An investigation of a flameless atomic-absorption method for determination of aluminium, calcium, iron and magnesium in sewage sludge

The methods currently used for the determination of aluminium, calcium, iron and magnesium in sewage sludge are time-consuming. A rapid flameless atomic-absorption procedure, utilizing homogenization of diluted samples as the only pretreatment, has been compared with wet and dry analytical methods followed by flame atomic-absorption analysis, in a statistically designed experiment. Low-sensitivity (secondary absorption) lines have been used for the flameless analysis. The flameless atomic-absorption method described is better than all the other methods tested, with the exception of the nitric-perchloric-hydrofluoric acid digestion procedure. The time saved is substantial and the method could be used advantageously for routine analysis.     

Determination of chromium in low-alloy steels by atomic-absorption spectrophotometry

Iron causes severe depression of the signal in determination of chromium by atomic-absorption spectrophotometry in an air-acetylene flame. This effect can be eliminated by addition of hydroxylamine hydrochloride and use of a fuel-rich flame. Addition of iron to the standard solutions is not necessary for up to 300 ppm of iron in the test solution.     

Determination of gold, indium, tellurium and thallium in the same sample digest of geological materials by atomic-absorption spectroscopy and two-step solvent extraction

A rock, soil, or stream-sediment sample is decomposed with hydrofluoric acid, aqua regia, and hydrobromic acid-bromine solution. Gold, thallium, indium and tellurium are separated and concentrated from the sample digest by a two-step MIBK extraction at two concentrations of hydrobromic add. Gold and thallium are first extracted from 0.1M hydrobromic acid medium, then indium and tellurium are extracted from 3M hydrobromic acid in the presence of ascorbic acid to eliminate iron interference. The elements are then determined by flame atomic-absorption spectrophotometry. The two-step solvent extraction can also be used in conjunction with electrothermal atomic-absorption methods to lower the detection limits for all four metals in geological materials.     

Spectroscopy in separated flames-II The use of the separated air-acetylene flame in long path atomic absorption spectroscopy

The application of a separated air-acetylene flame to the determination of several elements by long-path atomic-absorption spectroscopy is described. The factors which govern the stability and reproducibility of the separated flame have been investigated. High sensitivity and stability and low background absorption are obtained in the the determination of zinc, iron, copper, mercury, magnesium and silver by the method described.     

Correlation between flame geometry and the absorbance of some elements in the presence of organic solvents

The correlation between the changes in flame geometry and the sensitivity of atomic-absorption determination of silver, copper, iron and lead in the presence of various solvents (water, ethanol, n-propanol, methyl acetate, ethyl acetate and acetone) has been investigated. The flame geometry was studied by the Schlieren technique. Organic solvents, allowing a greater rate of introduction of solution, enable a greater sensitivity to be achieved. However, owing to the expansion of the reaction zone, the increase in sensitivity is not as great as expected from the amount of sample introduced into the flame.     

Indirect method for the determination of aluminium by atomic-absorption spectrometry using an air-acetylene flame

The enhancement of the atomic-absorption signals of iron, cobalt, nickel and chromium in a fuel-rich air-acetylene flame by small amounts of aluminium makes possible the indirect determination of aluminium in the concentration range 0.01-10 ppm. The optimization of working conditions and the occurrence of interferences are reported.     

Rapid analysis of small glass fragments by atomic-absorption spectroscopy

A rapid method is described for the determination of magnesium, iron and manganese in small glass fragments (250-500 mug). The speed of the analytical procedure is made possible by the use of a convenient cold digestion stage allied to a discrete sampling method which permits the three elements of interest to be determined by flame atomic-absorption spectrophotometry.     

Determination of scandium in sea-water by atomic-absorption spectroscopy

A method for the determination of scandium in sea-water at the sub-microgram level has been developed. Scandium is coprecipitated with iron(III) hydroxide at pH 8-9, and then separated from the iron by ion-exchange. The final concentration is achieved by extracting the scandium into a solution of oxine in butanol. A nitrous oxide-acetylene flame is used for the determination by atomic-absorption spectroscopy. Recoveries of 99-100% are obtained. The storage of the solutions before analysis has been investigated by radiometric techniques with (46)Sc. The scandium concentration in surface waters of the South China Sea was found to be 0.01 +/- 0.005 microg/l .     

A comparison of methods for the determination of platinum in ores

Fire-assay and wet-extraction methods of determining platinum in ores have been evaluated. The fire-assay procedure using lead as a collector was used in combination with flame and flameless atomic-absorption, emission spectroscopy and X-ray fluorescence. In this last method flattened silver beads were analysed directly, whereas for the other methods the beads were dissolved in aqua regia and the solutions made up with concentrated hydrochloric acid before analysis. The wet procedures involved treatment of the ores with acids and subsequent analysis by flame atomic-absorption or by spectrophotometry after treatment with tin(II) chloride. Chromatographic, ion-exchange and solvent-extraction procedures were used to isolate platinum from base metals, the other platinum metals and gold. Results for each ore by fire assay-flame atomic-absorption, fire assay-emission spectroscopy, and wet extraction combined with spectrophotometry, showed no difference at the 99% confidence level. X-Ray fluorescence and flameless atomic-absorption results tended to be high and low respectively. The most precise method was wet extraction followed by spectrophotometric determination. Emission spectroscopy and X-ray fluorescence generally yielded the poorest precision. Wet-extraction methods were time-consuming and since no advantage was gained in accuracy over the fire-assay methods, a combined fire assay-flame atomic-absorption system was the preferred method of analysis.     

Precision and linearity of determinations at high concentrations in atomic-absorption spectrometry with horizontal rotation of the burner

The variation in precision of analytical measurements and linearity of analytical calibration curves resulting from a reduction of flame path-length by rotation of the burner head in flame atomic-absorption spectrometry is described. The precision is found to be approximately equivalent to that with the normal burner slot alignment, and the linear range is found to be improved in some cases. The application of burner rotation to determination of zinc in Standard Reference Material 1648-Urban Particulate Matter, is shown to provide precision and accuracy typical of flame atomic-absorption analysis.     

Spectrophotometric determination of the pH scale in ethane-1,2-diol

A highly selective method is described for the determination of gallium at the ppm-level in manganese nodules and geological reference samples. After dissolution of the sample, gallium is adsorbed on Dowex 1 (chloride form) from hydrochloric acid solution containing titanium trichloride, which reduces iron(III) so that it is not adsorbed. After elution with dilute nitric acid and evaporation, gallium is determined by atomic-absorption spectrometry with an air-acetylene flame.     

Matrix effects on the determination of manganese in geological materials by atomic-absorption spectrophotometry under different flame conditions

Suppression caused by five of the seven matrix elements studied (Si, Al, Fe, Ca and Mg) was observed in the atomic-absorption determination of manganese in geological materials, when synthetic solutions and the recommended oxidizing air-acetylene flame were used. The magnitude of the suppression effects depends on (1) the kind and concentration of the interfering elements, (2) the type of acid medium, and (3) the concentration of manganese to be determined. All interferences noted are removed or alleviated by using a reducing nitrous oxide-acetylene flame. The atomic-absorption method using this flame can be applied to the determination of total and extractable manganese in a wide range of geological materials without interferences. Analyses of six U.S. Geological Survey rock standards for manganese gave results in agreement with the reported values.     

Determination of gold in copper-bearing sulphide ores and metallurgical flotation products by atomic-absorption spectrometry

A method is described which is specific for the determination of gold in sulphide copper ores and concentrates. Direct decomposition with aqua regia was found to be incomplete. A carefully controlled roasting stage followed by treatment with hydrochloric acid and then aqua regia was effective for dissolving all the gold. The gold is extracted into 4-methylpentan-2-one (methyli-sobutylketone) then aspirated into a very lean air—acetylene flame and the gold determined by atomic-absorption spectrometry. No interferences were observed from large concentrations of copper, iron or nickel.     

Determination of lead in drinking waters by hydride generation and atomic-absorption spectroscopy, and three other methods

Simultaneous presence of copper and nickel in potable waters interferes with the determination of lead at trace levels by the hydride-atomic-absorption spectrophotometric method. This interference is eliminated by co-precipitating lead with manganese dioxide from acidic solution. The precipitate is dissolved in 0.85% nitric acid and analysed by the automated hydride-atomic-absorption method. This method has been applied to 22 representative water samples and results compared with those obtained by using differential pulse anodic-stripping voltammetry, flame atomic-absorption and graphite-furnace atomic-absorption spectrophotometry. The precision of the three methods is reported and their accuracy checked by the analysis of reference standard water samples. The sensitivity of the three methods is of the order of 1 mug/l., compared to 100 mug/l. for flame atomic-absorption. The merits of each method are discussed.     

Determination of tellurium in copper, lead and selenium by atomic-absorption spectrometry after extraction of the trioctylmethylammonium-tellurium bromide complex

A simple, rapid and sensitive combined solvent extraction and atomic-absorption spectrometric method has been developed for the determination of tellurium in copper, lead, selenium and blister copper. Tellurium is extracted as the trioctylmethylammonium-tellurium(IV) bromide complex into butyl acetate and determined by flame atomic-absorption spectrometry of the extract. As little as 1 mug of tellurium in a sample can be determined. The extraction of tellurium from hydrobromic acid solution with trioctylamine has also been investigated.     

Determination of traces of calcium, magnesium, iron and nickel in aluminium salts by atomic-absorption spectrophotometry with a microwave-excited source and hollow-cathode lamps

The determination of trace amounts of calcium and magnesium in solutions containing large concentrations of aluminium salts may be accomplished by co-precipitating their hydroxides on iron(III) hydroxide, dissolving the precipitate, and extracting the 8-hydroxyquinolates of calcium and magnesium into methyl isobutyl ketone at about pH 11. The extract may be sprayed into the airpropane flame of a simple unmodulated spectrophotometer and atomic-absorption measurements for calcium and magnesium made at 4227 and 2852 A respectively. The limits of determination correspond to 10 and 1 ppm of calcium and magnesium in solid alumina. Iron and nickel may be co-precipitated on hydrated manganese(IV) oxide and their 8-hydroxyquinolates extracted at pH 4.5. Measurements of atomic absorption for these elements at 2483 and 2320 A respectively yield limits of determination corresponding to 10 ppm in alumina. Hollow-cathode lamps may be used for calcium, magnesium and nickel, but a simple microwave-excited discharge tube gives much better sensitivity than a hollow-cathode lamp for iron.     

Analysis of sediments for heavy metals by a rapid electrothermal atomic-absorption procedure

A rapid electrothermal atomic-absorption spectrophotometric procedure with homogenization as the only pretreatment is compared with two wet pretreatment methods followed by flame atomic-absorption, in a statistically designed experiment. Samples from the top 5 cm of sediments at three different points of the Tejo estuary were used for the tests. The results show that the electrothermal procedure performed as well as whichever was the better of the flame methods for the determination of cadmium and nickel, irrespective of the sand content of the samples; although not statistically significant, there was apparently a decrease in recovery for chromium, copper and lead by the electrothermal method as the sand content of the sample increased. For zinc the electrothermal method gave results statistically different from those of the flame procedures when the sand content was high but not when the organic content of the sample was high. Because of the limited degree of replication (5 variates) the relative differences between the average values obtained by the three methods were significant only if they exceeded 15%. The electrothermal method has the advantage of substantially greater speed.     

The determination of eight elements in human liver tissue by flame atomic absorption spectrometry in sulphuric acid solution

A flame atomic-absorption spectrometric method is detailed for the determination of Ca, Mg, Zn, Fe, Cu, Mn, Rb and Cd in human liver tissue. Metal losses for three alternative sample destruction procedures are discussed; in the recommended procedure, low-temperature ashing in an oxygen plasma is followed by dissolution in sulphuric acid and aspiration into an air—acetylene flame. The necessity of close matching of the K, Na, phosphate and sulphuric acid contents for samples and standards is demonstrated for several elements. The accuracy of the method was established by using NBS SRM Bovine Liver and carefully prepared synthetic standards. The relative standard deviation is typically 5%, although variations in the blood content between portions of liver tissue lead to poorer precision for iron.     

Determination of indium in aluminium alloys by flame atomic-absorption spectroscopy and flame atomic-emission spectrometry

The use of flame atomic-absorption and atomic-emission spectrometry for the determination of indium in aluminium alloys is described. Two types of flame are used: air—acetylene and nitrous oxide—acetylene. The efrect of other ions, especially aluminium, has been studied, and the use of lanthanum as a releasing agent is proposed for both techniques, the amount used depending on the amount of aluminium present.     

Determination of silver in copper and lead metals and alloys and in zinc and selenium by atomic-absorption spectrometry after separation by extraction of the tri-n-octylmethylammonium-silver bromide complex

A simple and sensitive combined solvent extraction and atomic-absorption spectrometric method has been developed for the determination of silver in copper and lead metals and alloys and in zinc and selenium. Optimal conditions have been established for the extraction and determination of silver. Silver is extracted as the tri-n-octylmethylammonium-silver bromide complex and determined by atomic-absorption spectrometry by spraying the extract directly into the flame. As little as 0.2 mug of silver in a sample can be determined.