Indirect determination of cyanide in water by atomic-absorption spectrophotometry

An indirect method for determination of trace cyanide in water by atomic-absorption spectrophotometry is described. Cyanide forms a stable complex anion with Pd in alkaline solution. This complex anion can form an ion-association complex with tetra-alkylammonium ions which can be extracted into n-butyl alcohol with an efficiency higher than 90%. The extract can be analysed directly for palladium (and hence indirectly for cyanide) by flame atomic-absorption spectrophotometry. The detection limit for cyanide by this method is 0.1 mug ml in the n-butyl alcohol extract. Beer's law is obeyed for 0.13-9 mug of CN(-) per ml of n-butyl alcohol. Several foreign ions do not interfere.     

Spectrophotometric determination of zinc bis-ethylenedithiocarbamate (zineb)

A spectrophotometric method has been developed for the determination of zineb by converting it into a molybdenum ethylenedithiocarbamate complex, which is then extracted into isobutyl methyl ketone and measured at 670 nm against a reagent blank. Beer's law is obeyed over the zineb concentration range 2-40 mug/ml in the extract. The method is sensitive and can be used for determination of zineb in the presence of ziram, thiram or ferbam.     

Simultaneous third-derivative spectrophotometric determination of copper and nickel in iron alloys and aluminium alloy

A method is proposed for the simultaneous determination of copper and nickel by third-derivative spectrophotometry based on the absorption spectra of their complexes with cyanide ion in the ultraviolet range. The method allows the determination of 0.55-5.8 mug/ml of copper and 0.55-6.8 mug/ml of nickel. The relative standard deviation for 11 determinations of 1.5 mul/ml of copper and nickel were 0.78 and 0.72%, respectively. The detection limits were 0.10,mug/ml for nickel and 0.13 mug/ml for copper. The method has been applied to direct determination of copper and nickel in iron alloys and an aluminium alloy without any separation.     

Flow-injection chemiluminometric analysis of some benzamides by their sensitizing effect on the cerium-sulphite reaction

A simple, highly sensitive chemiluminescent method using flow injection is described for the determination of three substituted benzamides, namely: sulpiride, sultopride and tiapride. The method is based on the sensitizing effect of these drugs on the chemiluminometric oxidation of sulphite by cerium(IV). The different experimental parameters affecting the chemiluminescence intensity were carefully studied and incorporated into the procedure. The method permits the determination of 0.05-2.5 mug ml(-1) sulpiride, 0.01-2.5 mug ml(-1) sultopride hydrochloride and 0.01-1.5 mug ml(-1) tiapride hydrochloride with minimum detectability of 0.01 mug ml(-1). The method was applied to the determination of these benzamides in pharmaceutical preparations and biological fluids.     

Manual and fia methods for the determination of cadmium with malachite green and iodide

A sensitive and rapid spectrophotometric method for the determination of cadmium is described, based on the formation of a blue complex at pH 4 between the anionic iodide complex of cadmium(II) and Malachite Green; the colour is stabilized with poly(vinyl alcohol). The calibration graph for measurement at 685 nm is linear over the range 1-50 mug of cadmium per 25 ml of final solution, with a relative standard deviation of +/-1.7% for 1 mug/ml cadmium. The molar absorptivity is 6.1 x 10(4) 1.mole(-1).cm(-1). The method can be successfully adapted for FIA, the peak height being proportional to the cadmium concentration over the range 0.1-3 mug/ml; a two-channel manifold is used and an improvement in selectivity is obtained. The use of a gradient tube is demonstrated to give a good calibration for Cd(II) over the range 2 x 10(-2) -2 x 10(-6)M.     

Prediction of conditions for use of spectrophotometric reagents: p-dimethylaminobenzilidenerhodanine as a spectrophotometric reagent for silver and palladium

A method for theoretical estimation of the detection limits of spectrophotometric reagents is reported. The concentration limits of Beer's law when p-dimethylaminobenzilidenerhodanine is used for determination of silver and palladium are defined on the basis of the stability constants. Conditions for determination of 2-10mug, of Ag per 25ml and 1-5mug of Pd per 25ml with standard deviation 0.03mug per 25 ml are proposed.     

铜的反催化分光光度法——铜(Ⅱ)-过硫酸钾-甲基红体系

本文提出一种利用铜在乙醇介质中阻抑过硫酸钾氧化甲基红来测定痕量铜的新方法。采用动力学光度法可测定低至0.4ng/ml Cu~(2+)。本法用于水和试剂中的测定,结果令人满意。     

Flow injection chemiluminescence determination of thiamine based on its enhancing effect on the luminol-hydrogen peroxide system

A new flow injection chemiluminescence (CL) method is proposed for the determination of thiamine, based upon its enhancing effect on the CL reaction of luminol with hydrogen peroxide in alkaline solution. The method allows the determination of thiamine within 0.05-8 mug ml(-1) range with a detection limit (3sigma) of 0.01 mug ml(-1). The relative standard deviation is 1.4% (n=11, 0.5 mug ml(-1) thiamine) and the sample throughput is about 90 samples h(-1). The method was successfully applied to the determination of thiamine in pharmaceutical preparations.     

Simultaneous determination of manganese and zinc in mixtures using first- and second-derivative spectrophotometry

A new direct spectrophotometric determination of manganese with 5,8-dihydroxy-1,4-naphthoquinone (naphthazarin,NAZA) is reported. Absorption maximum, molar absorptivity and Sandell's sensitivity of 1:2 (M:L) complex are 695 nm, 1.88x10(4) l mol(-1) cm(-1) and 2.92 ng cm(-2), respectively. A linear calibration graph is obtained up to a concentration of 7.2 mug ml(-1) of manganese. The optimum range for determination (Ringbom) is between 0.20 and 6.8 mug ml(-1). A rapid method for simultaneous determination of manganese and zinc in their mixture using derivative spectra is described. The range 0.28-5.6 mug ml(-1) manganese could be determined in the presence of 0.33-6.8 mug ml(-1) zinc and vice versa. The developed method was applied to the simultaneous spectrophotometric determination of manganese and zinc in some synthetic mixtures and was found to give satisfactory results.     

Extraction and spectrophotometric determination of titanium(IV) with alizarin and fluoride

The characteristics of the mixed-ligand titanium(IV)-fluoride-alizarin complex, including the optimum conditions of formation and extraction into methyl isobutyl ketone, are described. A simple and sensitive procedure for spectrophotometric determination of titanium has been developed. At pH 9.5-10.3 titanium reacts with alizarin in the presence of fluoride to form a red-violet complex that is completely extractable into methyl isobutyl ketone, and has its absorption maximum at 513 nm. The molar absorptivity at 513 nm is 7.0 x 10(4)l.mole(-1).cm(-1). Beer's law is obeyed up to 22 mug of titanium in 30 ml of solution. The method has been used for the determination of titanium in an oxide mixture and aluminium alloy samples.     

Application of photochemical inhibition in flow injection systems: Determination of epinephrine and L-dopa

An automated procedure for the photochemical determination of epinephrine and L-dopa has been developed. It is based on the strong inhibition by these catecholamines on the photochemical reaction between phloxin and ethylenediaminetetraacetic. The proposed flow-injection method allows the fluorimetric determination of epinephrine in the range 1.9-26.4 mug/ml and of L-dopa in the range of 1.5-12.7 mug/ml, with a sampling frequency of 35 samples/hr. The method was applied successfully to the determination of body catecholamines in pharmaceutical preparations.     

Permanganate-based chemiluminescence analysis of cefadroxil monohydrate in pharmaceutical samples and biological fluids using flow injection

A chemiluminescent method using flow injection is described for the determination of cefadroxil monohydrate. The method is based on the chemiluminescence reaction of cefadroxil with potassium permanganate in sulphuric acid, sensitized by quinine. The proposed procedure allows the determination of cefadroxil over the concentration range 0.1-30 mug ml(-1) with a detection limit of 0.05 mug ml(-1) and a sample measurement frequency of 150 samples h(-1). The method was successfully applied to the determination of cefadroxil in pharmaceutical preparations and biological fluids.     

Spectrophotometric multicomponent determination of sunset yellow, tartrazine and allura red in soft drink powder by double divisor-ratio spectra derivative, inverse least-squares and principal component regression methods

Double divisor-ratio spectra derivative (graphical method), classical least-squares and principal component regression (two numerical methods) methods were developed for the spectrophotometric multicomponent analysis of soft drink powders and synthetic mixtures containing three colorants without any chemical separation. The graphical method is based on the use of derivative signals of the ratio spectra using double divisor. In this method, the linear determination ranges were 2-8 mug ml(-1) sunset yellow, 4-18 mug ml(-1) tartrazine and 2-8 mug ml(-1) allura red in 0.1 M HCl. In the numerical methods, a training set was randomly prepared by using 18 samples containing between 0 and 8 mug ml(-1) of sunset yellow, 0-18 mug ml(-1) of tartrazine and 0-8 mug ml(-1) of allura red. The chemometric calibrations were calculated by using the prepared training set and its absorbances at seven points (from 375.0 to 550.0 nm) in the spectral region 325-584 nm. The proposed methods were validated by using synthetic ternary mixtures and applied to the simultaneous determination of three colorants in soft drink powders. The obtained results were statistically compared with each other.     

Atomic-absorption spectrophotometric determination of traces of manganese with thenoyltrifluoroacetone

An atomic-absorption spectrophotometric method for the determination of traces of manganese in solution with thenoyltrifluoroacetone (TTA) is described. Manganese(II) is extracted with 0.01M TTA in methyl isobutyl ketone (MIBK) at pH 9.5. The atomic-absorption of the organic phase at 279.5 nm is measured. Except for chromium, iron, hafnium, niobium, nickel, rhodium, tin, titanium and zirconium, microquantities of many other cations and anions do not interfere. Iron can be removed by MIBK extraction before the TTA extraction. The sensitivity of the method was 1.6 ng/ml for 1% absorption in aqueous solution. The method was successfully applied to the analysis of environmental waters. Manganese in the filtered fractions of water samples was reliably determined with relative standard deviations of 7% at the 5 mug/l. level and 1% at 50 mug/l.     

Automatic determination of cobalt at the submicrogram per millilitre level using a flowthrough spectrophotometric sensor

A flowthrough spectrophotometric sensor for the determination of cobalt at the nanogram per millilitre level using pyridoxal 4-phenylthiosemicarbazone as reagent and integrated preconcentration and detection in the flow cell is proposed. The method is highly selective for cobalt(II); it features detection and determination limits of 0.02 and 0.06 mug ml(-1) respectively, and a linear range of at least 0.04-18 mug ml(-1). The method is subject to very few interferences because the strongly acidic medium used prevents the formation of most complexes of the reagent with other metal ions. The method was applied to the determination of cobalt in pharmaceutical preparations.     

Determination of clenbuterol in pharmaceutical preparations by reaction with o-phthalaldehyde using a flow-injection fluorimetric procedure

A new procedure for the determination of clenbuterol is proposed using flow-injection and fluorimetric detection. The method is based on the derivatization reaction of the primary amine group with o-phthalaldehyde in the presence of 2-mercaptoethanol. The calibration graph based on peak area was linear in the range 0.2-5 mug ml(-1) and the detection limit was 0.06 mug ml(-1). The method was validated using a reference spectrophotometric procedure and was applied to the determination of the drug in commercial pharmaceutical preparations.     

Determination of total proteins: a study of reaction between quinones and proteins

A previous study was undertaken to test the reaction of several quinones (p-benzoquinone; 2,5-dichloro and 2,6-dichloro p-benzoquinone; tetrachloro-p-benzoquinone; tetrachloro-o-benzoquinone; 2,5-dichloro-3,6-dihydroxy-p-benzoquinone; benz[a]anthracene-7,12-dione) with bovine serum albumin (BSA). From this study, we have devised a spectrophotometric method for determination of total proteins. The quinone, tetrachloro-p-benzoquinone (p-chloranil), showed the best result. The product of reaction between proteins and p-chloranil absorbed at 360 nm and Beer's law was followed up to 200 mug ml(-1) of BSA. The product of reaction of BSA/p-chloranil was stable for 30 min, after that the absorbance increased 16% and kept stable for 24 h. The p-chloranil method showed a limit of detection (1.25 mug ml(-1)) lower than the biuret method (52.0 mug ml(-1)) or p-benzoquinone (PBQ) method (2.6-4.0 mug ml(-1)). The method was applied to spectrophotometric determination of total proteins in blood plasma; the results were compared with the biuret method that is widely used in clinical analysis.     

Simultaneous determination of iron and zinc by pH gradient construction in a flow-injection system

A flow-injection method for the simultaneous determination of iron and zinc in the human hair with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) using a pH gradient technique has been developed. The linear range for the determination of iron is 0.1 approximately 1.8 mug ml(-1) and for zinc is 0.2 approximately 5.0 mug ml(-1). About 20 approximately 30 samples can be determined in 1 h. The proposed method is simple, rapid and accurate. It has been applied to the simultaneous determination of trace amounts of iron and zinc in the human hair with satisfactory results.     

The separation of W(V) from HCl-KSCN medium on polyurethane foam sorbents for its spectrophotometric determination in steels and silicates

A simple procedure for selective sorption of tungsten is described. The method involves reduction of W(VI) to W(V) with tin(II) chloride (2%, w/v) at 8-9M hydrochloric acid, formation of the W(V)-SCN complex with 0.2M KSCN and its sorption on polyurethane foam within 20 min. The sorbed complex is then eluted with acidified acetone (1 ml of 1M hydrochloric acid and 8 ml of acetone) followed by addition of 1 ml of 0.1M KSCN to the eluent. The method has been applied to the spectrophotometric determination of tungsten in steels and silicates by measuring the absorbance of the eluted solution at 400 nm. Beer's law is obeyed for the range 0.1-12 mug W/ml. Other elements, e.g., Co(III) (50 mug/ml), Cu(II) (10 mug/ml), Ti(IV) (20 mug/ml), V(V) (10 mug/ml) and Mo(VI) (0.5 mug/ml) have no effect on the method. Interference of copper, up to 100 mug/ml has been eliminated by masking with thiourea and that due to molybdenum by prior separation with thioglycollic acid on PUF. The method has been verified with standard samples.     

Determination of trace europium based on new fluorimetric system of europium(III) with thenoyltrifluoroacetone and N,N'-dinaphthyl-N,N'-diphenyl-3,6-dioxaoctanediamide

In the present paper, N,N'-dinaphthyl-N,N'-diphenyl-3,6-dioxaoctanediamide acts as a specific reagent for enhancing the fluorescence intensity of Eu(III) complex with thenoyl trifluoroacetone (TTA), the spectrofluorimetric determination of trace amounts of Eu(III) based on the above system was carried out and its luminescence mechanism was studied. The excitation and emission wavelengths are 343.6 and 613.3 nm, respectively. The fluorescence intensities vary linearly with the concentration of europium(III) in the range 3.647x10(-3)-3.039 mug ml(-1) for the original fluorescence with a detection limit down to 2.279x10(-4) mug ml(-1) and the standard deviation is 0.063 mug ml(-1) for 10 times measurements, and in the range 7.598x10(-4)-0.0243 mug ml(-1) (SD=0.035 for 15 times measurements), 0.06078-0.6100 mug ml(-1) (SD=0.52 for 10 times measurements) for the first derivative fluorescence signal with a detection limit down to 8.566x10(-5) mug ml(-1). The interferences of other rare earths and some of inorganic ions are described. This method is a direct, rapid, selective and sensitive analytical method for the determination of trivalent europium in rare earth ore samples and high purity of rare earth oxides.