Giant magnetoimpedance in glass-covered amorphous microwires at microwave frequencies

In this work, results on the giant magnetoimpedance (GMI) of a glass-covered amorphous microwires with nominal compositions Co_70.4Fe_4.6Si₁₅B₁₀ and Fe_77.5Si_7.5B₁₅ are presented. The impedance Z=R+iX has been investigated as function of frequency (up to 1.8 GHz) and magnetic field (up to ±400 Oe), using a HP4396B impedance analyzer and an appropriate coaxial microwave cavity. The effects of the thermal treatments (Joule heating, from 20 mA up to 100 mA for 10 min) for anisotropy induction and, as a consequence, for GMI effect have been investigated.     

Giant magneto-impedance effect in CoMnSiB amorphous microwires

The giant magneto-impedance (GMI) ratio, ΔZ/Z=[(Z(H)−Z(H_max)]/Z(H_max), in a nearly zero magnetostrictive Co_68.5Mn_6.5Si₁₀B₁₅ amorphous microwire has been investigated for the frequency range 0.5–10 MHz, driving current amplitude of 0.5–2.5 mA, bias DC magnetic field up to 2400 A/m and under applied tensile stress up to 132 MPa. A maximum relative change in the GMI ratio up to around 130% is observed at a frequency of 10 MHz, magnetic DC field of about 180 A/m, driving current amplitude of 1 mA and under tension of 60 MPa. The tensile stress dependence of the magnetic field, H_m, corresponding to the maximum ΔZ/Z ratio allows to estimate the magnetostriction constant (λ_s≈−2×10⁻⁷) to be in good agreement with λ_s values estimated by different methods and in amorphous alloys with similar compositions.     

Fast domain wall dynamics in amorphous and nanocrystalline magnetic microwires

We have studied the effect of thermal treatment on the domain wall dynamics of FeSiB and FeCoMoB microwires. It was shown that annealing in transversal magnetic field increases the domain wall mobility as well as the domain wall velocity. Annealing under the tensile stress hinders the appearance of the monodomain structure but application of tensile stress leads to the magnetic bistability having the domain wall mobility twice higher that in as-cast state. Further increase of the tensile stress reduces the domain wall mobility but the domain wall velocity increases as a result of the decrease of critical propagation field. Annealing of the FeCoMoB microwire by Joule heating leads to introduction of the circular anisotropy that favors the vortex domain wall. Such treatment increases the domain wall mobility as well as the maximum domain wall velocity.     

Structural characterization and magnetoimpedance effect in amorphous and nanocrystalline AlGe-substituted FeSiBNbCu ribbons

Two series of rapidly solidified FINEMET (Fe_73.5Si_13.5B₉Nb₃Cu₁) alloys with and without partial substitution of Al (1.5 at%)/Ge (1 at%) were prepared by melt-spinning technique. The nanocrystallization process was carried out by the heat treatment of the as-spun ribbons at 560 °C for 1 h in a vacuum furnace. X-ray diffraction (XRD), transmission electron microscopy (TEM), differential scanning calorimeter (DSC), Mössbauer spectroscopy, and magnetoimpedance (MI) measurements were conducted on the as-quenched and heat-treated alloys to investigate their structural and magnetic properties. The average crystallite sizes obtained for the heat-treated samples were in the range of 10–12 nm as confirmed by our XRD and TEM data. The ultrasoft magnetic behavior observed for the Al/Ge-substituted nanocrystalline alloys was confirmed both by our magnetic data and magnetoimpedance ratio (MIR%) results. A twofold increase in the magnitude of the MIR% (99%) was observed for the Al/Ge-substituted nanocrystalline alloy against that of the pure FINEMET alloy (∼48%) measured at 5.5 MHz. This is believed to be related to the decrease of the magnetocrystalline anisotropy as well as magnetostriction decline due to the Al substitution for Fe atoms in this nanostructured alloy.     

Structural and Giant Magneto-impedance properties of Cr-incorporated Co-Fe-Si-B amorphous microwires

The investigation is focused on the effect of Cr incorporation for Co/Fe in (Co_0.5Fe_0.5)_78−xCr_xSi₈B₁₄ (x=0-12) amorphous microwires of 110 μm diameter prepared by in-water quenching technique. The rise in crystallization onset T_X1 with Cr addition revealed the elemental contribution against devitrification and a consequent thermal stability. Cr is unfavorable towards ferromagnetic ordering leading to a linear drop in Curie temperature T_ca with its rise in concentration. The presence of low Cr content upto Cr-4 at.% has been effective in drastically improving the Giant magneto-impedance (GMI) property. Cr content in the range of 4≤X≤10 has low magnetostriction and maximum field sensitivity in the as-quenched state. The GMI properties are further improved after annealing treatment. High content of Cr>10 is found to be deleterious towards GMI behavior and its consequent application as sensor material.     

Co基金属纤维不对称巨磁阻抗效应

以直径32 μm的熔体抽拉Co基非晶金属纤维为研究对象, 分析了该纤维不同激励条件下的巨磁阻抗(giant magneto impedance, GMI)效应. 实验结果表明: 这类纤维的GMI效应具有不对称性特点, 即 AGMI (asymmetric GMI)效应. 同时, 发现AGMI效应随激励条件不同而变化, 随交流频率或者激励幅值升高而逐渐增强; 当存在一定偏置电压时, AGMI效应大幅增强. 通过研究纤维的磁化过程, 分析了Co基金属纤维的AGMI效应. 由于Co基熔体抽拉纤维具有螺旋各向异性以及磁滞的存在使得GMI效应具有不对称性, 频率升高或者激励电流幅值增加有利于壳层畴环向磁化, AGMI增强. 当在纤维两端施加偏置电压时, 偏置电流诱发环向磁场增强了环向磁化, AGMI效应提高; 偏置电压较低时磁场响应灵敏度提高, 同时磁化翻转向高场移动, 阻抗线性变化对应的直流磁场区间增大. 这一方面拓宽了GMI传感器工作区间及灵敏度, 另一方面不利于获得更大的磁场响应灵敏度. 10 MHz (5 mA)激励时, 施加1 V强度的偏置电压后, 对应的磁场灵敏度从616 V/T 提高至5687 V/T; 偏置电压为2 V时, 灵敏度降低到4525 V/T. 因此, 可以通过适当提高环向磁场的方法获得大的磁场响应灵敏度及阻抗变化线性区域.     

AC-current-induced magnetization switching in amorphous microwires

We studied the influence of AC current flowing through microwires, on magnetization dynamics. We used a previously developed Sixtus-Tonks modified setup to evaluate the domain wall (DW) velocity within the microwire. However, instead of a magnetizing solenoid, we used a current flowing through the microwire. We observed that the AC current flowing through the annealed Co-rich microwire leads to remagnetization by fast domain wall propagation. The estimated DW velocity was approximately 4.5 km/s, which is similar to and even higher than that reported for the magnetic-field-driven domain wall propagation in Fe- and Co-rich microwires. We measured the DW velocity under tensile stress, and found that the DW velocity decreases under applied stress. An observed DW propagation induced by the current flowing through the microwire is explained considering the influence of an Oersted magnetic field on the outer domain shell. This field has a circular easy magnetization direction and magnetostatic interaction between the outer circumferentially magnetized shell and the inner axially magnetized core.     

Off-diagonal magnetoimpedance in stress-annealed amorphous ribbons

The influence of creep-induced magnetic anisotropy on the off-diagonal magnetoimpedance in amorphous Co₆₇Fe₄Cr₇Si₈B₁₄ ribbon is investigated. Hard-ribbon-axis anisotropy is produced by continuous stress annealing. On applying DC bias current, the off-diagonal impedance becomes an antisymmetric function of applied field with a quasi-linear part around the zero field. Theoretical explanation of the phenomenon is based on classical electrodynamics. It is shown that the maximum on the frequency dependence of off-diagonal impedance, observed around 1 MHz, results from competition between the electromagnetic induction and the skin effect. The quasi-linear characteristic can be utilized in low-cost high-sensitive magnetic field sensors.     

Physical properties and giant magnetoimpedance sensitivity of rapidly solidified magnetic microwires

The relation between the magnetoimpedance and the magnetic properties of a wide set of soft magnetic microwires from several sources has been studied. Magnetic properties were obtained by vibrating sample magnetometry and ferromagnetic resonance spectroscopy. The magnetoimpedance voltage sensitivity of each sample, the criterion of interest for high sensitivity magnetometer design, was then evaluated at several frequencies and drive currents. It appears that all samples possess roughly similar properties, regardless of their fabrication process or chemical composition. The voltage sensitivity of the samples obtained from experimental measurement is compared with a simple model of sensitivity. The general trends predicted by the model provide useful insights for materials optimization. Averaged sensitivity over the sample set is around 10 kV/T/cm at 10 MHz. The critical importance for sensitive magnetometry of the maximum excitation current permissible in each wire is also highlighted.     

Giant piezoresistance effects in silicon nanowires and microwires

The giant piezoresistance (PZR) previously reported in silicon nanowires is experimentally investigated in a large number of depleted silicon nano- and microstructures. The resistance is shown to vary strongly with time due to electron and hole trapping at the sample surfaces independent of the applied stress. Importantly, this time-varying resistance manifests itself as an apparent giant PZR identical to that reported elsewhere. By modulating the applied stress in time, the true PZR of the structures is found to be comparable with that of bulk silicon.     

High-frequency magnetoresonance absorption in amorphous magnetic microwires

The Fe₆₉Si₁₆B₁₀C₅, Co₇₅Si₁₀B₁₅, Co₆₈Mn₇Si₁₀B₁₅ amorphous microwires have been studied by the magnetoresonance absorption technique in the X (9.5 GHz), K (20–27 GHz) and Q (30–37 GHz) frequency bands. The specimens under study were metal threads of about 5 μm in diameter coated with dielectric Pyrex layer with thickness 5 μm. The dependences of magnetic resonance spectra on frequency and wire orientation have been measured. The analysis of the resonance signal parameters has revealed that well-known classical equations for FMR in a cylindrical-shaped sample could not be applied for these microwires. It is shown that due to the skin depth effect the model of hollow cylindrical tube has to be applied to explain the experimental results in the frequency range measured. The values of saturation magnetization, g-factor and anisotropy field have been estimated from the frequency dependence of the field for resonance.     

Domain wall propagation in Fe-rich amorphous microwires

The domain wall (DW) propagation in magnetically bistable Fe₇₄Si₁₁B₁₃C₂ amorphous microwires with metallic nucleus diameters of 12–16 μm has been investigated in order to explain high DW velocities observed in Sixtus–Tonks like experiments. In micrometric wires, the boundary between two head-to-head domains is very elongated. The DW mobility normal to the wall surface is reduced by the domain aspect ratio and is in the range of a few m/s/Oe in the linear regime. The experimental results in the viscous regime could be quantitatively explained in terms of the domain length and normal mobility limited by the eddy currents and spin relaxation losses.     

Microstructure-controlled enhancement of magnetoimpedance in nanocrystalline FeSiNbBCu alloys

Rapidly solidified amorphous Fe_68.5Si_18.5Nb₃B₉Cu₁ ribbon has been subjected to heat treatment at a temperature of 550 °C for different time periods. All the annealed ribbons show the precipitation of nanocrystalline Fe₃Si phase from the amorphous phase. The estimated crystallite size from X-ray diffraction peak analysis was in the range of 15-25 nm. While the surface studies confirm the presence of a distribution of spherical nanostructures in amorphous matrix. Both magnetoimpedance and longitudinal permeability ratios are found to increase with annealing time, and attain a maximum value for 60 min annealed ribbon and decrease on further increase in the annealing time. The enhanced magnetic properties and magnetoimpedance on suitable heat treatment is attributed to the change of magnetic parameters such as anisotropy and magnetostriction, due to change in microstructure. Analysis of permeability and impedance data taken under similar conditions suggests a strong correlation between them.     

Giant magnetoimpedance for biosensing: Advantages and shortcomings

Biosensors are an important area of modern sensor applications. Magnetoimpedance (MI) phenomenon was proposed for biosensing in 2003. Since that MI biosensor prototypes based on amorphous ribbons, multilayered structures, amorphous rapidly quenched wires and glass covered microwires were designed and tested. In this paper the advantages and shortcomings of MI-based devices for magnetic labels or label-free biodetection are discussed in view of recent results.     

Fast domain wall dynamics in amorphous glass-coated microwires

Here we report on the domain wall dynamics in amorphous glass-coated FeCuNbSiB microwires measured in the temperature range from 77 up to 400 K. At low temperatures below 200 K, the domain wall velocity is proportional to the applied magnetic field. At temperatures above 200 K, two regions have been found: one with low domain wall mobility at low fields and another one with high domain wall mobility at high fields. The different regions of the domain wall dynamics are treated in terms of the change of the domain wall configuration from transversal to vortex one. Moreover, non-linear regime is shown at low fields at the temperature 373 K as a result of the domain wall interaction with the local defects.     

Giant magneto impedance in electroplated NiFeMo/Cu microwires

Electroplated soft magnetic FeNiMo alloy films on Cu mircrowires show magneto impedance effects larger than 1000%. The magnetic anisotropy generated by the axial deposition of the alloy seems to be an important factor for the achievement of magnetoimpedance. The extent of this effect also increases with the layer thickness. Furthermore, the impedance is markedly improved after the annealing of the coating under an external magnetic field.     

Study of surface magnetic properties in Co-rich amorphous microwires

Magneto-optical investigations carried out on a Co-rich glass-covered amorphous microwire is presented. The appearance of circular magnetic bistability and the influence of tensile stress and high-frequency electric current on the surface magnetization reversal have been studied. The change of the mechanism of the magnetization reversal induced by the high-frequency electric current is also discussed.     

Magnetic structure of Fe-based amorphous and thermal annealed microwires

The magnetic structure of amorphous and thermal annealed glass coated microwires is studied by thermomagnetic, DSC, and Bitter domain pattern techniques. The long-range dipolar interaction between parallel aligned microwires and the appearance of large Barkhausen jumps steps in the axially magnetized loops are discussed in terms of reversal magnetization process.