeability, in contrast, for nitrogen and oxygen, both diffusivity and solubility were reduced by the presence of fillers. The X-ray diffraction spectra showed that the incorporation of the unmodified and modified clay did not affect the crystallographic nature of polypropylene.     

Gas transport properties of asymmetric polyimide membranes prepared by plasma‐based ion implantation

In this study, we report the gas permeance and selectivity of the asymmetric polyimide membrane prepared by plasma‐based ion implantation (PBII). The asymmetric polyimide membranes were prepared using a dry–wet phase inversion process, and the surface skin layer on the membrane was implantated by He ions at 2.5 keV. The asymmetric membranes treated by PBII were measured using a high vacuum apparatus with a Baratron absolute pressure gauge at 76 cmHg and 35°C. The (O₂/N₂) and (CO₂/CH₄) selectivities in the He⁺‐implanted asymmetric membrane at 60 sec resulted in 1.5 and 1.8 time increases, respectively, when compared to those of the asymmetric membrane before PBII. On the other hand, the O₂ and CO₂ permeances in the asymmetric membrane after PBII decreased with an increase in the He⁺ treatment time. In this paper, we addressed, for the first time, the gas permeation behavior of the asymmetric polyimide membranes prepared by PBII. Copyright © 2009 John Wiley & Sons, Ltd.     

Interrelation between phase state and gas permeation in polysulfone/polyimide blend membranes

The phase state of polysulfone/polyimide (PSF/PI) blends has been studied by differential scanning calorimetry, rheology, and X-ray scattering. The blends rich in PSF form miscible blends when prepared by solution casting from a common solvent. In these PSF-rich blends, the single dynamic process in rheology shifts and broadens, with composition reflecting the change in local friction and the enhancement of concentration fluctuations, respectively. Heating to temperatures above the glass transition temperature results in phase separation into PSF- and PI-rich domains. An apparent phase diagram has been constructed, and helium permeability has been measured in different regimes corresponding to miscible, partially miscible, and completely phase-separated states. We find that one component (PI) controls the permeability values and activation energies for helium permeation in the blends. Gas permeation is found to be very sensitive to local concentration fluctuations and thus can be used as a probe of the phase state in polymer blends. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2788–2798, 1999     

Gas permeation through PSF-PI miscible blend membranes

The permeation rates of He, H₂, CO₂, N₂ and O₂, are reported for a series of miscible polysulfone-polyimide (PSF-PI) blend membranes synthesized in our laboratory. For gases which do not interact with the polymer matrix (such as He, H₂, N₂ and O₂), gas permeabilities in the miscible blends vary monotonically between those of the pure polymers and can be described by simple mixture equations. In the case of CO₂, which interacts with PI, blend permeabilities decrease somewhat, compared to pure PSF and PI. This, however, is accompanied by a two-fold improvement in the critical pressures of plasticization vs. polyimide. Permselectivities of CO₂/N₂ and H₂/CO₂ in the blends deviate from mixing theory predictions, in contrast to selectivities of gas pairs which do not interact with PI. Differential scanning calorimetry measurements of pure and PSF/PI blend membranes show one unique glass transition temperature, supporting the miscible character of the PSF/PI mixture. Optical micrographs of the blend membranes clearly indicate perfect homogenization and no phase separation. Frequency shifts and absorption intensity changes in the FTIR spectra of the blends, as compared with those of the pure polymers, indicate mixing at the molecular level. This compatibility in mixing PSF and PI, results essentially in a new blend polymer material, suitable for the preparation of gas separation membranes. Such membranes combine satisfactory gas permeation properties, reduced cost, advanced resistance to harsh chemical and temperature environments, and improved tolerance to plasticizing gases.     

Gas transport properties of poly(ethylene oxide-co-epichlorohydrin) membranes

Gas permeation properties of crosslinked membranes prepared from a series of poly(ethylene oxide-co-epichlorohydrin) (P(EO/EP)) copolymers with different contents of ethylene oxide are determined by using the constant-volume and pressure-increase method. In addition to the chemical composition, the transport properties are related to the main characteristics of copolymers like the glass transition temperature, crystallinity and crosslinking ratio. Permeation measurements of He, H₂, N₂, O₂, CO₂ and CH₄ show that the permeabilities are nearly constant up to an EO content of about 75–80 mol%, then increase rapidly up to a maximum around 90 mol% of EO in the copolymers. The same behavior is observed for the diffusion coefficient and the CO₂ sorption coefficient. The presence of an optimal EO composition is explained by the competition between crystalline and amorphous EO sequences. The copolymers present very high CO₂ permeability and selectivity respect to other permanent gases even in gas mixtures and under high pressures.     

Gas permeation properties of asymmetric carbon hollow fiber membranes prepared from asymmetric polyimide hollow fiber

Asymmetric carbon hollow fiber membranes were prepared by pyrolysis of an asymmetric polyimide hollow fiber membrane, and their mechanical and permeation properties were investigated. The carbon membrane had higher elastic modulus and lower breaking elongation than the polyimide membrane. Permeation experiments were performed for single gases such as H₂, CO₂, and CH₄, and for mixed gases such as H₂/CH₄ at high feed pressure ranging from 1 to 5 MPa with or without toluene vapor. The permeation properties of the carbon membranes and the polyimide membrane were compared. There was little change in the properties of the carbon membranes with a passage of time. The properties were hardly affected by the feed pressure, whether the feed was accompanied with the toluene vapor or not, because the carbon membranes were not affected by compaction and plasticization.     

Study of the casting of sulfonated polyimide ionomer membranes: structural evolution and influence on transport properties

A casting process has been studied for charged polymers: the sulfonated polyimide ionomer membrane. The formation of the membrane has been followed by X-ray reflectivity as a function of temperature. The effect of equivalent weight has been also investigated. The thickness loss presents two regimes: the first one is linear vs time indicating that the models developed for noncharged polymer may be suitable for ionomers in the early period of drying. The second one corresponds to the loss of X-ray reflectivity signal. Moreover, the X-ray reflectivity signal seems to be correlated to the characteristic time of the sample drying. In complement, we have studied the influence of casting on the properties of the dried ionomer membranes. The transport coefficients of N(CH(3))(4)(+) ions confined in two kinds of membranes that were differently cast were measured. The results show that shearing the ionomer solution during casting may lead to an enhancement of the anisotropy of structure and of transport. Moreover, we have studied the effect of both interfaces on the ion transport properties through the dried membranes.     

Pervaporation properties of EC membranes modified by aliphatic hyperbranched polyester

Pervaporation membranes containing hyperbranched polymer were prepared from the blends of ethyl cellulose (EC) and hyperbranched polyester (HBPE). The FT-IR analysis indicated that the interactions between EC and HBPE decreased as increasing the generation of HBPE. The membrane containing HBPE (EC-HBPE) showed both higher sorption ratio and selectivity than pure EC membrane. The effects of HBPE content as well as temperature of feed solutions on the membrane performance were investigated in detail. The EC-HBPE membrane exhibited much higher permeate flux than the EC membrane, while the separation factor maintained at same level.     

Characterization and transport properties of Nafion/polyaniline composite membranes

Nafion membranes were modified by chemical polymerization of aniline using ammonium peroxodisulfate as the oxidant. The Nafion-polyaniline composite membranes were extensively characterized using scanning electron microscopy (SEM), atomic force microscopy (AFM), infrared (FTIR-ATR) and X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and ion-exchange capacity measurements. The transport properties were also evaluated by conductivity and electrodialysis measurements. The data show that when a high oxidant concentration (1 M (NH4)2S2O8) is used, polyaniline is mostly formed at the surface of the Nafion membrane with a higher proportion of oligomers. On the contrary, when 0.1 M oxidant is used, polyaniline is mostly formed inside the ionic domains of Nafion, blocking the pathway to ion transport and thus reducing the transport of Zn2+ as well as the transport of H+. These data were also compared to the data obtained with poly(styrene sulfonate)-PANI composite membranes.     

Gas transport properties of 6FDA-TMPDA/MOCA copolyimides

The gas permeation behavior of 2,2′-bis(3,4′dicarboxyphenyl) hexafluoropropane dianhydride(6FDA)-2,4,6-trimethyl-1,3-phenylenediamine (TMPDA)/4,4′-methylene bis(2-chloroaniline) (MOCA) copolyimides was investigated by systematically varying the diamine ratios. All the copolyimides were soluble in most of the common solvents. The gas permeabilities and diffusion coefficients decreased with increasing MOCA content; however, the permselectivity of gas pairs such as H₂/N₂, O₂/N₂, CO₂/CH₄ was enhanced with the incorporation of MOCA moiety. Moreover, all of the copolyimides studied in this work exhibited performance near, lying on or above the existing upper bound trade-off line between permselectivity and permeability.     

Sulfonated dendrimer‐ and hyperbranched polyglycerol‐PBIOO® blend membranes for fuel cells

A new sulfonated dendrimer with an arylene ether sulfone backbone has been synthesized, fully characterized, and blended with PBIOO^® to prepare acid‐base proton‐conducting membranes under different conditions and with different composition ratios. Water‐soluble sulfonated hyperbranched polyglycerols of different molecular weights were also used as the acidic components. Membrane properties such as ion‐exchange capacity, water uptake, thermal stability, proton conductivity, and morphology have been studied and discussed. The nature of the acidic component and the morphology of the membranes had a marked influence on the final properties. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 69–80     

Gas transport properties of thin polymeric membranes in the presence of silicon dioxide particles

The fundamental gas transport properties of thin films of six high performance polymers were evaluated in the presence of silicon dioxide particles. The silica particles were brought in close contact with the polymer inside the 200 Å. (DIA) pores of Anopore™ aluminum oxide membranes. This unique environment allows intimate contact between the polymer and the silica particles. The presence of silica improves the gas separation properties of the permselective layer, particularly for oxygen and nitrogen. The increase in O₂/N₂ selectivity for some membranes is accompanied by an increase in oxygen permeability. The oxygen/nitrogen separation properties of the polymers in the presence of silica falls above the so-called “upper limit” of performance reported for polymeric materials. The observed significant increases in the glass transition temperature suggest restriction of chain segmental mobility possibly due to adsorption of polymer to silica surface. The increase in the activation energy of permeation points to increases in energetics of diffusion as the reason for the improved selective permeation. The observed behavior was not limited to oxygen and nitrogen as demonstrated by the results for other gas pairs tested.     

Properties and morphologies of UV‐cured epoxy acrylate blend films containing hyperbranched polyurethane acrylate/hyperbranched polyester

The properties and morphologies of UV‐cured epoxy acrylate (EB600) blend films containing hyperbranched polyurethane acrylate (HUA)/hyperbranched polyester (HPE) were investigated. A small amount of HUA added to EB600 improved both the tensile strength and elongation at break without damaging its storage modulus (E′). The highest tensile strength of 31.9 MPa and an elongation at break around two times that of cured pure EB600 were obtained for the EB600‐based film blended with 10% HUA. Its log E′ (MPa) value was measured to be 9.48, that is, about 98% of that of the cured EB600 film. The impact strength and critical stress intensity factor (K_1c) of the blends were investigated. A 10 wt % HUA content led to a K_1c value 1.75 times that of the neat EB600 resin, and the impact strength of the EB600/HPE blends increased from 0.84 to 0.95 kJ m^?1 with only 5 wt % HPE addition. The toughening effects of HUA and HPE on EB600 were demonstrated by scanning electron microscopy photographs of the fracture surfaces of films. Moreover, for the toughening mechanism of HPE to EB600, it was suggested that the HPE particles, as a second phase in the cured EB600 film, were deformed in a cold drawing, which was caused by the difference between the elastic moduli of HPE and EB600. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3159–3170, 2005