Cationic concentration effects on electron beam cured of carbon-epoxy composites

Electron beam (e-beam) curing is a technology that offers advantages over the thermal curing process, that usually requires high temperature and are time-consuming. E-beam curing is faster and occurs at low temperatures that help reduce residual mechanical stresses in a thermoset composite. The aim of the present study is to analyze the effects of cationic initiator (diaryliodonium hexafluoroantimonate) ranged from 1 to 3 wt% in DGEBA (diglycidyl ether of bisphenol A) epoxy resin when cured by a 1.5 MeV electron beam. The specimens were cured to a total dose of 200.4 kGy for 40 min. Analyses by dynamic mechanical thermal analysis (DMTA) and differential scanning calorimetry (DSC) show that the e-beam irradiated samples with 2 wt% cationic initiator were 96% cured obtained a glass transition temperature (tan δ) of 167 °C. The same epoxy resin, thermally cured for 16 h with an anhydride hardener, reached a T_g (tan δ) of 136 °C. So, the irradiated sample had its T_g increased approximately 20% and the curing process was much less time consuming.     

Synthesis and characterization of photocrosslinkable poly(l-lactide)s with a pendent cinnamate group

In this report, we describe the synthesis and characterization of photosensitive poly(l-lactide) with a pendent cinnamate group. α,ω-Dihydoxy terminated poly(l-lactide) (PLLA-diol) [molecular weights (MW); 2000, 4000 and 9000 g/mol ] was chain-extended with a diacyl chloride of 5-cinnamoyloxyisophthalic acid (ICA) to obtain high-molecular-weight photocrosslinkable poly(l-lactide)s (ICA/PLLA). The resulting polyesters were characterized by proton nuclear magnetic resonance spectroscopy, gel permeation chromatography, ultraviolet–visible spectroscopy, differential scanning calorimetry, thermomechanical analysis and thermogravimetry. The glass transition temperature (T_g), the melting temperature (T_m) and the degree of relative crystallinity (X_c) of ICA/PLLAs increased with the increasing MW of the PLLA-diols. The photosensitive ICA/PLLAs were irradiated with a 400 W high-pressure mercury lamp (λ > 280 nm) for various times to produce the PLLA gel films without a photoinitiator. The crosslinking rate monitored by a UV–vis spectrum decreased with the increasing MW of the PLLA-diols. The crosslinking of the ICA/PLLA ?4000 film enhanced the T_g slightly and the tensile strength and Young’s modulus significantly, while reduced the T_m and X_c. The enzymatic degradation was measured by the weight loss of the films in a phosphate buffer solution with proteinaze-k. The crosslinking of the films decreased markedly the degradation rate.     

Thermodynamic study on the sublimation of six methylnitrobenzoic acids

The Knudsen mass-loss effusion technique was used to measure the vapour pressures at different temperatures of the following six compounds: 2-methyl-3-nitrobenzoic acid, between T =  357.16 K and T =  371.16 K; 2-methyl-6-nitrobenzoic acid, between T =  355.16 K and T =  369.16 K; 3-methyl-2-nitrobenzoic acid, between T =  371.16 K and T =  385.14 K; 3-methyl-4-nitrobenzoic acid, between T =  363.21 K and T =  379.16 K; 4-methyl-3-nitrobenzoic acid, between T =  363.10 K and T =  377.18 K; 5-methyl-2-nitrobenzoic acid, between T =  355.18 K and T =  371.08 K. From the temperature dependence of the vapour pressure, the standard molar enthalpies of sublimation were derived by the Clausius–Clapeyron equation and the molar entropies of sublimation at equilibrium pressures were calculated. Using estimated values for the heat capacity differences between the gas and the crystal phases of the studied compounds the standard, p^o =  10⁵Pa, molar enthalpies Δ_cr^gH_m^o, entropies Δ_cr^gS_m^oand Gibbs energies Δ_cr^gG_m^oof sublimation at T =  298.15 K, were derived:     

Diffusion coefficients of nickel chloride in aqueous solutions of lactose at T = 298.15 K and T = 310.15 K

Binary mutual diffusion coefficients (interdiffusion coefficients) of nickel chloride in water at T = 298.15 K and T = 310.15 K, and at concentrations between (0.000 and 0.100) mol · dm^?3, using a Taylor dispersion method have been measured. These data are discussed on the basis of the Onsager–Fuoss and Pikal models. The equivalent conductance at infinitesimal concentration of the nickel ion in these solutions at T = 310.15 K has been estimated using these results. Through the same technique, ternary mutual diffusion coefficients (D₁₁, D₂₂, D₁₂, and D₂₁) for aqueous solutions containing NiCl₂ and lactose, at T = 298.15 K and T = 310.15 K, and at different carrier concentrations were also measured. These data permit us to have a better understanding of the structure of these systems and the thermodynamic behaviour of NiCl₂ in different media.     

Thermodynamic study of the system (LiCl + LiNO3 + H2O)

The solubility of the binary system (LiNO₃ + H₂O) from T = 273.15 K to T = 333.15 K and solubility isotherms of the ternary system (LiCl + LiNO₃ + H₂O) were elaborately measured at T = 273.15 K and T = 323.15 K. These solubility data, as well as water activities in the binary systems from the literature, were treated by an empirically modified BET model. The isotherms of the ternary system (LiCl + LiNO₃ + H₂O) were reproduced and a complete phase diagram of the ternary system in the temperature range from 273.15 K to 323.15 K predicted. It is shown that the solubility data for the binary system (LiNO₃ + H₂O) measured in this work are slightly different from the literature data. Simulated results showed that the saturated salt solution of (2.8LiCl + LiNO₃) is in equilibrium with the stable solid phase LiNO₃(s) over the temperature range from 283.15 K to 323.15 K, other than the solid phases LiNO₃ · 3H₂O(s) and LiClH₂O(s) as reported by Iyoki et al. [S. Iwasaki, Y. Kuriyama. T. Uemura, J. Chem. Eng. Data 38 (1993) 396–398].     

Short chain lead (II) alkanoates as ionic liquids and glass formers: A d.s.c., X-ray diffraction and FTIR spectroscopy study

Three members of the lead (II) n-alkanoates (from etanoate to n-butanoate) have been synthesized, purified and studied by d.s.c., X-ray diffraction, and FTIR spectroscopy. Lead (II) acetate, propanoate, and butanoate present only a melting transition at T = (452.6, 398.2, and 346.5) K, with Δ_fH = (16.0, 13.1, and 15.6) kJ · mol⁻¹, and Δ_fS = (35.3, 32.8, and 45.1) J · mol⁻¹ · K⁻¹, respectively. These temperature data correct to a great extent the historical values reported in the literature. These three members readily quench into a glass state. Their corresponding T_g values are (314.4, 289.0, and 274.9) K, respectively, measured by d.s.c. at a heating rate of 5 K · min⁻¹.     

Volumetric study of (2-methoxyethanol + tetrahydrofuran + cyclohexane) at T=298.15 K

The excess molar volumes V_m^E at T=298.15 have been determined in the whole composition domain for (2-methoxyethanol + tetrahydrofuran + cyclohexane) and for the parent binary mixtures. Data on V_m^E are also reported for (2-ethoxyethanol + cyclohexane). All binaries showed positive V_m^E values, small for (methoxyethanol + tetrahydrofuran) and large for the other ones. The ternary V_m^E surface is always positive and exhibits a smooth trend with a maximum corresponding to the binary (2-methoxyethanol + cyclohexane). The capabilities of various models of either predicting or reproducing the ternary data have been compared. The behaviour of V_m^E and of the excess apparent molar volume of the components is discussed in both binary and ternary mixtures. The results suggest that hydrogen bonding decreases with alcohol dilution and increases with the tetrahydrofuran content in the ternary solutions.     

Density and activity of pertechnetic acid aqueous solutions at T = 298.15 K

The previous isopiestic investigations of HTcO₄ aqueous solutions at T = 298.15 K are believed to be unreliable, because of the formation of a ternary mixture at high molality. Consequently, published isopiestic molalities for aqueous HTcO₄ solutions at T = 298.15 K were completed and corrected. Binary data (variation of the osmotic coefficient and activity coefficient of the electrolyte in solution in the water) at T = 298.15 K for pertechnetic acid HTcO₄ were determined by direct water activity measurements. These measurements extend from molality m = 1.4 mol · kg⁻¹ to m = 8.32 mol · kg⁻¹. The variation of the osmotic coefficient of this acid in water is represented mathematically. Density variations at T = 298.15 K are also established and used to express the activity coefficient values on both the molar and molal concentration scale. The density law leads to the partial molar volume variations for aqueous HTcO₄ solutions at T = 298.15 K, which are compared with published data.     

Thermodynamic study on the sublimation of 3-phenylpropionic acid and of three methoxy-substituted 3-phenylpropionic acids

The Knudsen mass-loss effusion technique was used to measure the vapour pressures at different temperatures of the following compounds: 3-phenylpropionic acid, between T =  305.17 K and T =  315.17 K; 3-(2-methoxyphenyl)propionic acid, between T =  331.16 K and T =  347.16 K; 3-(4-methoxyphenyl)propionic acid, between T =  341.19 K and T =  357.15 K; 3-(3,4-dimethoxyphenyl)propionic acid, between T =  352.18 K and T =  366.16 K. From the temperature dependence of the vapour pressure, the standard molar enthalpies of sublimation Δ_cr^gH_m^owere derived by the Clausius–Clapeyron equation and the molar entropies of sublimation at equilibrium pressures were calculated. On the basis of estimated values for the heat capacity differences between the gas and the crystal phases of the studied compounds the standard, p ^∘  =  10⁵Pa, molar enthalpies, entropies and Gibbs energies of sublimation at T =  298.15 K, were derived:     

Preferential crystallization in an unusual case of conglomerate with partial solid solutions

Ethanolamine mandelate (E.M.) crystallizes as a stable conglomerate and has been found to form partial solid solutions. The crystal structure of the pure enantiomer has been solved from single-crystal X-ray diffraction. In order to determine the extreme compositions of the partial solid solutions in equilibrium (87% ee), the isothermal ternary section in the system [(+)-E.M.–(−)-E.M.–(ethanol–water azeotropic mixture)] was established at 25 °C. Several consecutive preferential crystallization attempts (AS3PC method) were undertaken between T_B = 41 °C (starting temperature) and T_F = 25 °C (final temperature) on a 2-L scale.We initially expected to obtain crude crops whose enantiomeric purities would be close to that defined by the isothermal ternary phase diagram (T_F). In fact, the filtered solid phases are of lower enantiomeric excesses: ca. 62% ee. The monitoring of the mother liquor composition over the course of the entrainment shows that the enantiomeric composition of the filtered solid is related to the metastable equilibria involved in the preferential crystallization.     

Achieving high-rate capacitance of multi-layer titanium carbide (MXene) by liquid-phase exfoliation through Li-intercalation

The stacks of multi-layer Ti₃C₂T_x and other types of MXene materials limit their electrochemical performance. Herein, we report a facile exfoliation technique to improve the exfoliation efficiency through Li-intercalation into Ti₃C₂T_x interlayers in isopropyl alcohol (IPA) with LiOH as intercalant. This de-intercalation method presented here not only effectively delaminates the stacked Ti₃C₂T_x multi-layers into separate few-layer MXene sheets, but also achieves high-rate supercapacitive performance of Ti₃C₂T_x electrode. The as-produced delaminated Ti₃C₂T_x shows highly improved electrochemical capacitive properties from 47 to 115 F g^− 1 at 200 mV s^− 1. Even at extremely high scan rate of 1000 mV s^− 1, a specific capacitance of 82 F g^− 1 is still obtained. The high-rate capability can be attributed to improved ions accessibility into the few-layer structures. This study offers a new and simple exfoliation pathway for MXenes materials to exploit their full potential in energy storage applications.     

On the stability and properties of the polyacrylate/Na-MMT nanocomposite obtained by seeded emulsion polymerization

For high performance waterborne coatings usually polymer latexes with low emulsifier content are more preferred. Although polymer/clay nanocomposites offer improved properties, it is difficult to produce clay based nanocomposite latexes containing low emulsifier due to the stabilization problems especially caused by organoclays. Present study deals with the preparation of a tBA/BA/MAA ternary copolymer/clay nanocomposite containing 3 wt.% sodium montmorillonite (Na⁺-MMT) via seeded emulsion polymerization. Experimentally it was observed that even the usage of hydrophilic clay caused stabilization problem and a certain amount of emulsifier (>1 wt.%) was necessary to obtain stable latexes. In addition, the usage of a low molecular weight water soluble polymer as steric barrier was found to increase the stability of system. Obtained nanocomposite latex showed fine particle size diameter (127 nm) and very narrow size distribution (PDI = 0.06). The WAXD and TEM investigations indicated that a mostly exfoliated nanocomposite was obtained. Thermal analyses (DSC, DMTA and TGA) showed that there was no change at T_g of the copolymer while very high improvement was obtained for elastic modulus and a slight increase in thermal stability. According to the rheological measurements, the nanocomposite latex showed a higher low shear viscosity, a stronger shear thinning behavior and an improved physical stability in comparison to the reference latex.     

Thermodynamic study of the system (LiCl + CaCl2 + H2O)

Solubility isotherms of the ternary system (LiCl + CaCl₂ + H₂O) were elaborately determined at T = (283.15 and 323.15) K. Several thermodynamic models were applied to represent the thermodynamic properties of this system. By comparing the predicted and experimental water activities in the ternary system, an empirical modified BET model was selected to represent the thermodynamic properties of this system. The solubility data determined in this work at T = (283.15 and 323.15) K, as well as those from the literature at other temperatures, were used for the model parameterization. A complete phase diagram of the ternary system was predicted over the temperature range from (273.15 to 323.15) K. Subsequently, the Gibbs free energy of formation of the solid phases CaCl₂ · 4 H₂O_(s), CaCl₂ · 2 H₂O_(s), LiCl · 2H₂O_(s), and LiCl · CaCl₂ · 5H₂O_(s) was estimated and compared with the literature data.     

Contribution to study of the thermodynamics properties of mixtures containing 2-methoxy-2-methylpropane,alkanol, alkane

Excess molar enthalpies for the ternary system {x₁ 2-methoxy-2-methylpropane (MTBE) + x₂ 1-pentanol + (1 − x₁ − x₂) hexane} and the involved binary mixture {x 1-pentanol + (1 − x) hexane}, have been measured at T = 298.15 K and atmospheric pressure over the whole composition range. We are not aware of the existence of previous experimental measurement of the excess enthalpy for the ternary mixture under study in the literature currently available. Values of the excess molar enthalpies were measured using a Calvet microcalorimeter. The results were fitted by means of different variable degree polynomials. The ternary contribution to the excess enthalpy was correlated with the equation due to Verdes et al. (2004), and the equation proposed by Myers–Scott (1963) was used to fit the experimental binary mixture measured in this work. Smooth representations of the results are presented and used to construct constant excess molar enthalpy contours on Roozeboom diagrams. The excess molar enthalpies for the binary and ternary system are positive over the whole range of composition. The binary mixture {x 1-pentanol + (1 − x) hexane} is asymmetric, with its maximum displace toward a high mole fraction of decane. The ternary contribution is also positive with the exception of a range located around the rich compositions of 1-pentanol, and the representation is asymmetric.Additionally, the group contribution model of the UNIFAC model, in the versions of Larsen et al. (1987) [18] and Gmehling et al. (1993) [19] was used to estimate values of binary and ternary excess enthalpy. The experimental results were used to test the predictive capability of several empirical expressions for estimating ternary properties from binary results.     

Jahn–Teller coupling and the influence of strain in Tg and Eg ground and excited states – A ligand field and DFT study on halide MIIIX6 model complexes [M = TiIII–CuIII; X = F−, Cl−]

In contrast to well established experimental results of vibronic coupling effects in octahedral dⁿ complexes with E_g ground states (Cu²⁺, Ag²⁺; Cr²⁺, Mn³⁺ etc.), not much useful material is available for the Jahn–Teller (JT) effect in orbital triplet ground states. The present study is concerned with this deficiency, providing data for octahedral halide model complexes with 3dⁿ cations – in particular for Ti^III, V^III and high-spin Co^III, Ni^III with T_2g and T_1g ground states, which involve, to first-order, solely splitting of the π-antibonding t_2g MOs. Besides experimental results – structural and spectroscopic, mainly from d–d spectra – data from computations are needed for a quantitative treatment of the T_g ? (?_g + τ_2g) vibronic interaction as well as in the E_g ? ?_g coupling case (Mn^III, low-spin Ni^III); DFT was the method of choice, if only critically selected outcomes are utilised. The theoretical bases of the treatment are the dⁿ ligand field matrices in O_h, extended by the inclusion of lower-symmetry distortion parameters, and the conventional theory of vibronic coupling. Caution is needed when classifying the effects of interelectronic repulsion; DFT does not reproduce the magnitudes of the Racah parameters B, C, as deduced from the d–d spectra, properly – the presumed reasons are analysed. DFT even allows one to deduce reliable vibronic coupling constants via the analysis of orbitally degenerate excited states (Cr^III, ⁴A_2g ground state). The group-theoretical analysis of the interaction with the JT-active ?_g and τ_2g modes yields D_4h, D_3d and D_2h as the possible distortion symmetries in the case of a T_g ground state. The DFT-calculations give clear evidence, that the D_4h stationary points represent the absolute minima in the T_g ? (?_g + τ_2g) potential surface – in agreement with experiment, where available. For the first time, vibronic coupling constants, characterising JT splitting of ground and excited T_g states, can be presented for trivalent 3dⁿ cations in octahedral halide ligand fields. They turn out to be smaller by a factor of almost 3 in comparison to those, which determine the coupling in σ-antibonding e_g MOs.The tetragonal splitting of T_g states is typically only small, around 0.1 eV, and suggests that strain influences from a specific ligand arrangement and/or the presence of different ligands may modify the potential surface considerably. We have studied such effects via compounds A^IM^IIIF₄, where an elastic strain induced by the host structure, and a binding strain, due to the simultaneous existence of (largely) terminal and of bridging ligands, are active. A novel strain model, in its interplay with JT coupling, is proposed and applied – using energies from the d–d spectra, structural results and data from DFT.Chloride complexes are only known for Ti^III to Fe^III; the rather small electronegativity already of Co^III suggests a reducing ligand-to-metal (3dⁿ) electron transfer for n ≥ 6. Similarly, the low-lying ligand-to-metal charge transfer bands in the d–d spectra of the Cu^IIIF₆^3? complex and the reduced T_g ? ?_g coupling strength suggest a pronounced covalency of the Cu^III–F, and, even more distinctly, of the Cu^III–O bond, which is of interest for superconductivity. The Ni^IIIF₆^3? polyhedron possesses a low-spin configuration in the elpasolite structure. The spectroscopic evidence and the DFT data indicate, that the minimum positions of the alternative _a²A_1g(_a²E_g) and _a⁴A_2g (_a⁴T_1g) potential curves are only ≤0.02 eV apart, giving rise to interesting high-spin/low-spin phenomena. It is the strong E_g ? ?_g as compared to the T_1g ? ?_g coupling, which finally stabilises a spin-doublet ground state in D_4h.We think, that the selected class of solids is unique particularly for the study of Jahn–Teller coupling in T ground states, with model character for other systems. In our overview a procedure is sketched, which uses reliable computational results (here from DFT) for supplementing incomplete experimental data, and presents – on a semiquantitative scale – convincing statements, consistent with chemical intuition. It is also a pleading for ligand field theory, which rationalises d-d spectra in terms of chemical bonding; though the latter spectra provide frequently only rather coarse information, their assistance in the energy analysis is crucial.     

Electrical properties of a novel fluorinated polycarbonate

The relative permittivity, loss and dielectric strength have been measured for a polycarbonate-based material, tetraaryl bisphenol A polycarbonate, that has been fluorine substituted (DiF p-TABPA-PC). The new material has a glass transition temperature, T_g = 489 K, that is higher than that for either conventional bisphenol A polycarbonate (BPA-PC) for which T_g = 421 K or for a copolymer of tetraaryl bisphenol A (TABPA) and bisphenol A (BPA) (TABPA-BPA-PC) for which T_g = 464 K. In addition, the dielectric strength of DiF p-TABPA-PC is almost identical to that for purified BPA-PC and slightly larger than the value for TABPA-BPA-PC. The relative permittivity and loss measurements were carried out from 10 to 10⁵ Hz over a wide temperature range and at pressures up to 0.25 GPa. Variable temperature results for the α relaxation and both temperature and pressure results for the γ relaxation regions are reported. The α relaxation exhibits standard behavior. The γ relaxation exhibits unusual characteristics such as a strong increase in peak height as temperature increases and a strong decrease in peak height with increasing pressure. The data for the γ relaxation have been analyzed using several formulations. Expressions for the peak height and peak position based on a two state (inequivalent well) model and the resulting parameters are discussed in terms of the insight they provide into the molecular mechanisms responsible for the sub-T_g relaxation. Ab initio SCF results for a related model compound are presented. Finally, the real part of the relative permittivity for the new polymer is about 10% higher than for BPA-PC.     

Thermodynamic study of aqueous sodium and potassium chloride and chromate systems at the temperature 298.15 K

The solubilities of ( m₁NaCl  + m₂Na₂ CrO ₄)(aq) and ( m₁KCl  + m₂ K ₂CrO ₄)(aq) where m denotes molality have been investigated at the temperature T =  298.15 K by the physico-chemical analysis method. Only the crystallization of the simple salts NaCl, Na ₂CrO ₄·4H ₂O, KCl, and K ₂CrO ₄have been established. The ternary solutions have been simulated thermodynamically at T =  298.15 K using the Pitzer model. The necessary thermodynamic parameters (binary and ternary ion-interaction parameters, thermodynamic solubility products) have been calculated and the theoretical solubility isotherms plotted. A very good agreement is found between calculated and experimental solubility isotherms. The standard molar Gibbs energies of formationΔ_rG_m^o of solid phases crystallizing in the systems under consideration have been estimated from theory.     

(Solid + liquid) isothermal evaporation phase equilibria in the aqueous ternary system (Li2SO4 + MgSO4 + H2O) at T = 308.15 K

The solubility and the density in the aqueous ternary system (Li₂SO₄ + MgSO₄ + H₂O) at T = 308.15 K were determined by the isothermal evaporation. Our experimental results permitted the construction of the phase diagram and the plot of density against composition. It was found that there is one eutectic point for (Li₂SO₄ · H₂O + MgSO₄ · 7H₂O), two univariant curves, and two crystallization regions corresponding to lithium sulphate monohydrate (Li₂SO₄ · H₂O) and epsomite (MgSO₄ · 7H₂O). The system belongs to a simple co-saturated type, and neither double salts nor solid solution was found. Based on the Pitzer ion-interaction model and its extended HW models of aqueous electrolyte solution, the solubility of the ternary system at T = 308.15 K has been calculated. The predicted solubility agrees well with the experimental values.     

Preparation and thermal properties of lanthanide complexes with 2,3-dichlorobenzoic acid and 1,10-phenanthroline

Three lanthanide complexes with a general formula [Ln(2,3-DClBA)₃phen]₂ (Ln(III) = Eu(1), Tb(2), Ho(3); 2,3-DClBA = 2,3-dichlorobenzoate; phen = 1,10-phenanthroline) were synthesized and characterized by elemental analysis, molar conductance, infrared and ultraviolet spectra and powder X-ray diffraction (XRD). The luminescent properties of the complexes 1 and 2 were studied. The thermal behaviors of the complexes were also discussed by thermogravimetric (TG), differential thermogravimetric (DTG) and infrared spectra (IR) techniques. The heat capacities of the complexes were measured from 259.15 to 493.02 K by means of Differential scanning calorimeter (DSC). The dependence of heat capacity on the reduce temperature x (x = [T ? (T_max + T_min)/2]/[(T_max ? T_min)/2]) was fitted to a polynomial equation with the least squares method for each complex. Furthermore, based on the fitted polynomial, the smoothed heat capacities and the derived thermodynamic functions (H_T ? H_298.15 K), (S_T ? S_298.15 K) and (G_T ? G_298.15 K) in the measured temperature range were obtained with an interval of 10 K.     

The standard molar enthalpy of sublimation ofη5-bis-pentamethylcyclopentadienyl iron measured with an electrically calibrated vacuum-drop sublimation microcalorimetric apparatus

A heat-flow Calvet microcalorimeter was adapted for the measurement of sublimation enthalpies by the vacuum-drop method, with samples of masses in the range 1 mg to 5 mg. The electrically calibrated apparatus was tested by determining the enthalpies of sublimation of benzoic acid and ferrocene, at T =  298.15 K. The obtained results, Δ_cr^gH_m^o(C₇H₆O₂)  =  (88.3  ±  0.5)kJ · mol ^− 1and Δ_cr^gH_m^o(C₁₀H₁₀Fe) =  (73.3  ±  0.1)kJ · mol ^− 1, are in excellent agreement with the corresponding values recommended in the literature. Subsequent application of the apparatus to the determination of the enthalpy of sublimation of η⁵-bis-pentamethylcyclopentadyenyl iron, at T =  298.15 K, led to Δ_cr^gH_m^o(C₂₀H₃₀Fe)  =  (96.8  ±  0.6)kJ · mol ^− 1.