Sequential injection lab-on-valve simultaneous spectrophotometric determination of trace amounts of copper and iron

A sequential injection (SI) method in a lab-on-valve (LOV) format for simultaneous spectrophotometric determination of copper and iron has been devised. The detection chemistry is based on the complex formation of 2-(5-bromo-2-pyridylazo)-5-[N-n-propyl-N-(3-sulfopropyl)amino]aniline (5-Br-PSAA) with copper(II) and/or iron(II) at pH 4.6. Copper(II) reacts with 5-Br-PSAA to form the complex which has an absorption maximum at 580 nm but iron(III) does not react. In the presence of a reducing agent only iron(II)-5-Br-PSAA complex is formed and detected at 558 nm. Under the optimum experimental conditions, the determinable ranges are 0.1-2 mg l⁻¹ for copper and 0.1-5 mg l⁻¹ for iron, respectively, with a sampling rate of 18 h⁻¹. The limits of detection are 50 μg l⁻¹ for copper and 25 μg l⁻¹ for iron. The relative standard deviations (n = 15) are 2% for 0.5 mg l⁻¹ copper and 1.8% for 0.5 mg l⁻¹ iron when determined in standard solutions. The recoveries range between 96 and 105% when determining 0.25-2 mg l⁻¹ of copper and 0.2-5 mg l⁻¹ of iron in artificial mixtures at copper/iron ratios of 1:10 to 5:1. The proposed SI-LOV method is successfully applied to the simultaneous determination of copper and iron in multi-element standard solution and in industrial wastewater samples.     

Solid-phase extraction and spectrophotometric determination of trace amounts of copper in water samples

A simple method for rapid and selective extraction, preconcentration and determination of copper as it's neocuproine complex by using octadecylsilica membrane disks and spectrophotometry is presented. Extraction efficiency and the influence of flow rates of sample solution and eluent, pH, amount of neocuproine and hydroxylamine hydrochloride, type and least amount of eluent for elution of copper complex from disks, break through volume and limit of detection were evaluated. Also the effects of various cationic interferences on percent recovery of copper were studied. Extraction efficiencies >99% were obtained by elution of the disks with minimal amount of solvent. The limit of detection of the proposed method is 0.12 ppb. The method was applied to the recovery and determination of copper in different water samples.     

Sequential spectrophotometric determination of trace amounts of periodate and iodate in water samples after micelle-mediated extraction

A cloud point extraction process using the nonionic surfactant Triton X-114 for extraction and preconcentration of periodate and iodate ions from aqueous solution was investigated. The method is based on the extraction of triiodide ion, the colored product of the reaction of periodate and iodate with iodide in acidic media. The triiodide was concentrated in surfactant rich phase and then determined spectrophotometrically at 358 nm. For the determination of periodate and iodate in mixture, two sets of conditions were established. In one set of conditions only periodate reacted with iodide but in the other set both ions reacted with iodide. The data were evaluated by the method of proportional equations. The optimal extraction and reaction conditions (e.g., surfactant and reagent concentrations and centrifuge time) were studied and the analytical characteristics of the method (e.g., limit of detection, linear range, preconcentration factor, and enhancement factors) were obtained. Under the optimized conditions, the methods allowed the determination of periodate and iodate at concentrations between 2.0 and 1000 and 4.0 and 400 ng/mL, respectively. The proposed method was successfully applied to the determination of periodate and iodate in water samples.     

Solid-phase extraction, separation, and visible spectrophotometric determination of trace amounts of iron in water samples.

A simple and reliable method is presented for the rapid extraction, separation, preconcentration, and determination of iron as its bathophenanthroline complex by the use of octadecylsilica membrane disks and spectrophotometry. We evaluted extraction efficiency, the influence of sample matrix, type and optimum amount of extractant, flow rates of sample solution and eluent, pH, amounts of bathophenanthroline and hydroxylamine hydrochloride, breakthrough volume, and limit of detection. We also studied the effects of various cationic interferences on percent recovery of iron. Complete elution of the complex from disks was obtained with a minimal amount of solvent. The limit of detection of the proposed method is 0.080 ppb. The method was applied to the recovery and determination of iron in natural waters.     

Determination of total and dissolved amount of iron in water samples using catalytic spectrophotometric flow injection analysis

A flow injection spectrophotometric method has been developed for the determination of dissolved and total amounts of iron in tap and natural water samples. The method for the determination of iron employs a sample acidification step in order to decompose iron hydroxide and iron-complexes into free iron, Fe(III) and Fe(II). The amounts of free iron were detected using a catalytic action of Fe(III) and Fe(II) on the oxidation of N,N-dimethyl-p-phenylenediamine in the presence of hydrogen peroxide. Increase in absorbance of oxidized product was detected spectrophotometrically at 514 nm. The proposed method allows 0.02 and 0.06 μg l⁻¹ of LOD and LOQ, respectively, with relative standard deviation (RSD) below 2%. The accuracy and the precision of the method were evaluated by the analysis of the standard reference material, river water. The developed method was successfully applied to real water samples.     

Sequential flow injection determination of iodate and periodate with spectrophotometric detection

A flow injection (FI) system is described for the sequential determination of periodate and iodate based on their reaction with iodide at pH 3.5. Two sample plugs were injected into the same carrier stream sequentially. One injection is for the iodate determination and the other for the sum of iodate and periodate determination. For iodate determination, molybdate solution buffered at pH of 3.5 was used for selective masking of periodate. The influences of reagent concentrations were studied by a univariable method and the influence of FI manifolds was studied using univariable and simplex method. Periodate and iodate can be determined in the range of 0.050-5.0 and 0.050-10 microg/ml, respectively. The 3 sigma limit of detection was 0.030 and 0.050 microg/ml for periodate and iodate, respectively. The proposed method has been applied for the sequential determinations of periodate and iodate in water samples.     

Field determination of trace iron in fresh water samples by visual and spectrophotometric methods.

Sensitive visual and micro spectrophotometric methods have been developed for field determination of trace iron in fresh water samples. For the visual method, a water sample (0.45-microm filtrate acidified to 0.1 M HCl) was placed in a glass vial and mixed with a reagent solution containing 1,10-phenanthroline, sodium thiocyanate and 0.1 M HCl. Iron was extracted as pink ferroin thiocyanate with 1 ml of 4-methy-2-pentanone. The sample up to 20 ml was added step-by-step, until the color of the extract was detected visually. Without any special instrument or color standard, iron down to 0.001 mg 1(-1) (0.025 microg) in a sample can be determined with an error of 20% in the field. For the micro spectrophotometric method, the extract for 20 ml of sample was separated by capillary suction in a column (micro pipette chip) with acrylic fibers. A part of the extract was pushed out into a micro cell for the absorbance measurement at 525 nm. The column was re-usable after washing with ethanol. This method had a detection limit of 0.001 mg 1(-1) and allowed determinations within an error of 5%. The proposed methods were applied to deionized-, tap-, river-, lake- and reservoir-water samples.     

顺序注射阻抑动力学光度法测定环境水样中的间苯二酚

在酸性条件下,利用间苯二酚能抑制罗丹明B和溴酸根反应速率的原理,联用顺序注射技术建立了非平衡态快速测定痕量间苯二酚的新方法.优化了顺序注射流路参数、试剂用量,考察了共存物的影响.在最佳条件下,该法测定间苯二酚的线性范围为0.20～3.00 μg/mL,检出限为0.09 μg/mL,每小时可测定40个样.     

Multisyringe flow injection spectrophotometric determination of uranium in water samples

A multisyringe flow injection analysis method for the determination of uranium in water samples was developed. The methodology was based on the complexation reaction of uranium with arsenazo (III) at pH 2.0. Uranium concentrations were spectrophotometrically detected at 649 nm using a light emitting diode. Under the optimized conditions, a linear dynamic range from 0.1 to 4.0 μg mL⁻¹, a 3σ detection limit of 0.04 μg mL⁻¹, and a 10σ quantification limit of 0.10 μg mL⁻¹ were obtained. The reproducibility (%) at 0.5, 2.5, and 4.0 μg mL⁻¹ was 2.5, 0.9, and 0.6%, respectively (n = 10). The interference effect of some ions was tested. The proposed method was successfully applied to the determination of uranium in water samples.     

Ultra-trace analysis of nitrite in food samples by flow injection with spectrophotometric detection

A flow injection system with spectrophotometric detection is proposed for the determination of low levels of nitrite based on its catalytic effect on the oxidation of gallocyanine by bromate in acidic media. Various analytical parameters such as acidity, reagent concentration, flow rate, sample size, time, temperature, and interfering species were studied. The calibration graph was linear for 0.020–0.500 μg/mL of nitrite. The method is successfully applied to food samples. Up to 30 ± 5 samples can be analyzed per hour. Received: 8 April 1998 / Revised: 3 June 1998 / Accepted: 31 July 1998     

Ultra-trace analysis of nitrite in food samples by flow injection with spectrophotometric detection

A flow injection system with spectrophotometric detection is proposed for the determination of low levels of nitrite based on its catalytic effect on the oxidation of gallocyanine by bromate in acidic media. Various analytical parameters such as acidity, reagent concentration, flow rate, sample size, time, temperature, and interfering species were studied. The calibration graph was linear for 0.020–0.500 μg/mL of nitrite. The method is successfully applied to food samples. Up to 30 ± 5 samples can be analyzed per hour. Received: 8 April 1998 / Revised: 3 June 1998 / Accepted: 31 July 1998     

Flow injection spectrophotometric determination of trace amounts of selenium

A simple, rapid and sensitive flow injection spectrophotometric method for determination of selenium (0.005-1.5 mug ml(-1)) is described. The method is based on the catalytic effect of Se(IV) on the reduction reaction of thionine (TN) with sulphide ion, monitored spectrophotometrically at 598 nm. The detection limit is 5 ng ml(-1) the relative standard deviation for eight replicate measurements is 1.1% for 1 mug ml(-1) of selenium. The sampling rate is 25-30 samples h(-1). The procedure was applied successfully to the determination of selenium in real samples.     

双波长双指示剂催化光度法测定铜的研究

研究了在pH 4.0的HAc～NaAc缓冲介质中,利用痕量铜(Ⅱ)催化过氧化氢氧化罗丹明B和亚甲基蓝褪色的指示反应,通过测量540 nm和660 nm下,催化体系和非催化体系吸光度的变化,建立了双波长双指示剂催化动力学光度法测定痕量铜的新方法.方法的线性范围为0.00080～0.048μg/mL,检出限为4.0×10~(-11) g/mL.方法可用于水中铜的测定.     

Extraction-liquid chromatography with electrochemical and spectrophotometric detection for the determination of copper and iron in biological and river water samples

Reversed-phase liquid chromatography using cupferron as a precolumn derivatizing agent was developed for the determination of Cu(II) and Fe(III) in biological materials and natural water samples. In the direct method, the metal cupferronates formed in acetonitrile-water (1 + 1) are injected onto an ODS column followed by separation with a mobile phase containing acetonitrile-acetate buffer (pH 3.5) (7 + 3) and other reagents. Amperometric detection with a glassy carbon electrode at ?0.40 V vs. Ag/AgCl can be used to determine both metals simultaneously. The electrochemical detection method has better sensitivity for the determination of Fe(III) than the usual spectrophotometric detection at 375 nm. If a large volume of aqueous sample is available, concentration of the two metal ions can be made by extraction with ethyl acetate prior to the chromatographic determination. In this case, liquid chromatographic separation and determination can be performed with the ODS column using a mobile phase consisting of acetonitrile-methanol-ethyl acetate-0.02 M acetate buffer (pH 3.5) (45 + 20 + 5 + 30).     

Flow injection catalytic determination of ruthenium with spectrophotometric detection

A new flow injection catalytic method was described for the determination of ruthenium(III) based on its catalytic effect on the oxidation of brilliant cresyl blue (BCB) by periodate in acidic media. The reaction was followed spectrophotometrically by measuring the absorbance of the dye at 635 nm. Under optimum conditions, ruthenium can be determined in the range of 1.0-100.0 ng ml(-1) with a relative standard deviation of 1.1% and with a limit of detection of 0.70 ng ml(-1). The influence of reagent and manifold variables were studied and optimized. The method was tested for the determination of ruthenium(III) in some synthetic mixtures.     

Sequential injection spectrophotometric determination of trace amounts of iodide by its catalytic effect on the 4,4'-methylenebis(N,N-dimethylaniline)-chloramine-T reaction

A simple and sensitive sequential injection spectrophotometric procedure is proposed for the determination of trace amounts of iodide in pharmaceutical preparations. The method is based on the catalytic effect of iodide on the (tetra base) 4,4′-methylenebis(N,N-dimethylaniline)-chloramine-T reaction in acidic solution. The method involves a sequential aspiration of 255 μl sample/standard followed by 170 μl tetra base and then 128 μl chloramine-T solutions into a carrier stream to be stacked inside a holding coil and flow reversed through a reaction coil towards a detector. The resulting colored compound is measured at 600 nm using an UV/Vis-spectrophotometer. All the parameters that affect the reaction were evaluated and the calibration curve is linear over a range of 0.1–6.0 μg l⁻¹ of iodide concentration with detection limit of 0.05 μg l⁻¹. A sample throughput of 80 samples per hour and relative standard deviation of less than 2.0% was achieved. The method is successfully applied for the determination of iodide in three different samples (tablets).     

Sequential determination of iron(II) and iron(III) in pharmaceutical by flow-injection analysis with spectrophotometric detection.

A flow injection procedure for the sequential spectrophotometric determination of iron(II) and iron(III) in pharmaceutical products is described. The method is based on the catalytic effect of iron(II) on the oxidation of iodide by bromate at pH = 4.0. The reaction was monitored spectrophotometrically by measuring the absorbance of produced triiodide ion at 352 nm. The activating effect for the catalysis of iron(II) was extremely exhibited in the presence of oxalate ions, while oxalate acted as a masking agent for iron(III). The iron(III) in a sample solution could be determined by passing through a Cd-Hg reductor column introduced in the FIA system to reduce iron(III) to iron(II), which allows total iron determination. Under the optimum conditions, iron(II) and iron(III) could be determined over the range of 0.05 - 5.0 and 0.10 - 5.0 microg ml(-1), respectively with a sampling rate of 17 +/- 5 h(-1). The experimental limits of detection were 0.03 and 0.04 microg ml(-1) for iron(II) and iron(III), respectively. The proposed method was successfully applied to the speciation of iron in pharmaceutical products.     

Development of novel detection reagent for simple and sensitive determination of trace amounts of formaldehyde and its application to flow injection spectrophotometric analysis

In this paper, a novel detection reagent for formaldehyde determination is proposed, and is applied to a simple and highly sensitive flow injection method for the spectrophotometric determination of formaldehyde. The method is based on the reaction of formaldehyde with methyl acetoacetate in the presence of ammonia. The increase in the absorbance of the reaction product was measured at 375 nm. An inexpensive light emitting diode (LED)-based UV detector (375 nm) was, for the first time, used. Under the optimized experimental conditions, formaldehyde in an aqueous solution was determined over the concentration range from 0.25 to 20.0 × 10⁻⁶ M with a liner calibration graph; the limit of detection (LOD) of 5 × 10⁻⁸ M (1.5 μg L⁻¹) was possible. The relative standard deviation of 12 replicate measurements of 5 × 10⁻⁶ M formaldehyde was 1.2%. Maximum sampling throughput was about 21 samples/h. The effect of potential interferences such as metals, organic compounds and other aldehyde was also examined. The analytical performance for formaldehyde determination was compared with those obtained by the conventional acetylacetone method, which uses visible absorption spectrophotometry. Finally, the proposed method was successfully applied to the determination of formaldehyde in natural water samples.     

Flow injection spectrophotometric determination of ultra trace amounts of oxalic acid

A new simple, sensitive and rapid catalytic-spectrophotometric method for the determination of oxalic acid has been described based on its catalytic effect on the redox reaction between dichromate and Brilliant cresyl blue in acidic media by means of a flow injection analysis method. The color change of Brilliant cresyl blue due to its oxidation was monitored spectrophotometrically at 625 nm. The calibration graph was linear in the range of 0.020-4.70 microg/mL oxalic acid with a limit of detection 0.005 microg/mL of oxalic acid. The relative standard deviation for ten replicate measurements of 0.020 microg/mL and 0.900 microg/mL was 2.2% and 1.7%, respectively. No serious interference was identified. Oxalic acid was determined in wastewater and in spinach by the proposed method with satisfactory results.     

Dapsone and iminodibenzyl as novel reagents for the spectrophotometric determination of trace amounts of nitrite in water samples.

A rapid, simple, sensitive and selective spectrophotometric determination of nitrite using new diazotizing and coupling reagents is described. The method is based on a diazotization-coupling reaction between dapsone and iminodibenzyl in a hydrochloric acid medium. The molar absorptivity and Sandell's sensitivity were found to be 7.5 x 10(4) l mol(-1) cm(-1) and 0.000613 microg ml(-1), respectively. The interference effects of various cations and anions were also studied and reported. This method has been found to be applicable for the determination of nitrite in various water samples.