Polymerization of coordinated monomers. V. Polymerization of methyl methacrylate–Lewis acid complexes

The polymerization of the complex of methyl methacrylate with stannic chloride, aluminum trichloride, or boron trifluoride was carried out in toluene solution at several temperatures in the range of 60° to ?78°C by initiation of α,α′-azobisisobutyronicrile or by irradiation with ultraviolet rays. The tacticities of the resulting polymers were determined by NMR spectroscopy. Both the 1:1 and the 2:1 methyl methacrylate–SnCl₄ complexes gave polymers with similar tacticities at the polymerization temperatures above ?60°C. With decreasing temperature below ?60°C, the isotacticity was more favored for the 2:1 complex, whereas the tacticities did not change for the 1:1 complex. On the ESR spectroscopy of the polymerization solution under the irradiation of ultraviolet rays at ?120°C, the 1:1 SnCl₄ complex gave a quintet, while the 2:1 SnCl₄ complex gave both a quintet and a sextet. The sextet became weaker with increasing temperature and disappeared at ?60°C. This behavior of the sextet corresponds to the change of the tacticities of polymer for the 2:1 SnCl₄ complex. An intra–intercomplex addition was suggested for the polymerization of the 2:1 complex, which took a cis-configuration on the basis of its infrared spectra. The sextet can be ascribed to the radical formed by the intracomplex addition reaction, while the quintet can correspond to that formed by the intercomplex addition reaction. The proportion of the intracomplex reaction was estimated to be about 0.25 at ?75°C, and the calculated value of the probability of isotactic diad addition of the intracomplex reaction was found to be almost unity.     

Crystallization during polymerization of poly-p-xylylene. II. Polymerization at low temperature

The polymerization of p-xylylene was followed with a newly designed differential thermal analysis system at temperatures between ?196°C and ?20°C. It was found that at the lower temperatures the monomer condenses first to the crystalline monomer before simultaneous polymerization and crystallization. At the higher temperatures, polymerization and crystallization are successive. The data are in agreement with the morphology and crystal structure data derived in Part I of this series of papers on crystallization during polymerization of poly-p-xylylene.     

Polymerization of vinyl chloride at reduced monomer accessibility. II. Polymerization at subsaturation pressure with emulsion PVC as seed

Vinyl chloride was polymerized at 59–92% of saturation pressure in a water-suspended system at 45–65°C with an emulsion poly(vinyl chloride) (PVC) latex as a seed. A water-soluble initiator was used in various concentrations. The monomer was continuously charged as vapor from a storage vessel kept at lower temperature. Characterization included determination of molecular-weight distribution and degree of long-chain branching by gel permeation chromatography (GPC) and viscometry, thermal dehydrochlorination, and microscopy. The polymerization rate decreases with decreasing pressure but is reasonable even at the lowest pressure. The molecular weight decreases with decreasing pressure and increasing initiator concentration and also with increasing polymerization temperature, if the initiator concentrations are chosen to give a constant initiator radical concentration. The degree of long-chain branching increases with increasing initiator concentration and decreasing monomer pressure but is unaffected by the polymerization temperature, if the initiator radical concentration is kept constant. The thermal stability decreases with decreasing M _n, while the degree of long-chain branching has only a minor influence. The most important factor in the system influencing the molecular parameter is the monomer accessibility.     

Polymerization of aromatic aldehydes. II. Cationic cyclopolymerization of phthalaldehyde

Phthalaldehyde was found to undergo cyclopolymerization with ease by several cationic catalysts and by γ-ray irradiation. The polymer was composed entirely of the dioxyphthalan unit, as confirmed by infrared spectroscopy and ready decomposition to monomer. The enhanced polymerizability of phthalaldehyde as compared with other aromatic aldehydes was explained in terms of the intermediate-type or, preferably, concerted propagation scheme. The conversion reached a saturation value of 87% in about 1 hr in methylene chloride at ?78°C, indicating an equilibrium polymerization. The ceiling temperature of the polymerization was ?43°C, as estimated from the relation between the saturation yield and polymerization temperature. The enthalpy and entropy of propagation were ?5.3 kcal/mole and ?23.0 eu, respectively. Since the molecular weight of the polymer was proportional to conversion, the propagating chain end was considered to be “living” in this system. The rate constant for propagation was calculated to be 0.18 1/mole-sec in methylene chloride at ?78°C with BF₃OEt₂ catalyst.     

Atom Transfer Radical Polymerization of N,N‐Dimethylacrylamide

Summary: The living polymerization of N,N‐dimethylacrylamide was achieved by atom transfer radical polymerization catalyzed by copper chloride complexed with a new ligand, N,N′‐bis(pyridin‐2‐ylmethyl 3‐hexoxo‐3‐oxopropyl)ethane‐1,2‐diamine (BPED). With methyl 2‐chloropropionate as the initiator, the polymerization reached high conversions (> 90%) at 80 °C and 100 °C, producing polymers with very close to theoretical values and low polydispersity. The ligand, temperature, and copper halide strongly affected the activity and control of the polymerization.

PDMA molecular weight and polydispersity dependence on the DMA conversion in the DMA bulk polymerizations at different temperatures: DMA/CuCl/MCP/BPED = 100/1/1/1, 100 °C (♦, ⋄); 80 °C (▴, ▵); 60 °C (▪, □); and DMA/CuCl/MCP/BPED = 100/1/1/2, 80 °C (•, ○).     

Metal-containing initiator systems. VI. Polymerization of butadiene with metal–organic halide systems

The polymerization of butadiene with binary initiator systems consisting of some activated metals and organic halides was investigated at 60°C. From the results obtained, it was found that systems of reduced nickel and methyltrichlorosilane or dimethyldichlorosilane were most effective for the polymerization, and those of reduced nickel and carbon tetrachloride, benzyl chloride, benzyl bromide and benzoyl chloride, showed moderate activity. The polybutadienes obtained with these systems were observed to contain product of more than 80% cis-1,4 microstructure. From detailed studies on the reduced nickel–methyltrichlorosilane system, these polymerization mechanisms were explained by the hypothesis that the initiation occurred through the reaction of the dissociated transition state complex with the monomer or with a trace amount of water, and then the propagation proceeded via a coordinated cationic mechanism. These systems did not show a good activity for the cis-1,4 polymerization of isoprene.     

Polymerization of aromatic aldehydes. IV. Cationic copolymerization of phthalaldehyde isomers and styrene

Copolymerizations of three phthalaldehyde isomers (M₂) with styrene (M₁) were carried out in methylene chloride or in toluene with BF₃OEt₂ catalyst. The monomer reactivity ratios were r₁ = 0.77, r₂ = 0 for the meta isomer and r₁ = 0.60, r₂ = 0 for the para isomer. The second aldehyde group of both isomers did not participate in polymerization and acted simply as the electron-withdrawing group, thus reducing the cationic reactivity of these monomers. Copolymerization behaviors of the ortho isomer (o-PhA) were quite different between 0°C and ?78°C. At ?78°C, o-PhA preferentially polymerized to yield “living” cyclopolymers, until an equilibrium concentration of o-PhA monomer was reached. Then, styrene propagated from the living terminal rather slowly. The block structure of the copolymer was confirmed by the chemical and spectroscopic means. In the copolymerization at 0°C, the o-PhA unit in copolymer consisted both of cyclized and uncyclized units. This copolymer seemed to contain short o-PhA sequences. The variation of the o-PhA-St copolymer structure with the polymerization temperature was explained on the basis of whether the polymerization was carried out above or below the ceiling temperature (?43°C) of the homopolymerization of o-PhA.     

Polymerization of vinyl chloride by alkyllithium compounds

The polymerization of vinyl chloride initiated by alkyllithium compounds was investigated. The effect of temperature, initiator concentration, and monomer concentration on the conversion and the properties of the resulting polymers were studied. The optimum temperature in the investigated range (between ?20°C and +20°C) was +5°C. The conversion is directly proportional to the concentration of both the initiator and the monomer. The molecular weight is inversely proportional to the initiator concentration and directly proportional to the monomer concentration. Under optimum conditions the molecular weight of the polymers is as high as 140,000. These results differ by an order from hitherto published data on the nonradical polymerization of vinyl chloride. The proportion of isotactic and syndiotactic structures resulting from the presence of tert-butyllithium does not differ from that obtained by radical polymerization, but the occurrence of anomalous structures is reduced to a minimum. The stability of the macromolecules is higher. A mechanism of the polymerization is suggested.     

Living Carbocationic Polymerization of Styrene in the Presence of Proton Trap

Abstract

The living polymerization of styrene was achieved with the 2,4,4-trimethyl-2-pentyl chloride/TiCl₄/MeCl:methylcyclohexane 40:60 v:v/?80°C polymerization system in the presence of di-tert-butylpyridine in concentrations comparable to the concentration of protic impurities. It was determined that the living nature of the polymerization is not due to carbocation stabilization. The polymerization is second order in TiCl₄. Side reactions, namely polymerization by direct initiation and intermolecular alkylation, are operational, and a careful selection of experimental conditions is necessary to minimize their effect and obtain apparently living behavior. Polymerization by direct initiation can be minimized by increasing the initiator concentration, and intermolecular alkylation can be reduced by quenching the polymerization system when the conversion reaches close to 100%.     

Gamma Ray Induced Low Temperature in Situ Polymerization of Vinyl Chloride and Copolymfrization of Vinyl Chloride-Vinyl Acetate in Taiwan-Produced Woods

Gamma radiation induced polymerization of vinyl chloride (VC) and copolymerization of vinyl chloride (VC)-vinyl acetate (VAc) in Taiwan cedars have been investigated at low temperatures. The polymerization-rate of VC and the copolymerization-rate of VC-VAc system in wood were found to be proportional to the n powers of the dose-rate, where n became close to the value of 1 as the polymerization temperature being lowered below 0°C. The oxygen in air was recognized to induce the delay of the induction period due to its retardation on the polymerization. The apparent activation energies of VC and VC-VAc for the polymerization and the copolymerization in wood were determined by use of the Arrhenius plotting as 4.0 Kcal/mole and 3.4 Kcal/mole respectively at the temperature-range of —15°C～20°C. The degree of polymerization of VC was greatly affected by the polymerization temperature, although it was observed to be independent on the total gamma dose within 1 Mrad and the kinds of wood. No graft reaction of PVC polymer and PVC-PVAc copolymer onto the wood cellulose was found, while low graft percentage of about 3% being obtained at 20° C in the case of using swelling agents. However, this value was found to be decreased to 0.1% at the temperature of —15°C. Based on the above-mentioned experimental results, the radiation induced low temperature polymerization of VC or copolymerization of VC-VAc system in Taiwan produced cedars are considered to proceed with radical polymerization mechanism.     

Suspension polymerization of vinyl chloride initiated by in situ generated diisobutyryl peroxide

It was found that diacyl peroxides can be formed in situ in a polymerization medium by the reaction of an acid anhydride with hydrogen peroxide. For the specific application to aqueous vinyl chloride polymerization, an initiator system based on the base-catalyzed reaction of isobutyric anhydride with hydrogen peroxide to produce diisobutyryl peroxide gave very good results. In contrast, the acid chloride was completely ineffective as a peroxide precursor in this reaction. Studies pointing to diisobutyryl peroxide as the initiating species; investigations of reactant stoichiometry; and comparison of the in situ system with preformed diisobutyryl peroxide were conducted. It was shown that this system makes possible the polymerization of vinyl chloride at 30°C at rates comparable to those obtained with dialkyl peroxydicarbonates at 50°C, thus demonstrating the ability of this system to initiate vinyl chloride polymerization at low temperature. The rates of vinyl chloride polymerization with the use of different concentrations of in situ diisobutyryl peroxide at 30, 40, and 50°C were determined. Similarly, polymerization rates with the use of combinations of in situ diisobutyryl peroxide and n-propyl peroxydicarbonate were determined. The data obtained demonstrate rapid initiation of the polymerization reaction and a reduction in polymerization time made possible by this dual initiator system. These results were verified in pilot-plant and commercial-scale PVC polymerizations.     

Aminobutadienes. VI. Polymerization and Copolymerization of 2-Phthalimido-1,3-butadiene

2-Phthalimido-1,3-butadiene (2-PB) was polymerized either radically or thermally in bulk and in solution. While the polymer obtained by solution polymerization was soluble in some solvents such as halogenated hydrocarbons, dioxane, and dimethylformamide and had a softening point in the range of 160–170°C., that obtained by polymerization in bulk was insoluble in any solvent and only swollen on being immersed in such solvents as above. The reduced viscosity of the soluble polymer obtained by solution polymerization was approximately 1.0, and this value remained almost unchanged with varying polymerization time. Likewise the cationic polymerization in acetylene tetrachloride or in chloroform at 20°C. with the use of cationic catalysts such as boron trifluoride and stannic chloride was attempted, but no formation of polymer was observed. This monomer preferentially reacted with acrylonitrile, methyl methacrylate, styrene, and N-vinylphthalimide to form the respective copolymers; it reacted somewhat less readily with vinyl acetate. The monomer reactivity ratios in the copolymerization with styrene were calculated by the Fineman and Ross method and found to be r₁ (2-PB) = 5.2 and r₂ (styrene) = 0.11, respectively, from which the Q, e parameters were successively evaluated to be Q = 5.0 and e = ?0.05. The fact that e value is close to zero, easily explains why this monomer can copolymerize well both with acrylonitrile, which has a highly positive value of e (1.2) and with styrene, for which e is considerably negative (-0.8).     

Polymerization of phenylacetylene by triethyl aluminum and titanium tetraethoxide

The polymerization of phenylacetylene to polyphenylacetylene was accomplished with the combined catalysts triethyl aluminum and titanium tetraethoxide. The progress of the reaction was monitored by gas chromatography. The parameters included temperature (?80, 25, 140°C), solvent (benzene, chlorobenzene, toluene, cyclohexane, and nitrobenzene), mole ratio of catalysts (Al/Ti; 1.5, 3.0, 4.5, 6.0, and 9.0), aging times of catalysts (2, 10, and 40 min), and order of addition of reagents. Derivatives of polyphenylacetylene were obtained by the acylation of polyphenylacetylene with p-nitrobenzoyl chloride, the sulfonation of polyphenylacetylene with benzenesulfonyl chloride, and the formation of polyphenylacetylene complexes with complexing agents such as bromine, iodine, iodine chloride, boron trifluoride, and ferric chloride. A new phenylacetylene-acetylene product mixture was produced by the polymerization of phenylacetylene and acetylene at 25 and ?80°C. The electrical conductivity of polyphenylacetylene and its derivatives is in the range of 10^?10?10^?3 Ω^?1 cm^?1.     

Cyclopolymerization. VI. Polymerization mechanism of N-methyl-N-allylmethacrylamide at lower temperature

Mechanistic investigations on the polymerization of N-methyl-N-allylmethacrylamide (MAMA) at lower temperature were carried out based upon the ESR studies of MAMA and its monofunctional counterparts irradiated with ⁶⁰Co γ rays. Cyclopolymerizability of MAMA was also studied in connection with the hindered rotation about its amide C? N bond. The propagating radical observed is only related to the methacryl group but not to the allyl group both in MAMA and its monofunctional counterparts. Polymerization at ?78°C yielded a polymer with a lower degree of cyclization(88.8%) as compared with that of polymers formed at higher temperatures (93.5% above 0°C). A structural study revealed that the increment of the unsaturation in the poly-MAMA obtained at ?78°C is due to the allyl group and the content of pendant methacryl group is almost unchanged over the temperature range from ?78 to 120°C. These results led to the conclusion that the polymerization of MAMA at ?78°C proceeds mainly through the methacryl group, the rate-determining step is the cyclization reaction, and, in addition, cyclization reaction scarcely occurs when it polymerizes through the allyl group. Since MAMA is frozen into a glassy state, the effect of glass transition temperature (T_g) has been studied and it was suggested that the polymerization of MAMA proceeds only above T_g.     

Polymerization of vinyl chloride in the presence of precipitants. I

The kinetics of bulk and precipitation polymerization of vinyl chloride has been studied over wide range of reaction temperature by using γ-ray induced initiation. The autoacceleration effect, which has been observed by many investigators in the case of chemically initiated bulk polymerization of vinyl chloride above 40°C and has been the most controversial aspect of the bulk polymerization of vinyl chloride, was found to disappear in the bulk polymerization below 0°C. In the bulk polymerization at 40°C, the autoacceleration effect was observed up to 20%, in agreement with the results of previous investigators, and a pronounced effect of the size of polymer particles on the time–conversion curve was observed. The kinetics of precipitation polymerization of vinyl chloride in the presence of some nonsolvents was successfully described by a oneparameter equation. A kinetic scheme, which clearly explains the zero-order reaction behavior of bulk polymerization at low temperature and the kinetic behavior of precipitation polymerization described by the empirical equation, is proposed. The autoacceleration effect in the bulk polymerization at 40°C was considered to be essentially the same phenomenon as the small retardation period observed in the bulk polymerization at low temperature.     

Vinyl polymerization. 413. Polymerization of vinyl monomer initiated by poly(vinylbenzyltrimethyl)-ammonium chloride

The polymerization of vinyl monomer initiated by an aqueous solution of poly(vinylbenzyltrimethyl)ammonium chloride (Q-PVBACI) was carried out at 85°C. Styrene, p-chlorostyrene, methyl methacrylate, and i-butyl methacrylate were polymerized, whereas acrylonitrile and vinyl acetate were not. The effects of the amounts of vinyl monomer, Q-PVBACI, and water on the conversion of vinyl monomer were studied. The overall activation energy in the polymerization of styrene was estimated as 79.1 kJ mol^?1. The polymerization proceeded through a radical mechanism. The selectivity of vinyl monomer was discussed by “a concept of hard and soft hydrophobic areas and monomers.”     

Polymerization of fluorinated diacetylenes

Perfluoroalkylene diacetylenes, HC?C? (CF₂)_n? C?CH, underwent thermal polymerization at 250–350°C to give glassy polymers stable to 450°C. Partial polymerization of the volatile monomers gave oligomers that are processable at atmospheric pressure. Polymers with similar thermal stability were obtained by transition-metal-catalyzed polymerization of the monomers at moderate temperatures.     

Polymerization of α-amino acid N-carboxy anhydrides. III. Mechanism of polymerization of L- and DL-alanine NCA in acetonitrile

The polymerization of L - and DL -alanine NCA initiated with n-butylamine was carried out in acetonitrile which is a nonsolvent for polypeptide. The initiation reaction was completed within 60 min.; there was about 10% of conversion of monomer. The number-average degree of polymerization of the polymer obtained increased with the reaction period, and it was found to agree with value of W/I, where W is the weight of the monomer consumed by the polymerization and I is the weight of the initiator used. The initiation reaction of the polymerization was concluded as an attack of n-butylamine on the C₅ carbonyl carbon of NCA. The initiation, was followed by a propagation reaction, in which there was attack by an amino endgroup of the polymer on the C₅ carbonyl carbon of NCA. The rate of polymerization was observed by measuring the CO₂ evolved, and the activation energy was estimated as follows: 6.66 kcal./mole above 30°C. and 1.83 kcal./mole below 30°C. for L -alanine NCA; 15.43 kcal./mole above 30°C., 2.77 kcal./mole below 30°C. for DL -alanine NCA. The activation entropy was about ?43 cal./mole-°K. above 30°C. and ?59 cal./mole-°K. below 30°C. for L -alanine NCA; it was about ?14 cal./mole-°K. above 30°C. and ?56 cal./mole-°K. below 30°C. for DL -alanine NCA. From the polymerization parameters, x-ray diffraction diagrams, infrared spectra, and solubility in water of the polymer, the poly-DL -alanine obtained here at a low temperature was assumed to have a block copolymer structure rather than being a random copolymer of D - and L -alanine.     

Quasiliving Carbocationic Polymerization. XVII. Synthesis Of Poly (Styrene-β-Isobutylene-β-Styrene)

Poly(styrene-b-isobutylene-b-styrene) has been synthesized by sequential carbocationic polymerization under quasiliving conditions at -90°C. The quasiliving synthesis was effected by first continuously and slowly condensing gaseous isobutylene (IB) to a bifunctional initiating system (p-dicumyl chloride/TiCl₄) dissolved in a hexane-methylene chloride (60:40 v/v) mixture. After the quasiliving polyisobutylene (PIB) sequence had reached a desired molecular weight, styrene (St) was continuously and slowly added to produce the polystyrene (PSt) sequence. The products consisted of the target triblock. However, due to initiation by impurities and possibly to chain transfer to both IB and St, it also contained diblocks and small amounts of homopolymers. While the latter could be removed by selective fractionation, the triblocks and diblocks could not be separated. The mechanism of quasiliving polymerization leading to PIB/PSt blocks is discussed.     

Quasiliving Carbocationic Polymerization. V. Quasiliving Polymerization of lndene

Quasiliving polymerization of indene, i.e., an increase of the molecular weight of polyindenes with the cumulative amount of consumed monomer, has been demonstrated using the “H₂O”/ BCl₃, 2-chloroindene/BCl, “H₂O”/TiCl₄, 2-chloroindene/TiCl₄, and cumyl chloride/TiCl₄ initiating systems in CH₂Cl₂ solvent at -50°C. However, chain transfer operates in every system investigated, and sets a limit to DP _n,max. The efficiency of the 2-chloroindene and cumyl chloride initiators is very low. The behavior of BCl₃ and TiCl₄ coinitiators on the polymerization has also been investigated.