Metal vapor densities and excitation temperatures in a pseudosparkswitch

The densities of iron, tungsten, copper, and nickel vapors produced by pseudosparks in a switch-like configuration are measured by laser-induced fluorescence. The cathode is made of a composite material essentially consisting of tungsten, but also containing the other metals mentioned. Total vapor densities are calculated from ground state densities using the excitation temperature of iron, which decays from 1900 K at 9 μs after initiation of the discharge to 600 K about 150 μs later. With maximum copper and tungsten vapor densities of 1.5×10¹⁸ m^-3 and 2×10¹⁷ m ^-3, respectively, the composition of metal vapor differs considerably from that of the cathode material. Iron and nickel vapors are present with densities in the range of 10¹⁶ m^-3. By comparison of vapor density ratios with vapor pressure ratios it is found that regions with temperatures in excess of 5000 K exist on the cathode. These are attributable to emission sites providing the electrons for current conduction. The vapor densities are roughly proportional to the current amplitude, while the gas pressure has practically no influence between 15 and 30 Pa     

Spectroscopic investigation of a low current arc in pure fluorine

A pure fluorine 10-A DC arc has been operated in an Al₂O₃ tube of 18 mm diameter at atmospheric pressure. This arc was used to perform radially resolved spectroscopic end-on measurements in the visible and UV-spectral regions. An excitation temperature of 7800 K on the arc axis was determined from the intensity of atomic fluorine lines, and an ion density of 1.7×10 ²¹ m^-3 was determined from the half-width of the contamination line H_β. A Boltzmann plot of the affinity continuum in the UV-spectral region yields two groups of electrons. A group of hot electrons is characterized by a temperature that agrees with the excitation temperature, and a group of cold electrons has a temperature in accordance to the gas temperature of 4000 K. The absolute intensity of the affinity continuum gives and electron density of 1.3×10²⁰ m^-3 on the arc axis, which is lower than the density of both positive and negative ions in the discharge. From the difference between the electron and gas temperature, an elastic collision cross section between the electrons and F-atoms of 2×10^-20 m² is determined     

Measurement of the tungsten ion concentration after forcedextinction of a vacuum arc

The concentrations of singly ionized and neutral tungsten atoms were measured by laser-induced fluorescence after the forced extinction of vacuum arcs between tungsten-copper butt contacts, 28-mm in diam. and 10-mm apart. The 50-Hz current was forced to zero at its maximum of 200 A in 1.3 μs by application of a reverse voltage. Near current zero, the ion concentration of 4×10¹⁷ m^-3 is of the same order of magnitude as the atomic tungsten concentration, which is 6×10¹⁷ m^-3. While the concentration of the neutrals remains virtually constant during 20 μs after current zero, the ion concentration decays by three orders of magnitude in the same time. The decay-time constant varies from 1.9 μs close to the postarc cathode to 3.6 μs near the postarc anode. It is concluded that the dielectric recovery of vacuum gaps after diffuse arcs is mainly controlled by residual charge carriers     

A model for a uniform steady-state vacuum arc with a hot anode

A model is formulated and evaluated for a Uniform electrical discharge sustained in vapor evaporated from an arc-heated anode. The plasma potential is positive with respect to both the cathode and anode. For a Cu anode, the anodic vapor dominates the plasma for current densities exceeding 8 kA/m². The anode heating potential is approximately 6.5 V, and the dominant cooling mechanism is evaporation for current densities exceeding 20 kA/m². Over the range 10 to 10000 kA/m², the electron density increases from 8×10¹⁷ to 5×10²³ m^-3, while the ionization fraction rises from 0.3% to 4%. At the lower end of this current range the electrical resistivity of 4 mΩ-m is determined primarily by electron-neutral collisions, while with increasing current the resistivity decreases to 0.7 mΩ-m, with electron-ion collisions contributing an equal share. This hot-anode vacuum arc may have potential for industrial application as a macroparticle-free high-deposition-rate coating source     

Validity conditions for complete and partial local thermodynamicequilibrium of nonhydrogenic level systems and their application tocopper vapor arcs in vacuum

Validity conditions for complete and partial local thermodynamic equilibrium (CLTE and PLTE) of homogeneous, time-dependent, and optically thin plasmas are derived. For Cu I, electron densities of n_e⩾(5×10²²-5×10²³ ) m^-3 are required for the establishment of CLTE. For Cu I and Cu II, n_e⩾(5×10²¹-5×10²¹ -5×10²²) m^-3 is necessary for PLTE (for electron temperatures of 1-2 eV). Application to low-current copper vapor arcs in vacuum shows that CLTE can be expected for r<200-600 μm (r=distance from the cathode spot). A further limitation follows for temperatures of 2 eV or higher if diffusion effects are taken into consideration. Consequently, the use of the LTE formulas in plasma spectroscopy of low-current vacuum arcs is very limited     

Measurement of cathode spot parameters with pulsed laserdiagnostics

The cathode spot formation in air within the first 170 ns was investigated by laser absorption photography and ps-pulse interferometry. The discharge was initiated between electrodes made from Ag or Pd with cathode-anode distance below 300 μm, the arc duration was some milliseconds, and the arc current 5-10 A. Picosecond holographic interferometry and momentary absorption photography yielded spatial-temporal density distributions in the ignition phase of the cathode spot. An absolute electron density value on the order of 4×10²⁶ m^-3 has been found. In contrast to vacuum, the cathode spot plasmas broaden little with increasing distance from the cathode, thus narrow plasma channels are observed in the vicinity of the cathode surface having diameters <20 μm     

Investigation of arc roots of constricted high current vacuum arcs

The anodic and cathodic arc roots of constricted high current vacuum arcs were investigated with a fast framing charge-coupled device camera of 1 μs exposure time. The experiments were performed with cup-shaped contacts, with sinusoidal currents of amplitudes between 20 and 100 kA, and a sine halfwave duration of 10-12 ms. The arcs were drawn by contact separation and accelerated by the Lorentz force between the arc current and the transverse magnetic field generated by the contrate contact. The anode and cathode arc roots behave reproducibility and arc scaleable within the range of currents investigated. Both types of arc roots are elliptical, with a major to minor axis ratio of 1.4. The major axis points are in the direction of arc propagation. Anodic and cathodic arc root cross-sectional areas as a function of current can both be described by a potential law with a common exponent of 0.76. For currents of 20-100 kA, mean current densities of 81-121 and 41-60 kA/cm ² were found in anode and cathode arc roots, respectively. Estimations of their temperature and vapor densities were performed. For the investigated current range T_A≈3300-3600 K, n_A ≈1.6*10¹⁹-2.2*10¹⁹cm^-3 and T _C≈3200-3400 K, n_C≈0.8*10¹⁹-1.2*10 ¹⁹ cm^-3 were found for anode and cathode, respectively     

不同电场下碳纳米管场致发射电流密度研究

本文运用密度泛函理论和金属电子论, 深入研究了碳纳米管场致发射电流的变化规律. 结果显示其发射电流密度取决于体系的态密度、赝能隙、管长和局域电场, 在不同范围电场下的变化规律不同. 在较低电场下, 发射电流密度随电场增强而近似线性增大(对应的宏观电场须小于18 V· μm^-1); 但在较高电场下, 发射电流密度随外电场增加呈现非周期性振荡增长趋势, 碳纳米管表现为电离发射. 本文进一步研究了金属性碳纳米管电导率在不同电场下的变化规律.     

Neutral copper vapor density and electric recovery after forcedextinction of vacuum arcs

Dielectric recovery data were obtained for vacuum arcs between chromium copper butt contacts 30 mm in diameter and 2 mm apart. The 50-Hz arc current was forced to zero at its maximum of 200 A in about 1 μs. Following current zero, high-voltage pulses of a sufficient amplitude to always cause breakdown were applied to the gap. Gap recovery is characterized by the measured breakdown voltage as a function of time. Dielectric strength of the gap rises sharply within the first few microseconds after current zero, reaching its final value in about 10 μs. Neutral copper concentration in the center of the gap was measured by laser-induced fluorescence under conditions very similar to those of the recovery measurements. In contrast to the fast gap recovery, the copper vapor concentration does not change substantially during the first 100 μs from its value of 1.4×10¹⁸ m ^-3 near current zero. It is concluded that the neutral copper vapor concentration does not play a decisive role in gap recovery under these experimental conditions. This is corroborated by the fact that the mean free path for electron-impact ionization of copper atoms exceeds the gap length by four orders of magnitude     

HL-2Aװ��ECRH�����͹��ʳ�������

采用TORAY代码对HL-2A装置ECRH系统在单零点偏滤器位形下的波与等离子体相互作用的情况进行了模拟计算,研究了等离子体和波参数对ECRH波迹和功率沉积以及电流驱动的影响。根据数值计算结果,HL-2A装置ECRH系统在等离子体线平均密度为3.0×1013cm-3、中心电子温度为1.19keV的情况下,以O模作为入射波垂直入射时的单次吸收系数为99.3%,最大电流驱动效率为0.005×1020A.W-1.m-2。     

Performance of dual-band short-or mid-wavelength infrared photodetectors based on InGaAsSb bulk materials and InAs/GaSb superlattices

In this paper,we demonstrate bias-selectable dual-band short-or mid-wavelength infrared photodetectors based on In_(0.24)Ga_(0.76)As_(0.21)Sb_(0.79)bulk materials and InAs/GaSb type-II superlattices with cutoff wavelengths of 2.2μm and 3.6μm,respectively.At 200 K,the short-wave channel exhibits a peak quantum efficiency of 42%and a dark current density of5.93×10~(-5)A/cm~2at 500 mV,thereby providing a detectivity of 1.55×10~(11)cm·Hz~(1/2)/W.The mid-wave channel exhibits a peak quantum efficiency of 31%and a dark current density of 1.22×10~(-3)A/cm~2at-300 mV,thereby resulting in a detectivity of 2.71×10~(10)cm·Hz~(1/2)/W.Moreover,we discuss the band alignment and spectral cross-talk of the dual-band n-i-p-p-i-n structure.     

温稠密钛电导率计算

温稠密物质是惯性约束核聚变、重离子聚变、Z箍缩动作过程中物质发展和存在的重要阶段. 其热力学性质和辐射输运参数在聚变实验和内爆驱动力学模拟过程中有至关重要的作用. 本文通过建立非理想Saha方程, 结合线性混合规则的理论方法模拟了温稠密钛从10^-5-10 g·cm^-3, 10⁴ K到3×10⁴ K区间的粒子组分分布和电导率随温度密度的变化, 其中粒子组分分布由非理想Saha方程求解得到. 线性混合规则模型计算温稠密钛的电导率时考虑了包括电子、原子和离子之间的多种相互作用. 钛的电导率的计算结果与已有的爆炸丝实验数据相符. 通过电导率随温度密度变化趋势判断, 钛在整个温度区间, 密度0.56 g·cm^-3时发生非金属相到金属相相变. 对于简并系数和耦合系数的计算分析, 钛等离子体在整个温度和密度区间逐渐从弱耦合、非简并状态过渡到强耦合部分简并态.     

Pulsed dye laser diagnostics of vacuum arc cathode spots

The ignition and arc phases of vacuum arcs were investigated using differential dye laser absorption photography with simultaneous high spatial (micrometer) and temporal (nanosecond) resolution. The discharge duration was 800 ns, the current 50-150 A, the electrode material copper, and the cathode-anode distance less than 50 μm. A 0.4 ns laser pulse (tunable, γ=480-530 nm) was used to obtain momentary absorption photographs of the cathode region. During ignition, an optically thick anode plasma expanded toward the cathode, decaying within 25 ns after bridging the electrode gap. In the arc phase, a fragmentary structure of the cathode spots was observed in situ for the first time. The microspots have a characteristic size of 5-10 μm. They appear and disappear on a nanosecond time scale. The plasma density of the microspots was estimated to be greater than (3-6)×10²⁶ m^-3     

Importance of high local cathode spot pressure on the attachment ofthermal arcs on cold cathodes

The importance of having high local cathode spot pressures for the self-sustaining operation of a thermal arc plasma on a cold cathode is theoretically investigated. Applying a cathode sheath model to a Cu cathode, it is shown that cathode spot plasma pressures ranging 7.4-9.2 atm and 34.2-50 atm for electron temperatures of ~1 eV are needed to account for current densities of 10⁹ and 10¹⁰ A·m^-2, respectively. The study of the different contributions from the ions, the emission electrons, and the back-diffusing plasma electrons to the total current and heat transfer to the cathode spot has allowed us to show the following. 1) Due to the high metallic plasma densities, a strong heating of the cathode occurs and an important surface electric field is established at the cathode surface causing strong thermo-field emission of electrons. 2) Due to the presence of a high density of ions in the cathode vicinity, an important fraction of the total current is carried by the ions and the electron emission is enhanced. 3) The total current is only slightly reduced by the presence of back-diffusing plasma electrons in the cathode sheath. For a current density j_tot=10⁹ A·m^-2 , the current to the cathode surface is mainly transported by the ions (76-91% of j_tot while for a current density j_tot = 10¹⁰ A·m^-2, the thermo-field electrons become the main current carriers (61-72% of j_tot). It is shown that the cathode spot plasma parameters are those of a high pressure metallic gas where deviations from the ideal gas law and important lowering of the ionization potentials are observed     

The anode surface temperature of CuCr contacts at the limit ofcurrent interruption

This paper estimates anode surface temperature at the current interruption limit by measuring the melting time of a contact material after current interruption and simulating the anode surface temperature. As a result, the minimum anode surface temperature of CuCr(50/50) contact material was about 1750 K. We also calculated the metal vapor density between electrodes with a simplified model. The calculation results showed that the critical vapor density was about 3×10²⁰ atoms/m³. This vapor density is equivalent to the averaged pressure of 8 Pa, which is close to the value of the Paschen minimum     

A cold thermionically emitting dusty air plasma formed by radiativeheating of graphite particulates

Formation of an atmospheric pressure dusty air plasma is explored experimentally in this paper. The plasma is created by seeding an air flow with graphite particles and irradiating the particulates with a focused CO₂ laser beam. The graphite particles are, thus, heated to thermionically emitting temperatures, and average particle temperatures and average particle number densities are measured. The presence of charges is inferred both from these measured quantities using a simple theoretical transient model, and experimentally by applying a dc bias across the irradiated region. It is found that an electron density of ~6.7 × 10⁵ cm^-3 (6.7 × 10¹¹ m^-3) can be produced at steady state in the presence of O₂. This value can be increased to 3.6 × 10⁷ cm^-3 (3.6 × 10¹³ m ^-1) in the ideal case where an electron attachment to O₂ is suppressed and where a lower work function particulate is used     

含硫宽禁带Ga2Te3基热电半导体的声电输运特性

目前对宽禁带半导体热电材料的研究开始升温, 原因是本征情况下宽禁带半导体往往具有低的热导率和高的Seebeck系数. Ga₂Te₃ 是一类带有缺陷的宽禁带半导体, 其在临界温度680± 10 K和757± 10 K处会参与共析转变和包晶反应, 因此会产生反应热. 本次工作采用少量的S元素等电子替换Ga₂Te₃中的Te元素, 观察到在临界温度附近热焓的变化, 但没有相变发生. 受热焓变化的影响这类材料在临界温度附近出现了较活跃的声电输运行为, 具体表现为热容和Seebeck系数(α)明显增大及热扩散系数(热导率)和电导率下降. 例, 对于x=0.05的材料, 其α值从596 K 时的376.3(μV·K^-1)迅速增大到695 K时的608.2(μV·K^-1), 然后又随温度升高到764 K时迅速降低到213.8(μV·K^-1). 在596 K到812 K范围, Seebeck系数和电导率几乎随温度均呈Z字形变化. 这些输运行为的变化揭示了在Ga₂Te₃基半导体中声子和载流子的临界散射特点, 这种临界散射特征对以后的继续研究具有重要的参考价值.     

Plasma parameters within the cathode spot of laser-induced vacuumarcs: experimental and theoretical investigations

Cathode spot formation in laser-induced breakdown in vacuum was investigated by laser absorption photography with high spatial (0.5 μm) and temporal (100 ps) resolution. The discharge was initiated between Cu electrodes with a cathode-anode distance of 15-250 μm. The duration of pulsed discharges was 750 ns and dc discharges some milliseconds; the current was below 10 A. Picosecond momentary absorption photography yielded spatial-temporal density distributions in the ignition phase of the cathode spot. An absolute electron density >5×10²⁶ m^-3 in narrow plasma fragments with a diameter smaller than 5 μm was estimated. Mathematical modeling has satisfactorily explained the formation of the narrow plasma channel due to the bulk current self-focusing, as well as due to the generation of nonstationary emissive centers at the moving boundary of the expanding cathode spot plasma     

Photo-ionized lithium source for plasma accelerator applications

A photo-ionized lithium source is developed for plasma acceleration applications. A homogeneous column of lithium neutral vapor with a density of 2×10^15-3 is confined by helium gas in a heat-pipe oven. A UV laser pulse ionizes the vapor. In this device, the length of the neutral vapor and plasma column is 25 cm. The plasma density was measured by laser interferometry in the visible on the lithium neutrals and by CO₂ laser interferometry on the plasma electrons. The maximum measured plasma density was 2.9×10 ¹⁴ cm^-3, limited by the available UV fluence (≈83 mJ/cm²), corresponding to a 15% ionization fraction. After ionization, the plasma density decreases by a factor of two in about 12 μs. These results show that such a plasma source is scaleable to lengths of the order of 1 m and should satisfy all the requirements for demonstrating the acceleration of electrons by 1 GeV in a 1-GeV/m amplitude plasma wake     

热退火对SiO2：Er薄膜发光特性的影响

利用离子注入法制备SiO₂:Er样品,并在不同温度下进行退火处理。通过微区拉曼光谱、吸收光谱、X射线光电子能谱等手段对其进行结构表征,并进行了室温和变温的光致发光特性研究,得到了可见区和红外区的光致发光。其中,⁴S_3/2→⁴I_15/2的发光强度随温度的升高,先增强后减弱,呈现出反常的温度淬灭效应,此现象是由Er³⁺与SiO₂的缺陷之间的能量传递造成的。