Analysis of sorption into single ODS-silica gel microparticles in acetonitrile-water.

Intraparticle mass transfer processes of Phenol Blue (PB) in single octadecylsilyl (ODS)-silica gel microparticles in acetonitrile-water were analyzed by microcapillary manipulation and microabsorption methods. An absorption maximum of PB, the sorption isotherm parameters, and the sorption rate in the microparticle system were highly dependent on the percentage of acetonitrile in solution. The results are discussed in terms of the microscopic polarity surrounding PB in the ODS phase and the relationship between the isotherm parameters and the sorption rate.     

Sorption-desorption of radiocesium on various sorbents in presence of humic acid

In general, the amount of radiocesium sorbed by the five sorbents with 0.01 mol·dm^–3 NaCl was in order zeolite > NiFeCN–SiO₂ > montmorillonite > aerogel > silica gel. Addition of humic acid solution to the sorbents depressed the sorption of cesium by all sorbents, except for NiFeCN–SiO₂ was not seen, with the greatest effect showing to the aerogel. The presence of humic acid resulted in an enhanced desorption of cesium from zeolite, NiFeCN–SiO₂ and to a lesser extent from montmorillonite and silica gel. The order of cesium retention following desorption for both sorbent and sorbent/humic-acid mixtures was zeolit > NiFeCN–SiO₂ > montmorillonite > silica gel. The presence of humic acid resulted in decreasing of distribution coefficient values for both sorption and desorption processes.     

Application of HPLC capacity coefficients to characterize the sorption of polycyclic aromatic compounds to humic acid

The sorption coefficients to humic acid of 46 PAC having a wide range in polarity were compared with the capacity coefficients of the PAC to a non-polar HPLC column material (ODS) and a polar one (Diol). It is shown that polar interactions contribute to the sorption of polar PAC in addition to the non-polar interactions. The results also suggest that humic acid may contain different hydrophilic adsorption sites. The non-polar column material was only the best model substrate, if the test materials were limited to the hydrophobic unsubstituted PAC, PAH+O,S-PAC.     

New resin gel for uranium determination by diffusive gradient in thin films technique

A new resin gel based on Spheron-Oxin(?) chelating ion-exchanger with anchored 8-hydroxyquinoline functional groups was tested for application in diffusive gradient in thin film technique (DGT) for determination of uranium. Selectivity of uranium uptake from model carbonate loaded solutions of natural water was studied under laboratory conditions and compared with selectivity of the conventional Chelex 100 based resin gel. The affinity of Spheron-Oxin(?) functional groups enables determination of the overall uranium concentration in water containing carbonates up to the concentration level of 10(2) mg L(-1). The effect of uranium binding to the polyacrylamide (APA) and agarose diffusive gels (AGE) was also studied. Uranium is probably bound in both gels by a weak interaction with traces of acrylic acid groups in the structure of APA gel and with pyruvic and sulfonic acid groups in the AGE gel. These sorption effects can be eliminated to the negligible level by prolonged deployment of DGT probes or by disassembling probes after the 1-2 days post-sampling period that is sufficient for release of uranium from diffusive gel and its sorption in resin gel.     

Continuous‐Bed Columns Containing Sol‐Gel Bonded Packing Materials for Capillary Electrochromatography

Sol‐gel bonded packing materials in continuous‐bed columns have been prepared for capillary electrochromatography (CEC). Three packing materials were investigated: small‐pore Spherisorb ODS1 (3 μm, 80 Å) with octadecyl as stationary phase, small‐pore mixed‐mode Spherisorb ODS/SCX (3 μm, 80 Å) with octadecyl and propyl sulfonic acid as stationary phases, and large‐pore Nucleosil ODS (7 μm, 1 400 Å) with octadecyl as stationary phase. The characteristics of these columns were compared in terms of electroosmotic flow, efficiency, inertness, and retention factors. In contrast to columns containing sol‐gel bonded ODS, columns containing sol‐gel bonded mixed‐mode ODS/SCX generated nearly pH independent electroosmotic flow (EOF) over pH 2–9. Columns containing sol‐gel bonded large‐pore ODS produced nearly three times lower reduced plate height than those containing small‐pore ODS. Efficiencies of 220,000 plates per meter and 175,000 plates per meter were obtained from columns containing sol‐gel bonded 7 μm, 1 400 Å ODS and columns containing sol‐gel bonded 3 μm, 80 Å ODS, respectively, which are among the highest reported efficiencies for continuous‐bed columns. In CEC, over one million plates per meter and pH independent EOF are expected from continuous‐bed columns containing sol‐gel bonded 1.5 μm particles with large pores and mixed‐mode stationary phases.     

氯酚在D301树脂上吸附机理的研究

研究了酸性条件下氯酚在大孔弱碱树脂D301上的吸附机理.研究表明,在一定的吸附质浓度及pH值下,D301树脂对对氯酚和邻氯酚的吸附量与溶液平衡浓度之间存在良好的线性关系,吸附过程类似于固相萃取过程,且分配系数与相应pH值下X射线光电子能谱(XPS)测得的树脂上自由叔胺基团含量呈线性关系.     

Thermodynamics of starch-water systems: An analysis from solution-gel model on water sorption isotherms

The water sorption of several starch samples and resistant starch (RS) samples were analyzed using an equilibrium solution-gel structure model and the results were compared to various sorption theories. It is found that the water sorption relations to water activity in starch in the high water content region could be properly described by the equilibrium two-phase structural model. The results suggested that favorable starch-starch interaction determined the formation of starch gel in water. The gel structure had a high molecular modulus of 10⁸ Pa and thus had limited water sorption capability. Part of the starch also exhibited the solution properties with water due to chain ends and defects of the gel structure. Despite the unfavorable starch-water interaction, starch-water solution might be formed due to the predominant contributions from the entropy of mixing. The solution phase was responsible for the rapid increase of water sorption at high water activity. It was also demonstrated that the starch could maintain a maximum dynamic unfreezable water up to ≈ 36%, which was consistent with the DSC measurements. © 1996 John Wiley & Sons, Inc.     

Effect of pH and humic acid on the adsorption of cesium onto g-Al2O3

The sorption of cesium onto g-Al₂O₃ was studied by using batch technique and ultra-filtration method at room temperature, at pH 4.0, 6.0 and 8.0 and ionic strength ranged from 0.001M to 0.1M NaClO₄. The pore size of the filter 1000K was used to separate the liquid from the solid phase. UV vis spectrophotometer was used to determine the concentration of humic acid in the solution at wavelength of 254 nm. The sorption of humic acid and Cs on the g-Al₂O₃ was studied in the pH range from 2 to 12. The sorption of humic acid on the g-Al₂O₃ was strong (»98% HA was sorbed on the surface of g-Al₂O₃ below pH 9) and strongly depended on the pH values (above pH_zpc the sorption of HA decreased markedly with the increasing of pH), humic acid has a little negative effect on the sorption of cesium. This may be attributed to the formation of HA-Cs complexation in the solution. The sorption of Cs onto g-Al₂O₃ was weak depending on the pH and independent on the ionic strength. The sorption of Cs onto g-Al₂O₃ may be contributed to cation exchange and surface complexation mechanism.     

Sorption of Am(III), U(VI) and Cs(I) on sodium potassium fluorophlogopite, an analogue of the fluorine mica mineral

The sorption of ²⁴¹Am, ²³³U and ¹³⁷Cs from nitric acid solutions on a synthesized sodium potassium fluoro-phlogopite (SPFP) gel, structurally close to the fluorine mica mineral, has been studied. The synthesized gel was characterized by energy dispersive spectrometry, X-ray powder diffraction pattern, FTIR and thermogravimetric analysis and has a composition of Na_0.5K_0.5Mg₃(Si₃AlO₁₀)F₂.6H₂O. Different parameters like contact time, acid concentration, amount of SPFP, metal ion concentrations, effect of competing cations, desorption of the nuclides from the loaded SPFP gel etc., were studied using batch technique. Also, the SPFP gel was loaded with Eu(III), U(VI) and Cs(I) and the amounts sorbed on the gel has been estimated by difference from the concentrations in the original solution and those remaining in the solution after loading. Na, K, Mg, Eu and U were estimated by ICP-AES and Cs by electrothermal atomization atomic absorption spectrometry. The exchange of Na, K and Mg with the loaded cations has been evaluated and discussed in the light of ion exchange and surface precipitate sorption mechanisms.     

Sorption of Paraquat and 2,4-D by an Oscillatoria Sp.-Dominated Cyanobacterial Mat

The present study characterises sorption of two pesticides, namely, paraquat (PQ) and 2,4-dichlorophenoxyacetic acid (2,4-D) by an Oscillatoria sp.-dominated cyanobacterial mat. Sorption of PQ onto the test mat was not significantly affected by the pH of the solution within the pH range 2–7. However, 2,4-D sorption was strongly influenced by the solution pH and was maximum at pH 2. Whereas PQ sorption increased with increase in temperature, 2,4-D sorption showed an opposite trend. The sorption of PQ and 2,4-D achieved equilibrium within 1 h of incubation, independent of concentration of pesticide and mat biomass in the solution. The pseudo-second-order kinetic model better defined PQ sorption than the pseudo-first-order model, whereas 2,4-D sorption was well defined by both the models. Sorption isotherms of both the pesticides showed L-type curve. Freundlich model more precisely defined PQ sorption than Langmuir model, thereby suggesting heterogeneous distribution of PQ binding sites onto the biomass surface. However, the Langmuir model more correctly defined 2,4-D sorption, thus, indicating homogeneous distribution of 2,4-D binding sites onto the biomass surface. The test biomass is a good sorbent for the removal of PQ because it could, independent of pH of the solution, sorb substantial amount of PQ (q _max = 0.13 mmol g⁻¹).     

亲水/疏水半互穿网络凝胶在直流电场作用下的响应

研究了一种亲水 疏水型半互穿网络水凝胶 (PAAc QPVPDgels)对直流电场的刺激应答 .该凝胶中的疏水型N 十二烷基聚 (4 乙烯吡啶 )溴化盐 (QPVPD)高分子链与亲水型聚丙烯酸水凝胶 (PAAc)网络通过物理缠绕复合 .由于疏水力和亲水力的共同作用 ,在接触电场下 ,该凝胶在阳极端发生消溶胀 ,疏水相互作用对消溶胀有一定的影响 ;在非接触电场下 ,该凝胶在弱碱性溶液中迅速向阴极方向弯曲 ,在弱酸性溶液中首先发生消溶胀 ,然后向阳极方向弯曲     

Selective water sorbents for multiple applications, 1. CaCl2 confined in mesopores of silica gel: Sorption properties

This paper presents sorption properties of a selective water sorbent based on mesoporous KSKG silica gel as a host matrix and calcium chloride as a hygroscopic salt. Sorption isobars, isochores and isotherms at T=20–150°C and vapor partial pressures of 8–133 mbar clearly showed two types of water sorption: 1) the formation of solid crystal hydrates at low amounts N of sorbed water, and 2) vapor absorption mainly by the salt solution at higher N. Sorption properties of CaCl₂ crystal hydrates were found to change strongly due to their impregnation into mesoporous silica gel, whereas the solution confinement to the mesopores did not change its water sorption properties with respect to the bulk solution. Isosteric sorption heat was measured to depend on water sorption and to change from 62.5 kJ/mol for solid hydrates to 42.2–45.6 kJ/mol for solution.     

Sorption of hypoiodous acid on activated carbon

In spite of good adsorption characteristics of activated carbon for molecular iodine, from water solution, problems arising due to complexity of chemistry of iodine and hydrolysis as well as influences of other relevant factors in water solutions which easily change the equilibrium concentrations toward domination of species with lower absorbability. Sorption of hypoiodus acid as predominant chemical form of iodine in neutral and weak alkaline solution within the range of micro concentrations has been studied in great details. In the experiments sorption of hypoiodous acid from water solutions on activated carbon with surface area of 1000 m²/g, under static and dynamic conditions, has been performed. Isotherms on various temperatures (25°C, 50°C, 70°C) has been obtained. Parameters of the sorption are determined and mechanism of adsorption of hypoiodous acid molecules on activated carbon has been discussed.     

Selective Pre-concentration and Solid Phase Extraction of Mercury（Ⅱ） from Natural Water by Silica Gel-loaded （E）-N-（1-Thien-2＇-ylethylidene）-1,2-phenylenediamine Phase

Silica gel-loaded （E）-N-（1-thien-2＇-ylethylidene）-1,2-phenylenediamine （TEPDA） phase was synthesized based on physical adsorption approaches. The stability of a chemically modified TEPDA especially in concentrated hydrochloric acid that was then used as a recycling and preconcentration reagent allowed the further uses of silica gel-loaded immobilized TEPDA phase. The application of this silica gel-loaded phase to sorption of a series of metal ions was performed by using different controlling factors such as the pH of the metal ion solution and the equilibration shaking time by the static technique. This difference was interpreted on the basis of selectivity incorporated in these sulfur containing silica gel-loaded TEPDA phases. Hg（Ⅱ） was found to exhibit the highest affinity towards extraction by these silica gel-loaded TEPDA phases. The pronounced selectivity was also confirmed by the determined distribution coefficients （Kd） of all the metal ions, showing the highest value reported for mercury（Ⅱ） extraction by the silica gel immobilized TEPDA phase. The potential applications of the silica gel immobilized TEPDA phase to selective extraction of mercury（Ⅱ） from aqueous solution were successfully accomplished and preconcentration of low concentration of Hg（Ⅱ） （30 pg·mL^-1） from natural tap water with a preconcentration factor of 200 for Hg（Ⅱ） off-line analysis was conducted by cold vapor atomic absorption analysis.     

Synthesis of penetrable macroporous silica spheres for high-performance liquid chromatography

Silica microspheres have been synthesized by phase separation and sol–gel transition coupled with emulsion method. The as-obtained material is characterized by scanning electron microscopy, nitrogen sorption, elemental analysis and particle size distribution measurements. The results demonstrated that the material featured with hierarchically porous structure, possessing both mesopores and penetrable macropores. The mesopores provide large surface area while the macropores traverse the silica particles, which may facilitate fast mass transfer as well as guarantee low backpressure when such materials are used for packed high-performance liquid chromatography (HPLC) column. Therefore, their preliminary applications as HPLC packings in fast separation and low-pressure separation have been attempted in the present study. Benzene, benzaldehyde and benzyl alcohol were separated within two minutes on the silica column at a flow rate of 7 mL min⁻¹. Vitamin E mixtures can also be baseline separated at a high flow rate of 8 mL min⁻¹. In addition, thirteen aromatic hydrocarbons were well separated on the octadecyl-bonded silica (ODS) column. In comparison with a commercial Kromasil ODS column, the pressure of the proposed column is much lower (<1/2) under the same chromatographic conditions, while comparable separation efficiency can be achieved.     

Regularities of the sorption of cycloalkenyl-substituted thiophenes and 2,2′-bithiophenes from water-acetonitrile solutions on hexadecyl silica gel under conditions of high-performance liquid chromatography

Regularities of the sorption of newly synthesized cycloalkenyl-substituted thiophenes and 2,2′-bithiophenes from water-acetonitrile solutions of different compositions on hexadecyl silica gel are investigated by high-performance liquid chromatography (HPLC). The retention factors and Henry constants of adsorption of these substances are determined. We discuss the effect of the molecular structure of the investigated heterocycles, and the nature and positions of the substituents, on the sorption. The equilibrium constants for the quasi-chemical reactions of sorption of the investigated compounds at the interface, and their solvation in a multicomponent bulk solution, are calculated using the Lanin-Nikitin equation. Based on the obtained results, we suggest that structural self-organization in the bulk solution and at the interface with the hydrophobic surface of hexadecyl silica gel plays an important part in the sorption of cycloalkenylsubstituted thiophenes and 2,2′-bithiophenes from multicomponent solutions.     

A flow-through solid-phase spectroscopic sensing device implemented with FIA solution measurements in the same flow cell: determination of binary mixtures of thiamine with ascorbic acid or acetylsalicylic acid

A continuous and simple UV-photometric flow-through optosensor has been developed for the simultaneous determination of a binary mixture of two species with different electric charges present at very different concentrations - ascorbic acid (or acetylsalicylic acid) and thiamine. The sensing device is based on the selective sorption and determination of a cationic analyte on a cation-exchange gel (Sephadex SP-C25) while the other, anionic, analyte is determined in the solution among the interstices of the cation-exchange gel in the same flow cell. The analytes arrive in sequence at the sensing zone, which detects their intrinsic absorbance at 253 nm, as a result of on-line separation by use of a minicolumn filled with the same cation-exchange gel as in the cell, and placed before the flow cell. Thiamine is retained in the minicolumn whereas ascorbic acid or acetylsalicylic acid pass through it and produce their signal as a result of absorbance in the interstitial solution among the resin beads. Thiamine is then eluted from the precolumn, transported to the flow cell, and temporarily retained in the sensing zone from this eluted solution. Calibration graphs were linear over the range 3-50, 25-400, and 300-3000 microg mL(-1) (600 microL sample volume) and the relative standard deviations were 2.56, 1.85, and 1.25 % for thiamine, ascorbic acid, and acetylsalicylic acid, respectively. The proposed method was satisfactorily applied to the determination of binary mixtures of thiamine with ascorbic acid or acetylsalicylic acid in pharmaceutical preparations and semi-synthetic samples.     

Ion-exchange recovery of nickel(II) and cobalt(II) from sulfuric acid solutions

Sorption recovery of nickel(II) and cobalt(II) in their joint presence in sulfuric acid solutions was studied on new samples of domestic ion exchangers of CYBBER brand. It was shown that the ion exchangers under study have a high sorption capacity for ions of both nonferrous metals, depending on the structure of a sorbent and on the acidity of a contacting solution. It was found that, after Co(II) and Ni(II) ions are extracted from weak or strong sulfuric acid solutions, they can be effectively eluted from the ion exchangers under study with a 2 M hydrochloric acid solution to an extent of 85–95% (nickel) and 87–95% (cobalt).     

Preparation and retention characteristics of different phenyl phases for reversed-phase liquid chromatography

Summary Three different phenyl phases were prepared. The amount of organic moiety bound on silica support was determined from thermogravimetric curves of the modified silica gel. The specific surface areas of gels were obtained from nitrogen sorption measurement at –196°C. The effect on separation and selectivity of the different bonded-phenyl functional groups was studied. The selectivity of the phenyl-bonded silica gels was examined and compared with octadecyl (ODS) silica in liquid chromatography. Corresponding to the high surface concentration of functional groups, the capacity factors of solutes, normalized to unit surface area of the adsorbent, k/S_BET were found to decrease in the sequence phenylmethyl>diphenyl>triphenyl. Polar solutes are retained in greater extent on the phenyl phases than on the ODS phase.     

Humic acid sorption onto a quartz sand surface: A kinetic study and insight into fractionation

A kinetic study of Aldrich humic acid sorption onto a quartz sand surface has revealed an initial rapid uptake of humic acid molecules followed by a much slower sorption. The humic acid molecular weight and chemical fractionation resulting from adsorption onto the simple quartz sand surface were investigated for the two kinetic steps by coupled asymmetric flow-field flow fractionation-UV/visible absorption spectrophotometry. The molecular weight distribution of residual humic acid in solution after adsorption deviated from the original molecular weight distribution, showing preferential adsorption of certain molecular weight components. This fractionation is different after the two kinetic steps. Humic acid molecules characterised by a molecular weight below 4800 Da and with a weight-average molecular weight (M(w)) of 1450 Da were adsorbed after the fast kinetic step, whereas humic acid molecules in the molecular weight range 1400-9200 Da and of M(w) 3700 Da were adsorbed after the slower uptake. Therefore, the adsorption of low molecular weight humic components takes place initially, and is then followed by the adsorption of higher molecular weight components. Chemical adsorptive fractionation, investigated by studying the 253 nm/203 nm absorbance ratio over time, shows that aromatic components are preferentially adsorbed during the fast kinetic step. The fractionation pattern may be explained by the physicochemical characteristics of the Aldrich humic acid and the underlying sorption processes. The trend for the sorption kinetics of europium onto the quartz sand surface in the presence of humic acid is similar to that of the humic acid itself.