Liquid-state membrane electrode sensitive to bismuth(III)

A liquid ion-exchange electrode containing a tetrachloraethane solution of the complex of bismuth(III) with 5-mercapto-3-(naphthyl-1)-1,3,4-thiadiazol-2-thione is described. The electrode is sensitive to Bi³⁺. The slope of the calibration graph (electrode potential vs. concentration) is 18.7 mV/pBi in the pBi range 6.5–9.5 in ammonium acetate buffer (pH = 4.0). Bivalent cations and Al(III), Fe(III) and Th(IV) do not interfere (K_{Bi³⁺+,M²⁺}<10⁻⁵). The dissociation constant of bismuth acetate has been determined with the aid of the electrode.     

Determination of vanadium(V) by direct automatic potentiometric titration with EDTA using a chemically modified electrode as a potentiometric sensor

A chemically modified electrode (CME) was prepared and studied as a potentiometric sensor for the end-point detection in the automatic titration of vanadium(V) with EDTA. The CME was constructed with a paste prepared by mixing spectral-grade graphite powder, Nujol oil and N-2-naphthoyl-N-p-tolylhydroxamic acid (NTHA). Buffer systems, pH effects and the concentration range were studied. Interference ions were separated by applying a liquid-liquid extraction procedure.The CME did not require any special conditioning before using. The electrode was constructed with very inexpensive materials and was easily made. It could be continuously used, at least two months without removing the paste.Automatic potentiometric titration curves were obtained for V(V) within 5 × 10⁻⁵ to 2 × 10⁻³ M with acceptable accuracy and precision. The developed method was applied to V(V) determination in alloys for hip prothesis.     

Selective potentiometric determination of Bi(III) with a coated-wire electrode

A bismuth-selective electrode based on the chlorobismuthate(III) salt of Aliquat 336 is described. The electrode gives nearly linear response in the bismuth concentration range 10⁻¹–10⁻⁴M. The optimum solution conditions for operation of the electrode have been determined together with possible interference effects. The application of the electrode to analysis of samples containing large amounts of other metals is illustrated by the determination of bismuth in pharmaceuticals. The electrode is shown to give results by direct potentiometry and the standard-addition method which differ from atomic-absorption results by not more than 2%.     

Determination of uranyl ion by potentiometric titration using an uranyl-selective electrode

Summary A potentiometric titration of uranyl ion is described using an uranyl selective electrode based on a membrane containing a complex of UO₂-bis[di-4-(1,1,3,3-tetra-methylbutyl)phenyl phosphate] as an ion-exchanger and tritolyl phosphate as a solvent mediator. The titrations were carried out with various titrants: sodium hydroxide, potassium fluoride and sodium salts of acetate, oxalate and citrate. The equivalence points were determined by Gran's method. Good results were obtained by using sodium oxalate as a titrant for the determination of uranium in several samples of ammonium diuranate. The results were quite comparable with those obtained by X-ray fluorescence spectrometry.     

Determination of chlorine in silicate rocks by ion-exchange chromatography and direct potentiometry with an ion-selective electrode

The method has been developed for determination of chlorine in silicate rocks by ion-exchange chromatography and an ion-selective electrode.     

Determination of quaternary ammonium compounds by potentiometric titration with an ionic surfactant electrode: single-laboratory validation

A potentiometric titration for determining the quaternary ammonium compounds (QAC) commonly found in antimicrobial products was validated by a single laboratory. Traditionally, QACs were determined by using a biphasic (chloroform and water) manual titration procedure. Because of safety considerations regarding chloroform, as well as the subjectivity of color indicator-based manual titration determinations, an automatic potentiometric titration procedure was tested with quaternary nitrogen product formulations. By using the Metrohm Titrando system coupled with an ionic surfactant electrode and an Ag/AgCl reference electrode, titrations were performed with various QAC-containing formulation products/matrixes; a standard sodium lauryl sulfate solution was used as the titrant. Results for the products tested are sufficiently reproducible and accurate for the purpose of regulatory product enforcement. The robustness of the method was measured by varying pH levels, as well as by comparing buffered versus unbuffered titration systems. A quantitation range of 1-1000 ppm quaternary nitrogen was established. Eight commercially available antimicrobial products covering a variety of matrixes were assayed; the results obtained were comparable to those obtained by the manual titration method. Recoveries of 94 to 104% were obtained for spiked samples.     

Determination of Fe(II)-Fe(III) and Fe(III)-Ni(II) by the two-component potentiometric complexometric titration

Summary The two-component complexometric potentiometric titration has been applied to the simultaneous determination of Fe(III) and Fe(II), and of Fe(III) and Ni(II) in solution. In each case the two analytes were determined by reading the end-points directly from the titration curve. The end-points are determined in a sense arbitrarily, but they are repeatable and easy to be detected precisely. However, the apparent (found) analytical results are biased. They are effectively corrected with the use of a set of two calibration equations (uncomplete second degree polynomials), which approximate the relationship between found endpoints and true concentrations of analytes in solution. The regression coefficients in the equations are determined on the basis of titration data obtained for standard solutions whose compositions correspond to a 2² factorial. Permanent address: Department of Analytical Chemistry, Jagiellonian University, Krakow     

Determination of gold(III) alone or in some mixtures and alloys by potentiometric titration of iodide

The present work is an application of iodide to the reduction of gold(III), in an attempt to develop new method for gold(III) based on potentiometric back-titration of the excess of iodide with mercury(II). Although it was proved by calculation that the reduction of tetrachloroaurate to the metal should proceed quantitatively to completion, yet our experiments showed that the reduction under ordinary conditions, gave Au(I) in the form of a white precipitate of AuI. We succeeded to push the reduction with iodide to the metal by an excess of ethanol-ether catalyzed iodide at somewhat elevated temperature.With the experimental conditions established a reliable procedure have been developed involving a potentiometric finish which enabled accurate determination of gold(III), either alone or in some of its alloys.     

Determination of calcium in silicate rocks by potentiometric titration with ethyleneglycol-bis-(2-Aminoethylether)tetraacetic acid and a calcium-selective electrode

The method reported for the determination of calcium in silicate rocks involves titration with ethyleneglycol-bis(2-aminoethylether)tetraacetic acid (EGTA) to a potentiometric end-point. A Crytur calcium-selective electrode is used; the selectivity constants (K_ca,x) are less than 10^-3 for Mg, Ba, Sr, K and Na. The method can be used for calcium contents of 2% or higher (and exceptionally for lower contents), in the presence of up to 60% Mg, 33% AI, 17% Fe, 5% Ba, 5% Ti, and 2.5% Mn. Al, Fe and Ti are masked with sulphosalicylic acid, barium is precipitated as its sulphate, and manganese is bound as its cyanide complex. If the magnesium content is less than that of calcium, EDTA can be used as titrant, magnesium being masked with acetylacetone.     

Determination of antimony(III) by titration with chromium(VI)

Summary There is no need for a catalyst in the potentiometric or spectrophotometric titration of antimony(III) with chromium(VI). The failure of titrations using indicators is due to slowness of the oxidized indicator-Sb(III) reaction; the indicator reaction can be catalysed by iodine. The spectrophotometric titration yields accurate results, and shows that the Sb(III)-Cr(VI) reaction is rapid. Slowness in the potentiometric titration is due to unfavourable electrode kinetics.

---

Titration von Antimon(III) mit Chrom(VI)

Zusammenfassung Bei der potentiometrischen oder spektrophotometrischen Titration von Sb(III) mit Cr(VI) bedarf es keines Katalysators. Der Fehler bei Titrationen unter Verwendung eines Indikators hat seine Ursache in der langsam verlaufenden Reaktion zwischen dem oxydierten Indikator und Sb(III); die Indikator-Reaktion kann mit Jod katalysiert werden. Die spektrophotometrische Titration gibt genaue Resultate und zeigt, daß die Sb(III)-Cr(VI)-Reaktion rasch abläuft. Die Langsamkeit der potentiometrischen Titration ist durch die ungünstige Kinetik der Elektrode verursacht.

     

Determination of phosphorous in titanium bearing minerals by potentiometric titration using Pb-ion selective electrode

A method for phosphorous determination in titanium bearing minerals by potentiometric titration using a Pb-ion selective electrode has been developed. Sample decomposition is achieved by means of K(2)CO(3) fusion in a platinum crucible at 800 degrees C for 30 min in a muffle furnace, and subsequent leaching with water of the fused melt. The aqueous leachate is neutralised with HClO(4) and subsequent boiling. The obtained solution is used for titration with Pb(ClO(4))(2), and the Pb-ion selective electrode detects the end point. The lowest concentration determinable is 0.02% P(2)O(5) in a solid sample. The method was applied on in-house titanium bearing mineral samples and on IGS-31 ilmenite sample (British Geological Survey, UK). Synthetic samples were prepared and analysed, and phosphorous recovery is in the range 98-106%. The recovery and accuracy of the present method have been validated by spiking experiments and by comparing with the spectrophotometric values, respectively. The precision of the proposed method in terms of relative standard deviation is 2.0%.     

209Bi NQR study of bismuth(III) complexes

Potassium pentafluorobismuthate(III), nitrate-chloride Bi^III complexes MBiCl₃NO₃ (M=K, (NH₂)₂CNH₂), sulfate-chloride Bi^III complexes MBiCl₂SO₄ (M=K, Rb, NH₄, (NH₂(₂CNH₂), and Bi^III complexonates with the anions of ethylenediaminetetraacetic acid M[Bi(edta)]₂·nH₂O (M=Mg, Ca, Ni, Cd) and nitrilotriacetic acid Bi(nta)·2H₂O, and Bi(nta)·3thio·H₂O (thio is thiourea) were studied by²⁰⁹Bi NQR spectroscopy. A second-order phase transition was observed in K₂BiF₅ at 100 K. The compounds Bi(nta)·2H₂O, (NH₂)₂CNH₂BiCl₃NO₃, and MBiCl₂SO₄ (M=K, NH₄) are piezoelectrics. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 11, pp. 2237–2240, November, 1998.     

EDTA titration of bismuth(III) in ores and concentrates with biamperometric indication

Summary A method is described for the chelatometric titration of bismuth(III) with biamperometric indication. It is applied to ores and concentrates and can also be used in presence of interfering elements (as Zr, Tl, In, Mo, Cu, Fe).

---

Zusammenfassung Ein Verfahren wird beschrieben zur chelatometrischen Titration von Wismut(III) mit biamperometrischer Endpunktsanzeige. Es wird auf Erze und Konzentrate angewendet und kann auch in Gegenwart störender Elemente (wie Zr, Tl, In, Mo, Cu, Fe) benutzt werden.

     

Determination of antimony(III) and (V) in natural water by cathodic stripping voltammetry with in-situ plated bismuth film electrode

A method is described for the sequential determination of Sb(III) and Sb(V) using Osteryoung square wave cathodic stripping voltammetry. It employs an in-situ plated bismuth-film on an edge-plane graphite substrate as the working electrode. Selective electro-deposition of Sb(III)/Sb(V) is accomplished by applying a potential of ?500 mV vs. Ag/AgCl, followed by reduction to stibine at a more negative potential in the stripping step. Stripping was carried out by applying a square wave waveform between ?500 and ?1400 mV to the antimony deposited. The stripping peak current at ?1150 mV is directly proportional to the concentration of Sb( III)/Sb(V). The calibration plots for Sb (III) were linear up to 12.0?µg L^?1 depending on the time of deposition. The calibration plots for Sb (V) were linear up to 7.0?µg L^?1, also depending on the time of deposition. The relative standard deviation in the determination of 0.1?µg L^?1 of Sb(III) is 4.0% (n?=?5), and the limit of detection is as low as 2 ng L^?1. In case of 0.1?µg L^?1 Sb(V), the relative standard deviation is 3.0% (n?=?5) and the detection limit also is 2 ng L^?1. The method was applied to the analysis of river and sea water samples.     

Liquid state membrane electrode sensitive to Ln(III)

A liquid ion-exchange electrode containing a chloroform solution of the complex of Ln(III) (Gd, La) with tetraphenyl ester of imidodiphosphoric acid is described. The slope of the calibration graph (electrode potential vs concentration) is 18.5 mV/pLn in the pLn range 4.7-2 (pH = 5). Fe(III), Al(III), Co(II), Ni(II) and Ca(II) ions do not interfere, unlike ions of other lanthanides. It was found that the electrode might be applied to detect the end point of the titration of Ln(3+) ions.     

A study on the fluoride complexes of plutonium(III), samarium(III) and bismuth(III) using fluoride ion-selective potentiometry

Stability constants of the fluoride complexes of Pu(III), Sm(III) and Bi(III) in 1.0M NaClO₄/HClO₄ medium at 23±1°C have been determined by potentiometry using a fluoride ion-selective electrode. Plutonium was reduced to the trivalent state using quinhydrone with an excess to serve as holding reductant. The log values of concentration stability constants log ₁, log ₂, and log ₃ are 3.58, 6.40 and 12.61 for Pu(III), 3.23, 5.81 and 10.54 for Sm(III) and 3.69, 6.13 and 11.04 for Bi(III), respectively. The log ₂ values in all these cases have very large deviation and may be taken only as rough estimates.