酶催化魔芋葡甘聚糖的可控降解

魔芋葡甘聚糖 (KGM)是一种来自植物的天然高分子 .它具有优异的可生物降解性和生物相容性 ,并具有许多独特的生理和药理功能 .本实验首先测定了 β 甘露糖酶在不同条件 (温度、pH值、介质 )下的活性 ,发现 β 甘露糖酶在 5 0℃左右 ,pH 9 4附近 ,乙醇含量低于 5 %的水介质中具有较高的活力 ;而在pH 7 0以下 ,或温度低于 3 0℃ ,或加入 2 0 %乙醇的条件下均基本上失活 .在此研究基础上 ,探讨了 β 甘露糖酶催化KGM降解反应的规律 ,通过调节反应条件制备了一系列分子量不同的降解样品 ,并确定了KGM的分子量与特性粘数之间的关系为 :[η]=5 0 6× 1 0 - 4M0 754w ,使得酶催化KGM的可控降解成为可能 ,从而为深入研究KGM及其衍生物的结构与性能 ,扩展其应用领域奠定了良好的理论和实验基础     

光催化降解磷酸酯类农药的研究

以TiO₂/beads作为光催化剂,研究了磷酸酯类农药光催化降解的规律.结果表明,低浓度的磷酸酯类农药光催化降解符合一级动力学方程;4.0×10^-4mol/L的敌敌畏和久效磷农药,375W中压汞灯照射1.5h,其残留量小于10%,光照3.5h,有机磷被完全光催化降解至PO₄^3-.     

国产二氧化钛在光催化降解染料废水中的应用

研究了 几种国 产和进口 二氧化钛 在光催 化降解染 料污染 物方面的 应用． Ｘ 射线 衍射 及扫描电镜 分析结果 表明,锐 钛矿型含 量高以 及粒径 小的 二氧 化钛 能很 好地 催化 降解 有机 染 料． 不同结构染 料的降 解难易顺 序为： 酞菁类 ＞ 蒽醌类 ＞ 单偶氮 类; 降解 速度 与吸 附有 直接 关系 ． 搅 拌分散体系 和糊状 体系的实 验结果表 明,难于 生物降 解的高浓 度直接耐 晒大红 ４ Ｂ Ｓ 工业 染料 废水 可被光催化 降解并 矿化,国产 催化剂 可重复利 用多次 ,光源可采 用太阳 光．     

聚对二氧环己酮-乙交酯缝合线体外降解研究

用DSC和X ray衍射法对聚对二氧环己酮 乙交酯 (PDG)缝合线的初期体外降解过程进行了研究 ,并使用纤维摄影仪对纤维在降解过程中的表面形态变化进行了观察 .研究结果表明 ,在本工艺条件下得到的PDG缝合线在体外降解过程中分为三个阶段降解 ,即无定形区降解、原纤间非晶区降解和晶区水解 .在体外降解过程中 ,PDS缝合线以横向断裂为主 ,而PDG则通过表面积的大块脱落来完成降解过程     

Low temperature degradation and characterization of natural rubber

Low temperature degradation of natural rubber was performed with potassium persulfate (K₂S₂O₈, KPS) in the latex stage at 30 °C to accomplish a good processability of the rubber. Various grades of natural rubbers were used as a source rubber. Gel content, molecular weight and chemical structure of the rubbers were characterized by swelling method, size exclusion chromatography and ¹H NMR spectroscopy, respectively. The well characterized natural rubber was subjected to oxidative degradation with KPS at 30 °C. Mooney viscosity decreased when the latex was degraded with 1.0 phr of KPS and it was dependent upon the amount of KPS. Molecular weight and gel content of the degraded natural rubber were about one-half as low as those of the source rubber. Chemical structure of the rubber was analyzed through Fourier transform infrared and ¹H NMR spectroscopic methods. The degraded natural rubber was found to contain carbonyl and formyl groups as an evidence of the oxidative degradation. Tensile strength of a vulcanizate prepared from the degraded natural rubber was the same as that prepared from the source rubber, even though the gel content and the molecular weight of the degraded rubber were distinguished from those of the source rubber.     

壳聚糖超声可控降解及降解动力学研究

通过正交实验法考察了壳聚糖溶液浓度、反应温度、超声强度以及醋酸溶液浓度对超声降解反应的影响,确定了最佳反应条件,制备了一系列不同分子量的壳聚糖.研究了壳聚糖溶液浓度、反应温度以及壳聚糖原料分子参数与降解速率常数的关系.通过红外光谱、X-射线衍射和凝胶渗透色谱对降解产物进行了表征.结果表明,超声降解壳聚糖的最佳条件为10℃,壳聚糖溶液浓度2.5g/L.降解速率常数随壳聚糖溶液浓度和反应温度的降低而增大.高分子量和低脱乙酰度的壳聚糖原料有较高的降解速率和降解速率常数,壳聚糖原料的分子量对降解速率和降解速率常数的影响大于脱乙酰度对其的影响.超声波导致了壳聚糖分子量的降低和产物晶体结构的破坏,但没有改变产物的脱乙酰度和糖残基结构.     

高分子量聚α-乙烯吡啶(P2VP)在高效GPC中机械降解的研究

<正> 高效GPC广泛地应用于测量高聚物的分子量和分子量分布,有显著的优点,取得了很好的结果。但是,我们必须考虑样品中高分子量部分的降解,因为降解的存在,会影响校正曲线的准确性,从而使计算的分子量和分子量分布产生误差。如果降解严重,则不能用高效GPC进行分子量和分子量分布的测定。本文研究高分子量的P2VP流经高效GPC的Styragel柱后的降解行为,并讨论降解的原因。     

硅橡胶热降解动力学的研究

用恒温热失重方法，研究了甲基硅橡胶（Ｓｉ—Ｏ—１），用氢氧化钾催化聚合的甲基硅橡胶（Ｓｉ—Ｏ—２），主链含环二硅氮烷的硅氮橡胶（Ｓｉ—Ｎ—１）以及它与Ｓｉ—Ｏ—１的共混物Ｓｉ—Ｏ—３和与Ｓｉ—Ｏ—２的共混物Ｓｉ—Ｏ—４的热降解反应动力学．结果表明Ｓｉ—Ｎ—１有最高的热稳定性，在氮气下，其降解反应活化能为３４４ｋＪ／ｍｏｌ．并且发现它分别与Ｓｉ—Ｏ—１和Ｓｉ—Ｏ—２的共混物的热稳定性大幅度提高．Ｓｉ—Ｏ—３在氮气下的降解活化能由未加入Ｓｉ—Ｎ—１前的１５２ｋＪ／ｍｏｌ提高到２３０ｋＪ／ｍｏｌ；Ｓｉ─Ｏ─４则由未混入Ｓｉ─Ｎ─１前的６１ｋＪ／ｍｏｌ提高到１４４ｋＪ／ｍｏｌ．我们认为这种作用机理是由于硅氮橡胶除去了微量吸附水和硅羟基并导致催化剂的离子对难于分离的结果．     

DMC聚醚的降解研究

研究DMC聚醚 (双金属催化剂的聚环氧丙烷 )的降解现象 .讨论了各种因素对降解的影响 ,以及降解中不饱和度的变化情况 .实验表明 ,DMC聚醚的降解与自由基有关 ,降解在常温下 1 5天后开始发生 ,在抗氧剂存在下受到抑制 .加入抗氧剂 1 0 1 0和 61 8可使聚醚得以稳定储存     

超临界苯类溶剂对聚苯乙烯降解的影响

在高压间歇反应器中,温度340~370℃,以苯、甲苯、乙苯和对二甲苯为超临界溶剂研究了聚苯乙烯(PS)的降解特性.苯类物质是聚苯乙烯的优良溶剂,在超临界条件下其优异的传质、传热性能使聚苯乙烯快速降解.聚苯乙烯在不同超临界溶剂中降解转化率相近,而降解产物组成差别很大,分析了不同超临界溶剂对聚苯乙烯降解过程的影响.结果表明超临界甲苯对降解过程影响最小,苯乙烯收率最高.聚苯乙烯降解过程中,高分子链断裂和解聚同时进行,结合连续分布理论建立了聚苯乙烯降解的动力学模型,得到在超临界甲苯中聚苯乙烯链端解聚活化能为138.4 kJ.mol-1.     

PHOTOINDUCED DEGRADATION AND MODIFICATION OF PHOTOFRIN II IN CELLS in vitro

Abstract— Human cells of the line NHIK 3025 were incubated with Photofrin II (PII) and exposed to light. Fluorescence- and absorption spectra of PII in the cells were measured. Light exposure resulted in a degradation of PII in the cells and changes in the shape of the fluorescence spectra. These changes are probably partly due to a photochemical modification of PII and to a relocalization of PII in the cells. Notably, a destruction of binding sites for PII on or close to proteins was caused by the light exposure. The rate of the light-induced decay of the porphyrin fluorescence intensity was only slightly increasing with the PII concentration, indicating that each porphyrin molecule is mainly degraded by photoproducts originating from itself. On the other hand, the rate of the degradation of porphyrin binding sites on the proteins increased with increasing PII concentrations.
The excitation spectrum of PII in cells has a peak at285–290 nm attributed to energy transfer from proteins to porphyrins located close to the proteins. The intensity of this peak relative to the intensity of the Soret band increases with decreasing porphyrin concentrations. This might indicate that some of the binding sites close to proteins have a higher affinity for the porphyrin than binding sites at longer distances from the proteins.     

PP-SBS共混物光氧化降解的研究

和橡胶类树脂进行共混是聚丙烯(PP)改性的重要途径之一,共混有橡胶组分的PP改性树脂在其力学性能获得改进的同时,其老化性能必然也有一定的变化,我们用红外光谱方法研究了聚丙烯和苯乙烯-丁二烯星型嵌段共聚物的共混物(PP-SBS)的光氧化降解行为。     

聚羟基烷酸酯酶降解动力学研究

研究了羟基丁酸 羟基戊酸共聚物 (PHBV)在脂肪酶中的降解行为 ,用滴定法测定降解速度并进行酶促反应动力学研究 .探讨了降解速度与酶浓度和底物浓度的数学关系和Michaelis Menten常数 ,从实验上和理论上证实了PHBV的物理形态和几何尺寸对酶降解过程的影响 ,以及实验数据与非均相动力学模型的拟合     

聚苯基不对称三嗪的热分解

用高分辨裂解气相色谱－质谱（ＨＲＰｙＧＣ－ＭＳ）考察了由对苯二眯腙和四种不同芳香族四酮合成的聚苯基不对称三嗪的热分解行为，鉴定了相应裂解产物的组成、分布及其与高分子结构的关系，并用热重法（ＴＧ）测定了它们的热分解反应动力学参数，提出了其热分解反应机理．     

Sugar cane bagasse lignin as stabilizer for rubbers: Part III—Styrene/butadiene rubber and natural rubber

The stabilizing effect of a natural antioxidant, sugar cane bagasse-lignin, on the photo-chemical, thermal and environmental degradation of styrene/butadiene rubber and of natural rubber has been studied. For natural rubber the stabilizer was investigated in various concentrations in the pure form and for styrene/butadiene rubber it was also studied in substitution for a hindered phenol in a commercially used formulation which includes a p-phenylenediamine. For the photo-degradation of natural rubber, stabilization becomes appreciable only above a stabilizer concentration of 5·0% whilst in thermal degradation a concentration of 1·0% is sufficient to increase the induction period by a factor of 3 in relation to pure rubber. For styrene/butadiene rubber the same effect occurs; a concentration of 2·0% increases the induction period for photo-degradation by a factor of 1·5 whilst 1·0% increases the induction period for thermodegradation by a factor of 26 in relation to the pure unstabilized rubber. Substitution of the hindered phenol by lignin in the commercial formulation increases the induction period for the thermal degradation by a factor of 6 in relation to the commercial sample. In the environmental ageing experiments the influence of the lower photo-stabilizing effect predominated over the strong thermostabilizing activity of the lignin for both rubbers.     

叶黄素的几类降解反应研究

类胡萝卜素是一大级一泛存在于动植物体内的四储类化合物,它们不仅颜色鲜艳,也是一类重要香味物质的前体。在Ｍ的烟０－Ｉ中已有１８种类型的胡萝卜素被分离和日表征。其中卜胡萝卜素和叶黄素是主要成分ｌ‘］。烟叶采收后,类胡萝卜素经生物降解,会生成一系列有挥发性芳香化合物,它什对卷烟的吸味、品质有很大的影响Ｉ２］。本文设计了四种化学方法,对叶黄素进行氧化降解,产物用ＧＣ／ＭＳ进行检测。结果表明,在适当条件下对叶黄素进行化学法氧化降解,可以得到如：氢化异佛尔酮、环氧紫萝兰酮、二氢弥猴桃内＠纺ｏ茶香螺酮等有重要…     

VARIATION OF PHYSICO-CHEMICAL PROPERTIES OF RADIATION CROSSLINKED RUBBER WITH STORAGE TIME

The effect of storage on physico-chemical properties of non-irradiated natural rubber and radiation vulcanized natural rubber （RVNR） were evaluated. The rubber films were stored under two different conditions, namely in open air and sealed polyethylene bags. The antioxidant, tris（nonylated phenyl） phosphite （TNPP） was used for preventing degradation of RVNR films. Gel content, cross-link density, tensile strength at break and 500% elongation of rubber films were measured. The results show that the retention （%） of tensile properties of rubber films with TNPP is higher than that of rubber films without antioxidants. The rubber films stored in polyethylene bags also show better retention of tensile properties than those of rubber films stored in open air.     

STUDY OF DEGRADATION MECHANISM AND PACKAGING OF ORGANIC LIGHT EMITTING DEVICES

Organic Light Emitting Devices (OLED) have attracted much attention recently, for their applications in futureFlat Panel Displays and lighting products. However, their fast degradation remained a major obstacle to theircommercialization. Here we present a brief summary of our studies on both extrinsic and intrinsic causes for the fastdegradation of OLEDs. In particular, we focus on the origin of the dark spots by "rebuilding" cathodes, which confirms thatthe growth of dark spots occurs primarily due to cathode delamination. In the meantime, we recapture the findings from thesearch for suitable OLED packaging materials, in particular polymer composites, which provide both heat dissipation andmoisture resistance, in addition to electrical insulation.     

OXIDATIVE DEGRADATION OF LIGNIN BY PHOTOCHEMICAL AND CHEMICAL RADICAL GENERATING SYSTEMS

Oxidation of specifically radiolabeled ¹⁴C-lignins by UV/H₂0₂. Fenton's reagent, photosesitizing riboflavin. UV- and γ-irradiation was examined. In the presence of UV/H₂O₂, a hydroxyl radical (·OH) generating system. ¹⁴C-methoxy. 2-[¹⁴C-sidechain] and ¹⁴C-ring labeled lignin were rapidly and extensively degraded as measured by gel filtration of the reaction products on Sephadex LH-20. This suggested that exposure to OH leads to rapid, nonspecific lignin degradation. Rapid degradation of 14C-methoxy, 2-[¹⁴C-sidechain] and ¹⁴C-ring labeled lignin also occurred in the presence of the ·OH generating system, Fenton's reagent, confirming the primary role of ·OH in these reactions. Photosensitizing riboflavin, also capable of effecting transformation of organic compounds via Type I hydrogen radical abstractions, caused extensive oxidative degradation of ¹⁴C-methoxy labeled lignin and significant degradation of 2-(¹⁴C-sidechain] and ¹⁴C-ring labeled lignin. In addition, UV- and γ-irradiation caused slower but extensive degradation of the polymers, probably via radical type mechanisms. All of these results indicate that ·OH as well as organic radical generating systems are effective agents for the purpose of degrading this heterogeneous, optically inactive and random biopolymer.     

THE FTIR STUDIES OF PHOTO-OXIDATIVE DEGRADATION OF POLYPROPYLENE

The photo-oxidative degradation process of polypropylene film containing iron ions was investigated via FTIR and absorbance substraction technique. It is shown that the iron ions play an important role in the decomposition of hydroperoxide and the increase of the degradation rate of polypropylene film. The amorphous region of PP film undergoes degradation prior to the crystalline one.