Range of turbulence-negligible propagation of Gaussian Schell-model array beams

For linear Gaussian Schell-model (GSM) array beams, the range of turbulence-negligible propagation, in which all of the spatial and angular spreading and the beam propagation factor increasing due to turbulence can be neglected, has been investigated in detail. It is shown that this range of GSM array beams increases with decreasing turbulent parameter and coherent parameter, and depends on the beam number, the waist width, and the relative beam separation distance. This range of a GSM array beam is larger than that of a coherent Gaussian array beam, and this range of a GSM array beam with a large relative beam separation distance is larger than that of a single GSM beam, implying that a GSM array beam may be more appropriate to be used in atmospheric optical communication links than a coherent Gaussian array beam or a GSM beam.     

平顶飞秒激光经圆锥透镜在熔融石英中成丝及超连续辐射

实验研究了平顶飞秒激光经圆锥透镜后在熔融石英中的成丝及超连续辐射.与高斯飞秒激光的成丝对比发现,平顶飞秒激光可以获得在圆锥透镜焦深区域内强度分布更为均匀的等离子体细丝,这一特征更有利于飞秒激光在固体介质中进行微纳加工等领域的应用.并且,在不损伤熔融石英的条件下,平顶飞秒激光成丝可以获得更高能量、更高转换效率的超连续辐射,这是因为若产生光强相近的细丝,平顶飞秒激光所需的初始激光能量更高,此激光能量下产生的细丝长度更长、均匀性更好.     

Scintillation properties of dark hollow beams in a weak turbulent atmosphere

The on-axis scintillation index for a circular dark hollow beam (DHB) propagating in a weak turbulent atmosphere is formulated, and the scintillation properties of a DHB are investigated in detail. The scintillation index for a DHB reduces to the scintillation index for a Gaussian beam, an annular beam and a flat-topped beam under certain conditions. It is found that the scintillation index of a DHB is closely related to the beam parameters and can be lower than that of a Gaussian beam, an annular beam and a flat-topped beam in a weak turbulent atmosphere at smaller waist sizes and longer propagation lengths. PACS 42.25.Bs; 42.68.Ay     

强流重离子束在轴对称电场中的温度和能量展宽

本文研究带电粒子束在轴对称电场(包含束空间电荷平均场)中的温度和能量展宽,所得结果表明,在漂移区内,此种能量展宽与束电流成正比,与束的宏观流动速度成反比,因此,对于强流重离子束而言,此种能量展宽在总的能量展宽中将起重要的作用,若束能为20keV,束流为20mA,在漂移区中,¹H离子束的能量展宽为26.5eV,而相同条件下的¹²¹Sb离子束则为291.5eV,而且随束流增加线性上升,本文对束温度的研究结果表明,在漂移区中,束空间电荷效应使束温度增加。 关键词：     

椭圆涡旋光束在海洋湍流中的传输特性

本文采用分步相位屏方法来仿真椭圆涡旋光束在海洋中的实际传输情况,并对椭圆涡旋光束在海洋湍流中的传输光强和闪烁因子进行了仿真。研究发现,椭圆涡旋光束在海洋传输过程中,光斑会发生明显的旋转,同时光斑会产生暗核且暗核个数与光束的拓扑荷数相等。一个拓扑荷数为m的相位奇点会分裂成m个拓扑荷数为1的相位奇点,并且海洋湍流越强,光斑受到的干扰越严重。研究还发现,在较弱的海洋湍流中,随着传输距离的增加,椭圆涡旋光束的闪烁因子会低于高斯光束和涡旋光束的闪烁因子,而且在远距离处拓扑荷数越大闪烁因子降低越明显,同时也发现,传播一段距离后涡旋光束的闪烁因子会低于高斯光束的闪烁因子。在较强湍流中,椭圆涡旋光束的闪烁因子会交叠在一起。对于不同强度的海洋湍流,随着均方温度耗散率的增大,椭圆涡旋光束的轴上点闪烁因子也增大。在同一传输距离处,束腰宽度越小的椭圆涡旋光束闪烁因子越小。     

Average spreading of a linear Gaussian–Schell model beam array in non-Kolmogorov turbulence

The average spreading of a linear Gaussian–Schell model (GSM) beam array in non-Kolmogorov turbulence is studied, where the coherent combination is considered. The effects of the beam number, the separation distance between two adjacent beams and the generalized exponent on the root-mean-square (rms) beam width are investigated. The results indicate that the rms beam width in non-Kolmogorov turbulence is different from that in Kolmogorov turbulence, and there is an optimum beam number that leads to a minimum beam width. Further, the beam width can reach the minimum value by adopting the optimum separation distance, which decreases with the increase of beam number. Besides, the partially coherent beam array is less sensitive to the atmospheric turbulence than the fully coherent one.     

Beam quality factor for coherently combined fiber laser beams

The beam quality factor for a coherently combined beam is studied in detail. A theoretical analysis and a numerical calculation are given to illustrate that the M² factor is not a proper means for evaluating the beam quality of a coherently combined beam. The beam propagation factor is introduced to evaluate the beam quality. The effect of phase error on the beam quality is also studied. Results indicate that the beam quality of a coherently combined beam depends mainly on the fill factor of the laser array and not on the number of lasers. It is also revealed that the allowed phase error does not change with the number of lasers in order to ensure the energy encircled in a certain bucket.     

Self-aligned fiber-based dual-beam source for STED nanolithography

A fiber-based source that can be exploited in a stimulated emission depletion(STED) inspired nanolithography setup is presented. Such a source maintains the excitation beam pulse, generates a ring-shaped depletion beam, and automatically realizes dual-beam coaxial alignment that is critical for two beam nanolithography. The mode conversion of the depletion beam is realized by using a customized vortex fiber, which converts the Gaussian beam into a donut-shaped azimuthally polarized beam. The pulse width and repetition frequency of the excitation beam remain unchanged, and its polarization states can be controlled. According to the simulated point spread function of each beam in the focal region, the full width at half-maximum of the effective spot size in STED nanofabrication could decrease to less than 28.6 nm.     

Beam induced vacuum measurement error in BEPC II

When the beam in BEPCII storage ring aborts suddenly, the measured pressure of cold cathode gauges and ion pumps will drop suddenly and decrease to the base pressure gradually. This shows that there is a beam induced positive error in the pressure measurement during beam operation. The error is the difference between measured and real pressures. Right after the beam aborts, the error will disappear immediately and the measured pressure will then be equal to real pressure. For one gauge, we can fit a non-linear pressure-time curve with its measured pressure data 20 seconds after a sudden beam abortion. From this negative exponential decay pumping-down curve, real pressure at the time when the beam starts aborting is extrapolated. With the data of several sudden beam abortions we have got the errors of that gauge in different beam currents and found that the error is directly proportional to the beam current, as expected. And a linear data-fitting gives the proportion coefficient of the equation, which we derived to evaluate the real pressure all the time when the beam with varied currents is on.     

Instantaneous electron beam emittance measurement system based on the optical transition radiation principle

One kind of instantaneous electron beam emittance measurement system based on the optical transition radiation principle and double imaging optical method has been set up. It is mainly adopted in the test for the intense electron-beam produced by a linear induction accelerator. The system features two characteristics. The first one concerns the system synchronization signal triggered by the following edge of the main output waveform from a Blumlein switch. The synchronous precision of about 1 ns between the electron beam and the image capture time can be reached in this way so that the electron beam emittance at the desired time point can be obtained. The other advantage of the system is the ability to obtain the beam spot and beam divergence in one measurement so that the calculated result is the true beam emittance at that time, which can explain the electron beam condition. It provides to be a powerful beam diagnostic method for a 2.5 kA, 18.5 MeV, 90 ns (FWHM) electron beam pulse produced by Dragon I. The ability of the instantaneous measurement is about 3 ns and it can measure the beam emittance at any time point during one beam pulse. A series of beam emittances have been obtained for Dragon I. The typical beam spot is 9.0 mm (FWHM) in diameter and the corresponding beam divergence is about 10.5 mrad.     

非理想氢原子束真空环境长程传输模拟研究

模拟研究了非理想氢原子束在真空环境下的长程传输效应。根据中性化程度的不同,将非理想束分为欠中性束和过中性束。通过建立束流传输的准电磁模型,研究了束流密度、中性化因子、空间磁场和弹性散射等因素对非理想氢原子束的影响。结果表明:对于欠中性束,负氢离子的存在对氢原子的传输几乎没有影响,因此欠中性束的发射装置可以考虑去除偏置磁场,以减小设备体积和质量;对于过中性束,束流损失率与束流密度和中性化因子有关,即束流密度越大,束流损失越大;中性化因子越高,束流损失就越高;而无论是欠中性束还是过中性束,空间磁场和粒子间的弹性散射对其传输都没有影响。     

三维自散焦介质中的暗光束诱导亮光束聚焦

为了获得一种对称压缩圆光束的方法,系统研究了三维自散焦介质中亮暗光束对的共同传输。数值结果表明:当两光束中心重合时,若抽运光(暗光束)初始振幅远大于信号光(亮光束)初始振幅,抽运光将通过交叉相位调制(XPM)诱导信号光聚焦,使得信号光的圆形光斑被对称压缩。讨论了光束参量对信号光聚焦效果的影响,发现抽运光初始振幅越大,信号光聚焦越强。当抽运光初始振幅一定时,暗光束的初始束宽存在最佳值使得信号光压缩最强。当抽运光与信号光的波长比取值为0.5~1.5时,信号光聚焦程度随着波长比的增大而有所降低。还设计了验证理论结果的实验方案。     

Stimulated Brillouin scattering of elliptical laser beam in collisionless plasma

This paper presents an investigation of self-focusing of elliptical laser beam in collisionless plasma and its effect on stimulated Brillouin scattering. The pump beam interacts with a pre-excited ion-acoustic wave leading to Brillouin back-scattered process. The transverse intensity gradient of a pump beam generates a ponderomotive force, which modifies the background plasma density profile in a direction transverse to pump beam axis. This modification in density effects the incident laser beam, ion-acoustic wave and back-scattered beam. Non-linear differential equations for the beam width parameters of pump laser beam, ion-acoustic wave and back-scattered beam are set up and solved numerically. It is observed from the analysis that the focusing of waves enhances the SBS back-reflectivity.     

Thermal effects of a laser beam tube consisting of a window and nonflowing gas

High-energy laser systems include an optical train and a gas medium that must be capable of transporting and directing the beam. The optical train is termed a laser beam tube. Because of the finite absorption of laser energy, the thermal effects of the beam tube make the beam diffuse and cause degradation of the laser beam's quality. We study systematically a beam tube consisting of a laser window made from white bijou (i.e., Al2O3) or fused silica and a tube of nonflowing nitrogen or helium gas. The results show that the thermal effects of the window and the gas on the beam neutralize each other; in particular, in some cases they compensate for each other completely, such that the beam tube has no effect on the beam quality in spite of the fact that separately each has a severe effect. We explain how to acquire the specific cases.     

神龙一号电子束质心运动测量研究

 在强流直线感应加速器中,电子束质心位置的控制是一项重要技术,要达到较好的控制效果,前提是对电子束质心位置进行准确的测量和定位。针对具有时间分辨的电子束质心位置的测量和确定,介绍了测量实验系统的建立和数据处理两个方面的研究工作。该处理方法在实际应用时能够将电子束质心位置的误差控制在1～2个像素内。用高速分幅相机以10 ns的时间间隔、3 ns的曝光时间获得了神龙一号加速器在漂移段出口处的电子束质心运动情况。结果表明：束的质心主要在半径为0.5 mm的区域内运动,束斑直径dFWHM值分别为8.4,8.8,8.5,9.3和7.6 mm,测量结果可以为束的调控提供准确参数。     

无衍射光束聚焦后的重建与矫正

基于衍射理论分析了无衍射光束聚焦后重建现象.导出重建后的光场分布表达式,数值模拟了重建光束的光强分布.结果表明,重建光束中心光斑较聚焦前的无衍射光束中心光斑大,而且重建后的光束有较大的发散角,光束随着传输很快扩散,光强迅速衰减.此类光束的应用受到限制.利用另一正透镜对重建后的光束加以矫正.并且由几何光学知识,得到了改变重建光束参量的方法,研究结果拓宽了无衍射光束的应用.用体视显微镜和CCD照相机组成的系统拍摄光束强度分布,实验结果与理论计算相吻合.     

The effect of laser beam size in a zig-zag collimator on transverse cooling of a krypton atomic beam

The effect of size of a cooling laser beam in a zig-zag atomic beam collimator on transverse cooling of a krypton atomic beam is investigated. The simulation results show that discreteness in the interaction between the cooling laser beam and atomic beam, arising due to finite size and incidence angle of the cooling laser beam, significantly reduces the value of transverse velocity capture range of the collimator. The experimental observations show the trend similar to that obtained from simulations. Our study can be particularly useful where a small zig-zag collimator is required.     

带电粒子束传输中横向发散的类ABCD定律

 傍轴近似下带电粒子束传输可完全类比于近轴光线椭圆高斯光束的传输。基于这种类比，建立了带电粒子束传输中横向发散的复曲率半径的类ABCD定律，引入了带电粒子在横向的复曲率半径的概念，并以复曲率半径的实部表征带电粒子束的敛散特性，虚部表征带电粒子束的束斑大小。由此提出：带电粒子束整体可被看作类椭圆高斯光束，其发射度与光束波长的作用相同。通过这种类比可知，在适宜的加速器环境下，理论上可能产生相干带电粒子束。     

基于紧聚焦方式的阵列光束相干合成特性分析

为获得高功率、波长量级尺寸的聚焦光斑,提出利用紧聚焦方式实现阵列光束相干合成的新方案.通过建立阵列光束经紧聚焦方式相干合成的物理模型,分析了阵列光束的排布方式、偏振态、束宽、间距和紧聚焦系统数值孔径等参数对合成光束特性的影响及规律.结果表明,阵列光束经紧聚焦方式合束时,线偏振及圆偏振阵列光束均能获得较好的合成效果,径向偏振阵列光束次之,而角向偏振阵列光束则不能有效地合成.通过优化阵列光束的排布方式、束宽和间距,以及合理选择紧聚焦系统的数值孔径,能在保持较好光束质量和较高合成效率的前提下获得能量集中度高的焦斑.     

基于高次谐波产生的极紫外偏振涡旋光

突破传统涡旋光场束缚,发展短波极紫外涡旋光场是实现阿秒脉冲偏振控制的有效途径.本研究利用自制的平场光栅光谱仪和超快时间保持的单色仪,以800 nm,35 fs高斯或具有偏振奇点的涡旋光脉冲驱动诱导氩原子产生高次谐波,分别获得相应的高次谐波光谱以及谐波谱单阶光源的分布.实验结果表明,基于高次谐波产生实现近红外波段的涡旋光束特性转移到极紫外波段,优化后的极紫外涡旋可以实现每秒108光子数输出.同时发现极紫外波段的涡旋场和高斯场高次谐波产生具有相似相位匹配机制.基于高次谐波产生的极紫外波段的偏振涡旋光为探究和操控原子分子量子态的含时演化动力学以及形成阿秒矢量光束提供了重要的方法和技术手段.