Silica gel modified with Eriochrome Blue SE as a sorbent in trace analysis for metal ions

The sorption of 14 metal ions on silica gel impregnated with a mixture of Aliquat 336 and Eriochrome Blue SE was investigated. It was found that the sorption behaviour depends upon the species and the pH of the loading solution. Alkali metal ions were not retained under any of the investigated conditions. The retained metal ions can be eluted with dilute solutions of hydrochloric or perchloric acid without significant elution of the chelating reagent from the sorbent. The sorbent was used for the separation of metal ion mixtures by column — extraction chromatography and for additional purification of some salt solutions from trace amounts of Zn, Cd, Pb and Cu. The effectiveness of purification was confirmed by anodic stripping voltammetry.     

Ultrasound-Assisted Extraction for the Evaluation of Element Mobility in Bottom Sediment Collected at Mining and Smelting Pb–Zn Ores Area in Poland

The current BCR procedure for metal fractionation recommended by the Standard Measurement and Testing Programme requires rather time-consuming sample pretreatment. Ultrasonic energy seems to be an attractive alternative for leaching metal from solid samples into a liquid extractant phase. This study aims at optimizing ultrasonic extraction in order to replace the BCR method of leaching using acetic acid and to apply the procedure of assessing element mobility in bottom sediment rich in moderately soluble carbonate minerals. The application of ICP-MS allowed the determination of As, Cd, Cr, Cu, Pb, Ni, Tl and Zn in extracts, in a wide range of concentration without any special treatment. Finally, 40’min extraction in an ultrasonic bath was proposed for evaluation of the mobile fraction of As, Cd, Cr, Cu, Pb and Zn as an assessment of environmental risk. The recovery of the ultrasound-assisted extraction in comparison to the shake-filter method, as applied in the common BCR procedure, was slightly higher than 100% for As, Cr and Pb, reasonably high (about 70%) for Cd, Zn and Cd, but did not exceed 21% for Tl. Also, the mobility and extractability (relative mobility) of the studied elements from sediment collected over one year were compares. According to the results obtained after 40’min of ultrasound-assisted extraction it can be concluded that mobility did not change over one year for Cr, Cu, As, Cd, Ni and Tl, but noticeable differences for Zn and Pb were observed. The total content of all studied elements was almost the same in samples taken in the years 2003 and 2004, respectively.     

Complex formation between phytic acid and divalent metal ions: a solution equilibria and solid state investigation

An investigation on the complex formation equilibria between divalent metal ions Me (with Me=Mn, Co, Ni, Cu, Cd, and Pb) and phytic acid (H(12)L) is presented. Experiments were performed through a potentiometric methodology by measuring, at 25 degrees C, the proton and, in some cases (Cu(2+), Cd(2+), and Pb(2+)), also the metal ion activity at equilibrium in solutions containing, besides the metal and the ligand, 3 M NaClO(4) as the ionic medium. Unhydrolyzed solutions of the metal ion at millimolar concentration levels were titrated with solutions of about 10 mM sodium phytate, until the formation of a solid phase took place (always at pH approximately 2.5, except in the case of Cu(2+), which formed soluble complexes up to pH approximately 3.3). Coulometry was employed to produce very dilute solutions of either Cu(2+), Cd(2+), or Pb(2+) of accurately known composition. The emf data were explained by assuming, in the acidity interval explored, the formation of the complexes of general stoichiometry MeH(5)L(5-) and Me(2)H(3)L(5-). Coordination compounds in the solid state were also synthesized and characterized by elemental analysis, thermal analysis, and ICP spectroscopy. The solids had a general stoichiometry Me(6)H (t)LCl (t). x H(2)O, with the following t and x values for each metal investigated: Me ( t; x) = Mn (4; 2); Co (4; 2); Ni (4; 2); Cu (2; 2.5); Zn (2; 1); Sn (6; 6).     

Polymeric zinc ferrocenyl sulfonate as a molecular aspirator for the removal of toxic metal ions

A porous bilayered open coordination polymer [Zn(4,4'-bpy)(2)(FcphSO(3))(2)](n) (1; FcphSO(3)Na=m-ferrocenyl benzenesulfonate), has been assembled from Zn(NO(3))(2), m-ferrocenyl benzenesulfonate, and the bridging ligand 4,4'-bipyridine (4,4'-bpy). Ion-exchange induced products [Cd(0.6)Zn(0.4)(4,4'-bpy)(2)(FcphSO(3))(2)](n) (2), [Zn(0.75)Pb(0.25)(4,4'-bpy)(2)(FcphSO(3))(2)](n) (3), and [Cu(0.5)Zn(0.5)(4,4'-bpy)(2)(FcphSO(3))(2)](n) (4) could be obtained directly by suspending a big single crystal of 1 into concentrated solutions of Cd(NO(3))(2), Pb(NO(3))(2), and Cu(NO(3))(2), respectively. Most importantly, the big single crystal of 1 could be partly regenerated after immersion into concentrated aqueous solutions of Zn(NO(3))(2). On the other hand, powdered 1 could also be used as a metal ion adsorbent because of the well-defined pore size and pore shape. Ion exchange takes place along with the process of ion sorption. The big single crystal of 1 removes harmful metal ions by means of ion exchange, whereas powdered 1 removes toxic metal ions mainly through ion sorption. Also, compound 1 could be employed as a multi-ion analysis fluorescent probe to detect dangerous metal ions, such as Pb(2+), Cd(2+), Ag(+), and Cu(2+). The compounds described in this study may have potential applications in the design of new molecular devices.     

An Electrochemical Study of the Interactions Between Trace Metals and Humic Substances in Freshwaters by Anodic Stripping Voltammetry with a Thin Mercury Film Rotating Disk Electrode

An improved theoretical approach to Anodic Stripping Voltammetry with a Thin Mercury Film Rotating Disk Electrode for elucidating the nature of the interactions of Pb(II), Cd(II) and Zn(II) with humic substances in model solutions of Laurentian fulvic acid, and of Pb(II), Cd(II), Zn(II) and Cu(II) in freshwaters, is presented. Conditional stability constants of Pb(II), Cd(II) and Zn(II) complexes decreased with the ionic potential (z²/r) and increased with softness of the metal ion, indicating strong affinity of soft, polarizable donor ligands on humic substances for softer metal ions, resulting in an appreciable covalent character in electrostatic bonding between the metals and humic substances.     

Synthesis and analytical properties of a chelating resin functionalised with bis-(N,N'-salicylidene)1,3-propanediamine ligands

A polystyrenedivinylbenzene-based macroreticular resin was functionalised with bis-(N,N'-salicylidene)1,3-propanediamine ligands and its analytical properties have been investigated. The pH dependence of metal resin chelation has been determined for Cu(II), Ni(II), Co(II), Zn(II), Fe(II), Mn(II), Pb(II), Cd(II) and Cr(III). Trace amounts of these metal ions were quantitatively retained on the resin at neutral pH and easily recovered by elution with 1 N hydrochloric acid. The resin exhibits good chemical stability and fast equilibration with the metal ion making it useful for rapid concentration of trace amounts of metal ions on the resin columns.     

Preparation and analytical properties of a chelating resin functionalized with 1-hydrazinophthalazine ligand

A poly[styrene-co-(divinylbenzene)] resin (XAD-4) functionalized with 1-hydrazinophthalazine ligand has been prepared and its analytical properties investigated. The pH dependence of sorption of metal ion on the resin has been determined for Cu(II), Ni(II), Co(II), Zn(II), Cd(II), Pb(II), Fe(III) and Cr(III). Trace amounts of these metal ions were quantitatively retained on the resin and recovered by eluting with 1 mol l(-1) hydrochloric acid. The resin was found to be selective for Fe(III) and its separation from other metal ions was carried out effectively. Metal ions concentrations were determined using AAS.     

A new chelating resin for preconcentration and determination of Mn(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II) by flame atomic absorption spectrometry

A new polychelatogen, AXAD-16-1,2-diphenylethanolamine, was developed by chemically modifying Amberlite XAD-16 with 1,2-diphenylethanolamine to produce an effective metal-chelating functionality for the preconcentration of Mn(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II) and their determination by flame atomic absorption spectrometry. Various physiochemical parameters that influence the quantitative preconcentration and recovery of metal were optimized by both static and dynamic techniques. The resin showed superior extraction efficiency with high-metal loading capacity values of 0.73, 0.80, 0.77, 0.87, 0.74, and 0.81 mmol/g for Mn(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II), respectively. The system also showed rapid metal-ion extraction and stripping, with complete saturation in the sorbent phase within 15 min for all the metal ions. The optimum condition for effective metal-ion extraction was found to be a neutral pH, which is a great advantage in the preconcentration of trace metal ions from natural water samples without any chemical pretreatment of the sample. The resin also demonstrated exclusive ion selectivity toward targeted metal ions by showing greater resistivity to various complexing species and more common metal ions during analyte concentration, which ultimately led to high preconcentration factors of 700 for Cu(II); 600 for Mn(II), Ni(II), and Zn(II); and 500 for Cd(II) and Pb(II), arising from a larger sample breakthrough volume. The lower limits of metal-ion detection were 7 ng/mL for Mn(II) and Ni(II); 5 ng/mL for Cu(II), Zn(II), and Cd(II), and 10 ng/mL for Pb(II). The developed resin was successful in preconcentrating metal ions from synthetic and real water samples, multivitamin-multimineral tablets, and curry leaves (Murraya koenigii) with relative standard deviations of < or = 3.0% for all analytical measurements, which demonstrated its practical utility.     

仲壬基苯氧基乙酸萃取金属离子

Eu3+;二价金属离子;仲壬基苯氧基乙酸萃取金属离子     

Microwave assisted extraction for trace element analysis of plant materials by ICP-AES

Application of microwave assisted extraction for the decomposition and dissolution of plant samples for trace metal determination by ICP-AES was examined. Dried onion, leaves of spinach beet and three reference materials CTA-OTL-1, CTA-VTL-2 and CL-1 were analyzed. Water, EDTA and hydrochloric acid (0.01, 0.10 and 1.0 M, respectively) were used as leaching solutions. The extraction efficiency was investigated by comparison of the results with those obtained after microwave wet digestion. HCl was found to be very suitable for quantitative extraction of B, Ba, Cd, Cu, Mn, Ni, Pb, Sr and Zn from the samples. For reference materials, the measured concentrations are well consistent with the certified values. The use of EDTA led to a complete extraction of B, Cd, Ni, Pb, Sr and Zn. Water was found to be a good leaching solution for boron. For extraction with HCl and EDTA, the RSD values for the concentrations measured were below 8% for most of the elements.     

Metal-ion-coordinating properties of the dinucleotide 2'-deoxyguanylyl(5'-->3')-2'-deoxy-5'-guanylate (d(pGpG)3-): isomeric equilibria including macrochelated complexes relevant for nucleic acids

The interaction between divalent metal ions and nucleic acids is well known, yet knowledge about the strength of binding of labile metal ions at the various sites is very scarce. We have therefore studied the stabilities of complexes formed between the nucleic acid model d(pGpG) and the essential metal ions Mg2+ and Zn2+ as well as with the generally toxic ions Cd2+ and Pb2+ by potentiometric pH titrations; all four ions are of relevance in ribozyme chemistry. A comparison of the present results with earlier data obtained for M(pUpU)- complexes allows the conclusion that phosphate-bound Mg2+ and Cd2+ form macrochelates by interaction with N7, whereas the also phosphate-coordinated Pb2+ forms a 10-membered chelate with the neighboring phosphate diester bridge. Zn2+ forms both types of chelates with formation degrees of about 91% and 2.4% for Zn[d(pGpG)]cl/N7 and Zn[d(pGpG)]-cl/PO, respectively; the open form with Zn2+ bound only to the terminal phosphate group, Zn[d(pGpG)]-op, amounts to about 6.8 %. The various intramolecular equilibria have also been quantified for the other metal ions. Zn2+, Cu2+, and Cd2+ also form macrochelates in the monoprotonated M[H;d(pGpG)] species (the proton being at the terminal phosphate group), that is, the metal ion at N7 interacts to some extent with the P(O)2(OH)- group. Thus, this study demonstrates that the coordinating properties of the various metal ions toward a pGpG unit in a nucleic acid differ: Mg2+, Zn2+, and Cd2+ have a significant tendency to bridge the distance between N7 and the phosphate group of a (d)GMP unit, although to various extents, whereas Pb2+ (and possibly Ca2+) prefer a pure phosphate coordination.     

Extraction and separation of mercury(II) using triisobutyl phosphine sulfide (TIBPS/Cyanex) as an extractant and its application to industrial effluent

Studies have been carried out on the extraction of Hg(II) along with Cr(III), Fe(III), Mn(II), Co(II), Ni(II), Cu(II), Zn(II), Cd(II), Pb(II) and Ag(I), from mineral acid media using TIBPS. The effect of different variables influencing extraction of Hg(II), such as, mineral acid used, nature of diluent, concentration of metal ion and extractant has been investigated. Based on the partition data some binary separations from Hg(II) have been achieved. The potential of the extractant for decontaminating Hg from paper industry effluent has been assessed.     

Determination of Metal Ions in Natural Waters by Flame-AAS after Preconcentration on a 5-Amino-1,3,4-Thiadiazole-2-Thiol Modified Silica Gel.

ABSTRACT

5-amino-1,3,4-thiadiazole-2-thiol groups attached on a silica gel surface have been used for adsorption of Cd(II), Co(II), Cu(II), Fe(III), Ni(II), Pb(II) and Zn(II) from aqueous solutions. The adsorption capacities for each metal ion were (in mmol.g^?1): Cd(II)= 0.35, Co(II)= 0.10, Cu(II)= 0.15, Fe(III)= 0.20, Hg(II)= 0.46, Ni(II)= 0.16, Pb(II)= 0.13 and Zn(II)= 0.15. The modified silica gel was applied in the preconcentration and quantification of trace level metal ions present in water samples (river, and bog water).     

Partition and determination of cadmium, copper, lead and zinc in marine suspended particulate matter

A method for the determination of Cd, Cu, Pb, and Zn in the total and acetic acid (25%) soluble fraction of suspended particulate matter collected on Nuclepore membranes is described. The acetic acid leaching was carried out in a modified Millipore vacuum filtration apparatus. The total sample and the acetic insoluble fraction were decomposed in teflon bombs with HF/aqua regia. Flame or graphite furnace AAS was used for metal determinations. Sequential acetic acid extractions (3) show that on the average 76.4-92.0% of the metals are removed with the first extraction. Cadmium is potentially most easily available to biota with 90.4% of the total metal concentration located in the acetic acid soluble fraction.     

Group preconcentration of ions from acid aqueous solutions with a low-melting extractant

A possibility of the analytical application of a low-melting extractant, antipyrinium acetylsalicylate, to the extraction of a number of ions from acid aqueous solutions is studied. The distribution of Al, As, Cd, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, Sb, Sn, Ti, V, and Zn ions between the aqueous solution and an organic extractant is studied by atomic emission spectrometry. The efficiency of ion extraction from acid solutions with a low-melting flux of antipyrinium acetylsalicylate is calculated. It is shown that single extraction with an extractant flux ensures the efficient extraction of Fe, Mo, Sn, and Ti from the water phase of the analyzed solution to the flux. The introduction of chloride ions into the analyzed acid aqueous solution significantly increases the efficiency of the group preconcentration of ions by the ion-exchange mechanism.     

Selective separation of Hg(II) from aqueous solutions by the precipitate flotation technique

Summary The flotation of Hg(II) ions as sulphide or iodide from aqueous solutions has been investigated, using oleic acid as surfactant. Selective separation from Cd ions has been achieved. There was no interference by Bi, Pb, Cu, Cd, Mn, Zn, Co or Ni.     

Microwave assisted extraction for trace element analysis of plant materials by ICP-AES

Application of microwave assisted extraction for the decomposition and dissolution of plant samples for trace metal determination by ICP-AES was examined. Dried onion, leaves of spinach beet and three reference materials CTA-OTL-1, CTA-VTL-2 and CL-1 were analyzed. Water, EDTA and hydrochloric acid (0.01, 0.10 and 1.0 M, respectively) were used as leaching solutions. The extraction efficiency was investigated by comparison of the results with those obtained after microwave wet digestion. HCl was found to be very suitable for quantitative extraction of B, Ba, Cd, Cu, Mn, Ni, Pb, Sr and Zn from the samples. For reference materials, the measured concentrations are well consistent with the certified values. The use of EDTA led to a complete extraction of B, Cd, Ni, Pb, Sr and Zn. Water was found to be a good leaching solution for boron. For extraction with HCl and EDTA, the RSD values for the concentrations measured were below 8% for most of the elements. Received: 4 May 2000 / Revised: 20 June 2000 / Accepted: 22 June 2000     

Sorption and preconcentration of some heavy metals by 2-mercaptobenzothiazole-clay

2-Mercaptobenzothiazole loaded on previously treated clay was prepared, characterized and used for sorption and preconcentration of Hg(II), Pb(II), Zn(II), Cd(II), Cu(II) and Mn(II) from an aqueous solution. The support used was a natural clay previously treated with sulphuric acid solution. Adsorption isotherms of metal ions from aqueous solutions as function of pH were studied at 298 K. Conditions for quantitative retention and elution were established for each metal by batch and column methods. The chemically treated clay was very selective to Hg(II) in solution in which Zn(II), Cd(II), Pb(II), Cu(II) and Mn(II) were also present.     

Dynamic conductivity measurements in humic and fulvic acid solutions

Conductivity changes of dilute aqueous humic and fulvic acids solutions were monitored after the addition of small quantities of Cu, Cd, Pb, and Zn. The solutions were stirred at a constant and reproducible rate, and measurements proceeded until stable conductivities were attained. The values were compared to KCl reference solutions treated in an identical manner, and the results showed that the humic materials significantly reduced metal ion mobilities. Pb and Cu were affected more than Cd and Zn, and especially Zn regained a significant portion of its mobility upon dispersal. Cu, in contrast, was strongly and irreversibly retarded in all cases. It was inferred that Zn underwent transient electrostatic interactions with humics at high local concentration, while associations between Cu and humics were rapid and permanent. Different humic materials showed these effects to different extents. Raising the temperature from 20 to 60 °C did not, as expected, lead to higher relative conductivities in metal-humate solutions, but showed enhanced retardation of the cations. It was noted that temperature induced aggregation (clouding) of humic solutions increased the effective sizes of the metal-humate complexes, reducing their mobilities in aqueous solution.     

Metal chelate exchange in the organic phase-III Extraction and exchange constants of dithizonates and oxinates

Reactions between dithizonates and oxinates of Ag, Tl(I), Cu(II), Zn, Cd, Hg(II), Pb, Co(II), Ni, Pd, In, Ga and Bi in chloroform have been studied spectrophotometrically. From the exchange constants determined, the extraction constants of metal dithizonates or metal oxinates have been calculated. By this method extraction constants of many metal chelates can be calculated which are difficult to determine by studies of distribution between aqueous and chloroform phases.